Ubuntu Installation :: Installation Fails Every Time - Message To Reboot My Computer Appeared At The End
Jan 9, 2011
I recently decided to install ubuntu netbook remix 10.10 to my Toshiba NB200. I was using windows and I wanted to completely erase them. I burned the USB, I followed every single instruction the site had, and even though the installation seemed to work, and a message to reboot my computer appeared at the end, the installation finally fails. When I reboot, the only thing I get is a black screen with an underscore at the top left corner. I tried the installation four to six times and even tried older versions as well but all I get is the black screen.
View 9 Replies
ADVERTISEMENT
Mar 29, 2011
I installed Ubuntu 10.10 amd64 (and tried 10.04.2 as well) from Wubi under Windows 7 64-bit. When I reboot after installing it through Windows, I go to Ubuntu and the installation completes. Then it reboots again to finish the install of the OS. When I boot into Ubuntu now, grub does not appear. Instead, some initramfs stuff comes up in a console with no GUI and says some error stuff about root devices. I read that grub updates cause problems, but the installation never finished and therefore I was never able to go into Ubuntu to lock grub packages, etc. I've run into this error on multiple fresh installs.
View 1 Replies
View Related
Jan 5, 2010
At first I tried the using the CDROM to install the server but around 8% through it could not talk to the CDROM anymore. I did attempt this a few times including re-seat the CDROM and it stopped at the same point every time. I then used the Mini install and that worked. However, after I rebooted I received the this error.
Gave up waiting for root Common problems:
Boot args (cat /proc/cmdline)
Check rootdelay
Check root
ALERT! /dev/disk/by-uuid/bfaafj88-83ce-4dd2-8c6f-26o9a869eaea does not exists Dropping into shell:
(initranfs)
I then reboot from this point by issuing the reboot command and can then go into the rescue login with networking. I did select reconfigure GRUB and rebooted but same error as above.
System is an old Dell Poweredge 1550
Ubuntu = 9.10 server
View 1 Replies
View Related
Oct 25, 2010
I am fairly new to linux and my laptop froze so I rebooted it and now I have this error. I have tried to load the files needed using the prompt but nothing seems to work so here is my bootinfoscript thing. Any way for me to reinstall ubuntu over the sda5 partition but keep my files?
Code:
Boot Info Script 0.55 dated February 15th, 2010
= Boot Info Summary: =
=> Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in
partition #7 for /boot/grub.
=> Syslinux is installed in the MBR of /dev/sdb .....
View 5 Replies
View Related
May 18, 2010
I'm installing 10.4 x64 on a Dell PowerEdge R610 in a RAID 1 configuration and the install goes fine until I have to reboot the server to finish the install. On reboot after about a minute it gives the error.We've tried letting GRUB manually configure itself at the end of the install before we reboot and we've also pointed it to /dev/sba partition which is what should be the boot partition.In the code tag it's ALERT! /dev/mapper/mysql(one)-root.... the L and 1 look the same.I've got 3 of these server to get setup and running as part of our back end and network restructuring and have been stuck at this point on the first one since Friday.
View 9 Replies
View Related
Jan 4, 2010
I am trying to upgrade from F11 to F12.Using Preupgrade, everything went well and then it asked me to Reboot. Anaconda started then says something about updating some files then the screen goes blank.
View 14 Replies
View Related
Aug 3, 2010
I am trying to update my OS from Opensuse 11.2 to 11.3 using the installation DVD (checked OK). Everything is OK during the installation process until the message "System is going to reboot" is displayed with a countdown : when the countdown is finished, the screen becomes black and the screensaver starts, but the system does not reboot. When I reboot manually, after selecting "Opensuse 11.3 desktop" on the first menu, the screen becomes black and the screensaver starts.
So the installation seems incomplete and I do not know how to finalize it. When I select the failsafe option on the first menu, it seems to work but some behaviours are quite "strange"... When I choose update instead of installation at the beginning, the behaviour is the same.
I do not know if it is linked but the firmware tests started from the installation DVD show the following errors :
Memory tests are OK.
View 5 Replies
View Related
Feb 26, 2009
I have used the system recovery CD about 5 times on my computer and it wont do anything. I goes through the process but afterwards I go to reboot it and it just keeps restarting itself over and over again. It NEVER makes ot to the windows screen. What can I do to fix this problem? I don't have the money to go to Best Buy to ghave them fix it because I'm broke.
View 2 Replies
View Related
Jul 15, 2011
i have a dell inspiron laptop lap top with windows7 os.my hardisk is 320gb capacity.now i want to install fedora as my secondary os. I tried fedora12 but instaltion terminated abnormally with the message safe reboot needed recievied signal 3. i have 20 gb unallocated space in my disk.
View 5 Replies
View Related
Dec 9, 2010
I installed Ubuntu in my PC alongside winXP. I downloaded the ISO and mounted it using a virtual image software (PowerISO used in winXP). I installed Ubuntu using wubi in a 20GB partition. During installation it asked me how much space should I give, I gave it 11gb. Everything went fine. I rebooted but now the computer hangs during startup. I went to verbose mode to see what the error is and found out that everything is ok. The last line that apears is "Setting sensors limit [OK]" and then nothing happens. I have tried every option (safe graphic mode/ demo mode etc etc) but the computer hangs.
View 1 Replies
View Related
Sep 1, 2011
i am trying to install Ubuntu 11.04 on HP proliant DL 360 G6 but it fails at the time of iso_scan. /var/log/syslog shows "failed mounting /dev/sda" and menu item iso_scan failed i dont know how to solve this problem its urgent. On server RAID5 is configured
View 1 Replies
View Related
Apr 5, 2010
i have installed ubuntu 9.10 on my hp nx6325 notebook, and everything was working just fine, then it updated and problem started coming up. First the computer wouldn't reboot after the update, blank screen, then i manually reboted and now some programs don't work (ubuntu software center, update maneger, avant window navigator)
i assume the update did some damage, so how can i repair this, is there a recovery tool or something.
View 8 Replies
View Related
Sep 29, 2010
i installed the 7zip and ACE for .rar files. But when i want to open a .rar file. computer uses the archive manager. But it fails. i could not open the .rar files. i could not find the 7zip i clicked the right from mouse etc
View 7 Replies
View Related
Apr 27, 2015
When I try to install Debian 8 on my laptop I get this rather odd error. The install fails every time. I've managed to get as far as choosing which Desktop Environment I want and the shortly after it shuts off. It shows 4 messages
Code: Select allSystem is going down!
Sending Termsignal
Sending Killsignal
Requesting Machine Poweroff
The machine I'm trying to install on is a Gateway NV53, 4gb of RAM, AMD Athlon II x64.
At first I thought it might be my disc so I burnt another DVD using the 4.3GB DVD image I had downloaded. I checked the disc and it verified with the image and so I tried again with the same results as above. Any clue what might be causing this? I'm sure it isn't my hardware, Arch has been running fine for almost 6 months and never seemed to care.
View 3 Replies
View Related
Aug 10, 2011
each time i upgrade my kernel, my installation of lirc fails to work after the upgrade, and i have to re-compile (against new kernel) and install the lirc modules... which i do via something like:
Code:
sudo modprobe -r lirc_imon
sudo dpkg-reconfigure lirc-modules-source
sudo modprobe lirc_imon
after which all is well. this of course is a problem that DKMS should solve for me but it doesn't do it. also i get this message in my messages log:
[Code]...
View 1 Replies
View Related
Feb 4, 2010
I've installed 2 different distros on this old dell laptop, install goes fine, i run everything...reboot a few times. perfect, but the next day, when i boot up, i get " date/time" not set, if i choose to ignore that...computer won't boot... is this a battery issue ? the battery wont hold a charge, so i only run it with power pack...works great, but when i turn this on tomorrow, I'll get that w=error messy.
View 4 Replies
View Related
Apr 6, 2010
I am using Grub4Dos to boot Ubuntu 9.10 Desktop Live CD. In the menu.lst i made the following changes.
Quote:
title Ubuntu LiveCD 9.10
find --set-root /ubuntu-9.10-desktop-i386.iso
map /ubuntu-9.10-desktop-i386.iso (0xff)
map --hook
root (0xff)
[Code]....
The code runs fine and Ubuntu loads also from the ISO stored in the C: drive of my system.
The problem is when Ubuntu loads it changes my clock time. I have set the timezone to Indian Standard Time. Since it is live CD it should not make any changes in the system however, it does change the Data/Time of my system.
View 1 Replies
View Related
Oct 30, 2010
I have and acer aspire 5251-1805 and I have a problem to install ubuntu. When I look at the Bios info there are 6 boot options including booting from CD. But then when I start the computer and press f12 there are only 3 options listed and there is no option to boot from the cd. What should I do?
View 5 Replies
View Related
Aug 12, 2010
Recently my beloved ubuntu setup died and I'm struggling to fix it.One day I turned it on and I received the following message:"Your screen graphics card and input device settings could not be detected correctly'Attempting to continue with the recommended lower graphics settings does not work and I am not sure where to go from here. Sometimes it will advance at the lower graphics setting until an error regarding the configuration defaults for the GNOME power manager that have apparently not been installed properly.I didn't change anything and my windoze partition works well. Running Lucid Lynx with nvidia graphics card and ndiswrapper.Other error messages are:(EE) [drm] failed to open device(EE) Failed to initialise GLX extension (Compatible NVIDIA X driver not found)If I reinstall ubuntu will I lose all my programs and data?
View 7 Replies
View Related
May 21, 2011
I have received an ACER Aspire 7720 with Vista and I am trying to install F14. Really I installed it but, when restarting, there were some troubles:
1. Grub did not appeared.
2. Vista decided to loop on start and I could not boot it nor in fail safe mode.So I recovered Vista with an recovery disk, but now I only can start in Vista from HD.
Now I am using a f14 Live CD in order to apply some solutions I have read in the tags but the partitions of Fedora do not appear with fdisk, although I can access them from Live.
View 3 Replies
View Related
Sep 1, 2011
I recently lost the default panel from the top task bar, a message appeared on boot up saying a config file was missing or couldn't load - or something to that effect. I didn't realise to what it was referring until the computer (an Acer One) completed its start up and I could see the desktop
How can I restore the panel? (graphic from my other Ubuntu laptop attached showing the default panel appearance)
View 5 Replies
View Related
Apr 7, 2010
[URL] I used testdisk as the replies suggested recovered all my linux partition including my 2 linux distros and boot partitions, but now my windows 7 appeared as unallocated space, which is very ironic, I fixed my last problem only to have situation reversed. I recovered the mbr record from my boot partition, but because that record dose not include the ntfs partition, that partition appears as unallocated space. so how can I make that ntfs partition recognized again so I can update grub and boot to my windows 7 partition? Please help me out, I have had this partition stuck in my computer for a while doing nothing...
View 2 Replies
View Related
Oct 26, 2010
I'm having trouble updating. Using the update manager fails and I see the message:dpkg: parse error, in file '/var/lib/dpkg/available' near line 23288 package libbonoboui2-common': 'Conflicts' field, reference to 'libbonobous2-0': version contains ' '
I've tried
sudo dpkg --configure -a
and
[code]....
View 1 Replies
View Related
Jan 26, 2010
This system has AMD Turion with ATI HD 3200 Graphics system. Installation program correctly initializes graphics - all installation completes with automatic configuration - gives no option for sax2 to run. Then Suse does not comes up or the x does not comes up or display is not showing anything. I can switch to Vista and Vista boots works from grub menu. How can I test and configure graphics and monitor before installer boots the system?
View 1 Replies
View Related
Nov 7, 2010
my friend using XP and it was closed because he didnt activate it . he want to try Linux , i adviced him to use UBUNTU 10.10 ,but after we order the boot we got a loading screen for ubuntu then this error appeared
[code]...
also , the labtop cannot boot from usb coz no option for that in BIOS. what can i do to solve each problems?
View 2 Replies
View Related
Jun 11, 2011
Strange line of text appeared on open gedit page on first use after upgrade from 10.04 t0 10.10. I was reading something and copypasting the odd bit onto a gedit note: left the room, returned to find blank page except for "nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn". Then I saw that it was just the tail-end of a longer line which had stretched the page width to max, and by deleting backwards I arrived beneath my intact notes. The line was "I[my bolding]nnnnnnnnnn...nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnby v9898". I googled v9898. And there's a v9898. com. It provides something for Windows systems.
View 1 Replies
View Related
Nov 6, 2010
I have completed building gazebo, and everything was done successfully according to the following link [URL]... bot_Simulation , but when I tried to invoke gazebo using the command "gazebo /usr/local/share/gazebo/worlds/pioneer2dx.world" it returns the following error
[code]...
View 1 Replies
View Related
Dec 8, 2010
I'm totally new to this linux thing and I have a very strange problem. I downloaded the .iso and burned it to CD as per instructions. I had intended to install alongside existing WinXP Pro Sp3. Everything seemed to be going fine until it the installer got to the "User Info" Screen where it asks for my name, the computer's name, password, etc. At that point nothing I did would allow the "forward" button to work. I backed up a step or two and went forward again to no avail. I ended up hitting the hard reset button to get out of it. I never saw any error messages even though I scrolled through the install log at the bottom of the install window. Now my HDD is 60 Gb smaller (The part intended for Ubuntu) under Win XP and I have no idea what to do about it.
My system:
Asus P5NE-SLI Mobo
Intel Core2 Duo 8400 3.0 Ghz
2 Gb ram at 800Mhz
Nvidia 9800GT GPU 512Mb
Win XP seems to be working normally except for the loss of HDD space.
View 3 Replies
View Related
Aug 15, 2010
I have installed Debian maybe 30 times over the years since about 2003, stable, testing and Sid on two different desktops and two different laptops. The only problem I have ever had is sometimes with a flaky daily build. It is one of my favorite distros.
BUT, I am totally frustrated is trying to install to a USB. I have followed the manual step by step about 6 times in the past two weeks. The result is always the same. The installation fails to find an installation iso image. Yes, I know the iso image and the hd-media vmlinuz and initrd.gz files are supposed to be the same version.
File: debian-testing-i386-netinst.iso from: [url]
Files: vmlinuz and initrd.gz from: [url]
The USB boots to a Language selection screen and proceeds through the Keyboard selection screen with no problems.
The next step which searches for an installation iso image fails.
Skipping that step and trying to load installer components from iso image also fails.
Searching the entire PC for an installation iso image also fails. (I even copied the netinst iso image to the HD root directory.)
View 6 Replies
View Related
Sep 20, 2010
I'm having is trying to install ubuntu 10.04, when i get to the end and it asks you to click OK to reboot it never does, it sits there and never reboots (left for an hour!), forcing a shutdown and starting up then results in no GRUB coming up to dual boot (windows 7, installed on a seperate HDD)
This previously worked fine but I got rid of ubuntu to try a different flavour (which didn't install successfully, couldn't find the disk drive I wanted to install it on but I had already wiped ubuntu off for a fresh install)
I have formatted the partition i made (30gb partition) and manually created space for root and a partition from that for a swap file but this made no difference. I have used a partition manager and completely got rid of the partition (resizing the drive back up to full amount) and let the ubuntu installer do the partition itself but again the same problem.
I'm not sure what it is doing at this stage when going to reboot, i'm guessing installing GRUB and terminating the processes for the reboot, which never completes. I have also tried installing GRUB on the partition which said "Windows 7 loader" but that made no difference. I will try fixboot and fixmbr commands in windows recovery console in case it can't overwrite the boot sector for any particular reason tonight.
View 9 Replies
View Related
