Ubuntu Installation :: Blank Screen After Grub Selection On 11.04?
May 15, 2011
I downloaded Ubuntu 11.04 yesterday. The ISO allowed me to install Ubuntu using Wubi and it worked just fine in Windows (I used a virtual drive to mount the ISO). I liked it enough to want to replace Linux Mint on the Laptop with it.After a LOT of trying, I was finally able to make the liveUSB of Ubuntu 11.04 32-bit version.[URL]isplays the boot menu and if I select 'try Ubuntu without installing', I am greeted with a blank screen which just does not go away until I hard reboot the system. Also, the grub I am getting is NOT the purple one which usually is the default; instead, its a dark screen with a black-n-white titled Ubuntu logo. So the question of using the NOMODESET doesn't arise at all. I am using Dell XPS 15 with dual OSes - Linux Mint and Windows 7. Both Mint and 7 are 64-bit OSes but I am trying to install Ubuntu 11.04 32-bit version.
View 8 Replies
ADVERTISEMENT
May 3, 2010
First let me describe my system setup. I have windows, ubuntu 64 and ubuntu 32 present. I upgraded the 32 bit version to 10.4 with no problem. After upgrading the 64 bit version is when the problem occurred. I believe it has to do with the grub.cfg file. When I would choose the 64 bit version the screen would just go black, no furthur action. After making a few changes to the 64 bit selection in grub.cfg i come to a screen that says c to continue, s to skip mounting, and m for manual mount. Pressing s gets me in. Here is a copy of my grub.cfg.
#
# DO NOT EDIT THIS FILE
#
# It is automatically generated by /usr/sbin/grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
#
[Code].....
View 1 Replies
View Related
Feb 17, 2011
Im using the following system setup: When I boot my business computer, I can choose between 3 setups, 2 Windows XP, 1 DOS. I installed Ubuntu with 1 Windows XP system which looks something like this:
System 1 (XP)
System 2 (XP) --> after selection, Im able to choose between the XP system and Ubuntu on a new screen
System 3 (DOS)
Now interesting for me is obviously System 2. After I select System 2, I can choose between XP and Ubuntu. After I select Ubuntu, I come to another screen, where I can choose again between 4 Ubuntu entries with different kernel versions (including their recovery modes) AND both XP systems (yes, again). I installed Grub Customizer. I removed all the XP entries and all but 1 Ubuntu entry from this screen. I also set the timeout until booting Ubuntu on this screen to 1 second to start as quick as possible and Ubuntu boots fine.
My question now is, is there a way to skip the screen with former kernel and XP selection and boot Ubuntu directly after already choosing (between XP and Ubuntu) on the first screen? I know, 1 second "waiting" is not too bad but skipping the screen completly would be superb.
View 3 Replies
View Related
May 20, 2011
I have installed Debian a few times now (and other distro's), so I'm fairly used to installing linux. I'm not used to installing it on Apple hardware (back in 2009 on my laptop I had some issues that were solved rather quickly, but that's about it). Now I'm installing Debian Squeeze on a new (well, bought today, but it is the previous model: iMac 11,2) desktop iMac.
Installing goes well (resizing partition, rEFIt, booting Debian 6.0.1a netinstall CD, installing packages etc.) I followed a tutorial [URL] to install grub explicitly with force after installing and running gptsync. Everything went according to the tutorial and I rebooted to be welcomed by rEFIt and then grub: perfect!
BUT when I chose Debian in the grub-selection list, I only see a few lines of starting the kernel, and then my screen goes all black. A few seconds later I hear a sound, and iirc it's the sound of gdm prompting to select a user. I cannot switch to a TTY and I have to use the power-button to shut the system down.
View 6 Replies
View Related
Aug 5, 2010
I have an HP computer nvidia and AMD stickers on it and 1GB RAM. HDD is Parallel ATA. I downloaded both Ubuntu & Kubuntu Live CD. Both live CD's boot to a blank screen. After a (seemingly) successful install of kubuntu, the screen goes blank after GRUB.
Here are the details: With this HP, when i boot from ubuntu live CD the screen goes blank. It does not give any option about trying ubuntu, install, ubuntu, mem test. I just get a blank screen. On my ASUS laptop the ubuntu live CD goes straight into ubuntu live (without having to choose an option). It is not the CD When I boot from kubuntu live cd i get to the screen where i have an option to try kubuntu, install kubunt, memtest..
If I choose either try or install, my screen just goes blank & never progresses. Again, this live CD works on my ASUS laptop. At the bottom of the boot screen for the kubuntu live CD i noticed f1-f6 configurations. I was unable to change any other than language and f6 options. If I press f6 i get options which i can mark with an x. I don't know what any of these mean but I checked all of them and then on the boot menu popped up
BOOT **a whole bunch of text** I went onto install kubuntu and it no longer went to a blank screen. Rather it was a fuzzy grainy splash with the word KUBUNTU and loading dots underneath. Atlas it seemed to prevail, the installation process started (fuzziness went away). The installation screen now looks just as it did on my ASUS laptop. I continued through the steps with an installing on the entire HDD. The installation completed (with no signs of error). Screen said take out disc press enter.
I did so and my computer turned off. I power up the computer and the GRUB loads up. I have option of regular and fail safe. Both lead up to a blank screen. My monitor seems to think there is no signal and goes into standby mode. Perhaps the video card is not rendering correctly or not compatible.
View 2 Replies
View Related
May 31, 2011
I am installing 11.04 on a Gigabyte E7AUM-DS2H with an onboard GeForce9400. I'm trying to turn this into an XBMC htpc. I'm not using xwindows or anything like that. Going straight to console for now. I'm experiencing the GRUB Black/Blank screen. I just don't know what else to try...
1. I've changed the kernel boot options, i.e. nomodeset
2. I've toggled the GRUB_GFXMODE=640x680 line
3. I've remembered GRUB-UPDATE
4. I can get into GRUB menu using SHIFT at bootup, messing around with settings and CLI there
5. I started with default nvidia drivers (not good), and then installed nvidia-current - that works better.
6. At the blank screen, I can hit ALT-F1 into console/tty fine.
7. If I use nosplash --verbose, I get a long wait with a blank screen, then the last bits of the bootup log and the login prompt.
8. And stuff I've forgot I've done....
Now what I really can't understand is that I have XBMC installed AND working beautifully. I can set XBMC to autorun with no trouble at all. It's just the period between bios and XBMC that it all goes dark. When I quit XBMC, I get a blinking cursor, which I can F1 to the console. What is it with GRUB??? What am I missing? Why is this so difficult? I COULD live with it, but its just not right, and I want to get it right.
View 6 Replies
View Related
Jun 3, 2011
I recently wanted to install ubuntu 11.04 on my computer (which had vista on it and I wanted to just completely wipe that out). After the install I noticed that my monitor would not receive signal during boot (I heard the little drum noise but my monitor said no signal). So I tried following these instructions (which have worked in the past): [URL]
but when I boot the computer I don't have a GRUB menu! It just automaically starts booting ubuntu 11.04. Is this because that is the only OS I have installed? Did I do something wrong? What can I do to fix the problem?
View 2 Replies
View Related
Nov 30, 2010
I've tried to find it on google, but I want to have my OS Screen Selection to have a cleaner look than what it currently looks like. I understand we can edit Grub 2 but nothing I've found shows me what to edit into the file. I have all of the files I just need to know which one to edit and what to put into the file so my OS selection looks better
View 2 Replies
View Related
Mar 12, 2010
I've just installed ubuntu 9.10 from a live cd on to a 2nd HDD, with vista on the 1st. When I turn my PC on GRUB comes up and I can select ubuntu or vista, vista works but when I try to boot ubuntu the screen goes black with a small flashing underscore in the top left and then just goes completely black, nothing else happens after this. I've tried reinstalling from the live cd but when I go install nothing happens and the screen goes black again. When I was installing I changed the boot to something like scsi?
My PC's specs are:
Dell inspiron 531
HDD1: Ubuntu(300GB)
HDD2: Vista(1TB)
OS
Windows vista
Graphics card.
ATI radeon HD 4700 series
CPU
AMD Athleon 64 x2 6000+
Mainboard
Manufacturer : Dell
Model: 0RY206
BIOS: dell 1.0.13
View 3 Replies
View Related
Mar 19, 2011
I am trying to install Ubuntu Server 10.10 on a computer with 5x 1.5 TB HDDs. I went through the process of partitioning the five hard drives into three partitions each:
sd*0 is a 300MB partition for /boot, RAID1, 2 active, 3 spare
sd*1 is a 500MB partition for swap, RAID1, 2 active, 3 spare
sd*2 is a 1.5TB partition for /, RAID5+LVM, 5 active, 0 spare.
md0 is the raid1 on sd*0
md1 is the raid1 on sd*1
md2 is the raid2 on sd*2
During the install, everything seemed to work fine with the formatter, but the installation ended in error. I booted into rescue mode and found that though all the drives were U (in /proc/mdstat), it was resyncing. I let this run (overnight) and the next day, jumped back in and installed the OS successfully.
However, after installing GRUB, when the installation process asked me to reboot, the system came back up with a blank screen (blank, save for a blinking cursor) and didn't move from there. I am thinking that the problem is GRUB, since I can boot into the main LVM partition via the rescue option on the install cd. Here's what bugs me:
[Code]....
View 9 Replies
View Related
Jan 25, 2010
I installed fedora 12 to a 4GB flash usb flash drive. When I reboot and select windowsxp, grub displays a blank screen and hangs up.
[root@localhost Terry]# fdisk -l
Disk /dev/sda: 160.0 GB, 160000000000 bytes
255 heads, 63 sectors/track, 19452 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x41ab2316
Device Boot Start End Blocks Id System
[Code]....
View 2 Replies
View Related
May 1, 2010
I have just updated to 10.04 on my Dell Insperon 8200 laptop, and all seems well with Linux.My problem is that although it shows in Grub Windows XP will not load. I just get a blank screen with a flashing cursor.I have tried to grub-mkconfig and grub-update, both of which reported successful results.However on reboot I still get a blank screen for windows.This was not an issue with 9.04 and 9.10.so I don't think it is the machine.
View 5 Replies
View Related
Jun 13, 2009
[code]...
when trying to choose the Linux partition, I found that it would just hang at a blank screen. Looking further into the problem, I had booted with the Linux Rescue and checked the /boot/grub/grub.conf file. It appeared to be that the menu was set to hidden. I got rid of that line, and checked the boot arguments. It still had acpi=off set with the kernel and everything else seems to be in order. Root is set to root (hd0,2) which should be correct.
View 6 Replies
View Related
May 9, 2010
I am having the same problem, as soon as X tries to load my screen just goes blank. I have an ATI Radeon 9550. At first I tried switching between VGA and DVI as well but upon ruling that out, I switch to my on-board video card and that is working thus far, but I'm trying very hard to figure out a way to be able to switch back. Anyways I'll check back in later on if I have any new information I will post.
View 3 Replies
View Related
Jan 26, 2011
The day started as usual until I got the very bright idea to install Ubuntu. A new OS along side W7, that sounded great. I checked some guides on the Internet, it was all very straight forward. Install it and Grub will show you the OS:es when you boot up. I installed Ubuntu, rebooted. After the BIOS messages the screen goes blank and my screen on-button begins to blink, as if trying to find a signal, I press enter, it reboots instantly. After BIOS messages I get to a screen that says "GRUB error: uknown filesystem grub rescue>"
I've looked through everything here and nothing works. I've tried to fix the mbr-thingy using Windows Repair and even though it says "one partition was updated with new boot-thingy" when I reboot, I get into that very same grub rescue. I think my setup has something to do with it. I run RAID0 (2x360Gb hard drives), first having C: at 50Gb and then the rest as F: for programs and such. What I did was that I shrunk the F: part and then used that as partition for Ubuntu. Also please have a look at these screenshots, my partitiontables and such seems completely wacky to the raid: Where should the boot-loader go? I'm very, very new at this. I've had Ubuntu Netbook remix on my netbook for a time but still treat me as an utter beginner.
View 4 Replies
View Related
Oct 5, 2010
Installing 10.10 RC dual boot with Win7. Is there no place in the installer to specify where Grub will be installed? I don't want it installed in the MBR I want it in the partition with / (I usually only create two partitions for Linux / and swap). I prefer to chain load grub from my windows bootloader.
View 4 Replies
View Related
Jan 14, 2010
Finally got a dual boot on this laptop the way I liked it (LOVE my Win7, really like UBUNTU for certain things like getting booted and on the net fast...great). As I was editing and rebooting the GRUB settings UBUNTU got it's updates and installed (including one on GRUB that I hadn't seen before - WITH WARNINGS). Now I can't seem to get this last entry out of the boot menu: vmlinuz-2.6.31-14-generic. It has all this listed now (had dual entries for everything like mem test before):
vmlinuz-2.6.31-17-generic
vmlinuz-2.6.31-14-generic
Windows 7
I got rid of the extra entries like memtest and all using: sudo chmod -x /etc/grub.d/20_memtest86+ and such variations..still though I got one stuck in the boot selections. It won't remove the old linux vmlinuz-2.6.31-14-generic build entry from GRUB (and they both point to the same place). It has a -14 and -17 entry in it now. Like I said both load to the same mount point.
I mean I removed like five extra entries from GRUB using that command after the update (and had done it before about two months ago) but the linux vmlinuz-2.6.31-14-generic selection won't leave the GRUB selections now. I really thought I had it figured out to the bomb having my laptop dual booting before, just didn't like how UBUNTU used my disk space by default last time so I decided to rebuild the laptop.
View 8 Replies
View Related
Jan 2, 2010
I just attempted to install ubuntu for the 4th and 5th time and have yet again had a fail. This time it actually completed the installation, which is a first. however upon reboot it takes me directly to Vista - I don't see grub or a o/s selection choice.
View 9 Replies
View Related
May 10, 2010
I have installed these OS's in this order:
1 - Vista
2 - Ubuntu Server 9.04
3 - Ubuntu Desk 10.04
4 - BT4
I recently upgraded my most often used OS (#3) to 10.04 version and it updated GRUB to GRUB2 as part of the dist-upgrade. I have a feeling that I wasn't careful enough when installing BT4 or I made a mistake in the partitioning. I had plenty of space that was free waiting to be used by some other os and I designated some of that space for BT4.
When I got it all installed (off of a USB live boot) I rebooted and noticed it was back to grub one. The Vista install and the Ubuntu Server install both work still... but the recently updated (to Grub2) Ubuntu Desk install now hangs immediately after selecting it and pressing enter in Grub. I can mount the partition within BT4 just fine and see that all my data is still there, it just won't boot.
What I've tried Using BT4 to install Grub2. (no luck) Installing Grub1.5 back after finding Grub2 didn't work. (no luck) My plan When I get home from work today I'm going to take the "quiet" option off of the boot command in Grub for that Ubuntu OS and see if there's any error it's dumping before it hangs.
Hope that someone has had this issue before and can just tell me a straight forward way of resolving this issue. I'd prefer to use GRUB2 as my boot loader.
Cliff Notes Had other OS's installed Updated to newest Ubuntu (installed GRUB2 as the new bootloader)Used some spare disk to install BT4 New Ubuntu that used Grub2 is now the only OS that won't boot
View 5 Replies
View Related
Feb 20, 2010
Anyway one day I start my computer and instead of starting normally it comes up with a screen which says GNU GRUB version 1.97~beta at the top. I selected the option Ubuntu, Linux 2.6.31-19-generic as I figured this is what normally loads without being prompted in the grub menu, but after this I got the ubuntu logo for a few seconds then my screen goes blank. My laptop is a hp510.
View 9 Replies
View Related
Jan 4, 2010
I downloaded the Ubuntu ISO file and burned it to a CD-ROM. Booting from the CD on my laptop I select the language and selection screen appears with all the F1-F6 options below. I've tried all the selections and options through the F keys but that's as far as the install will go. My laptop is a Dell and it's only 3 years old with plenty of memory and HD space.
View 3 Replies
View Related
May 29, 2010
I've been using Ubuntu on and off ever since about 8.04. This newest release (10.04)... wow it's amazing. That's all I can say. The only gripe I have right now is that right after I select Ubuntu from GRUB, the screen goes black for about 10 seconds, then goes to the bootscreen. By the time it gets to the bootscreen, the bootscreen is shown for about 3 seconds, and then I get the lockscreen. I have a nVidia card with proprietary graphics drivers installed.
View 1 Replies
View Related
Jun 24, 2011
And by blank screen I mean after I pick whatever I want on GRUB. There's NOTHING.I even tried going in recovery mode. But same thing.Right now I'm using an older recovery. The newest thing is completely broken. And the regular one for the Ubuntu version doesn't work either.
View 3 Replies
View Related
Sep 1, 2011
So after installing linux for the first time - version 11.04, first there are 1000 problems which don't fix especially the fact it didn't boot into linux half the time. I managed to get on it and there was an update, thinking this would fix something I updated it and now I can't do anything on my laptop! Before I could atleast log onto windows but I can't even do that now. The place where you can press f12 to go into the bios and change priority I can't even get there because when it says to press f12 I press it but nothing happens and it still takes me to a blank screen with no grub menu no nothing.
View 9 Replies
View Related
Feb 5, 2011
I just installed ubuntu 10.10 did a clean install, formatting the previous ones. Install completed successfully, rebooted, entered in GRUB, chose linux, linux starts the my screen goes black, there is no signal coming to my monitor, linux runs fine though i think because I hear the ubuntu login drum. I press ctrl+alt+F1, but can't get to console either, the screen is looking for input signal. Should note the I have a Palit NVdia 9600GT gpu because I saw that people with NVdia card sometimes have similar problems.
View 2 Replies
View Related
Apr 20, 2011
tried to edit boot time from 10 secs, used correct commands in terminal, then the menu.lst appears but the screen is blank there is no text to edit
View 5 Replies
View Related
Apr 25, 2011
i have 2 hard drives connected to sata ports randomly on my motherboard ( i didnt do it in any order )
1. Western digital 500GB - Windows 7
2. Seagate 500GB - Linux HDD - had ubuntu 10.04 on it before suse
Ok basically, ive been trying distro's by installing them on my linux HD, my favourite is ubuntu, but i wanted to see what else is out there so i tried out OpenSUSE, and with suse i unfortantly came across many problems with grub-legacy, and i solved that eventually by changing my boot hard disk in BIOS to the seagate, and installing grub on that Ive never had a grub issue in the past using ubuntu, only with suse Then i decided to go back to ubuntu because everything just works and i like .deb packages, so i installed 10.10 32Bit
Everything went fine, chose default install options, formatted the Seagate drive, and installed to the seagate, HD changedt the boot drive to the western digital in BIOS ( were ubuntu likes to install grub in the past ) booted fine, installed fine, grub showed fine, booted to linux then i went back to windows for a day of gaming and fun, i just rebooted about 30 minutes ago to play with linux, and i cant access the grub menu my pc goes to the POST screen and then were grub should show, i get a blank screen and the pc just reboots to the POST constantly this problem has never happened with ubuntu, ive had 10.10 before, this is all started after removing opensuse
ive tried F8 and booting from both drives, the seagate i just get a white underline for ages and nothing happens and i cant boot to windows on the WD Im currently on my livecd im using the 11.04 livecd, all my cds arent labelled, so i have no idea which is which, i just chucked one in to get a browser, but i gotta say natty 11.04 IS AWSOME
View 9 Replies
View Related
Aug 1, 2010
I installed 11.3 as a new install over 10.3, kept the $home and windows partitions, and let it reformat the other two partitions. NO disk partitioning structure was changed.
I did get a warning that GRUB over 128GB might not be able to boot.
I did enable the MBR.
GRUB menu does come up, but upon selection of SUSE 11.3 entry the computer screen blanks, and nothing happens. Selecting Windows does work upon power-up.
I did not have this 128GB issue with 10.3. What are my options? I am really afraid to install 11.3 on production machines now (running 11.2).
View 3 Replies
View Related
Dec 26, 2010
Is there a known problem with the Lubuntu 10.10 image here? I have downloaded it to two different computers, then burned the images to two different blank CD's (different brands) and neither loads. Both only get as far as the Lubuntu menu, once ENTER is pressed at that point to load the LiveCD, a blank screen eventually appears with a flashing cursor at the upper left of the screen, that's it. They were both burned using the slowest burn speeds available.
View 9 Replies
View Related
Jun 8, 2010
First time I am having issues with Centos.
I bought a Intel DQ45CB LGA Q45 Micro ATX Motherboard and I am installing the 64 bit version of centos.
The install of Centos goes just fine. However when I first try to boot up, after post is done, I get a blank screen. I do not even get on the Grub screen. No access to any of the ttys. No access to anything, files, folders. I only get a blkinking cursor, no command prompt, nothing.
This happened with Centos 5.2 and 5.3
Just for the hell of it, I installed XEN Xitrix and I have no issues like that.
View 2 Replies
View Related
