I am running Debian Squeeze ( kernel 2.6.32-trunk) 64-bit on this machine - "most" of the hardware can talk to Linux or vice-versa. I am, however, having trouble finding a suitable free / non-free driver to work with the abovementioned card. It would seem that this card is too "new" at the moment (February 2010).
View 3 RepliesI have Lenovo Thinkpad R400 laptop. It has Intel Centrino Core 2 Duo processor with ATI Radeon 3400 series graphics card and Intel Mobility chipset series 4 Integrated graphics controller. I have Squeeze ( stable) installed on it with kernel 2.6.32-5-686 .
My laptop gets very hot within 10 minutes whether I do any task or not. Also battery life is almost 40% as compared to Windows. I am more worried about temperature as it remains completely cool in windows. Mostly CPU load remains around 10% and CPU spends 99.99% time at 800MHz clock. I believe heat generated is by graphics card chipset.
Following are some information about my machine
$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
[Code].....
I have Debian Squeeze x64 on ThinkPad T61p with standard 2.6.32-5-amd64 kernel. thinkpad_acpi loaded as module, suspend to RAM works fine from menu in KDE as well as by closing the lid, however machine doesn't appear to react on pressing Fn+F4 which should put it to sleep as well. I've read through thinkpad_acpi documentation and asked Google but so far can't find the solution. Can anyone, point me in correct direction?
View 6 Replies View RelatedJust got a new Thinkpad W510 at work. It has a combined headphones & mic connector. Unfortunately, I cannot find an adapter for my regular headset with separate headphone & mic jacks. So I have to revert to using a USB Soundcard Adapter that came with the headset. Unfortunately I am running into problems with this too.
Code:
I'm not sure what happened, I enabled Nvidia support and all of sudden the internal layout of windows, look..well old-school, like they did back 10 years ago. The screen-shot explains all. I'm sure this is just a setting SOMEWHERE in Gnome but I'd be danged if I can find it.
View 5 Replies View RelatedI have Centos 5.5 running on this laptop but can't get gobi_loader(loads firmware onto the 3g device and then you can use wvdial) working on kernel 2.6.18-194.11.1.el5 (x86_64). lsusb shows the Gobi device but gobi_loader uses /dev/ttyUSB0 which doesn't exist.
View 18 Replies View RelatedI installed Debian Squeeze (choosing no when prompted to add support for non-free or contrib sources) and noticed that the fan of my Nvidia 9600 GT video card is constantly running at full speed. I thought this meant that the default driver is not properly working. I would like to configure my system so that the video card fan is not being pushed so hard.
I downloaded the latest Nvidia (propietary) driver, stopped gdm3, and ran the driver installer. The installer failed because it said the Nouveau kernel driver was currently in use and incompatible with the Nvidia driver. I chose not to allow the installer to update my modprobe configuration directory. nvidia-installer log file '/var/log/nvidia-installer.log'
[Code]...
It looks at though the xorg.conf.new file has the nv driver in use, but the Nvidia installer says the Nouveau driver is being used. I ran a line in terminal (i forget the exact line) to test the xorg.conf.new file in the /root/ directory. The result was No Screens Found.
Next, I tried to remove the xserver-xorg-video-nouveau package using aptitude, but it displayed a message indicating that xserver-xorg-video-all depends on it. I decided not to remove the xserver-xorg-nouveau package. Any suggestions on how to proceed in order to configure X with a free driver (nv, vesa, or nouveau) so that the video card is handled properly?
Anyone have any comments or issues with running debian on a Thinkpad SL510?
[URL]
It has the Intel GM45 chipset, Intel Core 2 Duo, and Intel GMA 4500MHD video. I guess I am concerned about the wireless as well but cannot seem to fine the brand card it has.
I have a new Thinkpad T520 from work and am trying to put Debian 6 on it. I previously had a Thinkpad T42 and was able to install Debian 6. I recall having to find the driver and install it separately, so I downloaded all of the non-free drivers, but the network detection step doesn't seem to let me select my own driver.
I've been thru this at least 4 times, both the standard 6.01 and the AMD64 bit version, both behave the same. This has the (unfortunately) the Thinkpad b/g/n wireless card, but the wired ethernet is the Intel 82579LM gigabit. Seems there would be a driver with Debian 6 that would support that one.I can't stand running Windows 7.
I am trying to get Debian 6 to work on an hp Z400 - the problem is that it came with a NVIDIA Quadro NVS 295 graphics card; there may be a driver for Linux, but it doesn't matter, because GRUB insists on switching to some sort of graphics mode and the screen just blanks and switches itself off. Is there any way to make sure during installation that GRUB gets configured to stay in character mode only?
View 6 Replies View RelatedUsing online Debian guide, installed latest nvidia-current, glx etc which seems to be 195.xx Machine boots to GUI but monitor setting menu doesnt respond nor is there an nvidia specific one. xorg.conf shows 'nvidia' driver but I suspect I am still on 'nouveau' since the synapatic package manager doesn't show an nvidia xserver-xorg-video choice.
Second question, any trailheads for using wheezy based drivers (i.e. nvidia's latest 270.xx) with squeeze?
I'm trying to install the nvidia drivers but it is not working.
lspci | grep VGA
02:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX - nForce GPU] (rev a3)
My xorg.conf looks like this:
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
[code]...
And after that my X is not working. And when i try sudo modprobe nvidia I get this:
FATAL: Error inserting nvidia (/lib/modules/2.6.26-2-686/nvidia/nvidia.ko): No such device
I have same problem described here:
http://www.thinkwiki.org/wiki/Problem_w ... e_clicking
The command: #hdparm -B 254 /dev/hda -- works
Now, I should create:
an executable file named 00DISK in /etc/pm/sleep.d with the following content
I just built myself an new workstation and now only 2 of 3 monitors are working. I built the nvidia driver by downloading it and installing with ./Nvidia...Before when I ran nvidia-settings I saw two GPUs listed but now I only see one. Xorg Config (Not sure how I ended up with 3 devices in there):
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:39 PDT 2010
Section "ServerLayout"
# Removed Option "Xinerama" "1"
[code]...
My wireless network is down. I got thinkpad x120e, chipset: Realtek RTL8188CE, driver: rtl819ce.
Here is what I did so far:
upgraded to 2.6.38-bpo.2-686
installed firmware-linux-nonfree
Added the firmware file from the repo since it's not yet packaged in firmware-realtek and reloaded the module.
'iwlist sc' shows: 'wlan0 Interface doesn't support scanning : Network is down'
'dmesg |tail -20' shows:
rtl8192ce:rtl92c_download_fw():<0-0> Failed to request firmware!
firmware 0000:04:00.0: firmware_loading_store: vmap() failed
I also tried the following commands:
ifdown wlan0 ; ifup wlan0
ifconfig wlan0 up
Relevant bug: [URL]
Step by step, in case someone is interested:
add to sources.list: deb [URl] squeeze-backports main
aptitude update
sudo aptitude -t squeeze-backports install linux-image-2.6.38-bpo.2-686
install this package: [URL]
get the first file: [URL]
add to driver:
mkdir -p /lib/firmware/rtlwifi
mv rtlwifi_rtl8192cfw.bin /lib/firmware/rtlwifi
modprobe -r rtl18192ce; modprobe rtl18192ce; dmesg | tail -20
I have just bought a Dell Optiplex 960 with a NVIDIA Quadro NVS 450. Everything works out of the box with the 10.04.1 Live CD. It suggests to install and activate NVIDIA proprietary drivers, but you need to restart the machine afterwards. The problem is that, after that, all what you get is a blank screen, with not even a cursor. The same happens when you install Lucid: blank screen with no cursor. Ctrl+F1 does not show anything, but Ctrl+Alt+Prnt Scrn+REISUB works and the PC is reset. In the var directory the logs show that the NVIDIA module is not loaded.
View 2 Replies View RelatedI don't know if these are related, but I have had occasional lockups, where no input has any effect and then it shuts down, and am usually unable to resume from suspend on closing the lid.
Here are the specifics. Thinkpad x120e, AMD e-350, ATI radion 6310 graphics, Intel 320 series SSD 80 GB, no bluetooth.
The ethernet and wireless cards, as given in lspci, are
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
04:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01)
[Code].....
Like the title says, I have the Quadro NVS 135M in my Dell D630. It's working (well, besides the startup screen issue - Plymoth... not a fan!), but when I watch a movie the image ?flickers? annoyingly. This is something I have never experienced before, with allegedly ?inferior? video cards. It's odd though, isn't it - better video card, inferior output!?!
View 1 Replies View RelatedI'm new to linux and trying to install the driver for Nvidia quardo fx 380 lp in redhat 5.4.From the Nvidia site I got the driver for this card to be NVIDIA-Linux-x86-260.19.12. I did check version of the gcc and kernel built by the gcc version. I also checked the following commands. # cat /proc/version Linux version 2.6.18-194.el5PAE (mockbuild@x86-007.build.bos.redhat.com) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-48)) #1 SMP Fri Oct 29 22:00:21 EDT 2010
[Code]....
I come here every two or three years, when I have some troubles with my graphic card. Indeed, once again. Since last Tuesday, I experience some system freeze. Since yesterday, I must run on low graphic mode. As there has not been any X.org or driver update, I suspect that my graphic card is running down. But I do not know how to diagnose this.
My configuration:
-- Dell Latitude D820 laptop;
-- processor Intel Core 2 Duo T7200 (2.0GHz 667MHz FSB);
-- bi-canal 2x1024Mo DDR2-SDRAM 533MHz memory;
-- graphic card NVIDIA Quadro NVS 110M 256MB;
-- 15.4" WSXGGA+ (1680 x 1050) LCD screen;
-- 100Go SATA (7200 TPM)) hard-drive;
-- 8x DVD +/- RW burner;
-- battery 9 cells 85 WHr LI-ION;
-- Bluetooth card for Latitude;
-- Intel PRO/Wireless 3945 802.11a/g;
-- Ubuntu Linux 9.04 Jaunty Jackalope desktop 64 bits real-time kernel.
Some commands results:
Code:
$ lspci | grep -i vga
01:00.0 VGA compatible controller: nVidia Corporation G72M [Quadro NVS 110M/GeForce Go 7300] (rev a1) .....
Trying to install 64bit onto Dell T3500 with NVidia Quadro NVS 295. Live Cd works and Install completes. When I boot I get BIOS and Disk info then boot switches to flashing cursor after disk read and then Monitor goes into sleep mode.
View 6 Replies View RelatedIm trying to add the binary NVIDIA-Linux-x86-96.43.14-pkg1.run in my CentOS 5.4 ks.cfg file. The problem is that when you manually run the program it asks you questions and you have to respond with ok if you agree to their licensing terms. I want to be able to include this binary in my kickstart so when my machine boots up for the first time this driver is already installed and I don't have to waste time troubleshooting video issues. Is there anyway I can do this?
View 3 Replies View RelatedI have just bought a Dell Optiplex 960 with a NVIDIA Quadro NVS 450. Everything works out of the box with the 10.04.1 Live CD. It suggests to install and activate NVIDIA proprietary drivers, but you need to restart the machine afterwards.The problem is that, after that, all what you get is a blank screen, with not even a cursor.The same happens when you install Lucid: blank screen with no cursor.
Ctrl+F1 does not show anything, but Ctrl+Alt+Prnt Scrn+REISUB works and the PC is reset.In the var directory the logs show that the NVIDIA module is not loaded.
I have repeatedly installed CentOS 5.5 64-bit on a Dell T3500 with an nVidia Quadro FX 580, in an attempt to get dual monitor support to work to no avail. Everything works fine when just one monitor is plugged in and I do not try to enable or plug in a second monitor. I have installed the Dell DKMS, and the Dell recommended drivers (from Dell site) on one installation, I installed the nVidia drivers (from nVidia site) on another, and have tried with what CentOS loads by default on another. The results are the same every time: When I reboot as directed I get a black screen. I can recover by hard shutdown and unplugging one of the monitors, but that doesn't solve my problem. Has anyone had a similar experience, or have any helpful guidance? I am not very Linux savvy. This is for multiple machines in a corporate environment.
Information for general problems.
== BEGIN uname -rmi ==
2.6.18-194.26.1.el5 x86_64 x86_64
== END uname -rmi ==
== BEGIN rpm -q centos-release ==
centos-release-5-5.el5.centos
== END rpm -q centos-release ==
[Code]...
I have a set of vm's with stable, testing, and sid to keep track of how things are going. When I did an apt-get dist-upgrade with squeeze last week, things seemed to OK (350 package updates) until the end. It didn't seem to like and / or was confused by a kernel dependency.
I am not too concerned yet. Because these are in vm's, I do a snapshot before any significant change. I can futz around with impunity because I have that backup.
I re-booted, and tried the apt-get dist-upgrade again with same results. I think I also tried apt-get -f install.
So I reverted to the snapshot, and will simply try again in the future. I recall that with lenny as testing, the font-desktop was really screwed up for about a period of 6 weeks.
However, just in case someone else runs into this:
1) a re-boot worked, but the failure of apt-get made me nervous enough to revert.
2) waiting for corrections has seemed to work in the past (with a single exception with a 4-disk SCSI software RAID10 update that failed to re-boot lenny successfully after what seemed to be a minor update -- that was on a real system, not a vm. I haven't gotten back to look at that.)
I recently purchased a Quadro FX 4800 and tried to install it on Fedora 10. During the installation, Fedora didn't recognize my new graphics card and began installing the OS in text mode. I stopped the installation and tried to start over, this time I passed the following command: linux resolution=1024x768. I then proceeded with the installation, and again, I was posed with a text mode installation. I continued with the text mode install and when Fedora was done installing, I rebooted and system just locked up.
At this point I was frustrated, so I reinstalled my old 8800 graphics card and started a new install with something that worked in the past. When the install was done, I loaded the latest NVIDIA drivers and the rebooted. I reinstalled my new graphics card (Quadro FX 4800) then powered up my system. I thought everything was good to go and all of a sudden my system flickered and then locked up during the 'Anacron' testing phase. I then rebooted with the "Ctrl+Alt+Del" hotkeys, but my system always locks up during the 'Anacron' testing sequence. I am aware that the Quadro FX 4800 is a few months old, but how can I get it to work in linux? It has gotten so bad, that I had to resort to using MS Vista.
System specs:
Intel Core Duo Quad Core
4 gigs DDR2
SATA RAID 0
Mobo: 680i SLI
800WATT Power Supply
I am posting this to hear if there are others with display issues on Dell E6500 laptop with the Nvidia Quadro NVS 160 driver. This problem is starting to annoy me a great deal, but I am uncertain how I should move forward. In short; I have Ubuntu 10.04 x64 installed on my Dell E6500 laptop. When using only the laptop, everything works great. The second I plug it into the docking station (the laptop lid closed) and want to use my two external monitors (Dell 2001FP) I'm in trouble. I cant see anything and what I get is a 'DVI: Cannot Display this Mode' on the primary monitor - If i try a regular VGA cable I get nothing but a black screen.
I have played around with the Nvidia config but it cant find my monitors and therefore I cant do much. I am aware of the various "hack the xorg.conf" options, but I before I do that I wanted to see if others had experienced the same thing. I had hoped that we were pasted the hack stage and that primary functions such as display would work by now.
I just got done installing Ubuntu on a new harddrive and set it up to dual boot with grub loader. However, when I boot into Ubuntu, the screen goes black. I can however login (blind) by hitting enter and typing password. The login sound goes and it logs in, however, the screen stays black. I am running a NVIDIA Quadro NVS 295 Video Card.
View 9 Replies View RelatedI installed Debian Squeeze with no issues. I went to install latest Nvidia driver as done previously with Lenny. Used instructions that worked on lenny from "the trooper" [url]
Downloaded th latest driver for my GeForce 7300 GS vidio card, driver package NVIDIA-Linux-x86-260.19.12.run
Used "method # 2 as described in HOW TO,as it worked perfectly in the past on Lenny. Only syntax I changed was instead of gdm I typed gdm3 as it appears that is the new name for gnome in Squeeze.
Did as folows:
Now the trouble showed up, Unfortunatly I can only go off my memory. A question was asked stating that something did not match, it needed a 3 and the driver had a 4 version or somethng of this sort. then it asked if I new what I was doing (and I lied) and selected yes. And whammo, it didn't work. (This question was asked when i did in Lenny and it is working perfectly still on that system). I now can not boot to GUI, I notice when system boots it starts in "S" mode although I select normal boot from grub2.
Not too bad if I got to reinstall as little is on the system. I just want to know what I am missing on the instalation deal or should I be going about this difrently with Squeeze.
I recently just installed Squeeze on an ia64 system and was having some troubles with running VNC.I get the following error, more specifically for some reason I get a malloc - memory corruption error:
Xtightvnc(9165): unaligned access to 0x60000000001ea06c, ip=0x4000000000268280
Xtightvnc(9165): unaligned access to 0x60000000001ea074, ip=0x4000000000268280
Xtightvnc(9165): unaligned access to 0x60000000001ea07c, ip=0x4000000000268280
Xtightvnc(9165): unaligned access to 0x60000000001ea084, ip=0x4000000000268280
[code]...
After display all the code above, it just stops. The port 5901 is still closed - if it runs properly, would it open automatically?Is there something that is incompatible? Or am I missing some system configuration component?