Ubuntu Installation :: Screen And Mouse Don't Line Up After Fresh Install From CD
Aug 1, 2010
I just did an install of 10.04 from a CD. Now the mouse pointer has to be slightly above a button to click on the button. Also, the bottom bar of the screen is just a thin line and you can't see any of the controls on it and the top bar is too thick, with empty space about the menu items. It is like the whole screen is pushed down slightly.
There is nothing wrong with the monitor or the mouse because it all worked fine with 7.10 ubuntu, which was on the computer before I did the fresh install from the CD.
View 2 Replies
ADVERTISEMENT
Oct 16, 2010
I have put 10.04.1 386, 32bit, on a Toshiba C650 laptop. Took Win 7 off. Install seemed good. The only cd daily I could find was from August 16.I have a cdrom/dvd showing up but not much else. The mousesort of works, acts like it has an irq problem, jumps around and is slow. The touchpad works ok. USB sticks don't show up, nor ethernet card nor wireless card. An lspci shows everything there. Machine won't shutdown and is slow starting but does start
View 3 Replies
View Related
May 1, 2010
My laptop: MSI AMD Athlon 64x2 Nvidia GeForce GO 6100.
I've done a fresh install of Ubuntu 10.04 and I end-up with a blank screen. I've also tried a fresh install of Xubuntu 10.04 and Kubuntu 10.04 and I get the same blank screen.
Ubuntu 9.10 was working perfectly though. So what do you think happened?
I installed the Ubuntu 10.04 livecd on my desktop and it works perfectly so I think it is not a burning problem.
View 5 Replies
View Related
May 11, 2010
I downloaded and burned Ubuntu from ubuntu.com (64bit version) while in windows 7 64 i popped the install disc in, and it went into a setup in which it installed it asked to reboot, and I allowed. upon reboot boot I could choose either Windows or Ubuntu, so I picked ubuntu and off it went. It started to boot into the (Ubuntu) OS, it shows the little ubuntu thing, then the display goes black, like there is no signal to the monitor. The PC still runs, and reconizes when I plug in an iPhone or something, there is just a black screen though. I would like to know how to go about fixing this?
View 3 Replies
View Related
Aug 1, 2010
I just setup a Fujitsu s6231 lifebook with Lucid. When I boot there is no grub menu unless i press the "start" key. Then the only way i can get into the machine is by entering into recovery mode and booting in "safe graphics mode".
Everything works fine once I am able to log on the "safe graphic mode".
If i don't press the "start" key the ubuntu logo will flash for 3 seconds and then the screen goes blank and nothing happens.
View 3 Replies
View Related
Dec 8, 2009
Ok, I booted with the live cd and used Fdisk to delete all partitions and wipe the drive. I used the "Replace existing Linux system" install option and let it roll. So I reboot to the screen Flashing a _ then just black...System Info:GIGABYTE GA-EP45-UD3L LGA 775 Intel P45 ATX Intel Motherboard Intel Core 2 Quad Q6600 Kentsfield 2.4GHz 2 x 4MB L2 Cache LGA 775 Quad-Core Processor MSI R4850-T2D512 Radeon HD 4850 512MB 256-bit GDDR3 PCI Express 2.0 x16 HDCP Ready CrossFireX Support Video CardSeagate Barracuda 7200.10 ST3250410AS 250GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard DriveKingston HyperX 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 1066 (PC2 8500) Dual Channel Kit Desktop Memory Model KHX8500D2K2/2GRYes i did just copy my old newegg orders I'm brand new to fedora as well so I apologize if this a newb mistake.---------- Post added at 05:54 PM CST ---------- Previous post was at 03:41 PM CST ----------Update: I went and wiped the drive again and tried a different install method (use entire drive)After rebooting i spammed esc and got into grub and loaded fedora in nomodeset After going thro all the lisence and reg stuff it prompted me to log in, I did and once again im left with a black screen with a _
View 11 Replies
View Related
Jan 9, 2010
So I currently have an install of Karmic running that has been upgraded over the years but I am repartitioning my drives so I did a fresh install on a new drive.
My first problem was the live cd would not boot and I had to use the alternate cd to do the install. It would boot into a blank screen and the i915.modeset=0 kernel parameter did not help.
After the installation finished I went to try and boot and found that right when it went to initialize the graphics, my computer locked up hard. Keyboard unresponsive and all. I read the forums and I tried using the kernel parameter i915.modeset=0 and removed quiet and splash from the kernel line to see if I could spot any errors but nothing appeared.
I am able to boot into recovery mode, and I tried even running an apt-get upgrade to get all my packages up to date and installed the latest nvidia driver but still have this issue.
I'm at a loss as to what I should attempt next.
Here is boot info, just to clarify sda and sdb are a fakeraid on my old setup, sdc is my new install
Boot Info Summary:
View 1 Replies
View Related
Mar 12, 2010
I was able to boot up the live CD and install the OS to the hard disk. *Single boot.After I rebooted, the system loads up to the Ubuntu splash screen and will "eventually" move along. The problem is that once it moves past the splash screen, it starts blacking out the screen. It looks like the screen turns on for about 10 seconds and then off for another 10 seconds repeatedly. The screen blinks like this indefinitely.This is my first attempt at installing and or using Linux so I am an uber n00b.
** Also, I am able to ctrl + alt + f1 and get to the terminal so i should be able to run any commands without any trouble.
View 1 Replies
View Related
Jul 8, 2010
I boot up after a fresh install and I don't get a boot splash screen. I really cant find a way to fix and some times it does not go to the login screen.
View 1 Replies
View Related
Nov 28, 2010
I installed Xubuntu (Karmic 9.10) several times on an old iMac G3 with powerpc processor. Previously I had installed versions as 6.06 and 6.10 succesfully. But no luck this time. All installs were succesfull if alternate cd's were used.
The problem is that when i boot up i see the bootloader 'yaboot' and after that shortly the mouse logo from Xubuntu. After that the screen turns black and the indication light from the powerbutton turns from green to orange, this means no signal (i guess).
I assume that my screen resolution is wrong and cannot be displayed, the Mac uses 1024x768 if i am right.
My question is : How to access any configuration file to change resolution as I believe is the problem?
Edit: Perhaps there is a way to access command line to change config files.. ? Or using a live CD, but this computer is low on memory and has a hard time using live-CD's.
View 1 Replies
View Related
Dec 31, 2010
I've installed a fresh Debian amd64 DVD version on my small HP Compaq 6537s / AMD Athlon X2 / 64. Everything went fine, I rebooted, the graphical login screen appeared, so I thought I will be able at last to run Debian on a computer ...
But then after login, the login Window disappeared, the "Debian" logo too, and... that's all folks! A nice blank screen. But the mouse is still perfectly drawn, so it's kind of weird.
Here's what tells me "uname -a" :
Linux olivierdebian 2.6.26-2-amd64 #1 SMP Sun Nov 21 09:17:22 UTC 2010 x86_64 GNU/Linux
If I go to CTRL-ALT-F1, i login as root and I do a "/etc/init.d/gdm restart", I have the login screen back and this is once again the same scenario: login => ok => blank screen with mouse properly drawn and the Debian background color still there.
View 2 Replies
View Related
Feb 24, 2011
I've now tried several times to install a fresh copy Fedora 13 i386 on my old Dell laptop, but each time I reboot the laptop I get the first-time welcome screen which asks you to create a user. When I re-enter my user info, it tells me that there's already a folder created for that user. After rebooting, I'm back to that screen. Does anyone know what's going on here?
View 2 Replies
View Related
Aug 9, 2011
After installing Fedora 15 from LiveUSB and rebooting it just hangs on a black screen with a blinking cursor (underscore) in the top left of the screen. If it's reached grub, it isn't responding to any commands, and mashing several key combinations (such as ctrl-alt-f1) will produce a beep usually emitted only by the BIOS (hinting that it may never be making its way to grub).
The only particularly interesting thing about the install is that by default it wanted to boot itself from the MBR on my primary-master (Windows) disk. Instead I selected the option to boot from "the first partition in sdb1", which is my primary-slave (Linux) disk, (the first partition being /boot). This way I can change which OS boots by changing the boot order in my BIOS, and so avoiding bootloader wars.
View 5 Replies
View Related
Jul 29, 2010
Ubuntu 10.04 64 bit, GNOME desktop. Previous install (same OS) gave an error when switching users. Did a fresh install, and now the keyboard and mouse freeze. This happens almost every session. I have to force shutdown. Sometimes it happens in 5 minutes, other times it happens in 4 hours. I don't want to sound like a jerk, but the Ubuntu problems are starting to get to me. I really want to use this. I like it, but I'm getting frustrated. 9.10 had wireless problems, and now I'm getting this freezing thing. Both the keyboard and mouse are USB connections. Everything else works when the freeze occurs, i.e., video's still play, web browser is still displaying gifs, etc. Only the mouse and keyboard freeze. All other operations seem normal.
View 3 Replies
View Related
Jun 17, 2009
I have install fedora11 live and the mouse work well when installing.When you reboot the mouse works ok until the welcome screen apears then the mouse stops working and I cannot continue with the postinstall. I have a 1TB usb externalHD that I am installing fedora11 and have partitioned it so that I have 500Gb free for fedora, system is doucore 2.4,4gb RAm, I tryed doing this with three differend mice and connectting the mouse to different usb ports
View 4 Replies
View Related
May 22, 2011
I did a fresh install of Ubuntu Studio 11.04 on a machine with Vista previously installed. The computer also came with a Personal Media Drive (movable harddisk) of 500GB. The only modification to the HW conf is that I recently added a harddisk of 2 TB that I wanted to install Ubuntu on. (I.e. in total 4 harddisks on the scsi slots)I ran the install cd that I burnt form the iso and I chose the option to manually partition the disks, and I only partitioned the new Harddisk. The installer chose to make some partitions: grub as the boot loader, one ext4 partition of 2 TB and 3.5 GB swap space (and some kb of waste space).
The install cd was readable and the tests that could be performed on the install cd itself and on memory terminated ok, and install seemed to have worked fine. It also discovered the Vista / ntfs partitions. I thought the install would work ok since I had made the new disk the 1st to boot in the HDD boot priority in BIOS setup.
When I rebooted after install I got a blank screen. I then tried with making the Vista HDD the 1st to boot in BIOS, and then I got the GRUB screen with two options for ubuntu two for mem tests and two for the Vista partitions.I found it strange that GRUB would take over, since the grub partition should be on the new lower prioritized HDD in the boot order.When I run the first Vista option everything works. Vista boots. However, when trying to get it to boot either of the ubuntu options I get a flickering screen, in the normal ubuntu boot a white one where the upper third of the screen is more steadily lit up whereas the lower 2/3 is flickering. When booting with failsafe option the color is red/pink instead, but with the same flickering.
View 5 Replies
View Related
Jun 30, 2011
I ordered a SuSE 11.4 installation DVD from an online Linux Distro distributer that I've used before with no problems. I did this rather than burn my own DVD from the website. I thought that I might perform a fresh install of SuSE 11.4 on this Dell 1420 Laptop that is currently running Ubuntu 11.04.
Note, this is a completely fresh install, not a side-by-side installation with Ubuntu; I followed the installation sequence that completely repartitions the entire disk for SuSE, and accepted all of the suggested options regarding logon, etc.
Everything goes well ... sort of. The first install didn't reboot correctly, i.e., the set-up that is supposed to run after the initial install never happened and I had to manually power-down the machine and restart from the "safe mode." Needless to say, that didn't work as expected. So, I re-install, from scratch, trying different options: for instance, instead of LVM, I decide to have an un-encrypted partition scheme and accept the "obvious" options ... thinking that the LVM options interacted badly with the install. Eventually I get the installation to proceed correctly, or so it appears: it goes though the entire sequence, including the re-boot, building the default image, etc.
I test this image by removing the DVD, power-cycling the machine, and all looks good, so I begin the process of installing software updates, etc. Being paranoid, I re-boot the machine, and all restarts correctly, etc.
Now here's the annoying thing. The next day, I power the machine on, and it locks at the splash screen. By the way, these are the exact symptoms that I experienced with the bogus/incomplete installations. The boot sequence proceeds up to the splash screen and waits forever.
So, in sum: I spent inordinate amounts of time attempting to install this software, carefully following the instructions provided by the installer. In every instance, after leaving the machine off for a day or so and rebooting, I am met with a splash screen that sits forever. Needless to say, I am extremely reluctant to repeat another day of software installation to only have to re-start with no assurances of success. Either I go back to ugly Ubuntu (which has always worked out of the box, by the way), or I look at other options. I was hoping to use SuSE, but I really don't care which distro is on that machine as long as it works and it provides TeX, R, Emacs, Scheme, and a few other software packages that I'm sure are of no interest to your customer base.
View 4 Replies
View Related
May 1, 2010
After the upgrade from 9.10 to 10.04 resulted in a black screen after reboot, I decided to don't waste more time, backed up my data and made a fresh installation.
First Issue [solved]: After I inserted the Kubuntu 10.04 Live-CD and started the system, I got to the CD's boot-mode selection menu. When I selected "Install Kubuntu", I got the Kubuntu bootscreen, but the system hang up then. I was able to solve this problem through pressing F6 in the boot-mode selection menu and setting "nomodeset". I also had to remove "quit splash" from the boot-entry line. Afterwards the installation process was fine.
Second Issue: I wanted to boot my new installated system, but, off course, got the blank screen again. So I edited the Grub-entry for recovery mode in the grubmenu (replaced "quit splash" with "nomodeset") and booted into recovery mode. I selected "netroot", and installed the proprietary nvidia-drivers with "apt-get install nvidia-current". Afterwards I ran "nvidia-xconfig" to generate the xorg.conf. To solve the blank screen issue, I edited the /boot/grub/grub.cfg the same way I described above and rebooted. Now I don't get a blank screen anymore, but I also don't get an XServer. The system boots now (off course without splash and "unquit"), but drops me into the tty1... When I type "sudo service kdm start", I get into KDM and can login, but I get many errors and crash-reports there. I also don't have any internet. I only have internet when booting in recovery mode and select "netroot".
I'm a bit surprised that Ubuntu released a LTS-Version that causes so much trouble (I've searched the forum and it seems that I'm not the only one with such big problems). Has Ubuntu droped support for NVidia-users?
View 9 Replies
View Related
Jan 26, 2011
I am running a dell poweredge 2600 in which i just now did a fresh install of Centos 5.5 KDE. The install went perfectly with no hiccups or errors. I reboot the server and centos dose its normal checking everything and giving a Green"OK" or Red"Error" and everything seems to be fine. I then get to a black screen with a X mouse cursor, i can move the cursor freely and i can turn the Num Lock key on and off and i can do a Ctrl+Alt+F5 and then reboot with a Ctrl+Alt+Del smoothly, but i just cant get the centos to boot up all the way into the GUI.
View 3 Replies
View Related
Nov 24, 2009
I installed F12 with the i686 KDE livecd. A black screen with a blink "-" appeared after the bios information on the first reboot. The computer does not respond to any key input except "ctrl+alt+del", which restarts the computer.The machine is a dell inspiron 6000 with inboard 915gm video card, and the bootloader was written to the harddrive mbr. Any help would be highly appreciated.I need to be more clear. Installation went fine, problem appeared on the first reboot.
View 9 Replies
View Related
Dec 19, 2010
I'm trying to install Ubuntu 10.10 from a Live CD. I can get to the Menu where I get to choose "Try without installing","Install Ubuntu","Test Disk," etc.After hitting ANY of the options, it hangs on a black screen, sometimes with a cursor blinking in the upper left, sometimes not. From all the research I've been able to dig up it seems it's a graphics card issue, but I haven't been able to find anything exactly like my problem as most everything I've been able to find say's theirs continues to install but then causes problems later, or they're trying to load on a dual boot system. I can't seem to get past that first "Install Ubuntu" selection. As soon as I hit enter it goes black.
I'm wondering if I can't load the nvidia drivers from a command line before I attempt to install from the live CD, but I don't know how to do that. I have the .run file downloaded but don't know where to go from there.
View 9 Replies
View Related
Jan 26, 2011
I am running a dell poweredge 2600 in which i just now did a fresh install of Centos 5.5 KDE. The install went perfectly with no hiccups or errors. I reboot the server and centos dose its normal checking everything and giving a Green"OK" or Red"Error" and everything seems to be fine. I then get to a black screen with a X mouse cursor, i can move the cursor freely and i can turn the Num Lock key on and off and i can do a Ctrl+Alt+F5 and then reboot with a Ctrl+Alt+Del smoothly, but i just cant get the centos to boot up all the way into the GUI.
View 16 Replies
View Related
Apr 22, 2011
I tried to update one of my home machines with a fresh install. This is far from new to me so I did not expect any problem. But I was proven wrong. First: did install the system as usual. First anomaly: system blocked during the install process but did restart it flawlessly one I tried to eject the DVD from the player. It needed actually that intervention to retake working. It then went to install and froze during the first system start. I rebooted with failsafe settings, it then correctly configured. I reached a beautiful desktop. I performed the updates from the update repository and I joined the nvidia proprietary driver repository (which updated to the G02 driver).
I then rebooted the machine and now I am in trouble. In normal mode the system (dual boot Opensuse, XP) does not boot at all and freezes immediately after hitting enter as before. In safe mode it goes further but does not reach X anymore. It blocks with the following line statement: "system console stolen at line 266". I then tried "startx". But the system goes into a scrolling loop that does not allow me to read the output. how to get at least the error message of the loop? I read some line passing by that the system might have an X11 authorization problem.
Athlon Phenom X4 905e
Nividea G7600 graphic card
Former system installed and running flawlessly: 11.1
View 9 Replies
View Related
May 19, 2010
I have a computer with redhat installed that once it boots up it comes to an application login screen. I want to bypass that and get root access to reformat hard drive and install latest version of Debian Linux.
View 1 Replies
View Related
Mar 28, 2011
I installed CentOS 5.5 last night using the DVD ISO (from a USB drive thanks to the Universal USB Installer). I selected the Server and Virtualization packages, and finished the install all the way through. At the end, the installer asked me to remove any installation media and reboot the system. After rebooting, the system hangs on a blank screen with a blinking cursor in the top left corner that does not accept text. This is before the GRUB screen appears. For partitioning, I created a 4GB swap partition on sdb and a 16GB ext3 partition on sda, mounted at /, with the remaining free space on sdb mounted at /storage.
Does anyone know why this system is hanging before the GRUB menu?
View 4 Replies
View Related
May 29, 2010
I upgraded to 10.04, upgrade went fine but now I have lots of problems.My wireless internet is extremely slow, its as if I am on dail up.My Rogers Rocket stick that used to work perfectly is now not connecting to the internet wich is a huge problem for me.Flash player now dont work either and Mozilla thinks its not even installed.I cant change the time and date, it tells me I have to unlock to change the Time but when I click on unlock nothing happens.Who knows what else is not working either.
I am not impressed at all with 10.04, my laptop and Netbook used to work perfectly before the upgrade and now I have tons of problems.What can I do to fix my problems or will a fresh install work better
View 7 Replies
View Related
Oct 5, 2010
I have a >5 year old laptop, running Maverick (Ubuntu 10.10) but I need to do a clean install since the video driver is all screwed. The laptop is without USB boot option in BIOS. The CD drive is physically removed.
The HD partitions are
/dev/sda1 (ext4) 15gb mounted as /
/dev/sda2 (extended)
/dev/sda5 (linux-swap) 2gb
/deb/sda6 (ext4) 20gb mounted as /home
How can I do a fresh install??
View 1 Replies
View Related
May 26, 2010
I have just made a fresh install of Ubuntu 10.04 on my laptop which was already running on windows 7. The installation itself was ok, however, after the restart in the end it did not want to load anything. I get just a blank screen. I am not much of a linux expert, so all I could do is start thee computer via a live cd and see what is there. And it looks normal - windows is intact, new linux partitions are there, GRUB is also there. What should I do? Reinstalling everything is not a proper solution...
View 9 Replies
View Related
Jun 8, 2010
I have a new 500GB disk, with a partition with Windows XP, one with Windows 7, one for Ubuntu 10.04, one for /Home and one for swap. The systems were installed in that order. But after finishing with the Ubuntu installation, removing the CD from the drive and restarting, GRUB never showed up, and the system went straight to the Windows OS selector; the one prompting to start Windows 7 or an "Earlier version of Windows". So I can't get to Ubuntu, even though it seems it installed just fine.
As a note: just after the installation process ends and it shows the "remove CD" message, it spilled out a list of I/O errors in some sr0 device or something. But I just installed the same Ubuntu on a friend's computer and it showed a similar error list, yet his system works just fine... However, he doesn't have Windows 7, thus no OS selection screen other than GRUB. I didn't want to rush into editing the MBR or re-installing GRUB before I knew I had to do that.
View 9 Replies
View Related
Oct 2, 2010
I want to use my old home partition as home whereas currently there is a 35gb partition that was my old home and a new 'home' within /. how to make my old home recognised by my new install of Lucid.
View 1 Replies
View Related
