Ubuntu :: Installation Of Radeon HD 4670 Has Failed
Jul 7, 2010
I tried this: [URL] to install my Radeon HD 4670's graphical drivers but it actually didn't work. I rebooted my computer and it says that the driver is not found and it makes the OS run on low graphics mode. I'm pretty new at Linux and running Ubuntu 10.04 Lucid Lynx. I'd like to know either how I could make my thing use the default driver for my card (with which I was able to put the extra visual effects...) or how could I install the thing properly...
I want to get Debian stable working on an iMac 11,2 (previous model):
1/ Same problem as this one, but I solved it by installing the fglrx-driver 2/ New problem: magic mouse and wireless keyboard don't work - solution: install .38-kernel from backports 3/ New problem: fglrx for .38 requires linux-headers.38 requires linux-kbuild.38...
So again stuck with the vesa-driver. I'm quite happy with the wireless mouse and keyboard working, so I'd rather stay with linux-image.38.
Two possibilities: 1/ I get the radeon-driver working 2/ I get the fglrx-driver working
I'd prefer the first method, but as you can see in the log (infra), there's a version mismatch between the kernel and the radeon-module. Any ideas how to get around this?
Using the radeon-driver gives me the following EE's in xorg.0.log.old: (EE) RADEON(0): [dri] RADEONDRIGetVersion failed because of a version mismatch. (EE) RADEON(0): Acceleration initialization failed (EE) RADEON(0): clock recovery failed (EE) RADEON(0): channel eq failed (EE) GLX error: Can not get required symbols.
The las error is also shown as the only error when I use the VESA-driver; so clearly that is not the problem. I have tried without an xorg.conf, and the following xorg.conf won't work either: Section "Module" Load "glx" Load "dri" EndSection ..... I also tried the radeonhd-driver, but that doesn't change anything.
Whenever I try going into "Desktop effects" it says: Accelerated 3D graphics is not available Desktop effects require hardware 3D support. I'm guessing this is a driver issue? I tried installing a driver for it, I think it was Catalyst but it didn't really work.
The 3D acceleration of my Radeon 4670 doesn't work and I want to fix it. I have installed the drivers like in the sticky explained and also tried it one time with disabled AIXGL and Composite. I use Fedora 13.
Here are my "xorg.conf", the "LIBGL_DEBUG=verbose glxinfo" and my "Xorg.log" xorg.conf: # Xorg configuration created by livna-config-display Section "ServerLayout" Identifier "single head configuration" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" EndSection .....
Xorg.log: But it seems like it can't be opened... (WW) warning, (EE) error, (NI) not implemented, (??) unknown. [ 30.323] (EE) fglrx(0): Cannot shmat() low memory [ 30.323] (EE) fglrx(0): em) error: Permission denied [ 31.984] (EE) AIGLX error: dlopen of fglrx_dri.so failed [ 31.984] (EE) AIGLX: reverting to software rendering
I just updated my box to 11.3. And now when it starts, it goes to runlevel 3 which means the X server is not working. I'm using Radeon HD 4670. How do I configure X from runlevel 3?
I bought this Radeon 4670 [URL] to improve my video. Although the description on ATI-AMD webpage [URL] specifies that this card can output up to 7.1 audio through HDMI, Sound Controls only shows the stereo and off option. ATI Catalyst does not have any controls for audio. Is there a way to get 5.1 audio enabled? Using 10.04.
I tried to install the driver using the easy and hard way, but unfortunately I couldn't install it. When the file manager opens up through terminal after I type in the command using super user mode, I select the downloaded file and it opens it up in kwrite.
I recently bought a HIS HD 4670 IceQ card but can't get it to work in openSUSE 11.2 Under Windows the card works fine, so I assume there is no hardware problem. I tried this card in two computers with different mainboards, but it does not work. Several times I reinstalled openSUSE completely from scratch (tried both 32bit and 64bit versions) but no luck. The problem: Right after the installation it uses the radeonhd driver. This basically works, but without 3D (no Tuxracer...) and even 2D is slow (dragging around windows on the desktop is slow, page scrolling in firefox also).
Then I tried to install the ati proprietary driver, both from rpm (the rpm's from the "official" ati repository have a checksum error, as already mentioned in another thread!), and by downloading the driver from AMD and running the install script. The install script seems to work successfully. The kernel module is compiled and loaded. "aticonfig --initial" makes a rudimentary xorg.conf. But then, when starting X, it does not work:
- on one of the 2 tested systems, even kdm does not start, the screen simply stays black with a frozen cursor top left, even CTRL+ALT+backspace doesn't do anything - on the other system, kdm starts and shows the login screen, but when trying to start KDE kwin crashes, and the windows have no title bar (when I googled for this symptome I found lots of people also having this problem...) - trying to configure the system using sax2 didn't help, even sax2 doesn't display properly I have now spent 4 days trying to get this to work and now I'm really tired of those buggy graphics drivers, be it proprietary or open source...
Can anyone recommend me a graphics card that is approximately as powerful as the radeon 4670 (I bought this card because it is said to be the most economical card (both in price and energy consumption) that allows to play Anno 1404 reasonably well on windows), but is known to work in openSUSE 11.2, even in 3D mode (tuxracer...)?
I (somewhat foolishly) decided to reformat windows XP and make my foray in the Ubuntu world with Ubuntu 10.04 Lucid just last week. It has treated me fairly well so far and with the help of others posts have been able to get most everything setup to my liking. However...My Problem:I tried to install the ATI drivers for my radeon 9700 using ati-driver-installer-9-3-x86.run. I tried to install it using the Ubuntu/9.04 settings, hoping that I could get it to work like that and I was quite wrong. When I restarted my computer I was started in simple graphics mode, and now I'm trying to set things right again.'ve un-installed the fglrx drivers (I think...) and now I'm stuck. Play On Linux tells me that I need to install 3D acceleration, something I know my graphics card has..
I have an older computer and I did a fresh install of Jessie
Procesor AMD, Graphic card ATI Radeon 9200 PRO / RV280
After instalation my computer boot into black screen. I have no problems with wheezy.
I installed manually firmware-linux-nonfree (in case) module R200_cp is loading correctly.
When I configure Xorg, my log file says something like that: ----------------------------------------------------------------------------------- (EE) Segmentation fault at address 0x0 Fatal server error: (EE) Caught signal 11 (Segmentation fault). Server aborting --------------------------------------------------------------------------
Fedora 12, Kernel 2.6.33 stable. When i compile this kernel with radeon and KMS enabled i get the following:it take a whole minute for it to fall back to non kms setting, but what worse is the it won't find the damned firmware. i have this bin file almost every directory (/lib/firmware(redeon)) have in the the main source tree of the kernel before compiling and after. i tried to build it into the kernel (ext_firmware) blobs but no F...ing luck.
i've googled all night alongside compiling new kernel with diff settings (10 hours O.o run ) and no luck... there was something on mailing list the they are not going to include this firmware in the kernel ever(only git or something) and placingfirmware into the appropriate directory should fix everything.On the side note: i had Arch linux installed just recently (dont ask why i have swithched arch was perfect but: not LSB , thus ..well doesnt matter) nad i had 2.6.33.rc8 installed with KMS and all was freaking perfect... it had no problem finding that stupid firmware..
I installed openSuSe 11.4 on a Lenovo W500 and noticed this error message upon bootup. The desktop login doesn't make it to the screen. I went into fail-safe mode as root. I know the issue is attributed to the R600_rlc.bin located in /lib/firmware/R600_rlc.bin. I attempt to make some config changes but the file is in binary. It could be a problem associated with the creation of the initrd but not certain. It's a dual-boot system running Windows 7 on the other partition
I replaced an ATI Radeon 9550 with a Radeon X1300/X1550, in hopes of better performance.
My System: P4@3GHz, 1.5Gb RAM, Fedora 12, kernel 2.6.32.10-90.fc12.
Faults: Screen refresh is extremely low. Glxgears outputs 25 FPS. Dragging windows around is sometimes really slow.
What I did so far, in hope of fixing it:
1. Installed 'system-config-display', for providing an xorg.conf 2. Did: yum --enablerepo=rawhide update mesa-dri-drivers-experimental mesa*, fixing this, but to no avail...
I cannot find any errors in the log...I don't know what to do...
I am posting my Xorg.conf, Xorg.0.log and Glxinfo through links to pastebin.com
POST UPDATE:
When running GlxGears, I get a bit of motion, and then the gears freeze for 1 second. And this goes on and on. But...if I move the mouse around, I get 1100FPS!
Now I messed a bit with xorg.conf and the "SWCursor" Option, but the above happens when this option is on "true". On "false" there is no 1100FPS, only the freezing loop...
I been searching for months on how to get the s-video to work on my pci VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] card. I found a site with instructions.
This is how I got it to work.
I install Debian 5.0 Lenny Desktop
added the Driver "radeon" to my /etc/X11/xorg.conf file
This work and I was able to use my tv as a monitor however when I try to play a video file from totem or vlc all I could get was audio with no video; These files work and played fine in the CRT monitor.
I have configured the remote installation of Fedora 13 with kickstart with nfs installation method. All work ok until I boot the Fedora 13 client system.
Fed13 client system receives the IP address from dhcp, receives the loader, loads vmlinuz and initrd.img from tftp, load anaconda, configures the network and dev eth0, mounts nfs server to load kickstart file, loads kickstart file (language...) but when it tries to mount nfs server to install from Fedora 13 installation tree it fails.
First, I thought that I had an error on my NFS configuration but I was wrong. I opened tty with ALT+F4 on the Fedora 13 client and I sew this error:
Code:
Is this a bug or can I modify anything to correct this error? How?
I can't my system because of this error: Code: linux-firmware: /lib/firmware/radeon/R700_rlc.bin exists in filesystem Note that in the beginning, it asks:
Code: :: Replace kernel26-firmware with core/linux-firmware? [Y/n] There are so many updates by now that the list fills in a few pages in the terminal! Also, I wonder why so many Arch updates get stuck or broken compared to almost any other distro? Is it poorly designed packages? Is it a design flaw in pacman/the package format?
From looking at beaucoup posts, it appears I'm SOL trying to use the Linux drivers provided by AMD (See url.terminal command line "sh ./ati-driver-installer-9.2-x86.x86_64.run". Since I keep getting an error message saying the file can't be opened either as root or using sudo I guess there's no reason to continue.Anyway, I have my PC displaying on a CRT thru a s-video connection. The screen is overscanned, that is, part of both the left and right sides are not visible. That is why I wanted to load the Radeon drivers & Catalyst Control Center so I could shrink the screen width.Question: Should I keep trying to open the ATI file? SHould I install the Open Source ATI driver? Should I give up and try to find a nVidia AGP 8X card?
When I put my laptop, a Presario X1000 to sleep that uses Radeon Mobility M7 LW [Radeon Mobility 7500], when it comes back up, I get just black and white "nosie" on the screen.
Even after I do cntr+alt+F1 and then cntrl+alt+F7 it still doesn't appear to restore the regular screen.
I upgraded my HP Elitebook 6930p from 9.04 to 9.10. When X starts the display shows random lines. I can boot into "recover" mode from GRUB and get the command prompt. 9.04 worked fine so I'm pretty sure it's not the video card. The video card is ATI Radeon HD 3400.
So far everyone thats tried to help has mentioned modifying xorg.conf On this installation, there is no xorg.conf file. Anyone with video troubleshooting experience with ubuntu 9.10 ? I cannot even get 800x600 16 colors displayed correctly
I've always had and used Ubuntu. When I installed and did not like the stability of a certain version, I just reformatted the partition and used LiveCD. OK, on a virgin SATA, 300-gig partition, I installed 10.04 and that took the ATI Radeon 3rd-party graphics driver. No problem. Then, the family wanted 2 languages on the machine. The German keyboard screwed me in terminal and I wiped out Home and all their data. I used Scalpel to image-carve 300-gig onto a 400-gig partition and tried to re-install Ubuntu 10.10.
The ATI's fglrx will not install, that's the error. That same file prevents upgrades of Ubuntu to current status.
is this thread current for my problem with 10.10? http://ubuntuforums.org/showthread.php?t=651566
Or, do I have that 400-gig with the backup cross-pollinating?
After upgrade to Lynx, all of my ATI drivers don't work. Whenever I try to run fglrxinfo I get " Segmentation fault " And for fgl_glxgears I get" Using GLX_SGIX_pbuffer Segmentation fault " For sudo aticonfig --initial -f " Uninitialised file found, configuring.
Using /etc/X11/xorg.conf Saved back-up to /etc/X11/xorg.conf.fglrx-11 " Compiz does not work at all either.
I can't get kde to start. I boot through the blue ubuntu 10.04 splash screen normally, so my video card is putting out something, but then i drop into a tty terminal. I log on ok, but when i do startkde from the command line i get a message saying can't connect to xserver, when i do startx, i get these errors: (i can't stuff them here cuz i don't have a mouse or a cut and paste ability)EE) NVIDIA:
Failed to load the NVIDIA kernel module. . . EE) No drivers available.
But here's the backstory: I have a ASUS M3N78 PRO MB with an on board Nvidia GeForce 8300 graphics capability. It was intermittently failing, so i disconnected it put in an ATI RADEON PowerColor HD 3450 graphics card, and then my problems started. Seems to me I must have the Nvidia driver since i can boot to KDE fine using the Nvidia onboard analog output (at least some of the time).
Supposedly Lucid Lynx has the ATI drivers for my card preinstalled, plus the new card does drive the splash screen. Is there some clash in some script between the Nvidia on the MB and my ATI Card? I upgraded to GRUB2, reconfigured xserver-xorg, tried to run jockey from the command line and failed, tried sudo nvidia-xconfig. Nothing changed anything.
I just finished building my new machine. I've got windows 7 running just fine on it, but I wanted to dual boot Ubuntu 10.04. I downloaded the 64 bit iso and tried installing it from both a live cd and a usb drive. When I boot from either (cd or usb), I see the Ubuntu loading/boot screen, but after the data is loaded, my display goes black and seems not to be able to find a signal. I assumed initially that it was probably due to the fact that I was connecting to my tv by HDMI cable. I guessed that Ubuntu did not have HDMI drivers for my video card, ATI Radeon HD 5750, by default. Then today, my new monitor arrived and I switched to the DVI output on my video card. I assumed that this would allow me to boot and install. I was wrong. I experienced the same symptoms on my monitor via DVI as I did on my TV via HDMI. why my monitor drops the signal as soon as it leaves the loading/boot screen?
I am new to Ubuntu for the most part, but have done a lot of research on this OS. I just freshly installed version 10.10 32 bit, and the first thing I did was follow this tutorial on installing the drivers for my HIS Radeon HD 6850. I really want to get this drivers working so I can use the 3D effects on this OS.
When I type fglrxinfo I receive:
X Error of failed request: BadRequest (invalid request code or no such operation) Major opcode of failed request: 136 (GLX) Minor opcode of failed request: 19 (X_GLXQueryServerString) Serial number of failed request: 14 Current serial number in output stream: 14 When I type aticonfig I get:
aticonfig: No supported adapters detected. The proprietary driver was never installed so I know that driver is not interfering. Originally the aticonfig was not found at all but with a little troubleshooting from the link above It seems to work, but obviously not recognize the card. The card works great on my windows 7 setup. If I can't get this working I may just remove Ubuntu all together, but any help would be amazing!
Card is the Radeon x300 and in the past in a wubi install I installed the propreitary ATI driver. I'd like to do that with this installation too. I've located the proper driver and tried to run in the terminal.
I get this error:
I've read were I have to uninstall the xorg drivers and make a .deb package but idk how to do that.
I've just installed 11.04 but can't have unity since it doesn't support ATI Radeon HD 5600 series along other ATI cards. Anyone who knows when ubuntu is planning to solve this problem?
I have now installed a radeon 9250l display board. I followed the Ubuntu Radeon documentation page. It tells me that 3d is supported. I am not sure that 3d is correct or running. I am running without a xorg.conf file and my current resolution os 1024x768 (which is fine). I get no errors on boot but want to make sure its correct. I also did:
[code]...
Since the documentation seems to apply to the previous version (mine is 10.04) that may be a problem.
