Red Hat / Fedora :: Loading 14 With Nvidia 7300gt - Cannot Enter Anything - System Hangs
Mar 17, 2011
I am having difficulty loading fedora 14 with nvidia 7300gt. I have lots of text on the screen but I cannot enter anything then system hangs there only. The same system runs fine with windows XP The same system runs fine when I use onboard graphic card and disable nvidia. I installed the fedora 14 by disabling nvidia graphic card and used onboard grphic card. I had exactly the same problem with ubuntu, I was not even able to boot from live cd with nvidia. Now I want to use my nvidia graphic card for fedora.
View 9 Replies
ADVERTISEMENT
Mar 31, 2010
Having a problem with my system hanging after updating Fedora 12. Here are my system specs:
Gigabyte MA770-UD3 motherboard
AMD Phenom 9950 Quad Core
6 gig Corsair DDR 800
1 x 160 gig SATA (OS)
1 x 500 gig SATA (data)
I have my system configured for dual boot with Windows 7. After installing F12, I can reboot with no problem. However, after I install the kmod-nvidia drivers, my system hangs on reboot. If I press any key on the keyboard, it will start to load, the freeze until I press a key again. I have tried both Fedora 12 x64 and i386 with the same results. Here are the steps that I took to install the kmod-nvidia drivers code...
Does anyone have any suggestions as to what I am doing wrong?
View 9 Replies
View Related
Feb 6, 2010
I installing Fedora 12. I did ALL the same as in the installation guide, GRUB installed into MBR. And after installation and rebooting - nothing happens, after BIOS messages there is nothing - computer hangs. GRUB seems to be not installedI have 2 hard disks. At first I tried to install on the 2-nd drive(it is slave). Afterward I detach one disk and try with only one hard disk(it is master). Nothing changes - computer hangs.
View 3 Replies
View Related
Jun 19, 2009
I've just installed the new Fedora 11 (just released) through a Live CD having 3 partitions created:
"/boot" - ext3,
"/" - lvm (part 1)
swap - lvm (part 2)
now, I want to add my new Fedora system entry to my "central" lilo.conf, resident on another linux distribution. So, i've done
[Code]...
my lilo fedora entry boots fine but... at the middle of "after boot" loading the system hangs and stops the usual driver detection, etc (normally, it hangs on the CDROM detection or USB 2.0 camera detection).
View 10 Replies
View Related
Aug 26, 2010
My system hangs at boot time when loading hardware drivers for about a minute. It hangs here:
Code: dmesg
[ 8.196035] udevd version 124 started
[ 8.533233] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[code]....
View 9 Replies
View Related
Sep 2, 2010
My system hangs at boot time when loading hardware drivers for about a minute. dmesg
Code:
[ 11.865604] iTCO_vendor_support: vendor-support=0
[ 11.888580] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[code]....
View 3 Replies
View Related
Jun 21, 2011
After I shutdown my laptop while it was updating it's downloaded packages via yum update I faced an error saying " Duplicate packages..." in next yum updateSo I did the following tasks from package-cleanup --dupes # listout duplicatespackage-cleanup --cleandupes # clean up duplicatesIt erased around 600 packagesat was about 6Giafter restarting my fedora hang while loading and completing Fedora Logo..
View 2 Replies
View Related
Apr 25, 2011
i am having old hardware..here the specs..AMD Athlon XP 2200+1.80 Ghz,736 MB of ram,10 GB hard disk and
Nvidia GeForce2 Integrated GPU i tried to use live cd it hangs after loading bar or at some times before itselfi even tried to use fedora 11 kde live but it hangs after booting up
View 9 Replies
View Related
Apr 25, 2011
here are my specs...AMD Athlon xp 2200+,1.80 Ghz,736 mb of ram,10 gb hard disk&Nvidia GeForce2 Integrated GPU...actually it hangs up after loading that bar or sometimes before loading itselfshould i opt for older fedora if so which version i even tried fedora 11 kde but it hangs after booting up
View 1 Replies
View Related
Aug 9, 2010
I just installed Ubuntu Lucid yesterday, and I'm dual-booting with Windows 7. (They're on separate physical drives if that's relevant.) I've discovered that whenever I restart the computer, it doesn't matter if it's from Windows or Ubuntu or just hitting the reset button, it hangs at "Loading Operating System." If I start it cold, though, it usually works fine. I tried Googling but I couldn't seem to find anybody else with this problem. I'm guessing it's a GRUB problem? Does anybody know how to fix it?
View 1 Replies
View Related
Aug 2, 2010
I just joined the forum today. I'm not a linux beginner per se (about 4 years experience, now running Ubuntu Lucid on my laptop and windoze-free) and I built the desktop PC I'm typing this on six years ago. However, this is my first HTPC build and my first KnoppMyth install, and I've probably done something foolish.
This was an attempt at a fresh KnoppMyth 5.5 install on a virgin system. Hardware details:
MB: GIGABYTE|GA-880GMA-UD2H R
CPU: AMD|PH II X4 925 AM3 RT
RAM: 2Gx2|GSKILL F3-10666CL7D-4GBRH
HD: 1T|WD 7K 64M SATAIII WD1002FAEX - OEM
CD: BLU-RAY BURNER LG | WH10LS30 OEM - OEM
[Code]..
Basically, I just wish I had never bothered with KM5.5 and I want a do-over to go back to the beginning and put the LinHES 6.03 CD in and just do the installation. Since I can't do this, I'd like to at least be able to wipe everything I did and start fresh. Recall that I couldn't boot from CDROM even before I made the daft remove of LILO. The only time I successfully booted from CD was the very first time I turned on the machine to install KM5.5
View 1 Replies
View Related
Apr 4, 2011
Adding several 2TB HDDs somehow crashed SATA controller on motherboard.Fedora will no longer boot.
I connected HDD (with Fedora OS) to another computer.Fedora gets past GRUB, but hangs before loading the splash screen.Is something wrong with GRUB settings?Previously, I had dual boot at GRUB (Fedora and WindowsXP).
What is the easiest way to get Fedora to boot properly on another system?I need access to those files.
View 14 Replies
View Related
Mar 19, 2009
I have set this up before (ie installed the drivers and had them working perfectly) but had to do a system wide re-install of fedora. Since this clean install, I've had non-stop grief with nVidia drivers. They have been downloaded and installed via yum, and on start-up nvidia.ko loads. But from with gnome I cant gain access to any 'special effects' (ie desktop effects wont enable).
View 4 Replies
View Related
Jul 27, 2011
I just upgraded from F14 to F15 and have a problem with entering the password for the encrypted FS: when booting with the latest entry in the bootloader:
Quote:
kernel /vmlinuz-2.6.38.6-26.rc1.fc15.i686.PAE ro root=/dev/mapper/vg_anonymous-lv_root rd_LUKS_UUID=luks-3ef72221-1165-46a6-ab69-3932e22e9d4f rd_LVM_LV=vg_anonymous/lv_root rd_LVM_LV=vg_anonymous/lv_swap rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=de
initrd /initramfs-2.6.38.6-26.rc1.fc15.i686.PAE.img
[Code]....
View 1 Replies
View Related
Feb 6, 2009
After a few days of wrestling the xorg.conf file and the akmods/kmod apps, finally have it running properly with a dual display/one graphic card setup BUT only from init 3 and then startx. Trying with init 5 shows a segmentation fault right after recognizing the kmod driver but the sequence keeps running until it after it hits the anacron OK portion. This occurs with an NVIDIA 6800 XT which is covered by the 180.25 driver. Other forum Q&A suggests the wrong driver but NVIDIA recommends this one.
View 3 Replies
View Related
Jan 24, 2010
I finally got the basic 2D working again on my laptop using the updates-testing stuff. But using 3D (glxgears for example) still make my machine to crash. Also, I get weird kernel panics when trying to configure the nvidia:
[code]....
View 8 Replies
View Related
Sep 23, 2010
I have successfully installed the Nvidia driver on my FC13 system that is using an Nvidia NV44 (Ge 6200) card. It seems to be working as I see the nvidia driver when I do a lsmod | grep nvidia and the glxgears program works as well as the nvidia-settings program.Basically, I did the following:
Code:
yum install kmod-nvidia-PAE
new-kernel-pkg --mkinitrd --dracut --update $(rpm -q --queryformat="%{version}-%{release}.%
[code]...
View 6 Replies
View Related
Jan 12, 2011
I am pasting sudo commands without problems as a user (ales in my case) and then immediately the ask the user password.
The keyboard seems to be dead, no keys work, not allowing me to enter the password.
View 6 Replies
View Related
Oct 18, 2009
I'm running fedora 11 2.6.30.8-64.fc11.i686.PAE. System hangs within 10-12 hours of running almost every day. It happens when nobody at the pc. There is nothing interesting in the log files. Kindly let me know where and what I have to check in this case for solving it.
View 12 Replies
View Related
Dec 23, 2009
I booted up the computer (Fedora 11) and it hung at the blue screen with the F bubble in the middle. I waited for quite sometime without any change to the system I held down the power button to power off and tried starting the computer again with the same result.
When the sytem reboots and I press alt+ctrl+2 i see messages like below on the black screen:Unknown username "root" in message bus configuration file.Could not get password database....Failed to start message bus: Could not get UID and GID for username "dbus"..Please help me get the system up. I saved some data and did not take a backup. Is there's a way I can restore my system to a previous date? Or backup my data somehow?
View 2 Replies
View Related
Jun 11, 2010
Problem with FC13 on a 64 bit box...tried to get Tor and Polipo going and at boot, the system hangs as soon as Polipo starts up. I need to adjust or delete the Polipo service but can't seem to get to any kind of a terminal either...it used to be just hit ctl-alt-and and F key and it dropped to a term. Now that's not happening. Can I do that? And...alternatively, can I force a skip of the Polipo service as it's booting?
View 2 Replies
View Related
Nov 20, 2010
I don't know what I did, but for some reason my fedora system hangs on the OS startup when I use my default kernel. I can still use my other kernel to startup the system though, so it's more of an inconvenience really, but any help fixing it would be appreciated.
The default kernel is Fedora (2.6.34.7-61.fc13.i686) when I start up using this kernel the system hangs(I think I using the right term here, but not sure) after these messages code...
View 12 Replies
View Related
Feb 18, 2010
I am running FC12 64bit. Frequently the system hangs usually one app - Thunderbird. If I have Firefox up also, it seems to run fine. The light indicating disk access is on almost constantly. Is there a way to find out what process is accessing which disk? I have 4 hds installed - 2 IDE and 2 SATA. I am having a similar problem trying to do a reboot - it does not reboot within 15 minutes. I need to hit the reset button.
View 14 Replies
View Related
Jul 20, 2010
everything else seems well with my FC13-x86-64 except firefox (3.6.4 and earlier versions too) VERY frequently hangs the whole system. only the mouse still working, keyboard not responding to ctrl-alt-del, ctrl-alt-function or any other key and even num-lock won't turn the led on. system is still remotely accessible through ssh so I can issue a reboot. same thing may have occurred with thunderbird but only once or twice and probably firefox was also running then. no problems so far with google chrome (but I have no flash plugin for that). FC5-x86-32 on my old PC has never had any of these problems.
View 2 Replies
View Related
May 26, 2011
I upgraded F14 to F15 using installation DVD. I have been upgrading since F11 with no problems. Upgrade went well, no issue. After the reboot, the system hangs after the last line systemd.
These are last lines from boot.log:
Starting LSB: start and stop xinetd...
Started LSB: Mount and unmount network filesystems..
Starting Permit User Sessions...
Starting xinetd: Started Permit User Sessions.
Starting Display Manager...
Started Display Manager. [OK]
Started LSB: start and stop xinetd.
Right now I am on system rescue CD, can mount partitions and read logs. I would like to avoid fresh installation if possible.
View 9 Replies
View Related
Jun 3, 2011
As most of us know when you start the machine with the Install Disc in the drive you get a menu that reads:
Welcome To Fedora 15!
Install a new system or upgrade an existing system
Install system with basic video driver
Rescue installed system
Boot from local drive
Memory test
But when you try to boot the install DVD on and EFI based Mac...you only get
Booting Fedora 15 in 3...2...1 ...and then the system hangs.
If any users are having trouble with Fedora Install Media...you can usually use the Install Media from a previous release! In this case, I used the Fedora 14 (64-Bit) disc to install Fedora 15 by simply replacing the 'F14' with a 'F15' in the URLs of the Install and Update repository dialog boxes.
View 2 Replies
View Related
Feb 17, 2010
I have installed Fedora 12 as a workstation successfully, my hardware specification is Pentium 4 system with 2.8 GHz Processor having 512 MB Ram, which has 80 GB HDD, the primary partition where fedora 12 is installed is 20 GB, in primary part my root part is 5 GB, having 2 GB Swap part, also has Home partition which has 12 GB.
The system installed in KDE mode and works nicely, but after 30 or 40 minutes, it is hanged. I don't know why, then I restart the system to resolve it.
View 1 Replies
View Related
Mar 1, 2010
Here's my problem, i have 1 Ubuntu cd, (8.10, free cd), 1x 9.10 32 bit from a friend, and a 64bit 9.10 from a friend. Also i have downloaded 9.10 64bit ISO, (making sure the md5 was correct)This is what ive tried: - Installing inside windows, cd - Installing inside windows, iso mounted - Installing via cd on boot - Installing via usb on boot- Booting from cd/usb, like testing, and install from that (but got to loading screen..)Ive tried the above with all the Ubuntu's mentioned.Yet all have got to the Loading screens and just stopped.With the USB one, once (it had casper on it?), it had errors such as IO, memory buffers etcSo why doesnt either 32 or 64 bit work on my system, is there something i missed?
View 4 Replies
View Related
Mar 29, 2010
trying to install ubuntu on a 2nd partition on a Dell D630. The OS currently on it is Windows 7 Enterprise. I've used Windows 7 to repartition and have 80GB available for the Ubuntu install but when I put the CD in to run it gets detected as a bootable CD and starts to boot but freezes after Loading...I've left it for 2 hrs and it never progressed past that screen. I've also downloaded and burnt the ISO three times (twice in the 64 bit version and once in the 32). In all cases the install never advances. I've also tried a USB install but couldn't get that to boot
View 5 Replies
View Related
Jan 13, 2009
I have a fancy new Quad Core Xeon machine here that I'm trying to install F10 x64 on. The installation went fine. When it reboots the first time, though, I get the dreaded Error Loading OS.
So I dug up my bookmark of the awesome Grub HOWTO here and followed the steps to install Grub manually. Alas, I get the same result after installing it. Even tried doing a makeactive (hd0) just in case, but no luck.
I did more searching and searched for "raid install" but didn't find anything helpful. So here I am... hoping somebody has some insight.
View 1 Replies
View Related
