Ubuntu Networking :: 10.10 Belkin F7D1101 Can't Connect To Network?
Feb 20, 2011
I'm using a Belkin F7D1101 USB adapter for my wireless internet, and I can't get the damn thing to connect. I've installed ndiswrapper, ndisutils, and ndisgtk, then used the latter to install the driver that came with the CD (though I'm sure I'm using the right one, I've tried all the included drivers with no success). The adapter itself is functioning fine, as I've used it on Windows XP with no issues. It's just not communicating with Ubuntu very well. My issue isn't that I can't get it to show up and search for a network (as I've seen on several other posts about this adapter), but that I can't get it to actually connect to my router. Using WEP 40/128, I enter the password, but after about a minute, I'm simply prompted for the password over and over. I've restarted several times, even installed 10.04 just because I had no idea what to try, and no dice.
View 2 Replies
ADVERTISEMENT
Mar 5, 2011
I'm having a slight problem with my new wireless card that I purchased. I installed the firmware and the like and it does work, my computer recognizes it and I can search through my available networks, only thing is though.I cannot connect to any of them. I'm fairly sure it's a problem with it obtaining an ip address though.because it does connect briefly and I read the status and it shows no IP address, but when I connect through wired internet all that information is available. I tried setting my network configuration to static and that didn't help at all. I'm only a week into Ubuntu so this is all still fairy confusing for me.
View 1 Replies
View Related
Jan 3, 2011
My ubuntu installation was running fine with the Belkin F7D1101 v1 after using this install method:[URL]..But, after allowing ubuntu to autoupdate many programs (don't remember which ones), the device stopped working. I checked all of the commands in the link above. They are all still functioning. dmesg throws no errors, but it terminates with
<code>ADDRCONF (NETDEV_UP): wlan0: link is not ready</code> Are there any network files which may have been overridden from autoupdate? iwconfig wlan0 shows "Access Point: Not-Associated" What output can I show you to help me find the problem?
View 1 Replies
View Related
Jun 23, 2010
I have a new belkin N1 router which I tested in somebody else's flat. It worked fine. When I got home I reset it by pushing a paperclip in the hole for 10+ seconds to erase this flat's internet connection settings (username and password and stuff). After this I plugged it the computer and tried to connect to it (wired connection) using 192.168.2.1 (this is correct for that router, it is not 192.168.0.1). But the browser says it is offline and cannot connect. The lights of the router cycle, the "modem router" light blinks continuously and the others briefly come on and go off again, every few seconds. I tried resetting it again, several times, leaving it off for a few hours, leaving it on for a few hours, etc.
View 2 Replies
View Related
Jun 20, 2011
I have just installed 11.04 alongside windows vista. I have been trying to connect my router but it keeps saying disconnected from network. I have ran all of the troubleshooting tips in ubuntu its self and everthing seems in order. is there any settings i need to change on my router or in ubuntu's edit connections programe? I managed to connect to the router once to upgrade from 10.10 to the 11.04 but even before upgrading to 11.04 i had problems connecting to the router.
View 6 Replies
View Related
May 4, 2010
I have been trying to get my Belkin FD8233-4v3 wireless-n usb adapter to work in Ubuntu since 8.04. It has worked with ndiswrapper under 32-bit (never the 64-bit) versions in the past, but has never been able to be configured directly. It uses the Ralink RT2870 chipset, but cannot seem to be configured using the drivers from the Ralink website.
With Ubuntu 10.04 64-Bit, everything has changed. I have high hopes that this adapter may finally work correctly and without ndiswrapper. As soon as I first booted 10.04, for the first time ever, Ubuntu recognized the IF automatically, reported my wireless router, allowed me to enter my 128-bit WEP hex code and tried to connect up. It is failing miserably, but it is making a valiant effort.
View 4 Replies
View Related
Jun 15, 2010
I was dual booting with XP and Jackalope using a Belkin N wireless USB. The install on Jackalope was simple, a plug and play type situation, plugged it in and it worked. A few days ago though, i wiped the whole computer and installed Lynx. To my dismay, even though Lynx sees the wireless, sees the available signals, lets me input my password... it fails to connect. It just spins and spins and eventually asks for my password again...
I'm still pretty new to Ubuntu, and Linux in general. I updated, and pretty sure i retrieved 3rd party drivers for the video card properly (using a cable connection), but thats pretty close to where my "expertise" ends.
View 9 Replies
View Related
Sep 22, 2010
I am using the Belkin wireless g usb adapter f5d7050 v1000 or at least that is what ubuntu says when I lsusb.
Code:
ceegee@Valar1:~$ lsusb
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 019: ID 050d:7050 Belkin Components F5D7050 ver 1000 WiFi
[code]....
View 2 Replies
View Related
Mar 9, 2011
I've just literally gone out this morning and bought the Belkin N300 Dual Band USB for my Deskstation running Maverick Meerkat. At first i put the stick in and nothing happened. So i went to System>admin>Windows wireless drivers and clicked on there. I put the CD in the drive that came with the dongle and found the drivers folder on the disk. I then installed the .inf file in the XP folder. It connected straight away as easy as that.
I'm really frustrated though as it loses conectivity and then asks me for my WAP password on connection, but then doesn't seem to connect. I unplug the dongle and then hit connect again and it connects.
If i use the same dongle on XP i have no problems what so ever, so i know its not a signal strength issue.
View 8 Replies
View Related
Apr 13, 2011
I recently installed the latest and greatest Lubuntu 64 bit, because I like lxde and I am planning a system migration. (I am really starting to not like windows 7.) I have some linux experience. I wouldn't say I am awesome at it, but I am comfortable trying anything.
Example: I have used CENTOS 5.6 to make a linux machine server as a glorified router, with asterisks, SIP, SSH server, x windows, GNome, VNC, and a user authentication system. and get this I walked somebody through setting this up over the phone. I reopened the root account (I honestly got tired of typing sudo every other command is the only reason why I opened it.) I plan on closing it after we are done.
lsusb lists the wireless adaptor
Wireless Card Link
[[URL]
I have the driver CD. I installed ndiswrapper.I copied the files from my driver cd to my <home> Directory. Then installed the Windows XP version of the drivers using ndiswrapper -l <driver>. I then made ndiswrapper force the driver to the vendor ID of the wireless card. Using ndiswrapper -a <vendor ID> <Driver>(I did this last night and the vendor ID escapes me. I am at work now.)I finally ran depmod -a and modprobe ndiswrapperI goto the windows wireless driver application, and it shows the driver as loaded and the hardware as found.
However, it still does not list a wireless device in the network manager to where I can connect to my wireless. iwconfig does not show any wireless LAN, but it is still listed in lsusb. Also, the light that shows activity on the wireless device does not light up or blink at all. I have about 6 usb ports on my desktop and have tried everyone. The wireless card also works in Windows 7 64-bit On a strange side note. I do have internet access through LAN, (My laptop is atm a glorified wireless card .)
View 4 Replies
View Related
May 14, 2010
Code:
*-network
description: Ethernet interface
product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
[Code].....
I've read around blacklisting but I'm not sure on what I should be blacklisting really.
View 9 Replies
View Related
Feb 3, 2010
I have a Belkin Enhanced Wireless USB Network Adapter Model # F6D4050 v2. The drivers are for windows but the windows wireless drivers app doesnt work. I see a tutorial for a linksys that appears to have the same chipset, but I am not sure if any of the steps need to be modified, also my kernel is a bit different. Here is my kernel:
[code]...
View 1 Replies
View Related
Feb 15, 2010
Am all of 2 days old on Opensuse 11.0 having just installed it on my old PC. All my experience has been with XP/Vista and Macs and it took some courage to finally try this out. My Belkin F5D9050 wireless(g+ MIMO) usb network card is recognised in yast but does not connect to the internet. On reading through forums I understand that this adaptor uses RAlinks RT73 chipset and support for should already be available in the OS. Is this correct ? If not, where do I get the driver for this and how do I install this. As per the Belkin site, Opensuse driver support isnt listed. Am struggling due to the unfamiliar environment and am not aware of terminal commands.
View 1 Replies
View Related
Jan 1, 2011
I am new to ubuntu and am trying to connect to the Internet with a usb wireless from belkin. Attached is the wireless_setup.txt.
View 2 Replies
View Related
Aug 8, 2011
I can connect to the internet through wifi, but I cannot connect to anything on my network. I have a printer and a NAS, so I would really like for this to work again. I have a dell laptop with a Broadcom card.
View 9 Replies
View Related
Jun 12, 2010
I'm pretty new to Linux, but have had a bit of functional tutoring. i'm triple booting my old Dimension 8400. Have been running with Jackalope and XP for some time now and wanted to install Lynx and get a good handle on it before i completely wipe my other machine (Win7/Jackalope) and install it there.
Installed Lynx from a USB stick and all seems well, it recognises the UBS wireless and all available connections but just sits and spins on the password login and never connects...hmmm. I have tried all possible combinations of rebooting with the USB connected/disconnected/connecting after... to no avail.
The wireless seems to "work out of the box" just as seamlessly as it did for Jackalope, all the steps are similar, it just never connects.
View 6 Replies
View Related
Mar 11, 2011
I'm looking at buying one of the above cards, and was wondering if anyone knew if they worked in master mode (e.g. as an access point). According to the Aircrack-ng site, they support packet injection and monitor mode. Is master mode support solely up to the driver used with the card, or does the card have to physically support it?
View 2 Replies
View Related
Jul 1, 2010
I recently fixed an annoying problem and I thought it would be nice to share my solution here. The problem was that after a cycle of suspend/resume, Network Manager would only auto-connect to the same network as it was previously connected to. So, for example, if I suspended my laptop at home, and then I went to school and resumed it, it would try to connect to the home network, and then just give up. It would not connect to the school network unless I explicitly told it to.irst, I'll describe the fix. If you're having this problem, you can this. Copy the following:
Code:
#!/bin/sh
case "$1" in
[code]....
View 5 Replies
View Related
Jun 14, 2010
I have used ubuntu in the past but had a lot of hardware issues with it and unfortunately moved back to windows (( BUT i have tried Ubuntu again and all seems to work great except wifi My wifi connection is sort of working because when i run SUDO IWLIST SCAN it does pull up all available networks. But in the network manager icon on the panel i left click but i see no networks and can't connect to anything. I WOULD LOVE TO keep Ubuntu and use it permanently but I must get wifi working or else this won't be possible.
View 4 Replies
View Related
Jul 10, 2010
I recently put Linux on a Thinkpad T40 I got. The wireless card works out of the box--I can see nearby networks. However, I can't connect to mine. network-manager would try (spin spin spin), fail, ask for the password, and then go back to the beginning and repeat indefinitely. This happened to me on a different computer, and on that one all I had to do was use wicd instead of network-manager. So I installed wicd, but it's not working either--it hangs at "Obtaining IP address".
I've found many, many threads with people who had the same problem, but none of their fixed worked for me.
I also tried to get wifi going manually, using this guide, but that didn't work.
View 3 Replies
View Related
Feb 3, 2011
Tomorrow I'll delete Ubuntu and install Opensuse. I use 100% linux system PC, with no windows and I'm interested to know if someone have found a way to use Belkin Network USB Hub (Belkin : Network USB Hub). Belkin doesn't provide linux drivers for this network hub.I've tried on Ubuntu to install the windows driver with Wine with no success. Maybe in Opensuse It'll be the same, but if anyone have got a good experience with this hardware,
View 2 Replies
View Related
Aug 26, 2010
I am thinking about buying Belkin's Network USB Hub so that I can plugin usb devices and share it over network(Debian based computers). The device's website and spec can be found at: [URL]. Is this device supported by Debian Etch or Lenny? Did anyone used it on any versions of Debian
where it worked? Is there a Linux driver for it?
View 1 Replies
View Related
Jan 3, 2011
i have ubuntu 10.04 i believe and i cant connect to the intenret i guess its not detecting my wireless adapter. i cant try ethernet cord which prolly would work because i cant move pc to another room....is there any fix for this? i googled linux drivers but i cant find any...i do have the cd that came with the adapter.
View 1 Replies
View Related
Sep 6, 2011
I have gotten this to work on Xubuntu here: [SOLVED] Ndiswrapper? Does it work? - Ubuntu Forums.I think it would use the same software/firmware? I am using OpenSUSE 11.4 LXDE derivative.
View 4 Replies
View Related
Dec 23, 2009
Cannot Connect to a wireless network using a USB Belkin 802.11g Model F5D7050: Setting up a new pc is running opensuse 11.2 (i586) KDE 4.3.1
Question1) The HCL shows a version, how do I find what version i have?
Question2) Why is rt73.bin not being loaded? I ask this because the file is located in Root/lib/firmware
Question3) Why is Configure Desktop > Network Manager > Wifi is blanked out as if doesnt exist?
Question 4) when using YAST > Network Settings > Initially under wireless network card configuration I can scan the area and find networks successfully (I got 2, one as a wifii hotspot from my pda cell phone, the other is the standard wireless network for laptops and such).... but if i use kinternet >wlan0 > wireless connection, nothing will be found! I did a search on the /var/bootlog msg for "switch" and "radio", for radio I found the following:
<6>[ 9.108858] Registered led device: rt73usb-phy1::radio
<6>[ 9.108884] Registered led device: rt73usb-phy1::assoc
<6>[ 9.108909] Registered led device: rt73usb-phy1::quality
<6>[ 9.109386] usbcore: registered new interface driver rt73usb
[Code].....
View 1 Replies
View Related
Nov 25, 2010
I have recently installed openSUSE 11.3 I have a Belkin G Wireless Network Adaptor
Model: F5D7050
FCC ID: K7SF5D7050E
Linux doesn't seem to recognise this device at all. I had a look online from another PC for drivers. and they are provided by Belkin themselfs but only for Windows XP/Vista.Is it possible to get this working on openSUSE. I previously used this very same adaptor on an Unbuntu 10.2 PC and it worked with no problems at all.
View 1 Replies
View Related
Mar 11, 2010
I have a Belkin Wireless G USB Network Adapter but I cant get on the internet with it.The laptop is running Damn Small Linux.Heres what is going on and the code I typed:
ndiswrapper -i rt73.INF
ndiswrapper -l
modprobe ndiswrapper
iwconfig
ndiswrapper says the driver and hardware are present but iwconfig and ifconfig don't say anything.The wireless adapter works fine in windows 2000 and windows xp with the same driver.The green LED on the wireless adapter never flashes like it is supposed to.
View 3 Replies
View Related
Nov 21, 2008
I'm unable to connect to a particular home wireless network under Fedora 9, although I can connect to it using WinXP on the same machine. My Fedora installation is able to connect to my college's unsecured wireless network, so it's not a driver issue I think.It seems to be an authorisation issue, as I'll describe below, but there's one other thing that's bothering me. The SSID for the network I have problems with is for some reason not listed in Network Manager's drop-down list, nor is it in the output of iwlist wlan0 scan. But I'm pretty sure it's not a "hidden" network - I don't know exactly how those work, but I helped the owner of the wifi network in setting it up, and don't remember doing anything that would make it hidden. As far as I can remember, Windows found the network automatically without having to be told the SSID. What's the best way to confirm whether it's a hidden network or not?
Anyway, I try to connect by selecting connect to other wireless network in Network Manager, and entering the SSID. As far as I can tell from the error messages below, the machine does contact the network and attempt to connect, but I'm not authorising myself properly. That may be a completely wrong diagnosis, but hopefully someone can see from the below info whether it's correct or not.I'm not sure which option to use for "Wireless Security": at the time we set up the network, it gave us a Hex WEP key of 26 characters, which is 104 bits. But none of the options in Network Manager's list match that. Here are the options it has, and the error message I get with each one:None - if I select this, it fails to connect, with no error message.
WEP 128-bit passphrase - if I select this and attempt to use my 26-character WEP key, it brings up a new dialog, saying "Passwords or encryption keys are required to access the wireless network [SSID]." It has a drop-down box labelled "Wireless Security", but this time the only option is "None", and the connect button is disabled, I can only click cancel.
WEP 40/128-bit hex - as above.
WEP 40/128-bit ASCII - The connect button is disabled when I try to use the WEP key, as the string is too long. Despite the fact that it says 40/128-bit, it actually accepts 5 and 13-character strings (40 or 104-bit). Since I've got a 104-bit hex key, I tried converting it to ASCII, but it consists of mostly unprintable characters, so I'm not sure there's any way to actually enter it into the textfield. I might have done something wrong here, so I've put my code below to see if anyone can point out a mistake.
LEAP - requires a username, not applicable here I think. Windows doesn't need one, and we don't have one from when we set the network up.Dynamic WEP (802.1x) - requires username, private key and various other things, all N/A WPA & WPA2 Personal - Brings up a dialog with the same text as for "128-bit passphrase", but this time "WPA & WPA2 Personal" is the only option in the drop-down list, instead of "None". It asks for a password, so I just enter the hex key again - now it asks for the password for the Gnome Default Keyring, which I don't think I've ever set up. Don't know if I can go any further with that, but my understanding is that since we were given a WEP key when we set up the network, WPA will be N/A.WPA & WPA2 Enterprise - as Dynamic WEP. N/A.Hopefully that's enough info that someone can help diagnose the problem. Some of the behaviour of Network Manager described above doesn't make sense to me, and I'm wondering if it's buggy.
View 14 Replies
View Related
May 26, 2010
configure my Belkin Wireless USB adapter(F7D2101)? I attached the adapter and rebooted the system. I used the hardware info and it is listed but no drivers.
View 1 Replies
View Related
Aug 3, 2010
Ok, so I am needing some drivers and I've been googling like hell to find em, however, I can never seem to find any. My adapter model is F6D6050v1.
PS: when I try sudo ndisgtk it comes up with command not found.
View 1 Replies
View Related
