Ubuntu Multimedia :: A Recent Update Has Caused IEC958 Output To Stop Working?
Feb 1, 2011
I've recently noticed that my IEC958 digital audio output has stopped working. The short version of why I didn't notice this immediately is that I have two simultaneous audio outputs from my system to my speakers and I hadn't realized the IEC958 output wasn't in use.After messing around with a few settings to no avail, I remembered that I'd recently run update manager (this had to be within the last two weeks) and thought this might be the cause.I have just booted to a 10.10 install disc and verified the IEC958 output works fine there.
Unfortunately I'm not sure which of the recent updates could have caused this problem. Before I submit a bug report on launchpad I was hoping anyone here might have a suggestion as to where to look to figure this out.I'd recently seen this thread and this thread which lead me to believe it may have been a recent kernel update.What's my best course of action to determine the problematic update?[edit]In case anyone needs the info, I'm running Ubuntu 10.10 64 bit on a system with an Intel DH57JG motherboard. Using the HDMI output to a TV, with a separate optical audio cable to my speakers.Also, I've attempted using all of the available digital audio output options in the sound preferences panel and I've also installed gnome-alsamixer and tried enabling/disabling every digital output listed there as well. None of these got the optical output working again.
View 4 Replies
ADVERTISEMENT
Sep 19, 2010
Macbook Pro 7,1 (current model) - sound worked after adjusting as described here: [URL] Sound stopped after allowing system to update today.
View 5 Replies
View Related
May 2, 2010
i have an Asus P5Q with ALC1200 integrated sound card. I've upgraded today my system from Ubuntu Hardy 8.04 to Ubuntu Lucid 10.04. In Hardy all was working ok, but in Lucid i have no sound, SPDIF (IEC95 seem not working.
View 9 Replies
View Related
Aug 8, 2011
Seems like the latest Kernel (2.6.40-4.fc15.i686) update screwed with my setup a little bit.
This is what happened:
I had about 100 updates to my F15 pending in my taskbar's update notifier.
I let the system update itself.
Reboot and desktop effects don't work.
Takes a long time to open up Dolphin.
electricsheep (OpenGL screen saver) doesn't work.
I'm assuming it's a problem with OpenGL or my nvidia video drivers which I tried reinstalling from mjmwired's guide.
That didn't fix anything.
I'm looking for a point in the right direction or a way to revert back to my previous state before the system updated everything.
View 1 Replies
View Related
Mar 3, 2010
I think an update or something has killed Samba on my Karmic box. it can see Windows shares OK, but it no longer appears on the Windows network.I have not changed my smb.conf for months, so something else has been modified.Looking in the logs I can see the following in "log.winbindd-idmap" after restarting Samba
Code:
[2010/03/03 10:07:20, 0] winbindd/idmap.c:201(smb_register_idmap_alloc)
idmap_alloc module tdb already registered!
[2010/03/03 10:07:20, 0] winbindd/idmap.c:149(smb_register_idmap)
[code]...
All other networking seems fine (internet, Synergy+ etc) it's just sharing out to the Windows network that is broken.
View 2 Replies
View Related
Dec 4, 2009
Yesterday I ran an update on my Acer Aspire One, which I operate under Fedora11. Amongst the updates was also an update for Qjackctl and the jack audio connection kit. After the update I could not start Qjackctl anymore and all my possibilities with rosegarden and my USB keyboard and fluidsynth were gone. I restored to the system before update ran the update again excluding the two packages concerning jack. Perfect, it works again. So it seems that there is a bug inbedded in the update. By the way, I am quite happy with Qjackctl as the connection tool between my various music making options, which are not very fancy, but I enjoy them. Despite comments in other parts of this forum Qjackctl works very well on the Atom based AAO. I have a kind of protocol of the failure of qjackctl and what I did. I can make that available if necessary
View 2 Replies
View Related
Sep 4, 2010
I have an EEE 1000 that successfully connected to WPA networks until yesterday. I tried re-installing the RT2860 drivers that had been previously modified and did not have success.
Additionally, I just installed 10.04 on a Gateway laptop that's a few years old. It immediately connected to the WPA network and I ran the updater. Lo and behold, after updating it no longer connects to the network.
View 4 Replies
View Related
Aug 7, 2011
My PC has a broadcom wlan adapter. When I clean installed Fedora 15 about two weeks back, the wifi wasn't working on its own. I searched the internet and found out that installing broadcom-wl and akmod-wl would solve the problem. I tried it, and the wifi started working after that.
Wifi not working means there is no wireless option in the network settings and the wifi indicator light is off.. when wifi started working both of these got fixed
Now i did a yum update yesterday, after which my wifi has stopped working again. No use of reinstalling broadcom-wl, akmod-wl, or even kmod-wl...
Code:
lsmod
gives
Code:
wl
[Code]....
[URL]
View 2 Replies
View Related
Feb 25, 2010
Firefox 3.6 "Namoroka" stopped working after a recent update. Clicking on my panel launcher or the launcher in the applications menu does nothing. I even tried starting Firefox from the terminal and got an error message: "(firefox-bin:3592): GLib-WARNING **: g_set_prgname() called multiple times", whatever that means.I would be willing to rip out Firefox and start all over again but I don't know how to remove the 3.6 version. I couldn't find a method in the Software Center for doing that graphically.
View 7 Replies
View Related
Sep 1, 2011
I have ubuntu 10.04. After update I performed yesterday, I could no longer access from other computers shared folders on my ubuntu machine. I checked update history and it included the following that appeared to be related to network shares:
Code:
libsmbclient (2:3.4.7~dfsg-1ubuntu3.4) to 2:3.4.7~dfsg-1ubuntu3.7
libpam-smbpass (2:3.4.7~dfsg-1ubuntu3.4) to 2:3.4.7~dfsg-1ubuntu3.7
samba (2:3.4.7~dfsg-1ubuntu3.4) to 2:3.4.7~dfsg-1ubuntu3.7
samba-common (2:3.4.7~dfsg-1ubuntu3.4) to 2:3.4.7~dfsg-1ubuntu3.7
[Code]..
I would prefer to use the latest version because it includes security updates. Does anyone know if there's some trick to getting network shares to work with the latest version of libsmbclient?
View 7 Replies
View Related
Apr 14, 2011
after a recent update my policykit permissions stopped working, and I can't understand why.An example: mounting a flash drive requires password, hinting on rg.freedesktop.udisks.filesystem-mount. /usr/share/polkit-/actions/org.freedesktop.udisks.policy has the following:
Code:
<action id="org.freedesktop.udisks.filesystem-mount">
<description>Mount a device</description>
[code]....
View 5 Replies
View Related
Aug 20, 2010
Today, I installed the recent kernel security update (i.e. 2.6.32-24-generic #41-Ubuntu SMP). After a reboot, the sound is gone.
From my user account:
mpc@awd:~$ alsamixer
cannot open mixer: No such file or directory
Same problem with "aumix".
However, the commands "sudo alsamixer" and "sudo aumix" seem to work (but still no sound).
"lsmod | grep snd" will give
snd_hda_codec_atihdmi 2367 1
snd_hda_codec_realtek 203310 1
snd_hda_intel 21941 0
[Code]....
View 6 Replies
View Related
Aug 8, 2011
After recent upgrade which contained the newer kernel ( 2.6.35-30-generic). I've started to experience problems with sound and video in programs - deadbeef and totem. Both of them dont play any sounds and video in totem is skipping every 3-4 seconds (the same applies to flash videos in browser).
As I run deadbeef from the command line I dont get any significant information. I run ubuntu 10.10 amd 64. I tried to reinstal gstreamer my programs and codecs with no luck.
View 4 Replies
View Related
Mar 30, 2011
Recent update is causing problems with the top and bottom panels not to show when I restart and or start my acer aspire one netbook. It takes several retries to try to get it to show. I don't know what the possible problem is my guess is the gdm3 is the one causing the problems.
View 1 Replies
View Related
Apr 16, 2011
I run the 2.6.32-5-686 kernel on Squeeze and the bad nvidia drivers. A recent update, and pardon for not noting which, broke 3d games on my box. From a terminal neverputt yields the following error:
ignatius@lapbox 14:56 [ ~ ]:$ neverputt
X Error of failed request: BadWindow (invalid Window parameter)
Major opcode of failed request: 137 (NV-GLX)
[code]....
I can mv xorg.conf to xorg.conf-pre and nexuiz will fire-up. Without 3d of course. I spent an hour or so last week going over my xorg.conf but it just ain't broke! Someone else saw it, too, and reported it but his post remains alone in the thread as of 10 minutes ago.
View 5 Replies
View Related
Jul 24, 2010
After recent update (yesterday) Evolution became almost unusable: if I am going to create a new e-mail or just select a person from Contacts or reply to someone it simply crashes. The update also didn't go very smooth - 15 updates were not applied because of a broken dependency - evolution-exchange, which depended on evolution prior to 2.30.0 but 2.30.1.2-2 was to be installed. Is there a way to make Evolution to work or upgrade solving dependencies?
View 3 Replies
View Related
Feb 9, 2011
Scaleo Pentium 4 system with several HDDs 3Gb RAMUBUNTU 8.04 (I think) inside a 50Gb partition (J:)Operating dual boot with Windows XP all OK until ......sanctioning the updates. Now Ubuntu will not complete a boot up.Studio Starts to scroll its name then screen goes back to A/numemeric reports and hangs for time-outs which never resolve. Power - down only way to exitExample of screen report at point of stopping:-
Starting hardware abstraction layer hold
104.628464] ata3.00 revalidation failed (errorno -5)
{DELAY FOR TIME-OUT} THEN:
[code].....
View 1 Replies
View Related
May 19, 2010
After recent update (yesterday) Evolution became almost unusable: if I am going to create a new e-mail or just select a person from Contacts or reply to someone it simply crashes. The update also didn't go very smooth - 15 updates were not applied because of a broken dependency - evolution-exchange, which depended on evolution prior to 2.30.0 but 2.30.1.2-2 was to be installed. Is there a way to make Evolution to work or upgrade solving dependencies?
View 1 Replies
View Related
Feb 7, 2010
according to aplay -l my computer (a Dell Dimension 5000) should have an IEC958:
[Code]......
But where? There's nothing on the backside of the computer nor on front, I cannot find SPDIF on the mainboard itself either.
View 1 Replies
View Related
Nov 26, 2010
I have a headset microphone plugged into the built-in audio input. The output is plugged into an amplifier > speakers.
Pulseaudio is "helpfully" routing the microphone input signal to the speaker output. I do not want this. I go to pavucontrol and disable the "monitor of the internal audio analog stereo" -- and what I say into the microphone is still coming out of the speakers.
Google gives a lot of information about how to live-stream mic input over the Internet. And, I found this here (that's for karmic, I'm running lucid):
[URL]
... but that's about how to ENABLE loopback. It says loopback should not be enabled by default, but I very clearly hear that something is doing the same thing as loopback.
(Of course, I need to hear sound from applications that are playing, and when I'm dictating text into NaturallySpeaking running under virtual box, I need sound input to go there -- so turning the mic all the way down to zero is not the solution.)
I'm fairly sure I remember hearing this behavior ever since installing Ubuntu, and I didn't do anything to turn it on. I can't imagine most users would prefer this behavior -- if it's the default behavior, why? It makes absolutely no sense to me. (Sorry. It's one of those piddly little configuration things that costs a couple of hours of web searching time, and after a while I just have to give up, but not before becoming much more frustrated than I should have to.)
So, to be clear, here's what I want:
- Applications playing audio should send sound to the main output.
- Applications receiving audio input should hear the microphone.
- Microphone sound should not EVER go to the main output unless I have explicitly launched an application making the connection. (The signal goes input -> output even when NO application is open - hence my consternation.)
View 1 Replies
View Related
May 26, 2010
I'am using ubuntu lucid, after today's system updates, mysql stop working at all. Log file at /var/log/mysql/error.log does not say anything about today, and whe I try to start it the terminal hang also in verbose mode.
View 9 Replies
View Related
Dec 17, 2010
yesterday I let the update manager install a whole bunch of updates for my 10.04 install on my MSI Notebook ER710. My wireless was just working peachy until then (with the madwifi drivers), but after the update, no more... I checked the madwifi, tried a new make, but nothing worked.
So, after reading somewhere that 10.10 had less issues with wireless I decided to upgrade to 10.10 in the hope that that would solve my problem.
Well, partly it did, as in, according to my system I've got a wireless again and this morning even, it was able to see wireless networks! Unfortunately I couldn't connect to mine, although the key was correct. At some point I lost the ability to see wireless networks again. I tried wicd too, but no luck their either. It recognizes my card but can't see any networks.
here is all the info:
Machine Brand and Model (PC/Laptop): MSI ER710
lspci
Code:
02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
[Code].....
View 1 Replies
View Related
Oct 23, 2010
I'm trying to get my Audigy 2 Value to output digital but when I try to use the iec958 interface it outputs to the front speakers analog outputs, ie not the digital io socket.
I can get 5.1 surround by using the plug:surround51 device.
Have gone though other guides trying to fix the problem but no luck. how to get the digital stuff working. I have included some outputs.
Code:
Code:
View 3 Replies
View Related
Jun 29, 2009
after updating my machine, my ppp connection stops working. It dial ok, but fail when call the post scripts. Here is the log for the command
Code:
ipup ppp0:
Code:
Jun 29 16:50:42 ricardoalonso ifup-ppp: pppd started for ppp0 on /dev/ttyUSB0 at 460800
Jun 29 16:50:42 ricardoalonso pppd[4516]: Warning: can't open options file /root/.ppprc: Permission denied
[Code]....
View 4 Replies
View Related
Jan 7, 2011
I have installed the wifidrivers needed to use the wifi on the 1018 in Ubuntu Netbook Edition. It works until I get asked to install 5 (Sorry, don't remember their name) more updates, now I can not see Wireless networks under the networkmanager, It does not help installing the driver again, and I can not remove it either. It says the driver is activated but not in use. Also note that in desktop mode I lost my other workspaces, I can not change what window is on top and the quit, minimize and full window on windows is not there anymore.
View 2 Replies
View Related
Sep 9, 2010
As usual, I let the update manager run.. But now something bad happened and a red button is showing in the system tray, which when I hover my mouse over it, tells me to open package manager or try "sudo apt-get" in terminal to see what is wrong..
If I enter sudo apt-get upgrade, I get the following errors.. How can I fix it.. I am unable to open package manager itself..
Code:
E: Problem parsing dependency Depends
E: Error occurred while processing gconf2 (NewVersion1)
E: Problem with MergeList /var/lib/dpkg/status
E: The package lists or status file could not be parsed or opened.
View 2 Replies
View Related
Jan 30, 2011
The sound stopped working on my Macbook Pro 1,1. It was working fine before, and I can't think of any changes I made that would make it stop working. I know it's not a hardware problem because the Apple sound plays when I turn on the computer. Everything is unmuted in ALSA Mixer. None of the hardware options in Sound Preferences produce sound. Plugging in headphones or speakers does not solve the problem. I'm using 10.10.One curiosity: Whenever I do something that would normally cause sound to play, the optical audio red light in the headphone jack turns on, but no sound plays.
View 2 Replies
View Related
Aug 4, 2011
I just updated a bunch of things on my system (10.10 x86_64) via synaptic and when I rebooted to finish the update everything looks horrible. All the Icons are different, taskbar is all gray, compiz is acting funny, and the top bar has different icons and coloring. I'm wondering what happened and how I can fix this... I'm guessing it might be the nvidia update, but I'm not sure, here is what I did for the update/install:
Upgraded the following packages:
libsmbclient (2:3.5.4~dfsg-1ubuntu8.4) to 2:3.5.4~dfsg-1ubuntu8.5
libwbclient0 (2:3.5.4~dfsg-1ubuntu8.4) to 2:3.5.4~dfsg-1ubuntu8.5
linux-headers-2.6.35-30 (2.6.35-30.54) to 2.6.35-30.56
[code]....
The only other thing I changed was to turn off the auto-login so I wouldn't have that damn keyring password dialog pop up during login.
Should I try downgrading the NVIDIA package update or look through any particular logs to see what happened?
View 2 Replies
View Related
Jan 17, 2010
I have been working with Ubuntu for the last 6 months. Overall, I am all behind linux and open source. However, what I cannot figure out is why [in Ubuntu] or how can an app work for a while, then stop working within the same distro? My iPod was working great with HiPO, Banshee, and Rhythmbox and now, after the latest upgrade, it's not working.
View 3 Replies
View Related
Jun 14, 2010
I had Ubuntu working perfectly until I installed updates for the proprietary Nvidia drivers.Now Ubuntu freezes at the Ubuntu loading screen. Im using Ubuntu 10.04 64bit.I used to know how to access the terminal at bootup but I no longer remember.
View 5 Replies
View Related