I installed UBUNTU 10.10 alongside windows 7. Now the problem is: If i boot into UBUNTU first, ethernet does not work. But it works if i boot windows first and restart back into UBUNTU. Which means i have to boot windows first to make ethernet work on UBUNTU every time i start my PC.
View 9 Replies
I have 2 (some future machines will have 4) ethernet ports. I want to have them configured such that if any gets unplugged, as long as at least one of them is plugged in, it can reach the network (even if via a different IP address), and it can be reached (at least when trying a working IP address). I tried this for /etc/network/interfaces:
Code:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
[Code]...
I'm currently running Fedora 13, after I updated the kernel to 2.6.34, I have to run (as a superuser) "service NetworkManager start" in order to start my network manager, is there are way I can run this on startup?
Also my ethernet connection seems to only work when I restart/boot up my computer, when I wake my computer up from being asleep, the ethernet stops working.
I made a Ubuntu server and it is pretty cool. I had a windows computer that I could copy and paste files to and from over the network. What you did is just find it in My Network and the files were available there. How do I make Ubuntu or Samba act like that?
View 2 Replies View RelatedIm trying to make an ubuntu server box my entrypoint to my networking. Meaning itll function as a server, a firewall, and a gateway. so i already installed dhcp3 and a dns server.
I have 2 ethernet cards in it. So now i wonder, should i the second card into a router's modem/wan port and make the router a switch? or should i plug it into one of the routers lan ports?
I absolutely love Lubuntu on VirtualBox. I installed it to my Compaq Mini CQ-10 without issue. However, there are no drivers for the Wireless or the NIC. Ok, so I go to Broadcom and download the drivers. But, when I try to install with the Makefile, Terminal tells me that make is not installed! Now, how do I install my drivers without make?
View 4 Replies View RelatedI just fresh installed Fedora 11, and tried to connect via ethernet. I connected the cable and connection was started (in the network managed the two gray circled turned green) but then instead of connecting me the connection was aborted. I am behind a router if it helps and made sure eth0 is enabled. PS this is the output of "service network start":
Quote:
[root@Gal-PC subsys]# service network start
Bringing up loopback interface: [ OK ]
Bringing up interface eth0:
[code]......
i was instelling ubuntu 8.10 on my laptop type HP (nx6110) but the Ethernet and the wireless are not work. i was used the nm-tool on terminal the code is
zaid@zaid-laptop:~$ nm-tool
NetworkManager Tool
State: disconnected
- Device: eth0 ----------------------------------------------------------------
Type: Wired
[Code]....
I booted ubuntu and the included drivers worked beautifully for my Atheros AR8131 PCI Ethernet card on my laptop. I have an OSX Snow Leopard dual boot setup and my Ethernet card does not work. I was wondering if, because OSX is loosely linux based, the network drivers could somehow be loaded into my Snow Leopard install.
View 1 Replies View RelatedI have an Asrock A330GC, with onboard ethernet, and an Engenius PCI card for wifi.I installed ubuntu server 9.10 no problems, and it picked up my ethernet in the installation with no difficulties.I couldn't get 9.10 to do what i wanted, so I tried installing 8.4 instead. This however didn't pick up any of the drivers, so i couldn't get online.So i reinstalled 9.10, only to find that no couldn't find network in the installation.Absolutely NOTHING has changed, the ethernet cable still plugged in, and if i plug same cable into my laptop, it works fine.Any ideas people?ifconfig doesn't mention any eth0, just lo, with an ip of 127.0.0.1 and amask of 255.0.0.0 which i'm fairly certain means its dead
View 1 Replies View Relatedlaptop: averatec 6200 series
ethernet driver: SiS 900
wirless lan driver: rt2500
I got 10.04 installed and running pretty well.I cant get the wired ethernet to work but the wireless works. i did the the command line
[Code]...
also, dont know if i matters but ive got 8mbps/1.5mbps cable (motorala surfboard cable modem) and a linksys wrt54g wireless router.
I have a HP Mini running Ubuntu Desktop 10.04, and I cannot get a wired connection to work. My network card is "Broadcom Corporation BCM4312 802.11b/g (rev 01)", and I have the restricted drivers for the card installed. Wireless works fine, though.
My /etc/network/interfaces:
I have this tread, for a ASIX USB ethernet adapter. Still don't work.Tody i bought a Davicom DM9601 USB 10/100 EthernetI read here about this work out of the box, since 2.6.21 kernel. I have Linux Mint (Ubuntu 10.10) with 2.6.35-x kernol version; lsusb detect it; dmesg, detect it; at configure, automaticly get the MAC address, but just didn't work; with ping command, i get network is unreachable.
View 1 Replies View RelatedI have an old sony vaio laptop, and it has an intel 82801cam ethernet device and it refuses to work when I plug it in to an ethernet adapter. Im thinking it is a driver issues but whenever I list my hardware devices in terminal with lshw it seems to see that device despite that
View 1 Replies View RelatedThe GUI for network configuration of Fedora is marvellous such that the configuration is almost fool-proof. But how can I make the connection by hand in the command line mode? It goes okay except the very last step. When I disconnect the eth0 interface from the right-hand side of the desktop GUI, I tested how to bring it back by command line but I failed. When disconnected, the ifconfig still shows the eth0 interface, with just the ip address portion changed.
I tried "ifconfig eth0 192.168.1.xx" to give it an ip address but the connection is still down even if the ifconfig shows an ip address for the eth0 interface. Then I tried "/etc/init.d/network restart" and "ifup eth0" and also "route add defaut gw 192.168.1.1" but none of these could accomplish the same work as a single click on the GUI to connect. I am very curious about how to do it in the terminal.
Tell me how to configure my Ethernet card to work. My pc only works wirelessly. I don't know what kind of Ethernet card is installed. I have Ubuntu 10.4 on a dell pc 1ghz, 20ghd, 512mb.
View 2 Replies View RelatedI'm running Ubuntu 9.0.4 with an Intel PRO/100 VE Network Connection. I have been trying for a couple weeks now different techniques to get my wired ethernet connection working properly. I have a seeming common issue with my e100 driver dropping connection and having hard time picking it back up sometimes. I want to purchase a relatively inexpensive Ethernet card whose generic Linux driver actually operates it CORRECTLY, open up comp and put it in, and update to 9.10. Any list of Ethernet cards that are know to work flawlessly on Ubuntu, or at least tell me which card YOU are using that works perfect without having to write code, install wrapper programs, etc...?
View 8 Replies View RelatedI have installed Ubuntu 11.04 using Wubi through Windows 7. It seems to be working but it will not connect to my wired internet connection. It tells me there is no wired connection, when there is. I used sysinfo and its not showing any network adapter or controller. I have a board with nvidia nforce go 430, could it be a driver issue. It works fine in windows though. Tried using a wireless adapter and all is working. But why doesn't the wired ethernet connection work.
View 9 Replies View RelatedI have had some problems with a SATA DVD drive under installation of Slackware 12.2, [URL] So i tried 13.1 instead. But now the ethernet card is not working Its a VIA Rhine card, and it was recognized just fine under 12.2 The following command did nothing: Code: ifconfig eth0 up I am getting no errors. I have also tried using netconfig, no luck there either.
View 3 Replies View RelatedI'm a new user of Ubuntu, so i'm not that familiar with this OS. My wireless network is detected but when I'm entering my 128 bits WEP key, it doesn't connect at all. I have no clue where to start troubleshooting.
Here's some of my specs if that's of any help:
Computer is a Sony Vaio laptop model VGN-SZ370P
My wireless card is from Intel Corporation 82801G (ICH7 Family) USB UHCI Controller
The ethernet cable connection used to work before, but I fooled around with some commands and now seems to be disabled...
I have a Zotac Ionitx A-U. I can't get it to establish an internet connection with the wired ethernet within Ubuntu. The chip is detected, but trying to bring up the connection stalls out at trying to obtain a DHCP lease, like this:
DHCP DISCOVER ...
DHCP DISCOVER ...
No DHCPOFFERS received
Specs:
Ionitx A-U
Ubuntu 10.04 x64 kernel 2.6.32-22 (also didn't work in 9.10)
[Code]...
By upgrading to latest kernel(2.6.31-22) the card was recognized but it still doesn't quite work. I'm not that good at this but I'll paste some stuff that I think is related to solving a problem such as this.
[code]...
I have a Dell WLAN 1397 Half Minicard, 802.11 b/g card in my laptop, and I can't seem to get ubuntu to work with it. I tried this method:
1. Synaptic Pack Manager
2. Check "Install from Boot Disc"
3. Reload
4. Install and apply bcmwl-kernel-source
5. Reboot
This didn't work for me, so I tried entering sudo apt-get install bcmwl-kernel-source and that also didn't work. Another thing I tried is formatting my Ubuntu partition and reinstalling, and retrying both of those methods. The ethernet port does work, however.
I wanted to test 10.04 and downloaded Wubi to do so. Normal setup, it automatically picked the 64-bit version. After booting into Wubi, installing my ATI drivers and restarting it did no longer connect to my ethernet. A few reboots didn't help so I went back to Windows for troubleshooting.
However now Windows doesn't connect to the ethernet either. It's plain dead, Windows doesn't find any connections and the modem doesn't light the Ethernet cable LED. The modem itself works fine with wireless devices. I have now tried everything including uninstalling Ubuntu, system restore, driver rollback, driver update, BIOS default settings, a different cable, a different modem etc.
This is a 64-bit specific issue because I tested the 32-bit version of Wubi 10.04 a few months ago without problems.
Windows 7 x64
Wubi 10.04 x64
Gigabyte P55-UD3 with onboard Realtek RTL8111D LAN.
I'd like to get out of this without Ubuntu effectively having broken my hardware and my trust in it.
I've recently bought a recycled computer for my office. The plan was to get an old cheap computer and use it to write LaTex documents but nothing else. However, I can't seem to get the thing to connect to the internet. I'm on a University network which has a funny setup but I don't think that's the problem.So here's the deal. I have tried this with 9.04, 10.04 and 10.10 and it hasn't worked. The computer recognizes the ethernet cable. If I issue the command "sudo mii-tool eth0" and get back "eth0: negotiated 100baseTx-FD, link ok". However, click on the networking logo on the top right, and click auto eth0, it tries to connect for about 30 seconds, then gives up. Unfortunately I'm pretty clueless when it comes to networking so I have no idea what to do to try to fix this.
View 8 Replies View RelatedI changed a mainboard so the network card is RTL8111/8168B Gigabit now. By "ifconfig -a", there is only io, no eth0.
I got a driver r8168.ko from: [URL]
After I insert the r8168.ko, there is eth0. Run "/etc/init.d/network restart", it reports "Determing IP information for eth0... failed; no link present, Check Cable", and I noticed the lights of network card and runter are all off. I can use "ifconfig eth0" now but it cannot connect to other machine.
It's Gigabit card and my runter is 10/100M. I tried "#insmod r8168 speed=100 duplex=1 autoneg=1" and "#insmod r8168 speed=100 duplex=0 autoneg=1", it can not get IP by DHCP either. I also build the .ko from Realteck source code, the behavior is the same.
if I need to do other configurations?
My CentOS is CentOS5, 2.6.18-8.el5 #1 SMP.
== BEGIN uname -rmi ==
2.6.18-8.el5 i686 i386
== END uname -rmi ==
== BEGIN rpm -q centos-release ==
[Code].....
I have installed Ubuntu 9.04
uname -r
2.6.28-11-generic
Checked cable/network with 386Box running Ubuntu 8.04 all OK. Could not get Realtek 8168 on mother board to work on Gigabyte H55M-S2H motherboard. I tried to install r8168 driver but no luck ... so I bought another Linux compatible card which turned out to be a RTL8139c (eth1) and the driver I am using on this is card is 8139too.
[Code]....
My preference would be to get the motherboard ethernet working but perhaps the card may be easier to get working. Anyway after searching the net for ideas and trying different things I've just about given up. I have reinstalled Ubuntu today so eth0 is back to using the r8169 driver. I'm no expert so my attempts at following other recipies have so far failed. From what I have read the 8139too driver should have worked with the RTL8139C chip so I have run out of ideas. I must be doing something wrong.
So here is the deal, I have my wifes computer set up to dual-boot Ubuntu 9.10 and Windows 7. She uses a HP G60-445DX laptop, and something very funky is going on.
1. I first installed Windows 7, and it boots fine multiple times with no problem.
2. Next, I install Ubuntu 9.10. After installation is finished, I select reboot, and choose Windows 7. It boots fine.
3. Then, I reboot into the newly installed Ubuntu for the first time, get to the desktop, and reboot.
4. Now when I select to boot Windows 7, it gets about half-way, and suddenly reboots the computer.
I've troubleshooted this thing for days on end trying to isolate exactly what is causing Windows 7 not to boot. After reinstalling Windows 7 again, it once again boots fine, even after I use the live CD to restore Grub 2. It's only after I boot the fully installed Ubuntu 9.10 that her Windows 7 install starts acting weird. All I can narrow it down to is that after I boot into Ubuntu for the first time (after an install), Windows 7 no longer boots properly.
My laptop was working fine on wireless till the userinterface changed and it defaulted to ethernet and now it won't let me go back on wireless How do i disable ethernet?
View 4 Replies View RelatedHow to make Windows Boot Manager automatically open GNU GRUB and then with GNU GRUB automatically boot Linux Ubuntu 11.04.
View 1 Replies View Related
