I installed Slackware 13.1 in a EEE PC 1001px. After the installation I had speaker sound but not using the headphones. Then I ran alsaconf and now I don't have any sound at all!!!
Alsamixer shows the channels: Master - Speaker - PCM - Mic Boost - Mic Boost - Capture.
What can I check to see why this is happening?
I have installed Slackware 13.1 in a ASUS Eee PC 1001PX.
Slackware detect the sound card as a HDA Intel Chip: Realtek ALC259.
The laptop has just one connector that can work either as mic-in/headphones-out.
The problem is that I don't know how to tell Slackware which device I connected (mic or headphones). If I don't connect anything the speakers work but if I connect my headphones I don't get any sound at all.
I've had a snap, crackle, pop coming from my speakers since I put this machine together, even now, with no reason for any sound to be coming from the speakers. Additionally, the crackling only becomes worse when I play ANY audio regardless of player or source, however the sound does just drop for a few seconds and then back and then off again when there is SUPPOSED to be audio. I understand not working at all, but "kinda" working is more confusing.
I'm running slack64 with the with an updated kernel from current, even though the rest of the machine is stock 13_64. The problem was the same with the original 2.6.29.6 kernel.
i did a recent install of slackware 13.1 in my toshiba nb200 netbook and everything is running good, except the sound. i can listen to only one audio stream from one software. if videos (firefox) is playing a video, audacious won't play, and vice-versa. i did some research but i didn't find a solution for this problem.
[code]...
I just installed Maverick, and everythings working great except sound. I only have 2 channels working front left and right, no middle, no rear, no bass. In sound preferences i can only choose between different stereo options.
View 5 Replies View RelatedI recently installed ubuntu 9.10, today actually, and I can't seem to make the audio work. I read a lot of threads, but no luck with this..
View 7 Replies View RelatedWell I installed Ubuntu 10.10 64Bit along side Windows 7, and I've been unable to get any sounds working, apart from the log on sound. So I tried installing some drivers, and now there is no sound at all, and no sound devices show up in System-Preferences-Sound-hardware
I'm using the on board HD Audio (ALC 889A) and using the optical Audio out for 5.1 Surround sound.
I've tried just using the Stereo ( Green Jack ) out, and still nothing. The suggestions on the on the Ubuntu site, and the following post didn't seem to work either.
[url]
I Can't find a great deal of posts with the Realtek HD audio.
I'm running Ubuntu 9.10, but so far I've been unable to get sound to work. I know my sound card is Realtek, because I've had to install the HD Audio Codec Driver when I was on Windows. I downloaded the driver for Linux and it is currently sitting in my home folder. When I tried to Code:sudo ./installthe driver, it failed for the following reason:
Code:
WARNING!!! The mixer channels for the ALSA driver are muted by default!!!
**************************************************************************
[code]....
I was running Ubuntu 9.04 and just upgraded to 9.10 recently. I see many others are having problems with their sound. I too do not have sound. I did get sound running briefly with an Alsa update, but it was muffled. In trying many other fixes, I again have no sound and can not resolve it. I am thinking of burning a new cd and doing a fresh install and starting over.
My lap top is an MSI GT725 US model with an HD4850 mobility graphics card. I dual boot between Vista 32 bit and Ubuntu.
Has anyone else had any luck getting the Realtek ATI sound working in 9.10?
I can't get any sound to come out of my laptop through Kubuntu. Please help me by giving me step by step instructions, because I'm a total noob at such things. I've went through the Comprehensive guide as well -to no avail. to sum it up:
Kubuntu 9.10
Realtek ALC880
No sound
In Window XP, Seven and Vista, to hear good sound, it use Realtek application. Realtek give sound effect such as sound in hall. In accordance with that, I intrigued with sound effect from Realtek application and how I want install sound effect such as Realtek application in Linux? I now using Ubuntu 9.10
View 1 Replies View RelatedI have an MSI S420 with a realtek alc883 onboard. I upgraded from ubutu 8.04 to 10.4 recently, The sound worked in 8.04 although the mic did't work and the same thing in 8.10 (i went through all upgrades) it stopped working at all in 9.04 onwards.
If i did Lspci -v it did say the name of my card, ( I unmuted all in alsamixer and got the codecs but even a test soud won't work) I also dowloaded a driver from Realtek itself, that didn't work.
Then I edited alsabace.conf some more. I tried every one that could possily be it at [URL] including all that said MSI.
I then tried Lordraidens comprehensive sound guide from step 1 to step 5, I used the module-assistant and istalled a driver that was called "hda-realtek-codec" or so. It was the only appropriate one on the list.
I also run into someoe with thesame problem. [URL]
i think ill give up and use the 8.10 that is still on a other partition
I want to install this URL...How to? Because i downloaded the tar.gz2 format of it.And i dont know what to do.
View 2 Replies View RelatedI've been trying to get my surround sound(5.1) to work for the past couple of of days, followed a number of guides, but nothing seems to get it working at all. I'm connecting the speakers using 3 analogue audio cables, I have tested and they work fine under Windows. When I go into the Sound options in Ubuntu I don't see a 5.1 profile listed under the Hardware tab, only stereo(and that works fine).
The sound controller is a Realtek ALC892 built-in to my mobo(Gigabyte P55A-UD3).
Here is some info I've seen requested in other threads, I'm running 10.10 RC, but I can assure you it doesn't work under earlier versions.
Code:
Linux Yurippe 2.6.35-22-generic #33-Ubuntu SMP Sun Sep 19 20:32:27 UTC 2010 x86_64 GNU/Linux
Code:
**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: ALC892 Analog [ALC892 Analog]
[Code].....
Sound works with Jaunty Jackal. Does not work with Lucid Lynx. It appears that Lucid Lynx will only acknowledge that I have a modem as a sound card. I just want to add my RealTek ALC880 driver so the sound will work. I've made sure that I have audio privileges, I made sure that nothing is muted using alsamixer. I've been looking at threads and documentation for four days just to fix the sound issue and so I can be prepared in case this 'feature' ends up being continued in Maverick Meerkat and when I upgrade I can use M.M. with minimal fuss.
View 1 Replies View Relatedi have MB:Gigabyte 770t USB and Cpu Phenom II x2 555 BE My sound card didnt work and i have no sound at alll. only hardware that reconized as sound output in my sound setting is 5700 series HDMI which blong to my VGA.
View 9 Replies View RelatedI am not able to get sound from any Distro on my Desktop (Realtek ALC883) ..Is there any patch to be downloaded for ALSA..Currently i tried Ubunntu 10.04 Live CD ...Request your assistance .
View 6 Replies View RelatedBasically what the title says.I have an ASUS P7P55 WS SUPERCOMPUTER motherboard with the latest BIOS.
View 2 Replies View RelatedI'm using Xubuntu Natty at the moment, on an Acer Aspire 5739G. Figured I would go to Realtek's site and get the most recent soundcard driver, since the built-in subwoofer has never worked on Linux for me.
I used the automatic install script, then when it tried to probe for other devices, suddenly I had no sound.
I'm currently getting
Code:
korin@corrosion:~$ aplay -l
aplay: device_list:240: no soundcards found...
I tried reinstalling the ALSA driver, but to no avail. I now have no sound, and no idea a) why this failed, and b)
I recently installed realtek sound driver software in my system,
but after installing it,the speakers are not working....
I'm using fedora 13(x86_64).
i just want to make my system speak,like before....
how to make my speakers work ?
anyone tried to run wifi-card based on this chip? In coming days I will build myself a proprietary driver for 2.6.27.7 kernel. I mostly aware about patches for wpa_supplicant. Should I use a source for wpa_supplicant from slackware 12.2 distro or a new version? Do you know about any other prerequisities (requirements, dependencies) for building this proprietary driver?
View 2 Replies View RelatedSo I bought a new wireless pci-e adapter today that has a realtek 8192CE chipset. I checked before I bought it and it is supported in the kernel since 2.6.38. Just to be safe I used the kernel-huge-2.6.39-rc4 config file from testing just to get it to work. All the kernel modules are loaded correctly and it is recognized by iwconfig, however wicd acts as if there is no wireless card in the system. I checked dmesg and saw this error.
rtl8192cu:loading firmware file rtlwifi/rtl8192cfw.bin
rtl8192cu:firmware loading failed
So I googled around and didn't find much except for somethings about needing firmware. I did make firmware_install but for some reason there is no rtlwifi/rtl8192cfw.bin file. As a test I found an RPM that had the bin file I needed. I converted it to a tgz and ran explodepkg on it to extract the one file I needed. I made a directory /lib/firmware/rtlwifi and dropped the .bin file in and wicd immediately found my networks. So I guess it is a missing firmware issue, however I am currently not able to obtain and ip address. Why did the kernel not build the firmware I need, or is that something I have to download and build separately?
Well, at first I need to tell that after having big problems (audio, video, modem, network,...) with my venture into slack world at about 7 years ago, I thought that even with my insistence it would be hard to get used with it.
Around the middle of December last year I decided to try again and again I had face some problems (now with fdisk and GPT support in a 64 bit machine).
But now, at about a month after that, I need to say that having passed those initial problems with installation, not only I manage to learn a lot about linux in general (dependencies, rc. editing, permissions, groups...) as I am amazing to what Slackware became.
From 3D graphics acceleration in KDE (with an easy config for my video card, something I thought it would be impossible and that makes it by far better looking than any Windows Desktop fancy try), to great programs and suites integration like Amarok, OpenOffice, Ktorrent, THE firefox, and so many others all allied with the full control of the system (no automatic updates, no mysterious packages UNLESS I really allow it) not to tell g++, python and so on.
However, besides a raid 0 non readable partition, I am having a persistent problem with my wireless that always mix my pppoe connection when I try to config it via rc.inet1 (or rc.wireless ...).To better explain my situation I have a computer with Asus P5k-e/Wifi-AP with came with an integrated wireless device (Realtek RTL8187L).Also, the way I work out to connect to the internet was through (an ethernet) pppoe connection setup using pppoe-setup.Right now it is working like a charm after pppoe-start and stop commands.
At about a month, when i was starting my first steps to config my machine, I tried to follow [URL] three times, and in two of those I manage to start my wireless, but in all it mixed up with my pppoe connection and since either pppoe-config as pppoe-setup didn't work after that (even after backup the files) I had to reinstall the whole system. (Yes, I know that probably there is an workaround easier via shell or file editing, but since every time I need to restart in the Windows, search for solution on internet, print those I find, restart, and try in slackware again, I decided that reinstalling was the fast solution for me at that time.)Now, I am a bit more confident with my knowledge of the linux and decided to try to setup wireless again.
After an extensive search in the forum, I found out two major solutions: One pointing to alienwiki (with I really think is the best approach besides my previous experience) and other pointing to the proper realtek driver at [URL]As i am yet trying to decide which method use, I download the driver and it came with an strange file (RadioPower.sh) that are called by wlan0up. Below are both files:
wlan0up:
Code:
#!/bin/sh
SYSTEM=`uname -r|cut -d. -f1,2`
if [ $SYSTEM = 2.4 ]
then
cd ieee80211
[code].....
I tried to install the latest RealTek driver for Linux and it has wiped all my devices. I've tried reinstalling the alsa-base packages but it hasn't worked
View 4 Replies View RelatedI updated my Slackware installation to 13.37 today. I was running current (a few weeks old).
I recently bought a new set of 2.1 speakers, so i thought of re-running alsaconf and then alsamixer.
Thats when i got this strange error:
Code:
These are the contents of my /etc/modprobe.d/sound.conf
Code:
Here is the output of lspci and dmesg:
lspci:
Code:
dmesg:
Code:
Ok...The funny thing is, the sound still works! (Alsamixer shows all the 6 channels of my previous 5.1 speaker system).
Additional Info:
*Am using a customized kernel - version 2.6.39-rc5.
**It does not work in the default Kernel 2.6.37.6, not even in 2.6.38.
*** It works in kernel version 2.6.35.x and 2.6.36.x. (I checked!)
Not exactly sure but tried several fixes and I'm now getting sound.
Not overly loud but decent enough. Funnily enough it sounds louder inside a windows virtual machine!
I've managed to get everything working including built in webcam on my laptop.The only thing I can't get is sound.
I have a Vaio VPC-EB1E0E which has "Intel HD Audio" . sound worked in Windows when I first booted up and used a Realtek Audio driver.
I'm using Kubuntu 10 RC1 - 64 bit (unable to get any earlier version of U/Kubuntu to work - unable to get Fedora to work either).
The closest info I've seen to helping is:
[URL]
I installed it but wasn't sure how to configure and it still didn't work... (no idea what codec etc)
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05)
Subsystem: Sony Corporation Device 9071
Flags: bus master, fast devsel, latency 0, IRQ 22
[Code].....
an old Compaq Presario 8000, which I reluctantly took, as I tend to end up with more computers than I use and more or less end up acting as a disposal agent. It's a 2.4Ghz machine, which will suffice for whatever I felt like installing on it.I have a generic wifi pci card with a Realtek RTL8185 chipset in it, which I never used and thought I'd set up that computer with it. Hadn't installed Slackware 13 on anything, and it's a distro I like so I went at it.Install went well, no problems there, but I've used Slackware for about 9 years so I'm readily familiar with that end o' things.
I found the rtl8180 module to be causing problems. It would load on boot, but wouldn't bring up a wireless interface. I was able to remove the module with 'rmmod rtl8180' well enough, but when I would load it again with 'modprobe rtl8180', the system would lock. Tried that a few times, same result. I ran across mention of a driver on Realtek's web site, so I downloaded and installed it. That one is identified as 'r8180'. I added 'rtl8180' to the module blacklist to prevent it from being loaded at boot, and proceeded to set up wpa_supplicant.conf for my WPA-PSK connection. Came up without a hitch.The connection is stable thus far, with a respectable link quality. The Realtek driver can be found here.I thought I might document my solution here in case someone else runs across the same issue that I experienced.I'm thinking of slapping another wireless NIC in that computer, or perhaps testing with multihoming possibly. This computer will probably end up as an AP for relaying my wireless traffic to an AP downstairs. I have one USB NIC (Alfa AWUS036S)with a 5dB antenna that has a strong signal, but the ones of more a common variety could use a little help
I was just given a computer from a coworker and installed the latest Slackware version on it. I then installed Gnome Slackbuild and installed the Nvidia driver.I've run alsaconf and it seems to run fine without any errors and unmuted all the channels in alsamixer.
View 6 Replies View Relatedafter update to slackware current 4 days ago i cant get sound working in wine in starcraf 2 i mean i got sound in instalation but not in game and i get error when i wanna configure sound in winecfg
err:alsa:ALSA_CheckSetVolume Could not find '{PCM,Line} Playback Volume' element
err:alsa:ALSA_CheckSetVolume Could not find '{PCM,Line} Playback Volume' element
err:alsa:wine_snd_pcm_recover underrun occurred
err:alsa:wine_snd_pcm_recover underrun occurred
in game i dont got that error but sound dont work btw my sound card is asus xonar essence stx
I'm currently trying to install unRaid on Slackware following this tutorial :[URL].. I'm new to Linux and after many hours, i finally managed to build the new kernel for unRAID (2.6.32.9). But audio on HDMI port doesn't work I tried alsaconf without success. HDMI sound works when i boot into the old kernel.
My codecs are :
Code:
root@unraid:~# cat /proc/asound/Intel/code* | grep Codec
Codec: Realtek ALC888
Codec: Intel G45 DEVIBX
Code:
lspci -v:
[Code]...