My F11 system display goes blank after some time of inactivity and I cannot see how to disable it. It does not appear to t eht screen savers (all turned off). I have an NVIDIA card,, is it in the card?
View 8 RepliesRunning 2.6.33.3-85.fc13.i686 and just purchased a AGP 7600GT 512 video card. Searched around and found:I did the rpm, yum, sed, mv & dracut as directed. Then I rebooted. When it starts up (all the normal bios messages) and then I 1/2" bar across the bottom of the screen with Fedora 13 on the right end and .... nothing. Just sits there. I've used my Live-13 disk and tried to reverse the procedure but I'm starting to think it's the video drivers.
View 4 Replies View RelatedI ran the latest updates this week (including the new kernel and the new kmod-nvidia update) and I got a blank screen when I rebooted. (I get the Fedora bar across the bottom of the screen, then after that the screen goes blank) I assume this is when the xorg server is trying to start..
I went into single user mode , backed up and then removed the xorg.conf file but still got a blank screen upon reboot.
I rebooted into single user mode, copied the /var/log/Xorg.0.log file to a safe location, and then restored the system back to its original state.
I've since rsync'd my system back to where it was before the update.
Here's my Xorg.0.log file:
I've posted this to the fedora mailing list with no response, my apologies if it's been addressed here...
I have an IBM Thinkpad with an Nvidia card ( nVidia Corporation GT218 [NVS 3100M] (rev a2) )
I currently have the nouveau driver black listed in my grub.conf setup: rhgb quiet nouveau.modeset=0 rdblacklist=nouveau
I did the update which installed/updated the following:
---> Package kernel.i686 0:2.6.35.14-95.fc14 set to be installed
---> Package kernel-devel.i686 0:2.6.35.14-95.fc14 set to be installed
---> Package kernel-headers.i686 0:2.6.35.14-95.fc14 set to be updated
---> Package kmod-nvidia.i686 1:280.13-2.fc14 set to be updated
However when I reboot the system boots to a blank screen, and even the previous kernel boots to a blank screen. I tried installing akmod-nvidia but get the same results
I've restored the system back to before the update for now..
I recently followed instructions to enable the nvidia driver. run the following commands:
[Code]....
then rebooted, a tricoloured loading bar appeared and finished, then all i got was a blank screen with flashing cursor. I don't get a prompt to login and can't access my account. I am dual booting on this machine with ubuntu, is there anyway i can restore my fedora partition and enable my nvidia graphics
I have a little brother who is handicapped and uses the machine he was sat by the computer with a blank screen at which point my dad soft rebooted the machine (he will sit at the machine if its not working but he cant tell us its not working). I don't know if the below caused the machine to stop displaying?
Code:
I did a fresh install of 8.04 alternate disk with LVM then updraded to 10.04 (due to lack of any spare CDs around).
Everything was working fine but wanted to try to get the nvidia-173 drivers installed (I have an old FX5200). Can't start into X now as my plasma says mode unsupported.
At one point I managed to boot into recovery mode then root terminal and removed all nvidia packages and reinstalled nvidia-173 only and followed the instructions listed on the 10.04 release candidate page. Still stuck with the unsupported modes error on my TV though. I have a 720p plasma display (1366x76, I usually run 1280x768 without issues. I'm guessing it is the refresh rate set in the new xorg.conf that is throwing me off, how to adjust this?
An issue that's complicating things however is that when I try to boot into recovery mode I get an error stating 'pcspkr' driver already registered, aborting... then it hangs there until I ctrl-alt-delete and force a restart. This is preventing me from getting to the point where I can select a a root terminal to try to fix my errors.
I have used 8.04 exclusively for a few years and wanted to try something new (still not all that adept at linux setup).
EDIT: I managed to get to root again and just removed the xorg.conf file and that seems to work somewhat. Except now I can't boot as I get a looping mountall: Plymouth command failed that hangs up the process.
I have just bought a Dell Optiplex 960 with a NVIDIA Quadro NVS 450. Everything works out of the box with the 10.04.1 Live CD. It suggests to install and activate NVIDIA proprietary drivers, but you need to restart the machine afterwards. The problem is that, after that, all what you get is a blank screen, with not even a cursor. The same happens when you install Lucid: blank screen with no cursor. Ctrl+F1 does not show anything, but Ctrl+Alt+Prnt Scrn+REISUB works and the PC is reset. In the var directory the logs show that the NVIDIA module is not loaded.
View 2 Replies View RelatedI installed OpenSuse Gnome version 64 bit on a HP laptop DV7 Intel Dual Core with nVidia 9600 GM cardAll went well, until after I had installed the nVidia drivers from this page: NVIDIA drivers - openSUSEI selected the Geforce 1-click install and Yast went on to installl all the packages (a lot of 32-bit),took about half an hour.I logged out/in, and could work as normal, until I rebooted. Maybe I waited not long enough (5 minutes), but the screen was blank, then I gave up.Anyone has an explanation. I can always re-install everything, but then what went wrong with the nVidia package
View 9 Replies View RelatedI have just performed an upgrade from OpenSUSE 11.2 to 11.3. My Machine is a Lenovo W701DS laptop which uses an NVIDIA FX3800M graphics card. The system was working fine under 11.2 before the upgrade.
After upgrading to 11.3 the splash screen after GRUB comes up for about 1 second before the screen goes blank. After about 5 mins I am able to SSH to the Laptop and access the system. Doing this I created an xorg file using "X -configure" and copied the new file to the /etc/X11 directory and renamed to xorg.conf.
If I SSH to the laptop change run levels to init 3 then init 5 the Gnome comes up and I have graphics the system works However I am unable to access the text consoles using alt+f1, f2 etc. If I restart the system it is back to the blank screen.
I have attempted to install the NVIDIA drivers however the installation fails due to an error with gcc or kernel source versions. Error log reports that the kernel was complied using a different version of gcc.
I have installed Ubuntu Maverick 10.10 RC in my PC, everything works fine, but after install Nvidia proprietary Graphics driver it boot up on a blank screen (I can hear the login sounds, etc) but screen is absolutely black.
I try to login in recovery mode and check if something is wrong but nothing happens (even adding noveau driver to a blacklist (editing grub)) Now I have re installed Ubuntu 10.04.1 and works fine but I would like to install the 10.10 version, since I have this inconvenience, I cant do it.
My graphic card: Nvidia Gforce 8400GS 256MB Pci Express
i did yum -y install akmod-nvidia and then type xconfig-nvidia on the terminal,and after logging off i confront with a blank screen,so i remove akomd-nvidia [yum remove akomd-nvidia] and also yum erase xorg-x11-drv-nouveau [yum erase xorg-x11-drv-nouveau]but still no gui,i think i should install:
yum install kmod-nvidia
xorg-x11-drv-nvidia-libs.i686
xorg-x11-drv-nvidia-libs.x86_64 [but i didn't]
so how can i have my gui back?
Just upgraded my system from 13.0 to 13.1 Most things went pretty smoothly, but I tried 'startx' before the post-upgrade/config reboot and the system hung - "time to upgrade my video drivers", I thought. Upgraded to Nvidia 195.36.15*. X works perfectly, and a modprobe shows the 'nvidia' module loaded. So far so good.
However, when I try to use any vesa modes in lilo, I get a blank screen after the BIOS check and the system hangs - even toggling numlock on or off won't work... So I can only boot up in text mode. This makes me unhappy, partially because I like penguins, but also because it is an absolute insult to my new (old) monitor. I thought this could be to do with the nouveau conflicts reported by -current users some days ago, but the respective blacklist file is present so I'm stuck as to what to do... *I've tried 195.36.15, 195.36.24 and the latest 2xx beta drivers. All exhibit the same behaviour.
EDIT - forgot to post my video card specs. It's an 8500gt w/ 256mb, 128-bit DDR3.
I got the nVidia driver and Compiz installed. Everything's running fine . But then I tried crtl+alt+F1 - which worked though the font was way too big - and then crtl+alt+F7 to get back to the Desktop but it went to a black screen and blinking cursor instead. I searched a bit and it seems this was a problem a few years back but nothing recent. FWIW, I don't have this problem with Hardy/nVidia/Compiz on another drive in this same machine. Is there a way to fix this?
View 3 Replies View RelatedI have just bought a Dell Optiplex 960 with a NVIDIA Quadro NVS 450. Everything works out of the box with the 10.04.1 Live CD. It suggests to install and activate NVIDIA proprietary drivers, but you need to restart the machine afterwards.The problem is that, after that, all what you get is a blank screen, with not even a cursor.The same happens when you install Lucid: blank screen with no cursor.
Ctrl+F1 does not show anything, but Ctrl+Alt+Prnt Scrn+REISUB works and the PC is reset.In the var directory the logs show that the NVIDIA module is not loaded.
I'm installing 10.10 on a desktop with Nvidia 6150 that needs nomodeset on boot or i get the blank screen upon boot. I had to force the live CD to nomodeset when booting from the CD. I was finally able to install, but upon the first boot from the hard drive I'm getting the blank screen again. How do I boot with nomodeset and get to my installed ubuntu. Once I get there i can edit my grub settings.
View 3 Replies View RelatedAfter installing debian squeeze I tried installing a nvidia driver. I had to type: /etc/init.d/gdm3 stop The nvidia driver wouldn't install because the 'make' command was missing in a path or something. Now I cannot get the GUI anymore. startx gives me a blank screen rebooting the computer gives me a blank screen. I can only boot in recovery mode. but the nic doesnt work so no internet connection.
View 1 Replies View RelatedI have just installed OpenSUSE 11.2 on an Intel DQ35JO motherboard and XFX 9500GT 512MB video card. After installation the desktop looked fine on the Sony LCD TV I have connected to the 9500GT via a DVI to HDMI cable.
After the first reboot after installation I added the Nvidia repository via the add community repository function in the software sources option in YaST2. I then proceeded to install the Nvidia G02 drivers and the nvidia-settings package. At this point after a reboot I would get a blank screen. Hitting ctrl-alt-F1/F2/F3/F4/F5/F6 has no effect, I could not get any of the virtual consoles to appear. I had to SSH into the box and reboot into runlevel 3.
Once I had rebooted into runlevel 3 I logged in as root and executed "sax2 -r -m 0=nvidia" and got an error message that the configuration server could not be started. I tried executing "sax2 -r -m 0=vesa" and received the same error:
[Code]....
HP Pavilion Media Center a1430n Desktop PC
Athlon 64 X2 (T) 3800+ 2.0 GHz
Asus A8N-LA chipset GeForce 6150 LE
1 gB of RAM
Video Graphics: integrated
Hipro hp-d3057f3r max out put 300w
Here is the problem fist i had a 8800gt installed it work fine until one time the card stop displaying on my screen and the card would make a fan sound like if was over heated......but my integrated still displays... ok then i send the card to my provider so it can be replace.. so they send me a 8800gts .... and i installed and deleted the old drives and even upgrade my bios .... but still happen like it happen whit the 8800gt it wont display any thing on my screen and also is making the same fan sound of the 8800gt ....
I am having the same problem, as soon as X tries to load my screen just goes blank. I have an ATI Radeon 9550. At first I tried switching between VGA and DVI as well but upon ruling that out, I switch to my on-board video card and that is working thus far, but I'm trying very hard to figure out a way to be able to switch back. Anyways I'll check back in later on if I have any new information I will post.
View 3 Replies View RelatedI am trying to install fedora 12 on my computer. I have burned the live cd ISO and it works just fine until right before it shows the login screen. I suspect that it may have to do with my ati radeon 9800 graphics card. give me some boot options or some such thing so that I could install fedora on my computer. Also some other specs
ASUS A7N8X Mother Board
AMD Athalon XP
1GB ram
when i start uubuntu it automatically goes to tty with out letting me login. then when i press startx it says:
NVIDIA: failed to initialize the nvidia graphics device pci:0:13:0
nvidia: please check your systems kernal log for additional erroe
nvidia: messages and refer to chapter 8
nvidia: failed to initialize the nvidia graphics device!
nvidia: screen found, but none have a usable configuration
fatal screen error: no screen found
right before this i had activated a nvidia graphics device
Screen is blanking out after x minutes. Don't know how to set it to not do that.
View 14 Replies View RelatedI have been having an issue with my screen blanking out after a few minutes (number of minutes unknown), since I reinstalled Fedora 12 (KDE) a couple of weeks ago. I have tried, yes, a lot of things to try to set it so that it doesn't blank out, to no avail. I have spent a lot of time on the Fedora forum seeking resolution, with a variety of suggestions, all to no avail. I went into System Settings > Power Control, and fooled with things around there and they didn't work. I tried xset and dpms and shutting them off. Still no cigar.
View 9 Replies View RelatedI was able to get Fedora 10 to run on VirtualBox. Since the system wouldn't let me set the resolution to anything bigger than 800 x 600, I decided to get the nVidia driver (I'm running the nVidia 8400m G). I did it through this guy's tutorial: [URL]... After rebooting, I see the loading bars and everything, but I get a blank screen with a cursor. After pressing ctrl+alt+F3, I was able to log in to the root and execute the "akmod builds the required kmod on bootup" under the "For GeForce 8 series" [URL]... After a reboot, I still get the same thing. Will I have to reinstall Fedora 10 and just not update the nVidia graphics drivers? I have a 20" monitor that has a resolution of 1600 x 1050 and I would really like to take advantage of that.
View 14 Replies View Relatedi had a serious problemafter i checked my hardware detected by using liveCD, there's no problem i thoughti successfully installed it on my PCbuti got blank/no screen appeared when it started up
View 1 Replies View RelatedIm trying to install fedora 10 on the ps3 but i get a blank screen after the media test question, i tested the media in this case the CD and it says it has no errors but when it goes to install it switches to a blank screen and gets stuck. Can anybody help me, or tell me what im doing wrong. Steps that i taken.
1.Download the ppc version of fedora10.
burn the ISO-image using the lowest possible setting.
2. i made a foder in my usb stick called PS3 and inside has another folder called otheros then inside it has the file otheros.bld
3. formatted the ps3 using the xmb. to 10 gigs for the other OS.
4. install Other OS using the usb stick that i made, install successful.
5. switch to other OS, using the XMB through systems settings.
6. Next I see a cd , i click on it with a mouse, see two penguins two options install 32 bit or 64 bit, i choose 64 bit.
7. then i get a media test question , choose skip and loads from CD.
8.Switches to blank screen and nothing else happens.
i'm running on fc 11 x86_64 i'm start my computer with blank no boot or bios boot at all. i also dont know its because of hardware failure or fc11
View 2 Replies View RelatedWhenever I boot the system after the fedora 12 bubble fills up I see a blank screen with a blinking cursor. Though I am able to access tty2 by pressing alt+ctrl+F2.
I have seen the boot logs and it shows a warning:
Code:
Warning: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/
I have an ATI Radeon 3xxx series card and I have recently installed mesa-dri-drivers.x86_64. I guess the blank screen problem is because xorg for fedora 12 doesn't support these drivers.
I want to remove this package using yum, but when I try to do it using "yum remove" it shows 95 packages that would be uninstalled with it. I don't want to remove those packages as it has some that I use like Konversation.
how do I remove mesa-dri-drivers and what were the drivers that were being used before I installed mesa.
i installed fedora 12 on my pc and I also installed the ati drivers from atiand i rebooted and booted back in fedora all i get is a blank screen that does nothing
View 5 Replies View Related