Ubuntu Installation :: Laptop Runs So Hot Sometimes Gets Sluggish And Locks Up
Feb 19, 2011
Since support for 8.04 LTS will be ending soon, I decided to move up to 10.04 LTS. On my old Thinkpad A20m laptop, the install went well, and everything seemed to work except the middle trackpoint button. Fixed that easily by editing a conf file. Then I began to notice some problems; all power management options (suspend, idle timers, etc) have no effect. I checked the startup logs and it seems that ACPI was not loading due to my aged bios (yes it's the newest version available). I tried using acpi=force in the boot options, and viola: power management is working. But that made two other problems crop up.
Problem 2: Since using acpi=force, the laptop runs so hot it sometimes gets sluggish and locks up. I tried installing "thinkfan" from
the ubuntu repositories to have some way of easily changing the fan behavior(which I believe relies on ACPI in some fashion). No luck there. ACPI seems to not see my fan at all, and it only kicks on when the bios high temp failsafe is tripped. I should also mention I am using Xubuntu (for the lighter desktop). I'm still kind of an Ubuntu-noob, so I wasn't sure what other info to post.
I upgraded to 10.04 from 9.10 via Update Manager. Upon reboot after the upgrade, I only got as far as the log-on sound and the laptop locked up. Even the power button was unresponsive, so I had to unplug the laptop and let the battery run out to get the thing turned off. I then tried doing a clean install from the CD, but got the same lock-up problem afterwards. I finally had to do a clean reinstallation of 9.10. I am using a Sony PCG-GRT240G Notebook. Are there any steps I can take to get 10.04 to work flawlessly? To get 9.10 to work flawlessly, all I had to do was boot with the noapic parameter.
I have an IBM ThinkPad T43 on which I run Ubuntu 10.10. Everything works fairly smoothly except that I notice my laptop fan runs continuously. When I turn on the machine it revs up until boot-up is complete, then it shuts off for a few minutes, and then it comes back on and never turns off until I'm through working.Is this strictly a hardware problem, or is there something about Linux that causes the computer to run hot and so causes the fan to work hard? Is there a setting that I could check to see if the fan is working properly? I don't use any exotic programs or run video intensive games, so there's no reason why the computer should run especially hot
I have a dell computer that runs kubuntu very nicely. Virtualbox runs in it great and i installed windows xp in a breeze.
My dell laptop however freezes up when i try to boot my windows install cd. I'm running kubuntu on it as well (both run 10.04) and both were just freshly installed with kubuntu.
I just can't boot the cd for some reason. Laptop totally locks up and you have to press the power button for 5 seconds to turn it off.
It's an amd turion 64 x2 dual core processor in my laptop, whereas my desktop is an intel e5200 cpu. That's the only thing i can think of that might require special settings or something in virtualbox. I've played around with all the cpu settings in virtualbox, but every single time, it totally locks up the computer.
My friend recently gave up on Windows Vista on his old laptop and installed Ubuntu 10.10 64 Bit on it. He came over the other day because I wanted to show him and install some cool things. One of those things was a dock. I tried both AWN and Docky. When the dock started running his system became so unbearably slow. Like it took over 5 seconds to respond to movements sometimes. When he closed the dock everything went speedy again. He has a whole lot of compiz stuff running now, including desktop cube/animations burning up windows when he closes them. I'm wondering why the dock is causing such a major slow down.
His specs aren't even that bad. He has a Dell XPS M1330 with the following specs:Intel Core 2 Duo T6400 (2.0GHZ)4GB of RAMNVIDIA 8400M GSMy laptop has very similar specs to his, except my integrated graphics card is an ATI 3200 and it runs AWN and Docky flawlessly. Anyone have any ideas what could be causing this? His graphics card was one of those faulty NVidia cards from back then but he already had it fixed twice and its been running Vista without any graphic issues fine since. I didn't get a chance to look at it again since then so I couldn't play around.. I'm thinking he might have possibly messed something up playing around when he first installed it. I may suggest a clean install and do everything again to see if the problem persists.
it is a macbook pro (5,3) running sid.when i am using it, it is cool.however in suspend mode, it gets very hot.i have this running
Code: Select all/etc/init.d/macfanctld status ● macfanctld.service - LSB: Apple MacBook (Pro) fan control daemon Loaded: loaded (/etc/init.d/macfanctld)
Acer 5250-BZ475 laptop, fresh install of Ubuntu 11.04. Boots up beautifully as long as an ethernet cable is plugged in. Otherwise, I get to the login screen and have just enough time to start typing in my password before the entire system hangs hard - no mouse, no keyboard, can't even get to a terminal, nothing. Have to hard power off the machine.
It seems to be a problem with the wireless card trying to initialize, but there doesn't seem to be a bios option to disable wireless on this laptop, so I'm a bit at a loss as to how to fix this problem. By the way, wireless works fine if I boot up with a cable connected - I can see all the wireless access points in my area no problem. I just can't boot without a wired connection, which makes my laptop more or less useless when I'm away from home with it.
I have been using Ubuntu for quite a while now and have upgraded from 9.04 to 9.10 using the upgrade system.However, I now have an issue with Rhythmbox that wasn't there in 9.04 - whenever I load it the mouse stops working and the light on it starts flashing (it is a trackball).It only happens when I load Rythmbox and nothing else I have come across and happens each time. I have tried uninstalling Rhythmbox and re-installing but it is still the same.I have also searched the forum and googled the problem to no avail.I am using Ubuntu 9.10 on a Intel P4 with 2GB memory, more than sufficient hard disk space spare.
Still having problems with the locked black screen freezing a couple of minutes in. I've done everything anyone has recommended on the other threads but nothing and it is driving me crazy. Please, does anyone have any ideas? I tried to install xfce4 but of course, screen froze and went black before I could fully download the software! I've tried the nomodeset but can't save it before doing a reboot (then went via terminal as quick as I could on start up to edit grub, but then... yes, it fell over and froze before I could hit save). So I'm giving this a lot of time I really don't have... such a shame I upgraded, 9.10 was working so well... alternatively,
I DLed 10.10 iso and burned it to cd. When I try to boot with cd, it starts up fine, I get the Ubuntu logo with rolling dots, but after a few mins it freezes (with logo still on screen). I have been running Ubuntu on this comp for years
I have installed Fedora 12 from the DVD with no apparent issues. It then had me reboot. The color bar goes all the way across the bottom of the screen and Fedora 12 turns white. The screen goes blank and the light is on for the floppy disk. Keyboard does not function and my LCD monitor says no input signal.If I hit esc key while it is trying to boot I see a lot of things being loaded but it is to fast to read what happens last.---------- Post added at 07:31 PM CST ---------- Previous post was at 09:44 AM CST ----------By searching the forum I found that by hitting esc repeatedly I can get to the Grub menu. Once there I edited the command line and added a 3 at the end of the line.I am now logged in as Root.
I've been using Ubuntu for about a year or so and have never had any problems installing it up until now.
I can boot from live CD for 9.10, but if at any point I attempt to install it to my hardrive, it either locks up or the screen goes black. Sometimes I'm able to start the installer, but the screen will go blank. The most progress I've been able to make on the install was up to 98% before it locked up, every other time I've gotten a blank screen or a lock up around 40-60%. After a hard reboot I get an error that reads "DISK BOOT FAILURE. INSERT SYSTEM DISK AND PRESS ENTER"
This problem doesn't only occur with 9.10, but with every other linux distro I've tried on it. My first attempt was with Ubuntu Studio, but I got similar errors. I've searched literally for hours and have found nary a solution that even comes close to solving my problem. using HP Pavilion a404x desktop
I just installed Ubuntu on a laptop that is running windows 7. I accidentally tried installing a piece of software from the software centre before setting up my network. When I boot Ubuntu it now runs in low graphics mode only.
I have a Dell Latitude E5500. For some time I've been installing different distros on it to find which is best suited for my needs. I've tried Ubuntu, Kubuntu, Mandriva, openSuSE, Fedora, and several others. So far, openSuSE takes the cake in terms of what I need, speed, usability, etc. However, I have a soft spot for Fedora and I'm trying so hard to make things work, but I'm kind of at the end of the road unless you guys have some suggestions.
I was in the IRC chat for Fedora asking around, and one user was kind enough to point me in this direction, which made sense as to why I was having issues.
[url]
I was having mixed results, but I had also installed from a Fedora KDE LiveCD. I decided I'd try the full DVD release of Fedora 12 64 bit, so I installed it this evening.
To my disappointment, even the nomodeset parameter does nothing. I get to the blue screen where there's some kind of logo in the center that fills in with white. After it fills in, an F appears. That's where it stops. It just goes no further. Further adding to the confusion is the fact that the fix lists a kernel there, indicating (to me at least) that the kernel listed is when a fix was deployed. I have a newer kernel than that, and despite that I still have these issues.
So needless to say, I'm using my laptop as testing grounds to plop a different distro than Ubuntu on my laptop and 2 servers full time. I really want to make Fedora work, but at the same time I have to use what works for me. Not being able to boot and log in is kind of a big deal. :P
Is there anything I can do or try? I want to keep the OS's I run all the same, so if Fedora 12 bombs out on this laptop, it has no chance on the other servers I plan to run at work. So far openSuSE is running without a hitch but I'd really like to give Fedora 12 a chance....
Recently upgraded Karmic to Lucid (32 bit system).System freezes/locks-up intermittently (seems to be associated with Firefox). Only option is to power off.Have seen other (very recent) posts, many unanswered and none of use.
I tried installing Ubuntu 9.10 using both Ubuntu Desktop CD and the Netbook Remix on a EEEPC 1005HA with an external CD drive.
In both cases I don't get any graphical interface during the installation. The CD is apparently installing everything silently, without letting me change anything on the way, and then it gets stuck.
The only screen I get is the first one, with the options to "try Ubuntu" or "install Ubuntu".
Am running karmic on a P2-350 Mhz with 256 Mb RAM. Yes, I know this is an old computer, but it has been very good, performance wise, since versions earlier than 8.x I think.
But now, after a fresh install of karmic, it is very slow at everything. Checked system monitor and CPU is constantly running at between 95% and 100%
It is a sad day indeed, but I need to run a developer's tool that only runs on Windows, and it interfaces with a USB device that doesn't do well through any VMs I've tried. I've resorted to installing XP.
Now, I'm wondering if there will be any problems I'll face installing XP after Ubuntu 10.04 has already been installed? I suspect so, but it's been a while since I dual booted, and I've never worked with Grub2,
so, I was just upgrading to the new release of Ubuntu and didn`t notice that laptop was running on battery, then it was switched off.Now I can open Ubuntu system, can`t reach to login page.the other two systems are ok, XP and Pardus.how do you think I can recover ubuntu?
I recently installed fedora 9. Everything works fine after install (except sound but thats a different story). When i run updates everything seems to have worked fine but when i reboot afterwards i get to the login screen which works but as soon as i log in it freezes? the only way to restart is to press the power switch...
Sometimes it does this and other times it does not. It has happened with 2 hard drives. When it formats the partition the bar stops and the mouse pointer graphics stops.
I had F11 i586 installed on my X86_64 machine. I used preupgrade to move up to F12. (I had the space problems noted elsewhere, but eventually got all of the F12 packages installed.) Grub now has the following titles:
Fedora (2.6.31.5-127.fc12.i686) Upgrade to Fedora 12 (Constantine) Fedora (2.6.30.9-96.fc11.i586)
If I boot to F12, it boots up to a point where I get garbage graphics and the system freezes. If I boot to F11, SELinux relabels and the system then boots normally. I'd like to boot normally into F12.
Yesterday I downloaded 10.10 desktop version and burned an image to a CD. After installed to a Dell Dimension E510 machine successfully (I wiped out windows completely), the first update found 315 items to update. After downloaded, ubuntu asked to reboot the machine. Since then, the machine is stucking on the ubuntu startup screen. I suppose it is applying the updates; however, it has been over 12 hours. Is it normal to take that long?
I like to keep my pymol molecular viewer as recent as possible. With svn and compiling it used to be easy, up until ubuntu natty. Now I get the following error every time I try to compile:
layer1/Scene.c: In function SceneClick: layer1/Scene.c:4557:11: internal compiler error: in set_jump_prob, at stmt.c:2319 Please submit a full bug report, with preprocessed source if appropriate. See <file:///usr/share/doc/gcc-4.5/README.Bugs> for instructions. error: command 'gcc' failed with exit status 1
This is for EVERY version I have tried. I have even downloaded the source code you can find in the ubuntu repositories (current version for 64 bit is pymol 1.2r2) and tried to compile that one, just as prove of concept. I still get the same error. I think I might need something else beyond what I have already, because if the package maintainers could build the older version for natty, I should be too, with the proper packages, shouldn't I?
It seems I had no say in the matter. The installer automatically did text mode and it starts up in text mode now. I'm very new to Fedora, though I had Ubuntu installed recently but removed it because Fedora seemed a little more interesting to me. I'm on an HP Pavilion dv2807nr laptop if that helps.
I've just upgraded my from F11 to F12 via software update and found F12 extremely slow to the extent that only the mosue cursor moves, the rest does not - not even opening folders or starting application.
My specs: Core2Duo 1GB RAM 160GB HDD
It seems that
npviewer.bin is taking up up to 50% of CPU. Xorg takes 20%..
I am trying to install FC 10 from a DVD. It gets to part where it says "Running Anaconda" and the monitor goes "no signal". I am assuming that the video drivers are incorrect. What can I do to change the drivers before anaconda runs?
