Fedora Installation :: White Macbook 5,2 Grub Lockup - Hang At Blank Screen
Jun 13, 2009
[code]...
when trying to choose the Linux partition, I found that it would just hang at a blank screen. Looking further into the problem, I had booted with the Linux Rescue and checked the /boot/grub/grub.conf file. It appeared to be that the menu was set to hidden. I got rid of that line, and checked the boot arguments. It still had acpi=off set with the kernel and everything else seems to be in order. Root is set to root (hd0,2) which should be correct.
Ive recently built a music server with the following configuration:
AMD Athlon 64 X2 5200 processor Gigabyte GA-MA74GM-S2 Motherboard with 2GB ram Western Digital Caviar Green 1TB SATA Hard Drive Samsung 22X CD/DVD Burner IDE
I would like to be able to run Fedora 10 (and Vortexbox, an application to burn and store CD�s) but have been unsuccessful in getting F10 to load. I am a novice Linux/Fedora user. I've been able to load and run Windows XP on the server with no problem. I have downloaded and verified both the x86_64 DVD and the x86_64 Live CD from the Fedora website. With the live CD, the last thing that appears before the screen goes blank and the install freezes is the blue line changing to white. I have tried several different SATA configurations , have turned off all non essential options in BIOS(ethernet, USB support), and have tried loading with fail safe bios settings.
I install the fc11 from Fedora-11-i386-DVD.iso. The software update has just updated my fc11 kernel from 2.6.29.6-217.2.3.fc11.i686.PAE to 2.6.29.6-217.2.7.fc11.i686.PAE. If I boot using the new kernel, The screen resolution is not correct (everything gets bigger) and the screen goes into blank white screen suddenly after log in.
I have a geforce 8600gt card and installed its driver (for pae kernel) as suggested on this link: [URL]Everything goes well untill I update the kernel.
So everything went fine in my installation of ubuntu 10.04 but when the pc was reset after installation, it goes to the black screen with the white writing and then does nothing. To check if there was a problem with the disk I had burnt, I installed an an older version of ubuntu (8.something) which had previously worked and the same thing happened: installation goes fine but then when I reset it goes to the black screen with white writing and does nothing. I then tried to install 10.04 again through usb with the same results. Do I need to change a BIOS setting?
I just upgraded to Ubuntu 10.04 LTS from 9.10. After the upgrade process, I restarted and chose "Ubuntu, with [the current kernel]" and now I am greeted with a white screen with no login or boot splash. My processor is pegged according to the processor case light. My computer's specs are as follows: AMD Athlon X2 5200+, ATI Radeon X1300 Pro, 2GB DDR2 ram, Dell Socket AM2 Motherboard, and 250 GB 7200 RPM hard drive. I really need to get this computer to work.
Recently i had migrated from windows 7 to fedora 15. i have lot of flipbooks with me and unable to open those flipbooks in fedora. finding a suitable solution to open those flipbooks. is there a software to open these books linux. in windows there is no requirement for special softwares to open flipbook, since it is similar to flv or swf files. i had already tried with wine. with wine the file is opened but do not displays the contents or pages, show a blank white screen. @people who dont know about flipbooks: flipbooks are flash objects usually created from pdf files used for reading, flipbooks simulate the reallife book actions(page turning).
This is probably not possible, but just wondering, restarted centos 5.2 remotely, hung at shutdown, kvm'ed to see what was hanging it up, control c'ed and then ctl alt del, just trying to kill the process, was brought back to the login screen, but unable to type anything. Alt-f1 switched to a different virtual console, which was just a blank screen and a blinking cursor, but now able to type things. Want to avoid hard shutdown. Is there anyway to force shutdown/reboot the machine from this console?
I am running karmic on a MBP 5,2. When I close the lid, nothing happens. The screen does not blank, machine does not sleep... nothing. I thought I performed all the steps in the sticky, and I didn't see anything special regarding power management. The power management tool does not list any settings for lid closed.
I'm relatively new at Linux, and I am trying to get Nagios to work correctly. I'm running CentOS if that matters. I think I followed the directions here correctly, but all I get is a blank white screen after I login. The documentation page works fine, but I don't see anything on the main http://localhost/nagios page. I have looked at other solutions to this problem (adding the correct path to the open_basedir in /etc/php.ini) and that still did nothing. Any Way to decode my httpd logs... Any time I refresh, I get these four errors from /var/log/httpd/error_log:
[Mon Jun 06 09:56:15 2011] [error] [client 127.0.0.1] PHP Warning: require_once(/usr/local/nagios/share/includes/../config.inc.php) [<a href='function.require-once'>function.require-once</a>]: failed to open stream: No such file or directory in /usr/local/nagios/share/includes/utils.inc.php on line 4, referer: http://localhost/nagios/ [Mon Jun 06 09:56:15 2011] [error] [client 127.0.0.1] PHP Fatal error: require_once() [<a href='function.require'>function.require</a>]: Failed opening required '/usr/local/nagios/share/includes/../config.inc.php' (include_path='.:/usr/share/pear:/usr/share/php') in /usr/local/nagios/share/includes/utils.inc.php on line 4, referer: http://localhost/nagios/ [Mon Jun 06 09:56:15 2011] [error] [client 127.0.0.1] PHP Warning: require_once(/usr/local/nagios/share/includes/../config.inc.php) [<a href='function.require-once'>function.require-once</a>]: failed to open stream: No such file or directory in /usr/local/nagios/share/includes/utils.inc.php on line 4, referer: http://localhost/nagios/ [Mon Jun 06 09:56:15 2011] [error] [client 127.0.0.1] PHP Fatal error: require_once() [<a href='function.require'>function.require</a>]: Failed opening required '/usr/local/nagios/share/includes/../config.inc.php' (include_path='.:/usr/share/pear:/usr/share/php') in /usr/local/nagios/share/includes/utils.inc.php on line 4, referer: http://localhost/nagios/
I downloaded the Fedora 11 KDE livecd, installed it, and after the reboot when I get to that "firstboot" screen, I can't move the mouse, the keyboard doesn't work, I have to hold down the power button to turn off the computer.
I have an HP computer nvidia and AMD stickers on it and 1GB RAM. HDD is Parallel ATA. I downloaded both Ubuntu & Kubuntu Live CD. Both live CD's boot to a blank screen. After a (seemingly) successful install of kubuntu, the screen goes blank after GRUB.
Here are the details: With this HP, when i boot from ubuntu live CD the screen goes blank. It does not give any option about trying ubuntu, install, ubuntu, mem test. I just get a blank screen. On my ASUS laptop the ubuntu live CD goes straight into ubuntu live (without having to choose an option). It is not the CD When I boot from kubuntu live cd i get to the screen where i have an option to try kubuntu, install kubunt, memtest..
If I choose either try or install, my screen just goes blank & never progresses. Again, this live CD works on my ASUS laptop. At the bottom of the boot screen for the kubuntu live CD i noticed f1-f6 configurations. I was unable to change any other than language and f6 options. If I press f6 i get options which i can mark with an x. I don't know what any of these mean but I checked all of them and then on the boot menu popped up
BOOT **a whole bunch of text** I went onto install kubuntu and it no longer went to a blank screen. Rather it was a fuzzy grainy splash with the word KUBUNTU and loading dots underneath. Atlas it seemed to prevail, the installation process started (fuzziness went away). The installation screen now looks just as it did on my ASUS laptop. I continued through the steps with an installing on the entire HDD. The installation completed (with no signs of error). Screen said take out disc press enter.
I did so and my computer turned off. I power up the computer and the GRUB loads up. I have option of regular and fail safe. Both lead up to a blank screen. My monitor seems to think there is no signal and goes into standby mode. Perhaps the video card is not rendering correctly or not compatible.
I am trying to install kubuntu on my macbook. I am able to boot from the CD and install fine, but when I try to boot from the linux partition the cursor blinks for a while, then the screen goes blank.I have used the rEFIt partition utility, but when I try to reinstall the grub bootloader as described here: it says "sudo: grub: command not found"When it try "grub", it says:"The program 'grub' is not currently installed. You can install it by typing:sudo apt-get install grub"
Just installed Ubuntu 9.10 64 bit on my computer dual booting with 9.10 32bit. Was hoping to move to 64 bit to get full use out of my RAM and CPU. The issue is that when I tried to run Compiz-Fusion that I got from the Ubuntu software repos that came with 9.10 nothing would change. I tried to make a 4 desktop layout with a cube like I have on the 32 bit OS and nothing happens. So I right click on the Compiz icon and select the "reload windows manager" tap in the drop down menu and every time it turns to a blank screen of white with a mouse on it. I can move the mouse and I can even use some of the new settings I changed but I cant see anything else besides a mouse and the white screen. I feel as thou I am using a version of Compiz that is not compatible with 9.10 64 bit.
First let me describe my system setup. I have windows, ubuntu 64 and ubuntu 32 present. I upgraded the 32 bit version to 10.4 with no problem. After upgrading the 64 bit version is when the problem occurred. I believe it has to do with the grub.cfg file. When I would choose the 64 bit version the screen would just go black, no furthur action. After making a few changes to the 64 bit selection in grub.cfg i come to a screen that says c to continue, s to skip mounting, and m for manual mount. Pressing s gets me in. Here is a copy of my grub.cfg.
# # DO NOT EDIT THIS FILE # # It is automatically generated by /usr/sbin/grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub #
I downloaded Ubuntu 11.04 yesterday. The ISO allowed me to install Ubuntu using Wubi and it worked just fine in Windows (I used a virtual drive to mount the ISO). I liked it enough to want to replace Linux Mint on the Laptop with it.After a LOT of trying, I was finally able to make the liveUSB of Ubuntu 11.04 32-bit version.[URL]isplays the boot menu and if I select 'try Ubuntu without installing', I am greeted with a blank screen which just does not go away until I hard reboot the system. Also, the grub I am getting is NOT the purple one which usually is the default; instead, its a dark screen with a black-n-white titled Ubuntu logo. So the question of using the NOMODESET doesn't arise at all. I am using Dell XPS 15 with dual OSes - Linux Mint and Windows 7. Both Mint and 7 are 64-bit OSes but I am trying to install Ubuntu 11.04 32-bit version.
I am installing 11.04 on a Gigabyte E7AUM-DS2H with an onboard GeForce9400. I'm trying to turn this into an XBMC htpc. I'm not using xwindows or anything like that. Going straight to console for now. I'm experiencing the GRUB Black/Blank screen. I just don't know what else to try...
1. I've changed the kernel boot options, i.e. nomodeset 2. I've toggled the GRUB_GFXMODE=640x680 line 3. I've remembered GRUB-UPDATE 4. I can get into GRUB menu using SHIFT at bootup, messing around with settings and CLI there 5. I started with default nvidia drivers (not good), and then installed nvidia-current - that works better. 6. At the blank screen, I can hit ALT-F1 into console/tty fine. 7. If I use nosplash --verbose, I get a long wait with a blank screen, then the last bits of the bootup log and the login prompt. 8. And stuff I've forgot I've done....
Now what I really can't understand is that I have XBMC installed AND working beautifully. I can set XBMC to autorun with no trouble at all. It's just the period between bios and XBMC that it all goes dark. When I quit XBMC, I get a blinking cursor, which I can F1 to the console. What is it with GRUB??? What am I missing? Why is this so difficult? I COULD live with it, but its just not right, and I want to get it right.
I recently wanted to install ubuntu 11.04 on my computer (which had vista on it and I wanted to just completely wipe that out). After the install I noticed that my monitor would not receive signal during boot (I heard the little drum noise but my monitor said no signal). So I tried following these instructions (which have worked in the past): [URL]
but when I boot the computer I don't have a GRUB menu! It just automaically starts booting ubuntu 11.04. Is this because that is the only OS I have installed? Did I do something wrong? What can I do to fix the problem?
I have installed "plug and play" webcam logitech c270. Audio works fine. I can see and hear when people call me. People can hear me, but not see me. On the Skype/Options/Video the "test" button for video results in blank white screen.
I've just installed ubuntu 9.10 from a live cd on to a 2nd HDD, with vista on the 1st. When I turn my PC on GRUB comes up and I can select ubuntu or vista, vista works but when I try to boot ubuntu the screen goes black with a small flashing underscore in the top left and then just goes completely black, nothing else happens after this. I've tried reinstalling from the live cd but when I go install nothing happens and the screen goes black again. When I was installing I changed the boot to something like scsi?
My PC's specs are: Dell inspiron 531 HDD1: Ubuntu(300GB) HDD2: Vista(1TB) OS Windows vista Graphics card. ATI radeon HD 4700 series
I am trying to install Ubuntu Server 10.10 on a computer with 5x 1.5 TB HDDs. I went through the process of partitioning the five hard drives into three partitions each:
sd*0 is a 300MB partition for /boot, RAID1, 2 active, 3 spare sd*1 is a 500MB partition for swap, RAID1, 2 active, 3 spare sd*2 is a 1.5TB partition for /, RAID5+LVM, 5 active, 0 spare. md0 is the raid1 on sd*0 md1 is the raid1 on sd*1 md2 is the raid2 on sd*2
During the install, everything seemed to work fine with the formatter, but the installation ended in error. I booted into rescue mode and found that though all the drives were U (in /proc/mdstat), it was resyncing. I let this run (overnight) and the next day, jumped back in and installed the OS successfully.
However, after installing GRUB, when the installation process asked me to reboot, the system came back up with a blank screen (blank, save for a blinking cursor) and didn't move from there. I am thinking that the problem is GRUB, since I can boot into the main LVM partition via the rescue option on the install cd. Here's what bugs me:
I installed ubuntu 10.10 alongside Win7 recently, absolutely new to this OS.
Experiencing problems with firefox browser. A plain White blank screen appears only with the titile bar named Firefox. Actually when the web-browser icon is clicked, just a cursor BAR appears stuck inside the extreme left end of the screen (cursor bar something like the one we find in word processors or this blinking line while I type this). I manually have to expand the bar in order to get the firefox browser, which is the plain white screen.
Initially had problems with the missing wireless firmware, reading through this forum I activated the Broadcom driver. But before that, I wired in my laptop to the router and then FIREFOX worked fine, after an update which installed bout 214 updates the firefox got conked.
this is my first time doing a custom partition, I tried to do it with only the assistance of reading as I go, but I don't believe I found enough information last night. What I am trying to do, is put openSUSE on 200gb out of 500gb space on my external hard drive, as well as on 50gb space out of 110gb on my internal hard drive. The remaining 60gb space on my internal drive is going to be for microsoft windows. The remaining 300gb space on my external drive will be storage space. It seems like what I want to do is achievable
What I want is to have my main openSUSE on the external drive (primary partition I think?), with the GRUB loader so that when the external drive is not plugged in, my little brother can use windows on my internal hard drive. I tried this last night, and when installation had finished, I rebooted my computer and the screen was just blank black with the flashing white line as if waiting for me to type, although it would not allow me to type when I tried. It would be great if someone could tell me the order in which to partition, including the terms primary partition, extended partition, and logical partition, as needed.. I don't want to permanently muck up this machine.
I am having trouble getting FEdora 15 running on my MacBook Pro. I had Fedora 15 installed before on this MBP before, so I know it works. I basically followed the good old instructions of
1. Create a Windows partition in bootcamp (rEFIt was already installed from trying to get ubuntu running) 2. Boot from disk and install in Windows partition with bootloader on installed on the / partition 3. Install, reboot, and resync the MBR using rEFIt partitioning tool 4. Shut down the computer and start up on the parition you installed linux on
I have just updated to 10.04 on my Dell Insperon 8200 laptop, and all seems well with Linux.My problem is that although it shows in Grub Windows XP will not load. I just get a blank screen with a flashing cursor.I have tried to grub-mkconfig and grub-update, both of which reported successful results.However on reboot I still get a blank screen for windows.This was not an issue with 9.04 and 9.10.so I don't think it is the machine.
I have a Gigabyte GA-MA790FX-DS5 with an AMD Athlon 64 X2 and 4GB RAM. The MoBo does not have embedded video. My main video card is a Diamond Radeon HD3650 PCIe. I was unable to initially install F 10 as the screen would blank out (Black Screen) after it would start Anaconda. I attempted to boot using the suggested option of nomodeset with no change of symptoms. I then switched out to an older PCI video card (NVIDIA GeForce FX5200) and was able to go through the install. Now I am attempting to switch back to my preferred card (HD3650) and just before the GDM screen appears the screen goes to solid white and no ability to switch to another VT. I have been unsuccessful at finding any workarounds for this. I thought the issues were with the older proprietary chipsets pre open source of ATI which was supposedly older than the R500 series, but I guess I'm wrong.
complete trying newbie trying to get to grips with linux. Tried ubuntu and didnt like that so someone suggested fedora. I'm having the same problem I had with ubuntu, I get a white screen when trying to load the graphical install after the media test. On ubuntu this was solved by selecting simple graphics mode. Here I have tried the following commands during install with still no luck
The text install just freezes after selecting the keyboard layout so that does not even work. Tried searching for forums but only solutions I could find where the previous.
I am having the same problem, as soon as X tries to load my screen just goes blank. I have an ATI Radeon 9550. At first I tried switching between VGA and DVI as well but upon ruling that out, I switch to my on-board video card and that is working thus far, but I'm trying very hard to figure out a way to be able to switch back. Anyways I'll check back in later on if I have any new information I will post.
