Just downloaded the Slackware 13.37 ISOs and proceded to begin the installation processHowever, once the setup program gets to the stage where it looks for the CD drive containing the slackware media, no CD drive is found.Looking in /dev doesn't seem to yield any results - no hdx, sdx, or srx devices, apart from my hard drives.When starting, the following kernel messages are printed a number of times:
Code:
ata5: link is slow to respond, please be patient (result=0)
ata5: SRST failed (errno=-16)
I have started to write a SlackBuilds installer, similar in spirit to slackpkg. So far it is only about 100 lines of code and it can search for a package and install it automatically from slackbuilds.org. I doubt it will ever be as polished as slackpkg but it may be useful for some people. Maybe something like this already exists? If it does then I would like to check it out. If however this doesn't exist then I will most likely continue to develop my program. So far it is quite crude but it does install and search for packages.
I have a 16GB flash drive with grub2 installed on it so I can boot Linux iso's in place of burning 200 CD's. I looked at the isolinux.cfg file and came up with this:
However the kernel panics because it cannot mount the root file system. It gives me the options of using my partitions. What should I put for the root parameter?
I am trying to clone my internal drive on my laptop using the dd command after starting up my computer using the 10.10 installer CD. Nothing happens when I follow the instructions from this site: [URL] When I follow these instructions, it doesn't work. I know that I am not being specific here but all I can say is that nothing happens. What am I doing wrong. My internal drive is 250GB and the partition I created on my DOS formatted external drive is 250GB as well.
Just as the title says, where on earth is the source for the setup command during the install? I'm guessing that setup is a script, but I'm not sure (can't find it).
I am installing openSUSE 11.4 on a Dell D620 on which I used to have Ubuntu/XP dual boot. I don't want Windows at all anymore and on the new openSUSE install I just want swap, root, and home partitions.The installation goes fine, but it says my drive is 465 GB not 500, I think what is not showing is my old Windows System partition. I can't see away from within openSUSE to increase the size of my home partition after the install either.With my limited linux skills I think the simplest solution would be to just format the whole drive then install openSUSE. I tried to do that with some XP CDs, but none of them will boot, they keep listing various errors. I tried putting the drive in an external holder to plug it into another computer and format it just using windows, but windows won't recognize it.Using some free live cd/USB I don't know about Using some setting in the openSUSE installation menus I don't know aboutUsing windows or a windows CD (I can post the boot errors if needed)
I am trying to get a new box up. It has XP on one HDD. There is a second HDD, upon which I want to install Ubuntu and dual boot. My problem is that my CD drive is garbage and won't run the installer. Nor do I have any flash drives. Is it possible to install directly from Windows but not "within Windows" persay? If so, how is this done? (I do have Daemon Tools.)
I've been having some problems getting the Ubuntu (9.10 ?) installer to start on my desktop computer. I have created a bootable USB stick using usb-creator (from my laptop), and am able to boot from it on my laptop. However, I get a "Boot error" message on my desktop when I tell BIOS to boot from the USB stick.I'm not sure this is related, but I tried to boot the Ubuntu install CD from my external USB CD Drive, but nothing happened - it just proceeded to boot from my primary hard drive. I have enabled USB boot in the BIOS, but it doesn't list the USB stick as removable media. It lists as a hard disk drive instead. I can't find the external CD Drive on any of those lists.
(Also, the laptop is dual-booting and has grub installed. The desktop has a single OS - WinXP (and hence doesn't have grub installed).. I don't know how this should affect the USB boot though)(I don't think this is a problem with only the Ubuntu installer, but I'd like a confirmation on this)
I'm trying to install DropBox so that the 'DropBox' folder gets placed in /dev/sda4 which is a spare ext4 partition on my disk. Root is /dev/sda1, swap is /dev/sda2 and home is /dev/sda3.
The DropBox installer does not show /dev/sda4 as a location to install it to in the 'Location' drop-down selector.
In Dolphin, the /dev/sda4 partition appears as '19.7 Gib Hard Drive'.
Do I need to do something to make /dev/sda4 accessible to the DropBox installer?
I have this laptop that I just reformatted in hopes of doing a dual boot between XP and FC4. It is an Acer Aspire 5315-2153 (the Wal-Mart special). I reformatted the drive; the Windows partition is in NTFS and then I have a 10GB partition in FAT32 for Linux. When I try to install FC4, the disk boots into the installer, then it tells me that it does not recognize any hard drives (the disk in this laptop is a Hitachi HTS541680J9SA00). It asks me if I want to load any drivers, and I tried a few and still no success. Any way, after it goes through that, it tries to start anaconda and after that launches it goes to a black screen and nothing happens. So, did I do anything wrong in the Windows install that won't allow the disk to be found? The XP disk only allows a format in NTFS, otherwise I would have done FAT32 on the whole drive. Second, is the anaconda problem something related to the HDD issue, or does anyone think that it may be a separate issue?
I'm using the Ubuntu 9.10 alternate install CD in an external PATA USB CD drive to try to install Ubuntu on a ThinkPad X60. The installer boots but then very quickly gets to a stage where it complains that, "No Common CD-ROM drive was detected". It asks you to point out the drive or load or select drivers, but there aren't any drives or drivers to choose. I brought up another console, and looked in /dev, but there isn't anything there that resembles a CD drive.
I tried $ modprobe ide-scsi But it can't find the module.
I followed the instructions here, found the drivers on a working system, and put them on a thumbdrive. However, when I mount it: $ mkdir /tmp/drive $ mount /dev/sdc1 /tmp/drive
Mount fails due to an "invalid argument," with two different USB drives that work just fine on other systems. When even mount doesn't work, I feel like I've got both hands tied behind my back. How I can correctly implement the above command-line fixes? I'm not sure what I'm doing wrong. I've installed different Ubuntus probably a dozen times over the years, and haven't gotten stuck this badly since somewhere around version 4. Whether this problem is specifically related to the fact that my external USB CD drive has a PATA interface. If I go out and buy or borrow a SATA USB CD drive, is this problem likely to go away?
20GB Laptop HDD in external enclosure with USB interface. Formatted FAT32. Shows up in Windows as E:. The Universal USB Installer, however does not see the drive. Is that app only set to look for a true USB flash drive and I'm just doing it wrong?
I've just put together a new machine and as I expected, there are some issues with hardware. I've just tried to set up the installation of ubuntu, got to the partitioning section and only my external hard drive is being picked up. The internal hard drive is a 1TB SATA drive plugged into a 6GB/s DATA port on my m/b (Gigabyte GA-P55A-UD4 running Intel i5 760 processor). I'm probably going to try the alternate CD to see if that works, but does anyone know if this is a common problem for any of my hardware? (I did a google but couldn't find anything).
rescuing my machine after an unfortunate incident with what I assume is a faulty thumbdrive.The other day I bought a used HP 2140 netbook; which had a 1.6GHz single core Atom, 2G mem and a tiny little harddrive. I got it home, put my ssd in it, and within an hour had a nice clean ubuntu netbook edition installed on it. And everything was joy, mostly, for a couple days. But Netbook edition was not as fast as expected, and I wanted to try another distribution. So I put Xubuntu on a new thumbdrive, and tried to install it. Some time during the file copying process, it stalled. I left it on overnight, then turned it off.
I've tried a few distribution iso's; Ubuntu desktop, xubuntu, linux mint. Same thing every time: Installation hangs after clicking next at the screen that checks for specs, space and online status. I can boot from another thumb drive with little trouble, but cannot install from there either. I've tried running GParted, but running it from the meny leads to it crashing. Running it from the terminal still crashes; running it with 'sudo gparted /dev/sda' it runs, and from here I can do most things; I can remove and create partitions, and format to my hearts content. But trying to change flags brings up this error: 'Failed to mount "Uden Navn" The enclosing drive for the volume is locked'. When I close that popup, this comes up in the terminal: 'udevadm settle is not permittet while udev is unconfigured'
I understand that the drive could be locked somehow because of the crash. So I took it out, connected it to another machine, removed the partitions and changed to a guid partition table, and made absolutely certain that the drive had finished ejecting before disconnecting it. Nothing. I tried another harddrive: Nothing I've reset and flashed the bios: Both nothing. I've tried updating GParted; it tells me I have the current version. I've let Xubuntu run thru its updating process from the thumbdrive, and even though it gives me a couple errors underway, it gets thru. But it doesn't help
I used Universal USB Installer to put Ubuntu 11.04 on my flash drive,and then ran it.Why does everything in my Ubuntu become so slow,including surfing the Internet and installing applications?
I created a bootable Debian installer on my USB flash drive. The Debian Installation Guide advises;
The hybrid image on the stick does not occupy all the storage space, so it may be worth considering using the free space to hold firmware files or packages or any other files of your choice. This could be useful if you have only one stick or just want to keep everything you need on one device. Create a second, FAT partition on the stick, mount the partition and copy or unpack the firmware onto it.
I want to put non free firmware packages on the stick but when I try to create a FAT partition in the free space using Disk Utility I get the following error;
Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/sdb, start=661837824, size=7507093504, type= Entering MS-DOS parser (offset=0, size=8168931328) MSDOS_MAGIC found looking at part 0 (offset 0, size 657457152, type 0x00) new part entry
[Code] ....
I formatted the drive to clear it, created a new FAT partition and copied the Debian.iso to it again. When I tried again to create a partition in the free space the same error occurred.
“toshiba satellite u840w with hard disk drive and a solid state disk cache”
Debian 8 installer does not detect the hard drive during installation
I've recently tried to installed Debian 8. The problem is that the partition menu gives me these 3 options: 1. Configure iSCSI volumes 2. Undo changes to partitions 3. Finish partitioning and write changes to disk
There are no options for defining partitions or any hard drive during installation. After searching the internet i found that the problem because the solid state disk SSD cache. How I install a Debian 8 with computer which has a hard disk drive and a solid state disk cache.
more info: I want windows 7(64) and debian dual boot
I'm running into a weird problem when trying to install from the live CD I'm running. Basically, I have two hard drives: sda, a 160GB HDD which has Windows 7 on it, and is the one I would like to put kubuntu on; and sdb, which is a plain 500GB NTFS file system I keep all my personal stuff on.When I get to 'disk setup' and choose 'install side-by-side', it defaults to sdb instead of sda and I can't change it. I've created a 20GB partition on sda, which is where I want to put kubuntu, but it still defaults to sdb. I also can't figure out how to install to where I want using the advanced partitioning menu.
I tried using the Windows installer, after not having success burning the ISO to cd, and I received another error message. "There is no disk in the drive. Please insert a disk into drive. DeviceHarddisk3DR3"
It's not a Slackware-specific question, but I figured someone here might have some insight. Basically what I've got is a 120 GiB drive I was using to boot Slackware. I then mounted a third hard drive inside of my PC (500 GiB) that I wanted to clone the Slackware image onto. But I don't want this drive to be solely used for Slackware so I partitioned off about a 250 GiB chunk for it. Using gddrescue I cloned the image. It booted fine and everything looked good other than Slackware still only seems to think it's got 120 GiB to work with. My question is how can I make it recognize the full 250 GiB, or how can I go a different route to utilize the extra space? Is there some way I can just clone it directly and then go about resizing it afterwards? The first thing I tried was to clone it directly and then attempt to resize it afterwards.However, GParted wouldn't seem to let me resize it so I went this other route of setting up the partitions beforehand.
i downloaded slackware iso (4.3 gigs, i thought it would be smaller) and then when i tried to burn to dvd it give me read sector error when i tried to verify. i tried this with 5 dvd and none worked so something is probably wrong with the iso itself. is there another way to get slackware to install with a usb flash drive or should i just redownload my iso (10 hour download =( ).
I have a dual boot computer with slackware_64 13.1 and windows.
I have a 120G ide hard drive that I need to add to my computer.
Adding this hard drive changes the drive device id's and slackware won't boot.
as installed, my drives look like this:
When I add the extra hard drive, it looks like this:
I know there is a way to make an initrid and to use the uuid identifications for the drives, and even use labels instead of the long uuid's, but I'm unfamiliar with this process, so I was hoping somebody that's done this before might point me in the right direction.
So I have the burned ubuntu CD, and I'm attempting to install it on a system that has one HDD with XP/Vista on it, and another that is completely formatted and unpartitioned. However, when I boot to the ubuntu CD, I can use the menus from the bottom, and select the language when initially prompted, but I can't select any of the menu options except for boot from first hard drive.
I have installed Slackware 9.0 on VirtualBox and I've never used it (slackware) before. How do I access a CD/DVD inserted in my laptop through the KDE?
Ive got an old hard drive with slack on it but I lost the root password. I booted up with the slack install disk but I dont remember how to mount the drive so I can see whats on it. Ive tried to mount it with things like mount /dev/hda and mount /dev/sda and others with no luck.
FYI I'm running Slackware64 13.0 with kde upgraded to 4.3.1.When I run k3bsetup from a shell the gui pops up without the dvd listed in the device section. I know the dvd works since that's what I used to load Slackware with and I can mount cd's and dvd's and copy files from them.In the shell there is a message:QStringList Solid::Backends::Hal::HalManager::findDeviceByDeviceInterface(const Solid:eviceInterface::Type&) error: "org.freedesktop.DBus.Error.Disconnected"
Background: Before this I was using Ubuntu, but I decided to use slackware from now on. So I installed it using a DVD and using the setup program also formatted a USB drive since it asked if I wanted to. After this I could boot into slackware fine (including getting into KDE with startx) and I can shutdown using halt -r now. When I boot with the USB drive in it says "Welcome to the Slackware Linux custom USB boot stick!".
Problem: If I turn on the computer without the USB drive it goes into "grub recovery". I don't know what I should do if I want to boot the computer without the USB drive. I also don't know why GRUB is coming up because I thought it had installed LILO.
