My laptop was shut down normally, but when it restarts - it just shows the very first image (Toshiba something....) which is the screen where it says what commands to type to get into bios.
After this - the screen shows nothing more. All black, except some faint (extremely faint) lines...
I don't know - my first thought was that the screen itself was caput, but since it shows the initial screen - I guess it's not...
10.04 runs perfectly most of the time, then every once-in-awhile it crashes. The screen goes black and I have to restart. I had a similar problem with 9.10, so I reverted back to 8.04 which never crashed. I did a fresh install of 10.04.
View 9 Replies View Relatedı want to setup ubuntu 10.04 but everytime I face black screen and crash...I have toshiba L650-11F...during the installation ,if only in installation page ,help of f6 ı selected acpi=off, after install ubuntu 10.04 , ı don't open ubuntu...black screen and crash..
View 9 Replies View RelatedRecently my laptop running Ubuntu 10.10 has had an abrupt power shutoff (actually several times -- my battery has some problems).
Now when Ubuntu boots, I get the startup screen, but after a few seconds, the screen goes black. I can still boot from the live CD and in fact I am using my computer from the CD to write this post.
A few more details: When I press the power button while my computer is in this "blank" state, I get hard drive activity. Also, if I press "power", and then "enter", the machine actually shuts down.power
Following the instructions in this post I'm able to boot and work using the live-cd option (Try without installing). The trick is, of course, adding 'nomodeset' to the boot sequence.
Now, my problem is to add 'nomodeset' to the "normal" boot sequence - the one on my hard disk. I'm running Ubuntu on an LG E300 with ATI Radeon Xpress 1250.
I recently decided to give Ubuntu another try after a break for a while, and have hit a bit of a road block The live CD booted fine, ran, installed, all flawlessly, so it's now a dual boot with Windows 7. Only issue now is when trying to load the HDD installed Ubuntu, it just hangs on a black screen, no HDD activity light or anything. First up my specs code...
Next, what happens in detail:
Machine posts, loads boot loader with OS options. Whether choose Ubuntu or recovery Ubuntu, it always hangs on black screen straight after that.
Next, what I have tried to fix it so far:
Tried pressing 'e' and replacing the quiet splash with nomodeset, same result with both normal flavour and recovery.
Tried copying the xorg.conf from the live CD filesystem to X11 folder on main system drive. Also tried editing it to try and use generic vesa driver.
I've been using Ubuntu for about a year or so and have never had any problems installing it up until now.
I can boot from live CD for 9.10, but if at any point I attempt to install it to my hardrive, it either locks up or the screen goes black. Sometimes I'm able to start the installer, but the screen will go blank. The most progress I've been able to make on the install was up to 98% before it locked up, every other time I've gotten a blank screen or a lock up around 40-60%. After a hard reboot I get an error that reads "DISK BOOT FAILURE. INSERT SYSTEM DISK AND PRESS ENTER"
This problem doesn't only occur with 9.10, but with every other linux distro I've tried on it. My first attempt was with Ubuntu Studio, but I got similar errors. I've searched literally for hours and have found nary a solution that even comes close to solving my problem. using HP Pavilion a404x desktop
After installing Ubuntu Server 10.04 LTS, I restarted my machine. I removed the disk, but now when it starts, it never gets to GRUB. Instead, it just takes me to a black screen with a blinking cursor. I can't type in anything and holding shift doesn't take me to GRUB.
View 9 Replies View RelatedMy laptop screen will go black while i'm using it. I do not have any screensaver enabled. It just goes black (whenever) and I have to reboot to use my machine again
View 5 Replies View RelatedGot a problem with Ubuntu 9.10 and a Lenovo T400 with an ATI Radeon Mobility HD3400 and ATI drivers /ATI contol center. Whenever the laptop wakes up from power-saving mode, the screen goes black (with some jagged mulicolored lines).
View 2 Replies View RelatedI'm having problems with the screen going black on startup in 10.10. It appears to go completely off (no backlight or anything). If I press ctri+alt+f1 I get a terminal, then I can ctrl+alt+f7 and the desktop appears. I have tried setting the mode to the correct resolution in xorg.conf and I tried using the vesa driver, but it still doesn't work. My graphics card shows as sis 661/741/760
View 5 Replies View RelatedI installed Ubuntu 10.10 to dual boot alongside Windows 7 on a Dell Inspiron. This worked fine and after restarting it seemed to be working normally, after the first boot into windows though when I tried to restart the laptop again I just get a blank screen with a blinking cursor in the top left instead of the grub screen.I'm still able to boot the LiveCD fine and tried to reinstall Ubuntu but the exact same thing happened? Anyone know what's going on/how to fix this?
View 9 Replies View RelatedWhenever I use the function hibernate or sleep - or just generally close my lid on my laptop, my laptop displays a black screen when I open the lid again - though it is turned on.
Basically, it hibernates/sleeps the laptop when I close the lid. When I open the lid though, it turns on the laptop, but brings me a black screen.
Code:
I have a sony vaio laptop(model-VPCCW27FX) 64 bit.I am currently using windows 7 os. I tried installing ubuntu using wubi and also by making a bootable disc. The installation proceeds well. When I restart my laptop, it asks whether to start windows or ubuntu.But, when I select ubuntu, the screen goes blank.
View 1 Replies View RelatedI like to suspend my laptop when I close the lid. I have squeeze installed. When I open the laptop lid all lights indicated that it coming out of suspend but the monitor stays black. It is worse since I install the ati drivers for the card instead of the xorg. It did it with both but worse with nonfree drivers. I can get it to come out by ctrl alt f2 and the ctrl alt f7. However yesterday that did not work but that was the first time. My laptop is an acer 5251-1513 amd processor v120, and hd 4250 radeon
View 6 Replies View RelatedI'm running Debian Squeeze on a Dell Studio 1558 laptop, and I have my laptop set to suspend when my lid is closed. Resuming from suspend seems to work but the screen remains blank, forcing me to hard reboot every time. Upon reading this thread
Code:
Tue Jun 21 23:07:12 AKDT 2011: performing suspend
Tue Jun 21 23:07:28 AKDT 2011: Awake.
[code]...
The screen of my years-old HP laptop (running Natty) freezes and eventually turns black. Ctrl-Alt-F# works to switch to the terminals. My fan is even louder than usual. I spend some time fooling around with ps and kill and shut down some of the most resource-consuming processes, which quiets the fan a bit, but tty7 still shows a black screen except for my mouse pointer.
I finally decide to shut it down altogether, but then I think to myself, "Self, you've used the power switch to shut down before in this situation, but shouldn't there be a more proper way to do it in the terminal?" So I try shutdown, I have trouble with it, it proceeds to get hopelessly tangled up, and it looks like it's frozen up in mid-restart when I throw up my hands and decide to go for the old power-switch-for-five-seconds method after all. Now when I start the computer and select Ubuntu from GRUB, I get this:
[Code].....
I'm running Debian Squeeze on a Dell Studio 1558 laptop, and I have my laptop set to suspend when my lid is closed. Resuming from suspend seems to work but the screen remains blank, forcing me to hard reboot every time. Upon reading this thread:
Tue Jun 21 23:07:12 AKDT 2011: performing suspend
Tue Jun 21 23:07:28 AKDT 2011: Awake.
Tue Jun 21 23:07:28 AKDT 2011: Running hooks for resume
[code]...
I have a laptop and an external monitor connected via displayport. I can configure both displays via settings with correct resolution and arrangement. However, this configuration is not sticking, and every time I shut down the laptop or close the lid I will need to fight with black screens and more to bring the same configuration again. Basically, it seems that the monitor is "stealing" the primary role to the laptop's native screen (I have it configured as secondary, but also being primary the configuration gets messed).
After many trial & errors, this is the routine I have found to make things work every time I boot / awake the system:
1. Boot. Laptop's display shows the booting sequence.
2. When the login screen should appear, laptop's display goes black, monitor shows background.
3. If I press F9 to increase brightness, the brightness icon appears in the monitor, but it is stuck at the minimum.
4. The only way to leave this point is by pressing F7 (project screen) and then F9 again to increase brightness. Then the laptop's screen does light up.
This is when I'm lucky. Sometimes the configuration goes mad and I get mirrored displays and different resolutions, without touching the settings myself. Also, if I unplug the displayport I run the risk of getting stuck with a black screen in the laptop, without any way of recovering the GUI other than rebooting (Ctrl Alt F2 will still show the command line screen).
My system is Debian 8 testing up to date, running in a Lenovo T430 with Intel components. I'm not sure the monitor is relevant here, but in any case it is an Eizo CS240.
I have an Asus z9100 laptop with an Intel 855GM integrated graphics chip, which is running Karmic (the purpose of the laptop is to be a MythTV frontend so my understanding is that it needs to run 9.x in order to connect to the MythTV 0.22 backend - I have installed and configured this using the installable Mythbuntu package) and the laptop is subject to this bug which causes random freezes:
[URL]
So, following advice for similar freezes I've seen, I have added the following options to my grub menu.lst on the kernel line:
nolapic nomodeset
and I have edited xorg.conf so that it makes use of the vesa driver instead of the Intel driver. This results in no freezes and if I wanted to watch Myth on the laptop screen I'd be squared away. However, the laptop has a damaged screen so the point was always to output the signal to an external monitor via its VGA out.
When I attach the external monitor and boot with the setup as described, the external monitor is never detected. But I noticed that if I remove the "nolapic nomodeset" from the kernel boot line, it is detected. However, signal is only output to it during the earliest part of boot (when the Ubuntu logo is in the center of the screen before the full-screen graphic with the animated progress line), after which the external monitor goes black and all the display output goes to the laptop screen. The external monitor power button is still lit up green as if it has been detected and is receiving signal, but it's just a black screen.
get the signal out to the external monitor after the initial part of the boot process, using the vesa driver? Here is the current state of my xorg.conf:
Code:
Section "Device"
Identifier "Configured Video Device"
Driver "vesa"
EndSection
[Code].....
I was messing around with the screen orientation and thought it would be funny to orient it sideways. Big mistake The screen went black.I can force a shutdown, login and I get the same black screen. I tried hooking up an external monitor and the monitor showed no input so I'm guessing my laptop doesn't have that capability with Fedora.This is my main computer.
View 14 Replies View RelatedI am having problems getting my external monitor to work. When I plug in the monitor, both the laptop screen and the external monitor go black. When I unplug the monitor, the laptop screen works again.
When I startup with the external monitor plugged in, neither screen works or teh computer hangs or something.
I have had the external monitor going on a couple of occasions. I did manage to configure my monitors through System Settings > Display. I turned off the laptop monitor as I just want to use the external. But after rebooting, things didn't work.
I have a Thinkpad E420, Fedora 15
So this is really weird - my Logitech headset that I've been happily using with Fedora since Fedora 10 has suddenly started freaking out Fedora 14. Everything was fine until last night, I was listening to some music and it was getting late so I decided to switch to headphones. It was ok for half an hour then, when I think I (maybe, I can't be sure) knocked the USB plug in its socket, Fedora just froze. No coming back.
After a minute of plugging, unplugging, various attempts to get out of Gnome, etc. I gave up and held down the power button. Machine came back fine, I shrugged thinking it was 'one of those things', plugged in the headset again and *bam* - instant freeze! Weird. It's never done this before.
So I restarted *again* - this time plugged the headset in a different socket, same problem. Fedora froze as soon as I plugged it in.
Looking at the logs, here are some excerpts up to the crashes, in case they help. I think this is the lead-up to the initial crash code...
Again, right after those lines Linux froze and the log just tails off.
What's even weirder here is there doesn't seem to be any consistency, a repeating pattern before the crash - but it is always the instant I plug in my headset.
I'm using Debian-Squeeze, and the command "uname -a" results in "Linux debian 2.6.32-5-amd64 #1 SMP Sat Jul 24 01:47:24 UTC 2010 x86_64 GNU/Linux". The desktop environment is Gnome 2.30.2.
My problem is wireless connection causes the system to crash. Here is the detail: my university uses a WiFi service that we have to enter our ID and password in a certain web page in the browser to get access to the Internet, while the WiFi signal is automatically picked up. My laptop crashes each time I connecting to such wireless network. But back home, when connecting to my own WiFi, everything is all right.
As the only thing I can do when such crash happens is to press the power button to force the computer to shut down, I've gathered no more information till now.
Does anyone know what's wrong and how to fix it?
Well, that's about it - the firefox and thunderbird packages included on the first batch of official 13.1 updates keep crashing when I try to print a web page or an e-mail. Seamonkey, updated as well, can print as usual.
View 14 Replies View RelatedMy server is running Red Hat 4.1.2-44.I am having an issue with it hanging (website doesn't respond, can't connect via SSH (it's a remote server)) after 4am on every 3rd Sunday or so.A reboot is required to get the server responding again.I have checked every logfile I can find and found nothing that helps me. The thing I have noticed is that some of these log files start afresh after the reboot so my initial thoughts are that it is a logrotate issue or something similar.
The last activity I can find before the reboot (at 8:32) is in the logfile /var/log/cron:
Mar 28 04:22:01 crond[9356]: (root) CMD (run-parts /etc/cron.weekly)
Mar 29 08:32:39 crond[3884]: (CRON) STARTUP (V5.0)
[code]....
My Epson CX6000 works fine except it only prints in black whether I'm using image viewer, gimp, etc. It's been like this for some time, but I didn't need to print anything in color until now. I'm using Hardy Heron 8.04 and I didn't have any trouble installing the printer.
View 2 Replies View RelatedI can't seem to get Ubuntu to run on my old Dell Dimension 2300. It boots to a purple screen then it goes to a black screen with a load of writing nothing else happens after this screen. [URL] Could someone advise how I can get it to work?
View 1 Replies View RelatedI turned on my Acer laptop and during bootup it seemed normal. After it passed the blue Acer logo, all I could see is a black screen and a black cursor outlined in white in the shape of an X. Thinking it would be a one time thing, I turned it off again.it still was a black screen.
View 14 Replies View RelatedI have an Emachine that my uncle gave me and I thought that Ubuntu would find a nice home in the cozy case and well.....
I have a Emachine el1200-05w AMD Athlon 64 2650e / 1.6 GHz NVIDIA GeForce 6150 SE 2.0 GB mem. and 160GB HDD
I had to fight to get it to install kept freezing and stopping. I finally got it installed. It runs fine and is fast. I like it alot and then after about 5 to 10 min. The screen locks up or will distort in multicolor stripes across the screen. I cant figure out whats going on!
I did just notice that the specs say it's a 64bit possessor and I'm running the 32bit ubuntu will that make a difference?