Networking :: Using Ethernet To Power WiFi Network And Setting Up WiFi?
Aug 23, 2009
I have an old PowerBook G4 that I would like to use as a 'dummy' computer for learning wireless penetration (WEP/WPA attacks) more effectively. I had been using a wireless router, but I gave it away I can use Mac OS X to share an ethernet connection over wifi, but this is _very_ un-configurable. You get two options only, WEP and a key-length. So, I would like to install someway to make this wireless connection more configurable.
View 2 Replies
ADVERTISEMENT
Feb 5, 2011
I've been searching for a couple of hours and have not found any threads that solve my situation... hope I'm not repeating something here.
Setup: Notebook with openSUSE 11.2 using KDE 4. Using Network Manager to manage network connection (although I've tried configuring this using ifup as well with no luck).
I need to be able to connect to client networks via a network cable (Ethernet) and connect to the internet via my MiFi 2200 Mobile WiFi. Both cards/connections are active with the following:
I have no problem mounting drives from the client's network. But, can not reach the internet. If I disconnect the ethernet cable, the browser will immediately connect to the internet and load web pages.
I'm assuming the ethernet connection is taking precedence over the wireless connection?
I can't imagine that there is not a way to set this up. If Windows can do it, I'm sure openSUSE can!
View 9 Replies
View Related
Jan 31, 2011
I often use an Ethernet cable to connect my computer to another computer for various purposes. But when I do that, I cannot use the internet even though I'm still connected to a WiFi access point. I'm presuming that's because openSUSE is trying to reach the internet through the Ethernet cable, which has precedence over WiFi.Is there a way to enable internet usage via WiFi while I'm connected to another computer over Ethernet?
View 9 Replies
View Related
Jul 27, 2010
My WiFi can connect to internet without any problem, until I plug my ethernet cable ...then I lose internet.
So the question is : how do I configure my ip/dns and stuff to still have internet when I'm plugged by cable at the same time! it was working on windows ;-)
View 3 Replies
View Related
Nov 18, 2010
I have no Wifi on Battery Power?My wifi quits when power cord is pulled? I plug in the power cord and wifi works again?Dell XPS 16 1645 Ubuntu 10.10Much appreciated for a link to solve the problem or instructions
View 9 Replies
View Related
Jul 21, 2010
I was wondering if there's any way for a laptop to be both simultaneously connected to a wireless network, while at the same time acting as an ad-hoc network with local access to serve as a wifi connection for my mobile device, which would be ssh-ing into the laptop and using local resources.
View 1 Replies
View Related
Feb 14, 2010
I have an Asrock A330GC, with onboard ethernet, and an Engenius PCI card for wifi.I installed ubuntu server 9.10 no problems, and it picked up my ethernet in the installation with no difficulties.I couldn't get 9.10 to do what i wanted, so I tried installing 8.4 instead. This however didn't pick up any of the drivers, so i couldn't get online.So i reinstalled 9.10, only to find that no couldn't find network in the installation.Absolutely NOTHING has changed, the ethernet cable still plugged in, and if i plug same cable into my laptop, it works fine.Any ideas people?ifconfig doesn't mention any eth0, just lo, with an ip of 127.0.0.1 and amask of 255.0.0.0 which i'm fairly certain means its dead
View 1 Replies
View Related
Jan 29, 2011
just installed Ubuntu on my Macbook Pro and im loving it right now, but whenever I disconnect from the power source and run from battery, my wifi Internet slows down to a crawl. As soon as i plug the power back in, the internet is back to normal.
View 9 Replies
View Related
Feb 10, 2011
I am using ubuntu 9.10. in my area there are frequent power outage. So my wifi get disonnected as the router stops. And it asks for security code. So when power comes the router starts but i have to manually write the security code and connect to wifi again. how i can make the computer to auto connect to wifi after power comes.
View 3 Replies
View Related
Apr 2, 2010
I just installed UNR from a usb drive on my hp mini 1030nr. I followed a guide and got the drivers installed from the drive, but they would not activate in the restricted hardware dialog. I tried to run update over wired, but I couldn't get ethernet working. ifconfig -a anly shows lo, eth0 doesn't seem to exist. how to get wifi working?
View 9 Replies
View Related
Mar 21, 2011
i have installed 10.10 as a dual boot and when i go to wifi conections everything seems fine
when i click on conect to my router it wont conect, i also tried plugin in ethernet cable to router from laptop and still not conecting.
View 1 Replies
View Related
Aug 7, 2011
I tryed to get network work like this share internet from wifi (wlan0) to ethernet (eth0).So the internet connection comes from the wifi and we share to other computer via ethernet[URL]But when I restarted my pc then it dont work and network says "wired network device not managed" How can I get it work aigan ?[URL]Now I have anohter problem when I connect autoeth then the wireless network dosent work anymore, I have to disconnect eth0 to have wirelles network working. how can I manage to get the bowh to work?
View 2 Replies
View Related
Oct 9, 2015
I have Debian 8.2 with KDE 4.14 and everything runs perfect, except for the internet connection. This problem happens randomly when I turn on my machine. Sometimes when the desktop loads, the connection is already settled.
But sometimes when the desktop loads, the wifi icon is still loading and keeps stuck at "setting network address". Since this problem happens randomly I really don't know what is happening here. My wifi chip is this:
Code: Select all01:00.0 Network controller: Intel Corporation Centrino Wireless-N 130 (rev 34)
This is the problem:
I installed Debian with non-free firmware because of this chip.
View 6 Replies
View Related
Mar 7, 2011
root@debian:/etc/network# ifup wlan0
SIOCSIFFLAGS: Unknown error 132
SIOCSIFFLAGS: Unknown error 132
[code]...
View 1 Replies
View Related
May 30, 2009
im using fedora 10 with gnome on a laptop, i want to increase power to my wifi adapter as im only getting 40% connection strength to the nearest wifi AP (about 20 feet) in windows under power management there is a slider with best performance against battery life, is there a similar setup in fedora 10? ps, if explained fairly well, i dont mind shell scripting (bash) and compiling.
View 2 Replies
View Related
May 11, 2011
About 20 seconds after I unplug my Laptop from the AC adapter myiFi connection disconnects. The only way to get a connection again is to shut down my laptop and remove the battery and the AC adapter (WiFi-adapter reset) and reboot my laptop. I'm running 10.10 32-bit.lspci shows me these information about my WiFi-Adapter
02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Device 1a3b:1026
[code]....
View 9 Replies
View Related
Jul 26, 2011
After upgrading from 10.10 to 11.04 via the online upgrading method I had much trouble getting wireless to work but after following the instructions at .Driver/bcm43xx it burst into life, that is until I powered off and now I have to sudo modprobe b43 before the hardware button for the wifi will work and and then I am able to get online. This is for every power on session!! Once enabled it will switch on and off via the hardware button and the light is operational. Before the sudo modprobe b43 the buttonoes something as evidenced by sudo rfkill list after each press of the button. Is there any way to have the command sudo modprobe b43 inserted somewhere in the power on sequence? This was a working function on 10.10!
View 3 Replies
View Related
Aug 10, 2010
I have been trying to get my laptop to share its wireless connection to my older, wireless-less, computers through its ethernet port. So far, I have not been able to make it work. As far as I know, what I am trying to do is called network bridging. The method I have been trying so far is to run these commands as root:
Code:
ifconfig wlan0 -promisc
brctl addbr br0
brctl addif br0 wlan0
brctl addif br0 eth0
ifconfig br0 up
Each time I do this, the system running as a bridge loses connection, and the system being bridged to never gets a connection. My hardware is:
Code:
08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)02:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
View 3 Replies
View Related
Sep 30, 2010
I am a noob in Ubuntu and I would like to create and script or file which when clicked sets my WiFi interface's power lower, down to 7dBm. I already know how to do it by typing on the terminal, I just write:
#sudo -s
#my password
#iwconfig wlan0 txpower 7dBm
[code]...
View 2 Replies
View Related
Jan 10, 2011
Running Ubuntu 10.04. Networking won't work at all. Used to work flawlessly. Problem is not hardware, because booting windows (vista) on the same machine I can still use networking.
Little story: I Was going into a short trip, then I put my computer to sleep (as usual). Trip took longer than expected and, when I came back, the notebook battery was dead. Charged it, booted the notebook (Dell Inspiron 1525) and now its network won't work at all. After reboot it even ran a filesystem scan, but problem wasn't fixed. The icon on 'taskbar' only says "networking disabled". The ethernet lights won't even light up when I connect a ethernet cable and it won't see any wifi networks. I've tried to fiddle with that little switch which would turn the wifi on and off, but all it seems to do is turn the Bluetooth on and off, as shown by the little Bluetooth icon on 'taskbar' (I've not tested bluetooth, though). I've also tried to plug a external wifi dongle but ubuntu won't even try to install it.
what's happening or what could I do to get my network working? Is there some 'magic' I can type into a terminal window to make this work?
View 2 Replies
View Related
Feb 13, 2011
When I select the wifi icon on the panel, it just shows "No network devices available". I know my network can be found when I search with my iPhone, so I know there are networks to connect to. So, I checked the drivers, and it informs me that the B43 and STA drivers are not activated. So thats not a big deal, I guess, but when I use my ethernet cord, my laptop doesn't recognize/acknowledge (I'm not sure what the right term would be)it. I'm fairly sure I can't activate these drivers without an internet connection because when I do try, a message pops up saying "failed to fetch" with some long link.
My only guess is that it could be a hardware problem, but I really have no idea. I guess the ethernet problem is my only real problem. Because after I establish and internet connection the the rest is easy to fix.I'm sure its obvious, but I'll go ahead say that I'm a novice ubuntu user. I've only been working with it for about a week, but I'm learning alot.
View 9 Replies
View Related
Feb 8, 2011
I am basically wanting to use my Ubuntu 10.10 computer as a router. Note: Before you say just get a router please note that I am poor/cheap. I have two ethernet connections and one wireless connection on my netbook. I want to share the internet connection that is going into one of the ethernet cards through the other ethernet card and the wireless card.
DSL-->1sr Eth --> 2nd Eth (currently works)
DSL-->1sr Eth --> Wireless Card (Adhoc) <--(connects with limited connectivity AKA no internet)
The 2nd Ethernet card already has working internet, but when I connect to the Wireless card (through an Adhoc network), it cannot get an IP (I believe).
View 2 Replies
View Related
Jul 3, 2010
My laptop has an internal wireless device and a button to turn it on/off, but since it has bad reception I use an external USB wireless adapter.The problem is that if I turn the internal wireless device off using the button, it also turns the USB wireless adapter off.Is there anyway to use the killswitch (the button) only for the internal wireless device?This only started to happen in Ubuntu 10.04.
View 7 Replies
View Related
Apr 8, 2010
I have 2 connections, wlan and wired, and I'd want to have a few websites (in my browser) to connect through the wireless connection while other go through the wired rj45 connection. s it possible? (without unplugging the rj45 cable...)
View 2 Replies
View Related
Aug 29, 2009
I have only had a few weeks worth of experience with linux, so I'm probably considered a newbie at this but I felt like giving it a shot. I just configured my new Toshiba Satellite A505-S6969 to jaunty. Most of the transition is going well but I'm stuck with a few issues, one of which is getting my wifi to work. Right now I'm working off of an ethernet cable.spci returns
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port
[code]...
View 3 Replies
View Related
Mar 6, 2010
Installed ubuntu 9.10 dual boot with win7 yesterday. Everything working but Wifi. Wifi works fine with Win7. No Wifi in Ubuntu. Very confused. I have info from the wifi trouble ticket post.There does not seem to be a driver for this card anywhere.
lawrence@lawrence-laptop:~$ lspci
00:00.0 Host bridge: Intel Corporation X58 I/O Hub to ESI Port (rev 13)
00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13)
[code]....
View 9 Replies
View Related
May 13, 2009
the only error message I can find comes from "dmesg|tail"all it shows is
"no IPv6 router"any body know what is going on here or where where to look for more clues the next time I get around public wifi Oh the windoze washers and apple polishers don't seem to have any problems at all
View 4 Replies
View Related
Sep 16, 2010
I cant seam to find out how to get my card to work i cant find out how to install the driver or finding the wifi card on the system.
View 9 Replies
View Related
Apr 16, 2010
I have a brand new ASUS EEE PC 900HA with Ubuntu 9.10 installed on it. The wireless hasn't worked yet but the ethernet is fine. I've been browsing the forums for hours to find a fix but now I've installed/queried/removed so many things I'm totally confused.
lspci -v gives me this
Code:
01:00.0 Ethernet controller: Attansic Technology Corp. Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller (rev b0)
Subsystem: ASUSTeK Computer Inc. Device 8324
Flags: bus master, fast devsel, latency 0, IRQ 27
[code]....
View 9 Replies
View Related
May 12, 2011
get WIFI working on my Dell D600 with Ubuntu 11.04 freshly installed. I some limited sucched following the this post t=1621331 this got the card working but it was very very slow over 70% packet loss to the WIFIrouter. 1. Machine details Dell Latitude D6002 Wireless Broadband and Chip setlspci -nn | grep Broadcom - 02:03.0 Network controller [0280]: Broadcom Corporation BCM4309 802.11a/b/g [14e4:4324] (rev 02)3. Check interfaces
eth0 Link encap:Ethernet HWaddr 00:0b:db:e0:1c:5b
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[code]...
View 5 Replies
View Related
