Ubuntu :: NVIDIA Quadro NVS 450 - Blank Screen
Oct 5, 2010
I have just bought a Dell Optiplex 960 with a NVIDIA Quadro NVS 450. Everything works out of the box with the 10.04.1 Live CD. It suggests to install and activate NVIDIA proprietary drivers, but you need to restart the machine afterwards. The problem is that, after that, all what you get is a blank screen, with not even a cursor. The same happens when you install Lucid: blank screen with no cursor. Ctrl+F1 does not show anything, but Ctrl+Alt+Prnt Scrn+REISUB works and the PC is reset. In the var directory the logs show that the NVIDIA module is not loaded.
View 2 Replies
ADVERTISEMENT
Oct 5, 2010
I have just bought a Dell Optiplex 960 with a NVIDIA Quadro NVS 450. Everything works out of the box with the 10.04.1 Live CD. It suggests to install and activate NVIDIA proprietary drivers, but you need to restart the machine afterwards.The problem is that, after that, all what you get is a blank screen, with not even a cursor.The same happens when you install Lucid: blank screen with no cursor.
Ctrl+F1 does not show anything, but Ctrl+Alt+Prnt Scrn+REISUB works and the PC is reset.In the var directory the logs show that the NVIDIA module is not loaded.
View 2 Replies
View Related
Jul 28, 2010
I just got done installing Ubuntu on a new harddrive and set it up to dual boot with grub loader. However, when I boot into Ubuntu, the screen goes black. I can however login (blind) by hitting enter and typing password. The login sound goes and it logs in, however, the screen stays black. I am running a NVIDIA Quadro NVS 295 Video Card.
View 9 Replies
View Related
Apr 25, 2010
I did a fresh install of 8.04 alternate disk with LVM then updraded to 10.04 (due to lack of any spare CDs around).
Everything was working fine but wanted to try to get the nvidia-173 drivers installed (I have an old FX5200). Can't start into X now as my plasma says mode unsupported.
At one point I managed to boot into recovery mode then root terminal and removed all nvidia packages and reinstalled nvidia-173 only and followed the instructions listed on the 10.04 release candidate page. Still stuck with the unsupported modes error on my TV though. I have a 720p plasma display (1366x76, I usually run 1280x768 without issues. I'm guessing it is the refresh rate set in the new xorg.conf that is throwing me off, how to adjust this?
An issue that's complicating things however is that when I try to boot into recovery mode I get an error stating 'pcspkr' driver already registered, aborting... then it hangs there until I ctrl-alt-delete and force a restart. This is preventing me from getting to the point where I can select a a root terminal to try to fix my errors.
I have used 8.04 exclusively for a few years and wanted to try something new (still not all that adept at linux setup).
EDIT: I managed to get to root again and just removed the xorg.conf file and that seems to work somewhat. Except now I can't boot as I get a looping mountall: Plymouth command failed that hangs up the process.
View 1 Replies
View Related
Jan 28, 2010
My F11 system display goes blank after some time of inactivity and I cannot see how to disable it. It does not appear to t eht screen savers (all turned off). I have an NVIDIA card,, is it in the card?
View 8 Replies
View Related
Oct 7, 2010
I have installed Ubuntu Maverick 10.10 RC in my PC, everything works fine, but after install Nvidia proprietary Graphics driver it boot up on a blank screen (I can hear the login sounds, etc) but screen is absolutely black.
I try to login in recovery mode and check if something is wrong but nothing happens (even adding noveau driver to a blacklist (editing grub)) Now I have re installed Ubuntu 10.04.1 and works fine but I would like to install the 10.10 version, since I have this inconvenience, I cant do it.
My graphic card: Nvidia Gforce 8400GS 256MB Pci Express
View 9 Replies
View Related
Jan 11, 2011
I just built myself an new workstation and now only 2 of 3 monitors are working. I built the nvidia driver by downloading it and installing with ./Nvidia...Before when I ran nvidia-settings I saw two GPUs listed but now I only see one. Xorg Config (Not sure how I ended up with 3 devices in there):
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:39 PDT 2010
Section "ServerLayout"
# Removed Option "Xinerama" "1"
[code]...
View 1 Replies
View Related
Jan 24, 2011
Like the title says, I have the Quadro NVS 135M in my Dell D630. It's working (well, besides the startup screen issue - Plymoth... not a fan!), but when I watch a movie the image ?flickers? annoyingly. This is something I have never experienced before, with allegedly ?inferior? video cards. It's odd though, isn't it - better video card, inferior output!?!
View 1 Replies
View Related
Oct 22, 2010
Running 2.6.33.3-85.fc13.i686 and just purchased a AGP 7600GT 512 video card. Searched around and found:I did the rpm, yum, sed, mv & dracut as directed. Then I rebooted. When it starts up (all the normal bios messages) and then I 1/2" bar across the bottom of the screen with Fedora 13 on the right end and .... nothing. Just sits there. I've used my Live-13 disk and tried to reverse the procedure but I'm starting to think it's the video drivers.
View 4 Replies
View Related
Mar 15, 2010
I installed OpenSuse Gnome version 64 bit on a HP laptop DV7 Intel Dual Core with nVidia 9600 GM cardAll went well, until after I had installed the nVidia drivers from this page: NVIDIA drivers - openSUSEI selected the Geforce 1-click install and Yast went on to installl all the packages (a lot of 32-bit),took about half an hour.I logged out/in, and could work as normal, until I rebooted. Maybe I waited not long enough (5 minutes), but the screen was blank, then I gave up.Anyone has an explanation. I can always re-install everything, but then what went wrong with the nVidia package
View 9 Replies
View Related
Mar 8, 2011
I'm installing 10.10 on a desktop with Nvidia 6150 that needs nomodeset on boot or i get the blank screen upon boot. I had to force the live CD to nomodeset when booting from the CD. I was finally able to install, but upon the first boot from the hard drive I'm getting the blank screen again. How do I boot with nomodeset and get to my installed ubuntu. Once I get there i can edit my grub settings.
View 3 Replies
View Related
Apr 2, 2010
I come here every two or three years, when I have some troubles with my graphic card. Indeed, once again. Since last Tuesday, I experience some system freeze. Since yesterday, I must run on low graphic mode. As there has not been any X.org or driver update, I suspect that my graphic card is running down. But I do not know how to diagnose this.
My configuration:
-- Dell Latitude D820 laptop;
-- processor Intel Core 2 Duo T7200 (2.0GHz 667MHz FSB);
-- bi-canal 2x1024Mo DDR2-SDRAM 533MHz memory;
-- graphic card NVIDIA Quadro NVS 110M 256MB;
-- 15.4" WSXGGA+ (1680 x 1050) LCD screen;
-- 100Go SATA (7200 TPM)) hard-drive;
-- 8x DVD +/- RW burner;
-- battery 9 cells 85 WHr LI-ION;
-- Bluetooth card for Latitude;
-- Intel PRO/Wireless 3945 802.11a/g;
-- Ubuntu Linux 9.04 Jaunty Jackalope desktop 64 bits real-time kernel.
Some commands results:
Code:
$ lspci | grep -i vga
01:00.0 VGA compatible controller: nVidia Corporation G72M [Quadro NVS 110M/GeForce Go 7300] (rev a1) .....
View 4 Replies
View Related
May 4, 2010
Trying to install 64bit onto Dell T3500 with NVidia Quadro NVS 295. Live Cd works and Install completes. When I boot I get BIOS and Disk info then boot switches to flashing cursor after disk read and then Monitor goes into sleep mode.
View 6 Replies
View Related
Mar 15, 2010
I ran the latest updates this week (including the new kernel and the new kmod-nvidia update) and I got a blank screen when I rebooted. (I get the Fedora bar across the bottom of the screen, then after that the screen goes blank) I assume this is when the xorg server is trying to start..
I went into single user mode , backed up and then removed the xorg.conf file but still got a blank screen upon reboot.
I rebooted into single user mode, copied the /var/log/Xorg.0.log file to a safe location, and then restored the system back to its original state.
I've since rsync'd my system back to where it was before the update.
Here's my Xorg.0.log file:
View 3 Replies
View Related
Aug 25, 2011
I've posted this to the fedora mailing list with no response, my apologies if it's been addressed here...
I have an IBM Thinkpad with an Nvidia card ( nVidia Corporation GT218 [NVS 3100M] (rev a2) )
I currently have the nouveau driver black listed in my grub.conf setup: rhgb quiet nouveau.modeset=0 rdblacklist=nouveau
I did the update which installed/updated the following:
---> Package kernel.i686 0:2.6.35.14-95.fc14 set to be installed
---> Package kernel-devel.i686 0:2.6.35.14-95.fc14 set to be installed
---> Package kernel-headers.i686 0:2.6.35.14-95.fc14 set to be updated
---> Package kmod-nvidia.i686 1:280.13-2.fc14 set to be updated
However when I reboot the system boots to a blank screen, and even the previous kernel boots to a blank screen. I tried installing akmod-nvidia but get the same results
I've restored the system back to before the update for now..
View 1 Replies
View Related
Jul 16, 2010
I have just performed an upgrade from OpenSUSE 11.2 to 11.3. My Machine is a Lenovo W701DS laptop which uses an NVIDIA FX3800M graphics card. The system was working fine under 11.2 before the upgrade.
After upgrading to 11.3 the splash screen after GRUB comes up for about 1 second before the screen goes blank. After about 5 mins I am able to SSH to the Laptop and access the system. Doing this I created an xorg file using "X -configure" and copied the new file to the /etc/X11 directory and renamed to xorg.conf.
If I SSH to the laptop change run levels to init 3 then init 5 the Gnome comes up and I have graphics the system works However I am unable to access the text consoles using alt+f1, f2 etc. If I restart the system it is back to the blank screen.
I have attempted to install the NVIDIA drivers however the installation fails due to an error with gcc or kernel source versions. Error log reports that the kernel was complied using a different version of gcc.
View 3 Replies
View Related
May 28, 2010
i did yum -y install akmod-nvidia and then type xconfig-nvidia on the terminal,and after logging off i confront with a blank screen,so i remove akomd-nvidia [yum remove akomd-nvidia] and also yum erase xorg-x11-drv-nouveau [yum erase xorg-x11-drv-nouveau]but still no gui,i think i should install:
yum install kmod-nvidia
xorg-x11-drv-nvidia-libs.i686
xorg-x11-drv-nvidia-libs.x86_64 [but i didn't]
so how can i have my gui back?
View 5 Replies
View Related
Jun 9, 2010
Just upgraded my system from 13.0 to 13.1 Most things went pretty smoothly, but I tried 'startx' before the post-upgrade/config reboot and the system hung - "time to upgrade my video drivers", I thought. Upgraded to Nvidia 195.36.15*. X works perfectly, and a modprobe shows the 'nvidia' module loaded. So far so good.
However, when I try to use any vesa modes in lilo, I get a blank screen after the BIOS check and the system hangs - even toggling numlock on or off won't work... So I can only boot up in text mode. This makes me unhappy, partially because I like penguins, but also because it is an absolute insult to my new (old) monitor. I thought this could be to do with the nouveau conflicts reported by -current users some days ago, but the respective blacklist file is present so I'm stuck as to what to do... *I've tried 195.36.15, 195.36.24 and the latest 2xx beta drivers. All exhibit the same behaviour.
EDIT - forgot to post my video card specs. It's an 8500gt w/ 256mb, 128-bit DDR3.
View 16 Replies
View Related
Oct 31, 2010
I'm new to linux and trying to install the driver for Nvidia quardo fx 380 lp in redhat 5.4.From the Nvidia site I got the driver for this card to be NVIDIA-Linux-x86-260.19.12. I did check version of the gcc and kernel built by the gcc version. I also checked the following commands. # cat /proc/version Linux version 2.6.18-194.el5PAE (mockbuild@x86-007.build.bos.redhat.com) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-48)) #1 SMP Fri Oct 29 22:00:21 EDT 2010
[Code]....
View 10 Replies
View Related
May 27, 2011
I got the nVidia driver and Compiz installed. Everything's running fine . But then I tried crtl+alt+F1 - which worked though the font was way too big - and then crtl+alt+F7 to get back to the Desktop but it went to a black screen and blinking cursor instead. I searched a bit and it seems this was a problem a few years back but nothing recent. FWIW, I don't have this problem with Hardy/nVidia/Compiz on another drive in this same machine. Is there a way to fix this?
View 3 Replies
View Related
May 6, 2010
I recently followed instructions to enable the nvidia driver. run the following commands:
[Code]....
then rebooted, a tricoloured loading bar appeared and finished, then all i got was a blank screen with flashing cursor. I don't get a prompt to login and can't access my account. I am dual booting on this machine with ubuntu, is there anyway i can restore my fedora partition and enable my nvidia graphics
View 6 Replies
View Related
Jan 19, 2010
Im trying to add the binary NVIDIA-Linux-x86-96.43.14-pkg1.run in my CentOS 5.4 ks.cfg file. The problem is that when you manually run the program it asks you questions and you have to respond with ok if you agree to their licensing terms. I want to be able to include this binary in my kickstart so when my machine boots up for the first time this driver is already installed and I don't have to waste time troubleshooting video issues. Is there anyway I can do this?
View 3 Replies
View Related
May 21, 2010
I am posting this to hear if there are others with display issues on Dell E6500 laptop with the Nvidia Quadro NVS 160 driver. This problem is starting to annoy me a great deal, but I am uncertain how I should move forward. In short; I have Ubuntu 10.04 x64 installed on my Dell E6500 laptop. When using only the laptop, everything works great. The second I plug it into the docking station (the laptop lid closed) and want to use my two external monitors (Dell 2001FP) I'm in trouble. I cant see anything and what I get is a 'DVI: Cannot Display this Mode' on the primary monitor - If i try a regular VGA cable I get nothing but a black screen.
I have played around with the Nvidia config but it cant find my monitors and therefore I cant do much. I am aware of the various "hack the xorg.conf" options, but I before I do that I wanted to see if others had experienced the same thing. I had hoped that we were pasted the hack stage and that primary functions such as display would work by now.
View 9 Replies
View Related
Apr 29, 2011
After installing debian squeeze I tried installing a nvidia driver. I had to type: /etc/init.d/gdm3 stop The nvidia driver wouldn't install because the 'make' command was missing in a path or something. Now I cannot get the GUI anymore. startx gives me a blank screen rebooting the computer gives me a blank screen. I can only boot in recovery mode. but the nic doesnt work so no internet connection.
View 1 Replies
View Related
Dec 10, 2009
I have just installed OpenSUSE 11.2 on an Intel DQ35JO motherboard and XFX 9500GT 512MB video card. After installation the desktop looked fine on the Sony LCD TV I have connected to the 9500GT via a DVI to HDMI cable.
After the first reboot after installation I added the Nvidia repository via the add community repository function in the software sources option in YaST2. I then proceeded to install the Nvidia G02 drivers and the nvidia-settings package. At this point after a reboot I would get a blank screen. Hitting ctrl-alt-F1/F2/F3/F4/F5/F6 has no effect, I could not get any of the virtual consoles to appear. I had to SSH into the box and reboot into runlevel 3.
Once I had rebooted into runlevel 3 I logged in as root and executed "sax2 -r -m 0=nvidia" and got an error message that the configuration server could not be started. I tried executing "sax2 -r -m 0=vesa" and received the same error:
[Code]....
View 9 Replies
View Related
Feb 14, 2010
I am running Debian Squeeze ( kernel 2.6.32-trunk) 64-bit on this machine - "most" of the hardware can talk to Linux or vice-versa. I am, however, having trouble finding a suitable free / non-free driver to work with the abovementioned card. It would seem that this card is too "new" at the moment (February 2010).
View 3 Replies
View Related
Nov 24, 2010
I have repeatedly installed CentOS 5.5 64-bit on a Dell T3500 with an nVidia Quadro FX 580, in an attempt to get dual monitor support to work to no avail. Everything works fine when just one monitor is plugged in and I do not try to enable or plug in a second monitor. I have installed the Dell DKMS, and the Dell recommended drivers (from Dell site) on one installation, I installed the nVidia drivers (from nVidia site) on another, and have tried with what CentOS loads by default on another. The results are the same every time: When I reboot as directed I get a black screen. I can recover by hard shutdown and unplugging one of the monitors, but that doesn't solve my problem. Has anyone had a similar experience, or have any helpful guidance? I am not very Linux savvy. This is for multiple machines in a corporate environment.
Information for general problems.
== BEGIN uname -rmi ==
2.6.18-194.26.1.el5 x86_64 x86_64
== END uname -rmi ==
== BEGIN rpm -q centos-release ==
centos-release-5-5.el5.centos
== END rpm -q centos-release ==
[Code]...
View 3 Replies
View Related
Feb 18, 2009
I recently purchased a Quadro FX 4800 and tried to install it on Fedora 10. During the installation, Fedora didn't recognize my new graphics card and began installing the OS in text mode. I stopped the installation and tried to start over, this time I passed the following command: linux resolution=1024x768. I then proceeded with the installation, and again, I was posed with a text mode installation. I continued with the text mode install and when Fedora was done installing, I rebooted and system just locked up.
At this point I was frustrated, so I reinstalled my old 8800 graphics card and started a new install with something that worked in the past. When the install was done, I loaded the latest NVIDIA drivers and the rebooted. I reinstalled my new graphics card (Quadro FX 4800) then powered up my system. I thought everything was good to go and all of a sudden my system flickered and then locked up during the 'Anacron' testing phase. I then rebooted with the "Ctrl+Alt+Del" hotkeys, but my system always locks up during the 'Anacron' testing sequence. I am aware that the Quadro FX 4800 is a few months old, but how can I get it to work in linux? It has gotten so bad, that I had to resort to using MS Vista.
System specs:
Intel Core Duo Quad Core
4 gigs DDR2
SATA RAID 0
Mobo: 680i SLI
800WATT Power Supply
View 5 Replies
View Related
May 9, 2010
I am having the same problem, as soon as X tries to load my screen just goes blank. I have an ATI Radeon 9550. At first I tried switching between VGA and DVI as well but upon ruling that out, I switch to my on-board video card and that is working thus far, but I'm trying very hard to figure out a way to be able to switch back. Anyways I'll check back in later on if I have any new information I will post.
View 3 Replies
View Related
May 25, 2010
I installed [URL] and everything mixed up! I tried to remove it and I get this error: Error while creating client module OneClickInstallUI My Graphic Card is NVidia Quadro FX
View 5 Replies
View Related
