Ubuntu / Apple :: Mac Mini 2010 Blank Screen On 10.10 & 9.04 CD Boot?

Nov 25, 2010

I just purchased a new Mac Mini 2010 to replace my older Mac Mini 2006 Intel. The problem I am having is that when I boot Ubuntu from the MM 2010 CD-ROM the initial menu that allows you to select a language is displayed, but after that the screen goes blank and stays blank. I am using the HDMI port to DVI output and I am wonder if that could be a cause of the blank screen. Is there a boot command that I can use to allow Ubuntu to display with the HDMI port or other item I need to fix to get Ubuntu CD installer video display to work with my MM 2010?

View 1 Replies


ADVERTISEMENT

Ubuntu / Apple :: 10.10 And 10.04 Won't Boot On Mac Mini (mid-2010 Model)

Mar 10, 2011

I've been attempting to boot Ubuntu on my Mac Mini with absolutely no success. I tried 32-bit and 64-bit versions of 10.10 and 10.04. In all cases, I see the little keyboard and man at the bottom of the screen and then the screen goes black (i.e. my monitor stops receiving input).

My monitor is connect via the HDMI-to-DVI convertor, so is this a driver issue related to that?

View 3 Replies View Related

Ubuntu :: 10.04 - 2010 New Mac Mini Dual Boot OS X 10.6

Jun 16, 2010

The new Mac Mini has just been refreshed. I'm thinking of getting one as a general admin machine, as they run very quietly. I'd like to able to dual boot it with Ubuntu 10.04 and I have a few questions. The hard-drive is 350gb. Would it be possible to dual boot with OSX on two fairly small partitions, say 50gb for each OS. Leaving a remaining partition of around 250gb to keep files on for both OSX and Ubuntu? I've read about this for windows/ubuntu dual boots, but can't seem to find much on OSX/Ubuntu dual boots and whether you can share files easily between them and having common drives for data storage. Also, general tips on dual booting a Mac Mini with Ubuntu 10.04 would be welcome (not a lot out there that I can find).

View 8 Replies View Related

Ubuntu / Apple :: Blank Screen On Imac 27'' I7?

May 16, 2010

I have an imac 27'' i7 and cannot get to install ubuntu.

I always get a blank black screen when during installation even when I select the "safe graphic mode". During installation, the i get some multi-colored straits at some point and then nothing, it returns to the black screen.

I even tried to partition my hard drive with Gparted and got the same blank black screen even with the "safe graphic mode" option.

View 9 Replies View Related

Ubuntu / Apple :: Blank Screen After Kubuntu Loads?

Jan 17, 2010

imac g3 power pc screen goes blank and the power button goes orange after kubunto loads, but the computer is still running, how do i fix this problem, if you have any information please be very spesific i have no idea what im doing so include all steps, thanks to anyone who posts (if this helps the computer makes the drum roll noise if i hit enter but the screen still stays blank)

(xbuntu version -xubuntu-8.10-alternate-powerpc)
(system informaiton...
(powerPc G3 266MHz/512k catche/32mb/6gb HD/24x CD-ROM/rage Pro/6MB SGRAM)

View 3 Replies View Related

Ubuntu / Apple :: Blank Screen After Xubuntu Loads

Jan 18, 2010

my imac g3 power pc screen goes blank and the power button goes orange after Xubunto loads, but the computer is still running, how do I fix this problem, if you have any information please be very spesific I have no idea what im doing so include all steps, thanks to anyone who posts (if this helps the computer makes the drum roll noise if I hit enter but the screen still stays blank)

(xbuntu version -xubuntu-8.10-alternate-powerpc)
(system informaiton...
(powerPc G3 266MHz/512k catche/32mb/6gb HD/24x CD-ROM/rage Pro/6MB SGRAM)

View 9 Replies View Related

Ubuntu / Apple :: Macbook Pro Won't Blank Screen When Lid Is Closed?

Feb 25, 2010

I am running karmic on a MBP 5,2. When I close the lid, nothing happens. The screen does not blank, machine does not sleep... nothing. I thought I performed all the steps in the sticky, and I didn't see anything special regarding power management. The power management tool does not list any settings for lid closed.

View 2 Replies View Related

Ubuntu / Apple :: Karmic On 5.4 Blank Screen After Upgrade

Mar 23, 2010

im running karmic on a macbook pro 5.4. everything worked fine for a couple of months until i upgraded yesterday. (apt-get upgrade) now i'm getting a blank (black) screen when booting right after the splash screen appears tough the system comes up propperly since i can connet using ssh. the xserver is up and running regarding to the logs. i can't even switch to a console (alt-crtl-f1) nor booting in single user mode. the screen gets black after the kernel boot and init starts.

View 5 Replies View Related

Ubuntu / Apple :: 10.10 IBook G4 PPC Blank Screen After Installation?

May 17, 2011

I installed Ubuntu 10.10 alternate PPC on my iBook G4. I have to used this command upon installation or else it went to white screen which doesn't go away:

install video=ofonly

Installation went smooth till the end.

After reboot, it did prompt me to pick l or c, then yaboot screen appear. However, after I entered 'Linux' and hit Enter, nothing happened - blank screen.

View 9 Replies View Related

Ubuntu / Apple :: IMac G4 Blank Screen While Booting Into Lucid

Apr 26, 2011

I downloaded Ubuntu Lucid...something onto a cd and I booted into it on my iMac G4. It brought me to a screen saying things like live is default press tab for more options etc and when I just press enter, the screen turns white, loads a few things, then it turns blank and after awhile, I hear the Ubuntu startup sound but my screen remains blank.

View 2 Replies View Related

Ubuntu / Apple :: Blank Screen When Booting From Kubuntu Partition On Macbook?

Feb 3, 2010

I am trying to install kubuntu on my macbook. I am able to boot from the CD and install fine, but when I try to boot from the linux partition the cursor blinks for a while, then the screen goes blank.I have used the rEFIt partition utility, but when I try to reinstall the grub bootloader as described here: it says "sudo: grub: command not found"When it try "grub", it says:"The program 'grub' is not currently installed. You can install it by typing:sudo apt-get install grub"

View 4 Replies View Related

Ubuntu :: Blank Screen On Boot / Very Fast Plymouth Screen

Jan 14, 2011

I fixed this issue on 10.04, but just recently (1 hour ago) upgraded to 10.10 and am having the same issue. Machine boots fine, but the screen is blank for most of the boot, and plymouth is up for about a half second before I get to the login screen.I've tried searching the threads, but for the life of me I can't find the solution and can't remember what I did to fix it on Lucid.

View 4 Replies View Related

Ubuntu / Apple :: Getting A MacBook Air 11" Late 2010?

Dec 25, 2010

I'm getting one of those an 11" MacBook Air with 128gb SSD. 64gb might be too little for dual booting. Of course, I'll run Ubuntu on it. I'm choosing this hardware, because of the great form factor, aesthetics, trackpad, and ability to run OS X (as a UX designer, I want to do competitive analysis of the OS).It will be my first Mac. Any advice? Got tips on what I should start learning, getting used to, etc?

View 3 Replies View Related

Ubuntu / Apple :: IMac 27 2010 - Microphone Doesn't Work

Nov 11, 2010

I bought an iMac 27" 2010. Now I installed Maverick but neither the iSight microphone nor the one you plug into the jack works. How can I do?

View 1 Replies View Related

Ubuntu Installation :: Blank Screen: 10.04, ATI Radeon 9550 / X Tries To Load Screen Just Goes Blank?

May 9, 2010

I am having the same problem, as soon as X tries to load my screen just goes blank. I have an ATI Radeon 9550. At first I tried switching between VGA and DVI as well but upon ruling that out, I switch to my on-board video card and that is working thus far, but I'm trying very hard to figure out a way to be able to switch back. Anyways I'll check back in later on if I have any new information I will post.

View 3 Replies View Related

Ubuntu :: Blank Screen At Boot?

Nov 13, 2010

Just upgraded from Karmic to Lucid.. Everything was running smoothly except compositing so I enabled the Open Source Edge repos and downloaded the latest driver my card (a ati radeon x1650). I rebooted to a bios splash and then nothing.. blank screen. After about 4 seconds of nothing the monitor flicks on showing the kubuntu bootsplash for a split second then blank again.ctrl + alt + f$ isn't displaying a tty for meI'm not getting the usual grub menu on startup (esc isnt bringing it up)(it's a usb keyboard enabled in the bios)

View 3 Replies View Related

Ubuntu Installation :: Dual Boot With Windows 7 - Blank Screen With My TFT Screen Displaying A Msg "Out Of Range"

Jul 8, 2011

I have installed Ubuntu 11.04 along side windows 7 ultimate. But the problem is as soon as I switch on my computer. There is only a blank screen with my TFT screen displaying a msg "Out of Range"

Then suddenly Ubuntu loads without showing any option to load windows 7.

View 2 Replies View Related

Ubuntu :: Upgrade From 9.04 To 9.10 - Boot Up (Blank Screen)

Apr 7, 2010

Last night I upgraded from 9.04 to 9.10 in search of faster internet (which I got by the way), but now whenever I try to boot it goes to a blank screen for about 10 minutes befor going to the desktop. Its completely blank and has no cursor or anything. It's a huge problem and I could really use some help. 9.04 never did this.

View 9 Replies View Related

Ubuntu Installation :: Blank Screen On Boot Up?

Oct 16, 2010

I have a blank screen on boot up. Has happened since 10.04.It's this problem[URL]I tired their three solutions did not work however clicking F6 and slecting nomodeset before booting got farther then ever and then saidI have tried different images, betas RCS full versions, netbook, derivatives and its all the same.hats going on? Can it be fixed and is this always going to happen now or is it just a two cycle bug?

View 3 Replies View Related

Ubuntu Installation :: Blank Screen On Boot?

Nov 1, 2010

I have a HP EliteBook 2730p. lspci reports this for my graphic card:

Code:
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device 30eb
Flags: bus master, fast devsel, latency 0, IRQ 30

[Code]....

I updated from Lucid to Maverick. When I boot with the new 2.6.35-22 kernel the screen stays blank after grub. When I boot the old 2.6.32-25 Kernel everything works fine. I tried to boot 2.6.35-22 in Recovery Mode. When I do this I see some kernel messages in text mode and then the screen goes blank again.

View 1 Replies View Related

Ubuntu Installation :: 10.10 Does Not Boot - Blank Screen

Nov 15, 2010

I upgraded 10.10 from 10.04 from the update button from within the update manager. It seemed to upgrade ok but after I shut down and turned it back on it goes to a blank screen. If I then hold the power button to turn it off and back on it then loads to a boot screen where about 6 options with recovery option are listed. The top 2 options do not work as they just go to a blank screen but the bottom 2 give me some other choice including seeming to boot up to a normal Ubuntu environment. How can I fix it so that it boots to a normal Ubuntu 10.10.

View 8 Replies View Related

Ubuntu :: Blank Screen With Dual Boot?

Nov 18, 2010

I have always had Ubuntu installed along with Win 7 but rarely use it, i only use it if i am flashing firmware to my phone or something similar.

I uninstalled my older version of Ubuntu because it was becoming sluggish and have tried to install the 10.10 version a few times today, but every time i boot into Ubuntu, i get a blank purple screen and nothing else.

My mouse curser is the only thing that is working but there is nothing to click on and nothing shows if i right click.

View 4 Replies View Related

Ubuntu Installation :: Blank Screen On First Boot

Mar 22, 2011

I have a toshiba satelite pro laptop (can't think of the exact model at the moment) with 4gb ram + 320gb hard drive. i have been dual booting ubuntu for roughly a year, and throughout all that time windows has become less and less used, therefore last night i took the plunge, and went about installing ubuntu(10.10) as my main operating system and removing windows, i did this via a usb, using Unetbootin.

I used one of the .ISO's from the official ubuntu site, and went through the installation processall went well, no errors within the installation process, hard drives were partitioned fine etc, however when i've come to turn my computer on for the first time this morning i get a black screen with a blinking underscore straight after the toshiba logo flashes up and i get the choice to go to bios options.

If i do go to bios options my hard drive is listed fine, and if i try to boot from my usb again, it doesnt work, and attempts to verify dhcp and eventually tells me it couldnt find a boot file, my laptop however is plugged in via an ethernet cable. it doesnt work with or without the ethernet cable. i have tried leaving it for about half an hour and nothing has changed, i also can't boot to GRUB.

View 2 Replies View Related

Ubuntu :: Try To Boot Like Normal / But Then A Blank Screen

Jun 25, 2011

I just finished installing 10.4 on my Dell Latitude X300, and it will only run in low-graphics mode. I will try to boot like normal, but then a blank screen. I have to boot in Recovery Mode and use the Failsafe graphics option.

View 4 Replies View Related

Ubuntu :: Only Boot With Black / Blank Screen?

Jul 9, 2011

so I had a black screen when I was starting up my PC instead of the normal Ubuntu with the dots underneath. I have Ubuntu 11.04 on a dual-boot with Windows Vista. It would still boot normally and work fine but I wanted it with the Ubuntu and dots etc.

After looking at many sites to try and fix it that didn't work I found this: [URL]. That didn't work so I found this next: [URL]

I did what it said by removing

Code:
vt.handoff=7

Then when rebooted I got the Ubuntu with the purple background and dots but the boot would hang (always when all 5 dots were orange). I booted into recovery mode and I chose "File System Check" on reboot and it would get to the bit with 5 orange dots then it would check disk for errors and go to login screen then work fine.

If I added vt.handoff=7 it would boot normally with a black screen again.

RESULTS.txt is from when I had vt.handoff=7 removed and I was in Recovery mode>resume normal boot>"sudo bash ~/Desktop/boot_info_script.sh".

RESULTS1.txt is from when I booted up with the disk check and was in Terminal.

EDIT: Also just recently I'm getting a lot of boot hangs, freezes (where everything on screen will freeze and if I was playing music in Banshee it repeats the last 3 seconds until I hold down button on PC), and it will sometimes just restart randomly. Not sure if that related or not...

View 9 Replies View Related

Ubuntu / Apple :: Shows Only 1 Core For Mac Mini 3.1

Mar 31, 2010

I noticed that ubuntu only detects 1 core on a mini 3.1 dual core. Has anyone the sam issue? Or has someone an idear an what's happening. Already tried 32 bit and 64bit.

View 9 Replies View Related

Ubuntu :: LiveCD - Install And Boot - Blank Screen

May 4, 2010

I installed a new graphic card from ATI 5770 (Club3D). After I did it I removed the propriatery ATI drivers I had installed thru the "Hardware Drivers" in Ubuntu and rebooted. Then I couldn't get into ubuntu again. When it starts booting the display just shuts down and says "Power Saving mode". The computer continues to load things etc. left it running and hoped it would show itself... nothing.

Anyway this happens everytime even with Live CD so I can't even get to a terminal... Started the boot without the splash and it went blank after it started some Speech thing. Just before that there were a few firmware files missing.

View 8 Replies View Related

Ubuntu Installation :: Lucid Blank Screen On Boot

May 10, 2010

when booting my system, I get sometimes a blank screen. I searched around and couldn't find a proper solution. ATI Technologies Inc RV535 [Radeon X1650 Series] The only option I have is to reset the PC and hope for it to boot without the blank screen...

View 2 Replies View Related

Ubuntu Installation :: Blank Boot Screen And Consoles

May 27, 2010

I have got myself into a situation where I see nothing during boot until X starts, and I have no text virtual consoles. I recently replaced my old 9.10 system running on hardware that seemed to be breaking down, with a new system with both an onboard graphics chip (which I disabled in the BIOS as the 1st step), and an Nvidia GeForce 8400 GS card. I installed Windows XP then Ubuntu 9.10, copied all my files across, modified /etc/fstab, /etc/hosts, etc etc., and as the last step I unplugged the 1920x1440 IBM CRT that I'd used during the install and tweaking, and plugged the display into the BenQ LCD on a Belkin 4-port KVM. Oh, I also installed Windows and Splashtop (that mini-Linux that fast boots from the Windows NTFS partition).

I had a problem at that point: I had a lot of trouble getting any signal on the LCD monitor, and eventually got it working but with the whole display half-shifted off the screen (everything was shifted to the right about six inches), and the Ubuntu splash during boot (the sort of spotlight effect with the glowing horizontal line with the light animating along it left and right) was shrunk and only occupied part of the screen. Nor could X detect what kind of monitor it was. I had a lot of problem with a lot of attempts prodding the LCD monitor to complain "Out of range!" (over the top of the Ubuntu three linked circles). I couldn't fix the problem, and in the end installed the Nvidia proprietary driver and ran its X configurator, and suddenly everything snapped back and began working correctly: X ran happily in 1680x1050, filling the screen properly, and X could now correctly detect the monitor as a BenQ.....

View 6 Replies View Related

Ubuntu Installation :: 10.04 Server - Screen Goes Blank After First Boot

Jul 14, 2010

I've installed 10.04 Server on a desktop three times. The install goes well and after the installation, the server reboots and I can login with no problems. I can also look around the file system and run some of the utilities. My network can also see the server. The problem comes when I restart the server for the first time after the installation restart. The system starts to come up and then the screen goes blank. The computer is still running but there is no video signal to the monitor; and the network cannot see the system. I believe this has something to do with the master boot record but I'm not sure.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved