I noticed that after compiling 2.6.35.4 that gnome-alsamixer has two new options for my ASUS XONAR D2X: "Dac Filter" and "Dac Oversampling", (I turned them both on and off and didn't notice any difference)
View 1 RepliesI just got a Xonar D1 (chipset CMI 8788 ).
It partially works but I got a couple of issues (using 10.04 x86-64). I use it with a Stereo headphones and a mic.
1) It only outputs in 7.1/5.1 mode and only on the left headphone. If I reselect 7.1/5.1 while an audio stream is playing then I get stereo back. I've checked with Ubuntu 10.10 live CD and apparently the left channel is mapped to front, while the right is mapped to sub-woofer. How can I fix this?
2) The mic doesn't work. When I select the Xonar D1, I can choose between Analog Input, Analog Line In and Analog Microphone. When I switch between those I can hear a click coming from my pc, as if something HW is switching. I tried playing around with alsamixer but it doesn't work. Any idea how to make the mic work?
I'm hoping some smart boffin around here could help me getting my asus xonar DX (PCI-e) working in debian 5. iv searched the net.
View 3 Replies View RelatedI recently bought a decent sound card, the Asus xonar D1. Prior to purchase, I checked the Alsa matrix to make sure that it is supported. I couldn't get it to work after putting it in, so I did a clean install of Suse 11.2. Initially, it didn't work, but after I installed alsa-firmware, it worked. However, flash videos had no sound. I remembered something about this when I fist installed 11.2 with my older card. I looked it up and figured out that it was the PCM issue. However, when I opened kmix, there ws no PCM mixer. I even looked through the "hidden" mixers, making them all visible and maxing each out all without success.
Next, I started the "SDB:AudioTroubleshooting" process. When I got to step 2, I deleted the configurations of the xonar card configuration in Yast. I rebooted and lost all sound. I then started over with the "SDB:AudioTroubleshooting" and could not get anything, though I have not gone through updating Alsa, as I hope it is not necessary.
[Code]...
how to install alsa drivers along with Asus xonar dgx sound card. I followed these instructions. URL....And until "Setting up modprobe and kmod support" instructions were clear. I should put something in /etc/modules, but I dont down exactly what.
Code: Select allroot@SERVER:~# aplay -lL;
**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC887-VD Analog [ALC887-VD Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
Code: Select allroot@SERVER:~# lspci -nn | grep -i audio;
00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05)
02:04.0 Multimedia audio controller [0401]: C-Media Electronics Inc CMI8788 [Oxygen HD Audio] [13f6:8788]
[code]....
I've just brought a Asus Xonar DG and put it in my case - and found out that it's about the only card that is not easy to get working.I've updated my ALSA to 1.0.24 using this how-to. Then I reinstalled pulse with all the utilities and got it to look like working, with one problem only: no sound is output.I use Rythmbox for playback. In pavucontrol the bar below the soundcard output indicates that there's something playing, but no sound gets to my headphones. Has anyone encountered that? I've tried nearly all combinations of setting the output devices in various places like Sound settings and pavucontrol, but none worked.
View 4 Replies View RelatedI just bought a Xonar D2X. Wonderful thing - recording from mic and quality of output to speakers is superb... on my Windows install. : /
It appears to work correctly in Kubuntu 10.10 as when I open up Sound and Video configuration, I can see it listed correctly and when I hit "Test", I get the annoying Ubuntu tinkle-plonk. But no application I use seems willing to use it. In fact, both Optical Outs (the motherboard's and the soundcards) are working fine when I try playing a test sound from this panel, but neither seems to be output to by VLC, Spotify or anything else I've tried.
I have set the entry "Xonar D2X Multichannel (IEC958 (S/PDIF)) Digital Audio Output to the preferred option for all output. Silence.
How do I convince VLC, Spotify et al, that the card really is there and they're really, really welcome to use it?
I'm running Ubuntu 11.04 x32, and after some research I haven't succeed getting my soundcard to work.Soundcard is detected but not sound comming from speakers.This is what aplay -l says:
Code:
card 0: STH6 [Xonar ST+H6], device 0: Multichannel [Multichannel]
Subdevices: 1/1
[code]....
It seems my Xonar soundcard is not detected by Suse, is there anything I can do about this?
View 9 Replies View RelatedUbuntu 10.10 x64 worked out of the box for me but there is one irritating issue.
I have Xonar DS(Oxygen HD Audio) with analogue 2.1 speakers and spdif passthrough to nvidia GTX260 hdmi output for my tv.
It makes random cracking noise on tv unless something is played, no matter on analogue or digital output, then is noiseless.
Alsa 1.0.23, kernel 2.6.35
Is there a way to filter static or noise out of an mp3? I have avidemux and audacity but I'm not sure how to go about it, or if its actually possible.
View 5 Replies View RelatedI was just wondering whether there is some way to permanently turn on the Extrastereo filter in SMPlayer. I have to turn it on every time manually
View 3 Replies View RelatedI mostly need it to filter away background noise from interviews. So, the editor should allow me to tweak the recordings in the frequency domain. I'm a Kubuntu user, so, if possible, propose me KDE apps!
View 1 Replies View RelatedI'm installing ffmpeg with libavfilter using this guide but i can not get the movie filter to compile when passing --enable-avfilter-lavf to ffmpeg i'm using libavfilter r5935 and the test copy of ffmpeg.
View 3 Replies View RelatedI just installed Ubuntu 10.04 and set up ALSA and got my DS working perfectly.I booted back into Windows with the intention of playing some BC2, and discovered anytime sound tries to play, it's all screwed (I can still make out some of what is being said but it's pretty bad). Naturally my first reaction would be to go into the Xonar audio center, which I did, and made sure nothing was wrong there. I changed settings around (sample rate and changing from headphone to 2 channel) but nothing worked. Turned off the D3SD GX and that didn't work either. Removed the drivers, rebooted, reinstalled, rebooted. No change.
One thing I noticed is under the Windows sound control panel it doesn't show I'm playing anything when I am. However when I go into advanced and use the test option (and set it to the highest option available) it sounds fine.Under Ubuntu it also sounds fine. I've got volume set to around 50% in Ubuntu. I noticed when I muted it under Ubuntu and rebooted it was muted under Windows, hence my thought that the volume settings were messing things up. Didn't work though.Pulled the card out and left it out for a few minutes worked. Quite strange.
ASUS A6000 no headphones ASUS A6000 no headphones using ubuntu 10.4 and after ALSA upgrade script was run.
At first had no sound and then ran the ALSA upgrade script found here. [URL]
Now have sound but no headphones.
Also, when attempting to adjust outputs I used the ALSAmixer gui application and seem to have misconfigured the display somehow. I now only show one item at a time on the panel and none of the other controls show up. I can still select them...one at a time. There is no user manual for this application, the older versions have a manual but it does not apply to the new gui version of the app.
I've seen several posts with people having problems of the speakers not muting when headphones are plugged in.I have no sound from my speakers to begin with.I am by no means an ubuntu expert, so please bear with me.From what I've seen, there are many variations of the Asus K52F. Mine has an Intel Pentium P6200 processor. So far as I can learn, it's got a Conexant sound chipset. Ubuntu does not even seem to recognise that a sound card is present.
View 1 Replies View RelatedI have a Xonar DS, specifically the card with the lspci line
Code: Select all03:05.0 Multimedia audio controller: C-Media Electronics Inc CMI8788 [Oxygen HD Audio]
this card has worked for years on an ubuntu 12.04 installation. It worked on ubuntu 14.04 (but then I got fed up with the U thing and moved to Debian Wheezy).So on Wheezy, sometimes this card is recognized by Alsa, but sometimes not. After a reboot the card may be present or not. The modules that are supposed to know about this card (snd_oxygen, snd_virtuoso) are loaded in either case but are not used.
I'm new to Ubuntu and have a problem with my built in cam my computer is an ASUS L58LE cam is usb 2 uvc 1.3 webcam (/dev/video)
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 003: ID 064e:a116 Suyin Corp.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
i have an Asus P7p55D Deluxe motherboard and the audio seems to be working but the mic don't =/ besides that i have an Ati card that also have a hdmi output.
View 1 Replies View RelatedI've spent the whole day trying to get xbmc to run on my Asus EB1501P. It seems impossible to get the sound to work.
I've installed ubuntu and xbmc acording to the wiki:
[URL]
But I can't eaven get analogue audio from the device.
Have anyone succeeded with this ?
I'm almost at the point of giving up and installing win7 instead =/
I have an Asus N82J and I don't have sound? Where I can start?
View 9 Replies View Relatedafter searching a lot and trying to re-install Alsa and pulse-audio, trying the older kernell, editing the alsa-config files and a lot of reboots I cant get any sound out of my new laptop. It worked 2 or 3 times, and if I leaved Windows with audio disabled it would never work in Ubuntu, but now I cant ever get any sound from my speaker. The laptop is pretty new/recent, and it as an Bang&Olufsen ICEpower speaker with a gorgeous quality that I never expected from a laptop. I use Ubuntu in a lot of my programming classes and at home to to study and also to program micro-controllers and to play a bit with open-cv to do some image processing. So having sound is almost a must, programming hours and hours with no sound is driving me crazy :/
The laptop an a Core i7 64 bits processor but I'm using a 32 bits Ubuntu 10.04 because I'm also part of the robotic soccer team of my university and they can run code compiled in 64 bits machines so I just opted from the 32 bits distro to remain compatible, everything is working fine now, the graphics card as also given some fight, but its now running perfectly.
Code:
tiago@tiago-laptop:~$ cat /proc/asound/card0/codec#* | grep Codec
Codec: Realtek ALC269
tiago@tiago-laptop:~$ uname -r
2.6.32-30-generic
[code].....
I also posted this as a question in launchpad, but wasn't sure if this might be a better place. Pretty new to Ubuntu, if you couldn't tell.I just upgraded from 9.04 to 9.10 and cheese/skype don't see the webcam built into my machine. It worked with Windows 7 that came with the computer, and in 9.04. I'm using a Asus 1005PE.
result from lsusb:
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[code]....
Ever since switching to Ubuntu (Hardy at the time) I have had no luck getting my TV Tuner to work. I think the closest I have come is finding this information but it didn't really help and I'm not sure if it's relevant. Can anyone help? I have attached the relevant output of lsusb -v***EDIT***Further to this I have read these instructions and I get the following result.
Code:
michael@michael-laptop:~/v4l-dvb$ sudo modprobe dvb-usb-dib0700
WARNING: Error inserting dib0070 (/lib/modules/2.6.32-19-
[code]....
I have a Asus EEEBOX EB1012 and everything except the sound is fine. I can use a normal 3,5mm stero plug and get sound, but neither optical och HDMI sound will work. HDMI picture is no problem.I have made sure nothing is muted/not turned on in alsamixerI have tried every "profile" under Sound PreferencesI have tried Alsa upgrade scriptI have tried getting rid of pulseI have tried getting different drivers for the Nvidia cardI have tried Ubuntu 10.04 and 9.10At this point I'm at a loss and don't know what else to do. Has anyone had any luck with HDMI sound on a EB1012 or the ALC662 card?I have several other devices hooked up via HDMI, Xbox 360, Playstation 3, PC (Windows) and none of them are problematic so I'm pretty sure it's related to the ASUS/Ubuntu somehow.
View 4 Replies View RelatedI have an asus G73 JW laptop and when I look at all the profiles under material tab, there is not one that includes the .1 of the subwoofer, I have stereo, 4.0 surround but no .1 .... When I play music no boom boom comes out of the sub...
View 9 Replies View RelatedI has just got Asus N53JN, i have tried to installed both Ubuntu 10.04 and 10.10 but the speaker not work.lspci | grep Audio00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06)
cat /proc/asound/version
Advanced Linux Sound Architecture Driver Version 1.0.23
aplay -l
**** List of PLAYBACK Hardware Devices ****
card 1: Intel [HDA Intel], device 0: ALC259 Analog [ALC259 Analog]
[code]....
I am trying to get the Asus "My Cinema-U3100 Mini plus" DVB-T USB stick to work on my lucid 32bit with 2.6.32-27 kernel - with no great success so far. And this despite searching through forums and following the instructions given on [URL].
The USBID is in fact
Code:
ID 0b05:1779 ASUSTek Computer, Inc.
Which is exactly the one shown in the list of supported devices on LinuxTV. I have implemented all modifications and corrections to the source files as outlined in the above LinuxTVWiki instructions.
I also added the boot option
Code:
usbhid.quirks=0x0b05:0x1779:0x0004
to grub2 in order to overcome the (initial) problem of the tuner being recognised as a HID device.
My dmesg output after plugging in the device now shows
Code:
Jan 27 17:44:50 jens-laptop kernel: [ 1086.358488] usb 2-5: new high speed USB device using ehci_hcd and address 6
Jan 27 17:44:50 jens-laptop kernel: [ 1086.495359] usb 2-5: configuration #1 chosen from 1 choice
When I try to compile the af903x driver using
Code:
sudo make
The response on the screen is
Code:
make -C /lib/modules/2.6.32-27-generic/build SUBDIRS=/home/jens/Desktop/Linux_PC_AF9035_Afatech_2008.12.17/Linux-32bit_AF9035_20081217/AF903x_SRC modules
make[1]: Entering directory `/usr/src/linux-headers-2.6.32-27-generic'
CC [M] /home/jens/Desktop/Linux_PC_AF9035_Afatech_2008.12.17/Linux-32bit_AF9035_20081217/AF903x_SRC/af903x-core.o
In file included from /home/jens/Desktop/Linux_PC_AF9035_Afatech_2008.12.17/Linux-32bit_AF9035_20081217/AF903x_SRC/type.h:4, .....
make: *** [default] Error 2
My knowledge is limited and I have no idea why I am getting all these warnings and finally the error message. Also, is there a way to tell when (or if at all) driver support for this device will be implemented in the Linux kernel?
how poor is sound playback in Ubuntu? I don't know if this is a general problem in all distros, but as a beginner i decided to install Ubuntu as its popular for users with minimalistic or not much knowledge about Linux at all. So in Windows playback sound quality is great, but in Ubuntu it is terrible, why is that? My soundcard is motherboard integrated - Asus M4A77TD PRO. In other forums someone give me advice to write this
[Code]....