Slackware :: Chassis Fan At Max - No Speed Control?
Oct 4, 2010
I got a new computer and got it running Slackware64-current. It's motherboard is an ASUS M4A88TD-M and it's processor is an AMD Phenom II x4 965. I decided to get some chassis fans to improve it's thermal performance. But, since I started the computer after installing the new fan (only one of the 3 I got) the fan's speed is at max and it's very noisy. I'd like Slackware to control it's speed according to temperatures from lm-sensors. Output of # sensors-detect can be found here. Kernel is stock -current 2.6.33.4. Output of # lspci is here.
Code:
gtl@coruscant:~$ sensors
atk0110-acpi-0
Adapter: ACPI interface
Vcore Voltage: +1.31 V (min = +0.85 V, max = +1.60 V)
+3.3 Voltage: +3.34 V (min = +2.97 V, max = +3.63 V)
+5 Voltage: +5.08 V (min = +4.50 V, max = +5.50 V)
+12 Voltage: +12.03 V (min = +10.20 V, max = +13.80 V)
CPU FAN Speed: 2170 RPM (min = 600 RPM)
CHASSIS FAN Speed:3409 RPM (min = 600 RPM)
CPU Temperature: +40.0C (high = +60.0C, crit = +95.0C)
MB Temperature: +32.0C (high = +45.0C, crit = +75.0C)
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +0.0C (high = +70.0C, crit = +99.5C)
How do I go about changing the fan speed? My laptop is running hotter than normal and although its not melting the case I'd rather turn the fan up to increase cooling if possible. Noise is not a concern as I normally have music playing anyway.
I have a Intel Core 2 Duo 1.86Ghz CPU and I have attached a Zalman heatsink & fan to it for extra cooling. However, the default fan speed is very high and it is too loud and definitely unnecessary. So I use this program in Windows called EasyTune5 (which is for gigabyte motherboards, the brand my motherboard is) and I can set the default speed to zero or 1. There are values between 0 and 100, 100 being full speed of the fan. Setting it to a low value like 0 or 1 makes it very quite. Of course the speed of the fan goes up when the CPU heats up or is being utilized more BUT most of the times during idle, its back to being really quite.
Does ubuntu have any software that can do this? I know there are software to check the cpu temp but i need one to actually control the default fan speed.
Is it possible to control the speed of the CPU fan in my desktop computer? The CPU runs cool at 30C yet the fan sits around 2700rpm and the BIOS doesn't allow for speed control.
I have problem with funs speed in my fujitsu rx100 s6 server, rpm funs is 3000 ? I think it is not standard speed funs. On windows 2008 server funs works quietly. Fujitsu supports only windows servers, red-hat enterp. and suse enterp. Is there any software to control speed fans?
I installed Karmic 64-bit on a new Phenom X4 Quad-Core PC. I've replaced the stock CPU cooler with a Cooler Master Hyper TX3, enabled all fan control settings in the BIOS, switched their profiles on silent, enabled the Cool n' Quiet option as well but my CPU fan is still noisy and seem to be running up to the max number of RPM, thus ignoring BIOS specifications. Besides this I can tell there is something wrong with it since even the CPU is on idle or with just the regular browsing, media player operations, PC sometimes freezes or is automatically rebooted .
I installed lm-sensors and went through all the sensors-detect operations (output attached to this post) but it doesn't show anything else but the CPU and HDD temperature which is always 40 Celsius degrees.
Just installed the latest ubuntu on my PC. When I was running windows I had a tool called asus smartdoctor which allowed me to vary my video card fan speed. I really need to increase this fan speed as my video card overheats. Is there a unbuntu compatable program that would allow me to change the fan speed or do I need to install Wine and run smart doctor that way?
I'm trying to control the fan speed on my laptop (IBM Thinkpad T43.) I used lsmod and saw that the thinkpad_acpi module was already load, but I know I need the fan_control=1 option so I did this:
$modprobe thinkpad_acpi fan_control=1. Then I did: $echo level 7 > /proc/acpi/ibm/fan and I get an error: write error: Invalid argument
I'm not sure what I'm doing wrong here, Also, if I wanted to load the module thinkpad_acpi at boot time with the fan_control=1 option, should I add it to /etc/rc.modules? In other words, does the rc.modules file override udev? And do I need to remove the module before reloading it with the fan_control=1 option?
I really need some control over my fan speed, as it seems by laptop is running rather hot.
I have had my thinkpad for just a few short months and, it must be that we are heading into summer, but I am starting to finally run into some overheating issues especially when compiling software for awhile, i.e. kernel.
My question would be, "Is it best to let the built in thermal management take care of the issue, and I just need to know what to tweak, or to put on a script solution such as the tp-fancontrol script?
The computer takes about 5-10 minutes to overheat and the message I get in /var/log/messages is "logger: ACPI group thermal_zone / action THM1 is not defined" then it shuts down.
So, any pointers in the right direction would be appreciated.
I am running slackware-current x86_64 on a Lenovo Thinkpad T500.
I've installed f11 on my machine and am wondering how to control the fan speed for my graphics card, its a asus EAH4850 (single slot, fan starts automatically at around 10% speed).
The card goes at around 85 degrees Celsius with stardard speed with no 3d, and 110+ when running any 3d application, wich then causes it to not respond. i have to set it to around 60% speed for safe temperature.
I'm used to windows, there i could either use the asus smart doctor or the catalyst control center to adjust fan speed, i'm looking for a linux alternative.
I have a Radeon 3870 (rv670) that seems to work great with fc13 out of the box, with one exception. The stock fan is constantly running full speed. It's too loud. Proprietary drivers don't support fc13 yet. Has anyone found a way to make this work?Edit: The best I could do was switch to ubuntu, install fglrx and then issue the following cli commandCode:aticonfig --pplib-cmd "set fanspeed 0 15"
Are there any linux applications that will allow me to adjust the hard drive RPM rotational speeds? I've used similiar programs for windows before but now I am running a linux setup.
how to control the speed of the fan in my laptop ? i use ubuntu ...i don't seem to use it to full power and it is always cool .. it makes lots of noise.i don't know what to say for commands i've run . i tried lm-sensors but it says command not found. sensors gives me some output and "temp1" which say +69degrees maximum 89 ..i used the search function but it just gave me some unsolved threads.
I'm running openSUSE 11.4 with GNOME. I have an EVGA nvidia GTX 285 installed, which is equipped with a variable speed fan. I'm running the nvidia driver package which includes the nvidia X Server Settings utility. The utility allows me to view the fan speed as a percentage of its maximum speed but does not allow adjustment. It appears that the speed remains at the card default of 40% regardless of GPU or card temp. When running certain graphic-intensive applications my card runs quite hot (sometimes >70 degrees C). Although this isn't hot enough to burn the card up in the short term, it is certainly hot enough to shorten my video card's lifespan.
So, the question is how do I set up my system so I can increase the fan speed to 50% or better yet, get it to increase as the GPU temp increases? The nvidia X Server Settings help indicates that fan speed is adjustable after enabling coolbits, but coolbits is not installed on my system and is not available from the default repositories. What is the easiest way to obtain, install and enable coolbits? I have no intention of overclocking my card. It was too expensive to risk damage to the card.
I often run my ubuntu as SSH server only so i stop GDM when i do that, but i found out that after i stop gnome, my ATI gpu fans spins up like crazy and sounds like a jet plane, (i have ati closed source driver installed) i am worried to leave the fan on like that, so i have to start a X session again. Then the fan slows down I would like to be able to have slow fan speed when i drop to text mode only, one is its light weight, two is for security
I am testing a PCI card in a 4-slot bus expansion chassis. I bought the chassis from CoolDrives.com, it appears to be identical to the Startech PEX2PCI4 unit, but was quite a bit cheaper... This device shows up on my lspci output:
I've installed in the expansion chassis one card, a Linux Media Labs BT484 card. This card works out-of-the-box when installed directly in the system, using the bttv driver. Installed in the expansion chassis, the card still shows up as follows:
07:00.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) 07:00.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) 07:01.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
[code]....
When the card is installed directly in the motherboard it gets IRQ17 or 18. I suspect that it does not really want IRQ0, but that there is some problem detecting the proper IRQ over the bus expander. One possible approach I am considering is to build a custom version of the driver where I can set the IRQ manually to something else just to get the driver to finish loading, then see what happens when I run the card. This would at least tell me which IRQ the hardware is really using and whether or not the 0 reported is correct or not.
come across with this issue for one server we are giving support please,help me to know why this issues occurs and alsothat i want a command to display power supplies for the server.please,let me know if anybody is familiar with these kind of issues.
I'm looking at setting up a script that ssh's into our netapp (server01) and then reports an environmental chassis status list-sensors. being relatively new to programming I'm a little lost. I've gotten this far:
I use vsftpd. I would like to know if there is a way to limit the upload speed. Only the upload speed so the "anon_max_rate" and "local_max_rate" don't do the job. Someone told me about the trickle but I expected a more recent application.
I've installed 13.1 and the new GSB. I like it a lot (better than old versions), but the volume applet doesn't work.I did some reading and apparently this is due to a conflict between the GNOME people and the Pulse Audio people. So I was wondering if it was at all possible to use the xfce volume applet.
Newbie slackware user here, I'm having some issues getting keyboard volume control to work properly.I recently fixed my network adapter problem and I managed to get flash player installed despite my minimal knowledge of linux and slackware, but there's yet another small glitch that I can't fix.When I'm logged in as root, keyboard volume controls work perfectly, mute mutes the audio + increases the percentage, - decreases the percentage, etc.However, when I'm logged in as another user and I try to use keyboard volume controls, the bar will pop up in the middle of the screen, but it will be stuck at 0% no matter that I do. (Sound still plays though, it seems that volume is at 100% while the bar in the middle reads 0%).
I started using DWM for my Window Manager really just for the hell of simplicity (I'm an obsessive minimalist) anyways... I can use seamonkey but I do like Firefox more but for some reason it does not load. If from a terminal I type firefox is just simply doesn't load, brings up no errors or anything.
Also, is there a way to control which windows take up what space???
I'm trying to get a Sans Digital raid set up for Slackware.It uses Highpoint Rocketraid control card. I downloaded and built the module for the driver and finally got it to work with an initrd.The raid is set up and mounts to /media/disk1. The drive seems to be working fine.The problem I'm having is I can't get the control software to work. Neither CLI or WebGui. Has anyone made this work with Slackware?
