Slackware :: Slackware + Other Distros Networks Boot With PXE?
Oct 3, 2010
I successfully managed to install slackware on a laptop with a broken optical drive, no floppy drive and no option to boot from USB stick, with the invaluable help of AlienBOB's guide: some of the packages could not be installed during the installation. The fatal errors seems to occur randomly and the packages that I later had to install by hand were the following:-git-java (can't recall exactly what it was about)-linux-howtos-kdebase-workspace
Im trying to install a multiboot with multi distros, in this case Slackware and Linux Oracle. I have Slackware running for a while now and try to install it in other partition. Suppose I have Slackware in /dev/hdb and planning to install Oracle Linux in /dev/sda. My plan is:
1.Format /dev/sda 2.Install Oracle Linux in /dev/sda using boot disk 3.Modify lilo.conf 4.Run dual boot
But the problem is during the Oracle Linux boot installation: 1.It doesnt recognize the partition and file format that Slackware did in /dev/sda 2.The installation disk then force me to create another partition for memory swap and root directory 3.At first attempt I created a partition in /dev/sda with RAID format which didnt get recognized by Slackware so that I had it wiped out at the next attempt of installation.4.Just before the process of partitioning /dev/sda, Oracle Linux installer from the boot disk cannot detect my dvd drive although the PC was booted from its very drive (Why?) so It was asking me if I need to point out the location of another copy of the image file, which is located in /dev/sda1. The installer read it from /dev/sda1, I think not from DVD drive. This always happens in all attempts.5.At the end, it cannot finish the process of the installation and I have to abort it, without knowing the reason for it. This happens in all attempts also.
I try to install Slackware to my IDE hard drive and boot first from Slackware DVD. After I loaded huge.s kernel, and tried to partition the hard drive using fdisk by entering "fdisk /dev/hda", I found out that the partition size is max to 3 Gigs instead of 80 Gigs.
I think the kernel is looking at my boot disk, which is around 3 Gigs. How can I make so that it looks at my IDE drive instead at my boot drive? Is there any manual that shows me how to install Linux from scratch this means I want to wipe out all my hard disk and install Slackware Linux there?
I'm trying to install Puppy 525 on my Slackware 13.37 PC as a dual-boot using LILO. Puppy is living, all on it's own, in sda6, a 6 GiB partition. It got there by using the Puppy Universal Installer and selecting a 'Full' install, not a 'Frugal' install. I cannot find 'LILO' type instructions, only 'GRUB' type instructions.
Has anyone succeeded in doing a hard drive install of Puppy with the LILO boot loader?
Edit: I'll probably regret it, but I used Puppy's GRUB installer.
I installed Slackware 13.1 and Windows server 2008, I also installed LILO in MBR, I Found I can boot into slackware, but can't boot into Server 2008. then I　use command bootsect/fixmbr. now I can boot into server 2008, but the problem is I can't boot into slackware. I try to install lilo to supper sector. it's not works. I only can boot my slackware by a USB stick.who can help me to solve this problem? I really need these two systems.
I updated my kernel in slackware current but can't install lilo, when i was with my old kernel it gave an error about not finding the sda drives (they were named hda before the upgrade).I booted into the slackware 13.0 dvd and modified fstab and lilo.conf replacing hda with sda but lilo still gives an error of not finding sda drives.How can i install lilo so i can boot into my sistem??
I just did a fresh install of slack 13.1 on a separate drive to the one I was previously using. I've been having trouble getting lilo to work, so that I can choose between either drive. Lilo is currently installed to /dev/sda, with the old system on /dev/sda1 and the new installation on /dev/sdb1. I keep getting errors like these:
Code: Fatal: Trying to map files from unnamed device 0x0011 (NFS/RAID mirror down ?) I managed to install lilo from the old system by copying the kernel image from the new system into the /boot/ directory and running lilo. I am now on the new system and trying the same thing in reverse but it isn't working. I have searched around a bit and there's a lot of talk of chroot-ing into the other partition to run lilo. I don't understand why the process isn't working both ways though. I can't run lilo on my new installation even with the two kernel images in the local /boot/ folder. Is this something to do with btrfs or am I missing something to do with lilo? This is my lilo.conf file. I am trying to run lilo using this file from my new installation on /dev/sdb1 and getting the error given above.
I've a multiboot machine and I recently installed Slackware64-13.1 on sda33. I added menu entry in SUSE boot loader and configured menu list as per [URL].. it returns GrUB error 15. Here is my menu list entry for Slackware -
Code:
###Don't change this comment - YaST2 identifier: Original name: other### title Slackware64-13.1 root (hd0,32) kernel /boot/vmlinuz root=/dev/sda33 ro hdd=scsi savedefault
My new job requires I use Windows and as such I put a second HDD in my laptop for the purposes of Window/Work The issue is that Windows will not install on this second disc (Windows cannot create partition or install to disc). I got around this by installing Windows to the first disc, then the second then putting Slackware back on the first but then I suffer the "Bootmgr cannot be found, press ctrl + alt + delete to restart".
I am using Lilo and I have never really had an issue dual booting them on the same disc (Admittedly over a year ago) but it is of the utmost important I have them on separate Discs. Has anyone encountered this and/or know a way around?
A friend of mine threw me an OLPC (original model with 1GB of storage) that he was trying to put slackware in. He managed to install a minimal installation, but now it asks for the e2fstools (the stuff to run fsck on ext(2/3/4) partitions) which he didn't install (he formatted the "disk" as a single jfs partition). Is there any reason why it would want to have those tools given that there are no ext(2/3/4) type filesystems in that machine? And is there any specific init script (or udev rule) that can be edited to make it not try and check ext(2/3/4) partitions?
I am running -current on an ASUS eeePC 1000HE. Wireless was working fine up until the time I applied the latest changes from the Slack -current tree, which upgraded wpa_supplicant. Now, no networks are detected.
I looked at some related threads here and did some basic checking: neither the eth1 nor wlan0 interfaces show up in iwconfig or ifconfig output. Am afraid I am still a wireless dunderhead and don't know where to start troubleshooting this issue.
So I got slackware 13 from the website and created 4 partitions (primary) and left some (100GB) space as I planned to install windows 7 in that. After installing slack, when I booted from windows DVD (rtm) in partition section it said I already have 4 primary partition so windows cannot used the rest of space despite the fact that it was free (windows even grayed all options like new partition and format etc. for that space). So I thought I'd create 2-3 primary partition for linux (slackware) so that windows can use the free space and make it a primary partition.
So, Next I formatted with slack (3 partition, 2 Primary, 1 extended, total space for slack 50GB) and after its installation I worked my way with windows, but it just created one partition of 100Gb, won't let me create any saying all primary partitions are created. Anyway, I created that partition and installed windows 7. But it messed up my lilo (slack won't show in boot menu) neither can I create any new partition.
After all I reformatted again created 2 partitions for windows (that actually became 3 as windows 7 create 100Mb separate partition for system). Installed windows correctly. Then I booted with slack , which allowed only creating 1 partition as 3 were already there. So I created 1 extended partition, in which I created 4 partition 1 to mount for /boot (100M), 1 for /swap (3G), 1 for home (10G), 1 for / (35G) everything worked fine till I reached last point to install lilo. At that point it said cannot install Lilo (I tried all options simple, expert, install to MBR etc.) but it just won't install. Anyway, after that it said you can install it manually so I clicked OK. Then it said setup complete, remove disk and press alt+ctrl+del to reboot, which I did. But there is just windows 7, no slack ?
I somehow lost wicd. the icon is still at the bottom of the screen, but show "no networks present.' When I run iwfonfig as root it shows eth0 and lo, but no wlan0. When i run iwconfig, it says eth0 and lo with "no wireless extensions."
I'm trying to take my current windows7 (x64) setup and make it into a dual-boot setup with slackware 13.0 (x32) and am hitting a brickwall. I guess I would like to know if I can salvage the situation without formating my windows drive. I fully intend to, but I had hoped to not do it this month. I'd like to get dual boot going so I can master it and acquire all the files/drivers I'll want and then format and do it 100% right next time.
Currently I have windows setup on a 3x 500gb Raid0 onboard array which itself has been flawless. After I shrunk my current partition size to give me about 25gb of free space I proceeded to setup Linux, and I was unable to perform the cfdisk portion for partitioning the array for Linux.
I tried using cfdisk: /dev/hdx (a1-a3,b1-b3) /dev/sdx (a1-a3,b1-b3)
I even attempted to locate with: cat proc/partition and tried using cfdisk on every device it located. It always said it was either an unknown partition table and should I start at zero, or bad partition. I was of course too concerned over my windows setup (which has almost 1tb of stuff I have not backed up) to go any further into the unknown.
PS: I have used Slackware before, back at 8.1, 10, and even a very brief interlude at 12.0, this is my first attempt on this computer however with 13.0, it is currently running fine on my laptop and my PS3 (Laptop is even dual booting 7/Slack13. Albeit without raid)
Phenom 9850 M2N-SLI Deluxe (Nvidia AM2) 4x1gb of 1066 kingston hyperX 3x500gb WD Caviar Black Sata2 3.0
For various reasons, I have to learn my way around CentOS. I have an old computer (P3) with Slackware on it. I threw in a second HDD that I had lying around and installed CentOS to it. I was figuring that I'd just decline installing GRUB or point GRUB to Slackware as the second OS and end up with dual boot.
The CentOS install, though, blew right past that part with offering me any options. It put a small boot partition on the CentOS drive and now the box boots straight into CentOS.
I've spent the better part of the day trying to get GRUB to boot the Slackware drive and had no luck, though I've learned a lot about GRUB error messages.
By the way, CentOS uses GRUB v 0.97.
Question: someone could point me to a reference.
Here's the output of fdisk -l on that computer (/dev/sda is a 4GB SCSI disk that was originally the boot disk for Windows 2000 server on that computer):
Code:
Here's the currentGRUB file. I added the section about Slackware. I've also tried pointing it at:
Code:
I've also tried:
Code:
Code:
Slackware's LILO:
It's been six months or more since I used this computer. It's my experiment-er "play" computer and I had taken the HDD out to test a computer for one of the members of my LUG, so I can't remember exactly how I configured the LILO install, but, if I did what I usually do, I installed it to the MBR of /dev/hda. I have considered just blowing away LILO, but I'd be happier if I could just use GRUB to call LILO.
I have been given the task to install slackware 13.1 over windows. I have downloaded and copied slackware 13.1 on to a disk, and rebooted the computer, but i am not getting what all the tutorials have shown. I have been looking for tutorials that specifically instruct me as to how to install slackware 13.1 on to a windows xp. I am not trying to dual run I just simply want to run slackware and slackware only.
1: How much does it affect securty, over a lan network? 2: Will it cause any other security issues? 3: The most important is can I forwad X11 from a 32 bit slackware to a 64bit slackware
it's possible to compile the 2.6.37 kernel patched with the autogroup patch on a Slackware 13.1 system running 2.6.33.4-smp with 2.6.33.4 headers? I just compiled and installed the 2.6.37-autogroup kernel from AUR on my ARCH setup and I like it especially when using firefox with lots of tabs open and other background apps also running. I did notice a speed and smothness difference in my ARCH testing setup with this kernel patch and I can get same results in 13.1??
I installed slackware 13.1 x86_64 bit with multilib, and its been about a month already, I'm really enjoying slackware but I am being troubled with my nvidia card, and I need to get my 3D acceleration working. And I've been looking around the net for information and kept on trying to make my nvidia card to work but to no avail. I cant get X to start, once I put in a xorg.conf stating to use the nvidia card. After troubleshooting for almost 2 weeks and now at my wits end, I now come humbly looking for help in linuxquestions slackware community forum.I've installed nvidia 64 bit kernel, drivers from slackbuilds (version 256.44). The laptop model I'm trying to get it working is an -ASUS K52J Intel Core i3 2.40Ghz with 2GB RAM and with an Nvidia Geforce 310M with 1GB dedicated VRAM.
I recently installed Slackware Linux 13.1 , and my Wireless is down. I've only installed 3 Linux disto's on my main laptop (Ubuntu 9.10 , 10.04 , and Crunchbang Linux 9.04 , just had Crunchbang), and they all had the same problem. In all three , I was able to enable Windows Wireless drivers and every thing worked. Now , I'm assuming I have to the same ting in Slackware? Sorry , but I have no idea what my wireless card is. But I know that my laptop is a Dell Insprion E1705. One last thing , I did ifconfig and that wlan0 is my Wi-Fi interface. I typed ifconfig wlan0 up to see if that was the problem. After I did that , I got and error message. Then I typed ifconfig wlan0 down to see if it was down and it made wlan0 down. I tried bringing it up again , but I got an error saying it couldn't find the device specified. Also , how do I install XFCE? I really don't like KDE for some reason and would like to install XFCE. I chose XFCE over GNOME (my favorite) because I want to try something new.
I'm happy to announce Linvo 2009.1 rc6. It's a full-featured Linux distribution with a lot of applications by default, including an office suite (OpenOffice.org extended with plugins), a good internet browser (Firefox extended with plugins), a music player that supports music collection and a lot more - Exaile, a video player, and all the available codecs. It can open all types of file formats. It's a LiveCD, which means that you can test it without installing and after this optionally install it - it has a nice easy graphical installer.
It's the first Slackware-based LiveCD distribution with GNOME by default. It includes NetworkManager and initng in place of sysvinit. It also features accessibility tools. It is also the first release with the innovative portable applications system. This allows you to download application from the site (modules section), place it where you like, and use it. It's just a single file, no directories. You can also use this application without installing it, directly from the internet. However, after this, the speed of the application is limited by the speed of your connection, of course. Check out the "Applications" section on the website.
Besides this, you can install software with the apt-get-like system "slapt-get" and it's graphical front-end: GSlapt. It also contains src2pkg and sbopkg in case you want to compile something from source or existing SlackBuild Depfinder is included to find dependencies of packages. Click here for a guide on how to use those. I also managed to put development tools in there, like GCC, G++, svn, cvs, so on... This is a release candidate, and despite that it's OK for using. It has a bit more things to do until the release (like language selection on the boot menu), but I decided that it's important to put it here for testing.
We are pleased to present one of our new creations: pkgbuild, a tool written in standard C++, using libCURL, ZLib, BZip2 and libLZMA (part of XZ). It is a modern Slackware packages builder, network-transparent, multi-architecture, designed to greatly simplify the creation of a package, automatically executing the required post processing.
What does it do? Recognize and build packages for the following architectures: i386, i486, i586, i686, x86_64, IA64, IA32e, s390, s390x, sparc and sparc64.
how to on enable ling separate X sessions with dual monitors in slackware? In rhel all I have to do is enable it under the nvidia-settings... In slackware it does not work that well... to what I understand you have to configure a separate x session...
I'm trying to bring my Slackware system back to life as my XP HDD is dying... I've got everything working except for my audio. I got a new motherboard (ASRock P43DE3) and it has a VIA VT1708S as the onboard audio. Is there any way I can get this working without rebuilding the kernel?
I noticed that the official Slackware packages don't contain static libraries. The SlackBuild scripts from slackbuilds.org or from Slackware DVD usually contain --disable-static option to prevent building the .a file. And if configure script doesn't allow such option, the .a file is deleted before the package is created.I am wondering what is the reason for that? Is it just the matter of conserving disk space? Are there also other reasons?
I recently bought the Alfa AWUS036h which uses the Realtek rtl8187 chipset. I am able to load the module and connect to any network, but its almost as soon as I try to load a page the connection drops. It never stays connected for more than 30 seconds. My other computers using the same adapter in the same spot work fine, unfortunately there not running slackware. I've tried compiling the newest stable kernel and checked the rd.inet1.conf settings.
I have installed multilib support in my 64bit slackware 13.37 installation than I proceed it to install google earth from slackbuilds... and did ln -sf /lib/ld-linux.so.2 /lib/ld-lsb.so.3Now when I try to run google earth I get:[ 760.092745] googleearth-bin[3647]:segfault at 984f7d31 ip 00000000984f7d31 sp 00000000ffbfe100 error 4
