Ubuntu Installation :: Won't Install On Nvidia Sata?
Jul 7, 2010
I've been trying for a couple days to install Ubuntu 10.04 on my desktop after using for a couple months on my laptop.My desktop has an Asus M2N32-SLI mobo, with a single 100GB HDD.I currently have Win7 installed and have resized the partitions using gparted from within the Ubuntu LiveCD.When I start the install from the icon on the desktop it goes until it asks where to install and then it doesn't show any drives at all.Most of the things I see pertaining to the nvidia chipset and HDDs talks about RAID. But I am not running any kind of RAID. Just a single HDD.
I can't figure out how to install the nvidia drivers for my nvidia 8800 GT video card. I've followed some other posts and all the posts seemed either incomplete, or led me down a path of which eventually broke my installation, that I needed to reinstall the entire ubuntu system.Again, it may not have been broken, i just didnt know how to get back in to the gui version of ubuntu, the instructions took me to the console terminal
1.) I've installed the ubuntu 10.10 64bit for i386 in an oracle virtualBox..
2.) downloaded from nvidia.com "NVIDIA-Linux-x86_64-260.19.44.run"
I'm trying to install 10.04b2 x64 on my new rig and for some reason the live cd can't detect both of my 1TB Sata 3 drives. There is no Raid and the bios has them flagged as IDE. I have also tried adding pci=nomsi to the boot string to no avail.
My computer has 2 HDDs attached to 1st and 2nd SATA ports of my mobo respectively, the 1st SATA drive is empty while the 2nd have my Windows Vista on it. I also have a Perc/5i RAID card with 2 RAID arrays defined.
I am going to install Ubuntu 10.04 x64 to the 1st SATA driver (I expect it will be /dev/sda), but when I try to install, I found my drives are recognized as below,
/dev/sda > 1st RAID array of my Perc/5i /dev/sdb > 2nd RAID array of my Perc/5i /dev/sdc > 1st SATA drive < I need to install ubuntu on this drive /dev/sdd > 2nd SATA drive
I don't want to install 10.04 as /dev/sdc because I may add more arrays to my raid card which from my experience of 9.04, it will probably change the drive letter of my current /dev/sdc and then system will fail to boot.
Is there any way to force my 1st SATA HDD as /dev/sda during install ?
I keep getting this error in my log viewer every 2 seconds: Code: ata4: limiting SATA link speed to 1.5 Gbps I have a dual boot SSD and I have run many SMART tests in windows and linux, (using smartmon tools and the disk utility) and the reports are all 100% healthy..... My research shows that this error represents one of the following:
1. Problem with SATA controller 2. Changing BIOS to allow SATA 3. Changing SATA mode to PATA or AHCI 4. Replacing the SATA cable 5. Allowing the SSD to run at SATA II speeds, i.e. 3 Gbps
- Does anyone know how to try number 5, i.e. allowing the SSD to run at SATA II speeds? I am lost here and this problem has caused my machine to crash twice when watching a movie in linux/ ubuntu. (It is worth noting that the crashes have only occurred in linux and I have never had an issue in windows, so it does seem to be a linux setting somewhere, hence why I think it is a "allowing SATA II to run at correct speeds issue")
ubuntu 8.04 server can not detect seagate sata hard drive 2tb or sata Lg dvdrw x22 sata drive .is it possible to install it without buying a pci ide sata card?is it possible to get a driver for sata driver and sata drive that can be recognise by ubunto 8.04 server ?or to get the files for 1.44 floppy diskdoes the late edition of unbutu recognise sate hdd and sata cdrw drive automaticly during the installation of the unbutu?
I had Ubuntu 8.04 installed on server#1 and moved it to server#2. Everything works fine, including the changing of eth2/3 back to eth0/1. I was wondering if it's possible to use the nvidia onboard raid and make a raid 1 with this OS not getting wiped out. It's a bios level cheesy raid and it warns that it's erasing the data (which is didn't erase), but wont boot anyway. I'm assuming it's probably best to just create a software raid in the working OS with a fresh 2nd drive.
I have REHL 6 Desktop. I have a macbook pro 7,1 with nvidia graphics and (I believe)a nvidia sata controller. I have fedora currently installed with no problems during or after installation ( with a few drivers of of course).
When I boot with the disk i burned ( works on other computers) it comes up of a list of devices to select and when i select local CDROM or DVD it goes to select drivers. So, then I tried "burning" the installation files to an external hard drive then I used the DVD to boot and selected Hard Disk then selected SDB1 (path of external HD). With this method I get to the Graphic installation screen and can go to the part were it says custom partitioning. I select ok then it say the only disk that is available is SDB1 (EXTERNAL).
I installed Ubuntu 10.04, and happened to have an Silicom Images PCXpress card plugged in, and it kindly added the sil_sata module.This is fine for this chip set.I think that my earlier installation of Ubuntu 9.04 used Libata, which does support NCQ and also has good legacy support for the Intel Intel ICH7 chipset I have inside my Sony Vaio SZ notebook. Also, libata also support Silicon Image chipsets as far as I can tell from URL...I wish to remove the Silicom Images SATA modules and replace this with libata and then test the performance between the two device drivers.
Code: debox@debox-htpc:~$ sudo apt-get install nvidia-glx-195 Reading package lists... Done Building dependency tree Reading state information... Done
The following NEW packages will be installed nvidia-glx-195 0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded. Need to get 0B/19.8MB of archives. After this operation, 61.2MB of additional disk space will be used. (Reading database ... 129752 files and directories currently installed.) Unpacking nvidia-glx-195 (from .../nvidia-glx-195_195.36.03-0ubuntu1~karmic~nvidiavdpauppa2_i386.deb) ... dpkg: warning: obsolete option '--print-installation-architecture', please use '--print-architecture' instead. dpkg-divert: `diversion of /usr/lib/libGL.so.1 to /usr/lib/nvidia/libGL.so.1.xlibmesa by nvidia-glx-195' clashes with `diversion of /usr/lib/libGL.so.1 to /usr/lib/nvidia/libGL.so.1.xlibmesa by nvidia-glx-185' dpkg: error processing /var/cache/apt/archives/nvidia-glx-195_195.36.03-0ubuntu1~karmic~nvidiavdpauppa2_i386.deb (--unpack): subprocess new pre-installation script returned error exit status 2
Errors were encountered while processing: /var/cache/apt/archives/nvidia-glx-195_195.36.03-0ubuntu1~karmic~nvidiavdpauppa2_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1) debox@debox-htpc:~$ No idea what's going on here, dpkg is broken?
I am trying to install Ubuntu 10.10 desktop alongside windows 7 on my 2TB Nvidia Raid 0 HDD's but when i select where to install the OS on the ubuntu installation it sees through the raid and only shows the HDD's and no partitions. is there any way to install ubuntu without having to take off Raid?
Being a total beginner to linux, I can't seem to find a decent guide on how to install these drivers without much hassle, even though I've been searching for almost couple of hours now.
First, my system specs, taken with Hard Info Processor: 2x AMD Athlon(tm) II X2 240 Processor Memory: 3091MB (1865MB used) Operating System: Ubuntu 10.04.1 LTS
-Display- Resolution: 1360x768 pixels OpenGL Renderer: GeForce GT 220/PCI/SSE2 X11 Vendor: The X.Org Foundation
Now, I've installed the "default" (dunno if that would be the correct categorizing) driver with the "Hardware drivers" utility from System->Preferences->Hardware drivers because I've failed numerous times trying to install the package from nVidia site ; I would always get an error while trying to run the package : "It seems that X server is running on your linux, please deactivate it to install this package" or something like that, but I'm sure it was about X running.
I recently downloaded and installed Ubuntu 10.10. I thought it was awesome...still do. OK, the problem is i was prompted to install some proprietary drivers and so i did but thats when the problems started. After reboot i couldn't get the GUI or gdm (not sure what to refer it to) to work. It goes directly to a terminal screen every time so i actually reinstalled Ubuntu and tried installing the drivers all different ways but no luck. i also can get into recovery mode and do low graphics. the driver version im trying to get working is nvidia 260.19.12. my graphics card is a geforce 7 series cant remember the number i have a 32bit processor.
Installed Ubuntu 11.04 but i don't know how to install my nvidia 7200 gs graphics card. in the previous versions (ubuntu 9.10) it installed very easly.. But in Natty 11.04, while i am try to install my driver it fails 2 times and after installation (reboot) ubuntu freezes and not working So reinstalled ubuntu 11.04.
My motherboard supports SATA but I do not know which version: SATA-I or SATA-II. I want to buy a SSD so it would be pointless to buy a fast SSD if my motherboard only suports SATA-I
Only about 1.5 weeks into Linux guys so bear with me. I'm trying to uninstall the Nouveau driver and install NVIDIA-Linux-x86-71.86.14-pkg1.run for my old Nvidia TNT2 card. Following these directions I run into a problem in the first step. When I execute the Ctrl+Alt+F1 command and get:
Ubuntu 10.10 splat-desktop tty1 splat-desktop login: if I enter splat which I believe is my username and the correct p/w I get an incorrect login response.
Lucid installed without any errors that I can see of off the main i386 installation CD, but after booting I get no display. Even in recovery mode. The monitor doesn't go into sleep mode and I can tell that the OS is actually running the background because I can do a Ctrl-Alt-Del and do a proper shutdown. I'm running an nvidia GT 9500. Everything is working fine on Karmic.
I'm trying to install the current drivers (from the Hardware Drivers tool) but it fails, refering me to jockey.log, which contains this:
Code: 2010-05-23 16:19:46,978 DEBUG: nvidia_current is not the alternative in use 2010-05-23 16:19:47,106 DEBUG: nvidia_current is not the alternative in use
I've been trying to install the latest driver NVIDIA-Linux-x86_64-256.35.run. I do ctrl+alt+f1 and login, then sudo sh ./NVIDIA-Linux-x86_64-256.35.run and it gives me the license agreement, but after I accept and right after it gets to 100% it says it can't install the kernel or access or whatever. Has anyone done this installation and had the same problem but figured it out??
I've seen may similar issues to mine, but some are different and others are identical, but have been resolved since in the repositories. I install Maverick from CD, reboot, update via update manager, reboot, install nVidia driver via additional hardware gui, reboot and I can't get into X, I get tty1 instead with a text login prompt.
dmesg tells me: Code: nvidia: probe of 0000:01:00.0 failed with error -1 purging nvidia-* and deleting /etc/X11/xorg.conf means that I can get back into X, but without any hardware drivers. I have both an onboard and PCI-E nVidia graphics adapters but my PCI-E one is primary.
It's been quite a run-around trying to get the Nvidia driver working.I have already followed a lot of instructions, at least onceI still get caught at "the pre-install script failed". When I looked at the script itself, it says it's "triggering an error status to prevent the installer from overwriting ubuntu's nvdia packages."Some say this script can be ignored, but it seems to be the only thing keeping my install from working.Some say install from root prompt, some say GUI OK. Some say d/l from NVIDIA, some from repository. I have been doing root, init 3, removing old drivers, etc..
I am currently with Wubi 10.04 under Vista and my Dell XPS 630i has a 1 TB Nvidia RAID controller.First image (Option A) suggests /dev/sda as device for boot loader installation, while second image (Option B) suggests /dev/mapper/nvidia_bcidhdja.I think that the way of keeping the RAID would be using Option B as the device for boot loader installation. Would Option A break the RAID instead?
I have Ubuntu 10.10. I want to install the from the nvidia website. The propriatary drivers from Ubuntu aren't great. I have downloaded the file, but what do I do with it now? How can I get it installed?
This was my first experience with Ubuntu, I was told to switch the hard drives on my computer and put the Windows drive in a safe place for the install. The first time I did the install on the hard drive (which was the clean second hard drive that came with my computer), I either didn't realize I believe I didn't realize I had to click a button and thought the install had gotten stuck, and therefore cut off the install midway through. The second time around the install went without a hitch, and I was able to boot to desktop once. There, I was notified that I needed/should install NVIDIA drivers, I believe version 173 was listed as the next most recent drives (the other was "current"), I have an NVIDIA GeForce 7350LE graphics card, and after installing the drivers, I went to the restart menu as directed and clicked restart, not shut down but restart, and there were several listed errors on the text/DOS screen, shutdown errors I believe (the errors were 5 digits and were something like 56759 or something like that, I can't be certain if I'm remembering right, though, but there were two errors going over again). I then proceeded to turn off the computer manually, and upon it coming on again, instead of the normal Ubuntu flash screen before login, a more choppy Ubuntu 10.10 screen popped up and it led me to the DOS mode, where I was able to login, but it did me no good because I don't know command logic for Ubuntu. The best I did (its the best I ever do when these things happen) is get menus to pop up that are basically useless. I turned the computer off and on again three times, and tried booting directly from disk, but that failed.
I'm actually using the same computer I just reinserted the Windows drive back in after the frustrating experience. Windows has been giving me problems itself, and I really wanted to switch to Ubuntu but I need to know that this is a fluke and not the norm. I can live with this sort of thing being so uncommon I must have did something that was very strange and out of the ordinary to my computer. But if its commonplace, I want to know that too, because that's just something I can't live with.
I realize that many have had the issue of getting a black screen when booting up. I'm posting because I've tried a couple fixes that I read after doing a search and haven't had any luck yet. I have the 64-bit 10.04 installed on my netbook and my issue surfaced after installing the current nVidia accelerated graphics driver. Following the install ubuntu now boots to a black screen and nothing more. 'nomodeset' only allows me to boot ubuntu in low-graphics mode (which I'm in now) and this fix hasn't produced a solution either: [URL]..64&postcount=9 My netbook has nVidia ION2 graphics with an integrated as well as a discreet graphics card (Intel GMA3150 and NVIDIA GT21
This is to request the communities assistance with the following: As the title suggests, I am attempting to install 10.04.2 LTS on a PC equipped with an ASUS M2NPV-VM mobo and integral NVidia GeForce 6150 chipset/card and AMD dual processors.
Result: While the CD with the installation software loads, the splash screen comes up distorted and is displayed as several black and white horizontal bars. I have tried this with low end monitors with a VGA input with the same results. It appears to me as if though the video driver on the installation CD is not suitable for the mobo's chipset, but I may be wrong.
I've often installed Debian Netinstall and added the nVidia driver for my monitors. I just purchased a new PC that has this as part of its description:AMD A4-5000 APU with Radeon(TM) HD Graphics..I have monitors connected to both its analog and digital outputs. Larger distros have enabled a good video driver automatically, but I need to know how to do this for my Debian Netinstall partition. The video performance is horribly slow right now.
I've followed leigh's installation instructions for the nVidia drivers on Fedora 14, and everything seemed to go smoothly, but I don't see any obvious changes after rebooting (should I?).When I go to KDE's KInfocenter (KMenu -> Applications -> System -> Info Center) and check the driver information I see this:
