OpenSUSE Wireless :: Slow Wireless After Upgrade To 11.4?
Mar 20, 2011
I have an Acer Aspire 5920G laptop, which uses Intel PRO/Wireless 3945ABG wireless card. I upgraded from 11.3 to 11.4 using live upgrade and after the upgrade wireless internet became really slow. Now I'm back to 11.3. I experienced the same problem with speed when I was choosing Linux distro - first I tried Fedora and Ubuntu and both had the same problem, but when I tried openSUSE 11.3 it worked fine. With 11.4 Network Manager showed that signal is at 100% and it connected to router with normal speed, but when I tried downloading a file I got 30kB/s max, while I used to get 1,1 MB/s with windows and 11.3. I also noticed that right after boot I got decent speed, but it only lasted for less than a couple of minutes.
Since 11.4 should have better or at least the same driver as 11.3, problem is probably with configuration, but I am using NetworkManager, so I have no idea what could be wrong.
View 5 Replies
ADVERTISEMENT
Aug 12, 2010
I have a Acer Revo R3610 nettop on which I installed oS11.3. It has an Atheros AR5001 wireless network adaptor.I'm getting very bad latency and throughput on with this card. In comparison my Thinkpad with Intel card achieves at least 10 times the throughput from the same location. Also when I boot my wifi will come up authenticate and then a few seconds later disconnect and reconnect. I've tried updating the kernel to 2.6.35 as one of the fixes was to improve the performance of the ath5k driver. I'm using wpa2 authentication.
Here are some details:
Code:
mediacentre:~ # /sbin/lspci -nnk
00:00.0 Host bridge [0600]: nVidia Corporation MCP79 Host Bridge [10de:0a82] (rev b1)
Subsystem: Acer Incorporated [ALI] Device [1025:0222]
[code]....
Is there anything else I paste that will help determine the cause of the bad throughput. Browsing the web or copying files across the network is bordering unusable.
View 9 Replies
View Related
Apr 17, 2010
I haven't done Linux since before it had Wireless support, and have never had to tinker with network settings, so I am at a loss.My searching may be weak, but when I tried, I found nothing relevant except to determine some of the things usually asked for in threads of this nature.The symptom is very slow connection when using wireless, but it does fine when I hardwire it. Using Windows 7 on the same system it flows nicely.
View 4 Replies
View Related
Oct 28, 2010
I have managed to compile and load the RaLink drivers for my wifi card and get an internet connection.My problem is that when I do a broadband speed test on using chrome I get about 1.5 Mbs and on my laptop (Windows 7 meh :-( ) its closer to 7Mbs. I was wondering if there are any other settings I can modify or tweak that could potentially change to improve this. or maybe a better way to test the through put of my connection?I downloaded the latest drivers for my device from Ralink and compiled new module, but I get a little confused on what settings to do and where it reads any configuration information from.
Also this may be off topic or thread, if so I apologise, but I am sure there is a quick answer to this and there is a lot of different information out there on where and how I load my new rt3562sta.ko module into the kernel on start up. As currently I am calling insmod on it manually every time I start up then the Network Manager picks it up and connects.
View 5 Replies
View Related
May 17, 2011
When I had OpenSuSE 11.3 installed originally, I never had any slow internet connection until I erased the hard drive and went to 11.4. This is what my configuration looks like on /usr/sbin/iwconfig:
Cell 01 - Address: AA:AA:BA:BA:AB:BB
Channel:11
Frequency:2.462 GHz (Channel 11)
Quality=70/70 Signal level=-37 dBm
Encryption key: on
ESSID:"housewifiZZZZ" .....
The device I am using is a D-Link DWA-160 which is running the ar9170usb driver (and did on the previous version)
These are the steps I did:
Disable IPv6 from the global tab on Network Settings.
Set DHCP version 4 only in dynamic address in address tab.
Used the anti-IPv6 switches in firefox making these changes
Network.dns.disableIPv6 change from false to true
Network.http.pipelining change from false to true
Network.http.pipelining.maxrequests change from 4 to 8
Added ipv6.disable=1 in DEFAULT_APPEND in Bootloader
(I couldn't find bootloader _APPENDS that was stated in another forum)
Switched from ifup to NetworkManager for Network Setup Method. Reinstalled OpenSuSE 11.4 with Ubuntu 11.04 (to see if it was OS issue) and it still didn't work, so I switched back to OpenSuSE 11.4. Is there anything I did wrong or do I need to do anything additional?
View 2 Replies
View Related
Apr 1, 2010
My first problem is that when I open KNetworkManager the wireless tab is desibled,I don't know why! My laptop is HP pavilion dv6-1245DX. How to get connected to my wireless router?
View 9 Replies
View Related
Dec 2, 2010
No improvement since I first reported this problem, I am hoping somebody can now advise.
Using openSUSE11.3 Linux 2.6.34.7-0.5-default i686 with kde 4.4.4 release 3.Problem is the wait of sometimes over 2 minutes before the wifi connection is available.Two questions:-
1. Why does it take so long? Longer by far than it to be with previous openSUSE releases. Much longer than with that other OS!!!2. How do I remove the wallet process. Not needed in present environment so I would like direct connection without having to open wallet. I didn't set this up, it just happened after I had upgraded to 11.3 and I need to know how to disable it to save time.
View 8 Replies
View Related
Dec 18, 2009
I've got an old Compaq Armada E500 laptop (850mhz PIII, 512mb RAM, 30GB HD) that I've been running OpenSUSE 11.1 w/Gnome desktop. My wireless adapter (Linksys Wireless-G, model WPC54G ver. 2 w/acx-111 chipset) worked well with this setup, but no that I've upgraded to OpenSUSE 11.2 w/KDE, I've got to start all over. I tried doing what I did before, which was to copy the firmware file into /lib/firmware.
View 9 Replies
View Related
Jan 15, 2010
I ran the update last night and my Access Point died!It seems that the update has renamed my wireless interface from wlan0 to ath0.I also noted that the wlan0.mon and wireless.mon interfaces are not there any more? I may not have exactly the right names - 'cos there not there to check! I'll change hostapd.conf (interface=ath0) to reflect the new interface name. what else I must do to get my AP back after the 2.6.27.42 upgrade?
View 9 Replies
View Related
Jan 25, 2009
On my opensuse 11.1 system. I used my tp-link tl-wn321g usb wireless adapter to access the internet. It runs on rt2501 chipset and I used the serial monkey rt73 driver from here.
[URL]
What I did was I installed the kernel-headers, kernel source, gcc and make. And then I cd to the module directory and did
Code:
make
make install
modprobe rt73
[Code].....
I installed "ralink-firmware-1.1-1.5.noarch.rpm" from Software.openSUSE.org. I tried "make" again, but still the same error return.
View 3 Replies
View Related
Dec 1, 2009
I've got an old Compaq Armada laptop (850 mhz PIII processor, 512mb RAM, 30GB HD, DVD ROM) that I've been running OpenSUSE 11.1 on in a dual boot configuration with WinXP for almost a year. I've downloaded and burned a LiveCD of OpenSUSE 11.2 and booted the computer with it. Very impressive. I want to install it on the HD without doing a clean install. That is, I want to replace 11.1 and keep the WinXP partition intact. My biggest trepidation is getting the wireless card configured again. It was a bear the first time. Is there a way to update OpenSUSE without losing those settings?
View 9 Replies
View Related
Jan 7, 2010
This is my first post here. I'm using Opensuse 11.2 (Gnome)and the inbuilt kernel is 2.6.31.xx. My laptop is having bcm4312 (14e4 : 4315 id)chipset for wireless. (0e:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) 0e:00.0 0280: 14e4:4315 (rev 01) ) I have read multiple times here in some threads that this kernel will require Broadcom-wl drivers(Tried ,No success with this) And If I want to use b43 drivers , then I need to go for the 2.6.32 kernel (stable one from this release). I've done the same exactly given in some other link -
Steps-
make mrproper
make menuconfig
make dep
make clean
make bzImage
make modules
make modules_install
After rebooting it's not showing anything new.Just the boot menu with the older one. Experts, Kindly let me know what I'm missing?
View 6 Replies
View Related
Jan 21, 2010
On my opensuse 11.1 system. I used my tp-link tl-wn321g usb wireless adapter to access the internet. It runs on rt2501 chipset and I used the serial monkey rt73 driver from here.
Code: [URL]
What I did was I installed the kernel-headers, kernel source, gcc and make. And then I cd to the module directory and did
Code:
make
make install
modprobe rt73
And then I configured the network with yast.
That was until I upgraded to 11.2 using the guide here.
Code: [URL]
The upgrade went well, but I could no longer use my wireless adapter. I tried installing the driver again but when I tried to run "make", it says
Code:
make: *** /lib/modules/2.6.31.8-0.1-pae/build: No such file or directory. Stop.
rt73.ko failed to build!
make: *** [module] Error 1
I've checked that kernel-headers, kernel-source, gcc and make are all installed.
I installed "ralink-firmware-1.1-1.5.noarch.rpm" from Software.openSUSE.org. I tried "make" again, but still the same error return.
View 9 Replies
View Related
Aug 17, 2011
No wireless after upgrading to linux kernel 3.0 in opensuse 11.4. I'm using Kde and gnome 3, everything was working fine under the 2.6.39 kernel, but now both only detects my wired connection. Any help resolving this would be greatly appreciated. I have a Netgear WNDA3100 adapter that uses the Atheros drivers. It also is no longer detected in my Fedora 15 after upgrading the kernel, but it still works in Mint 11 with the 2.6.38.8 kernel.
View 9 Replies
View Related
Jul 17, 2010
Want to eventually make the switch over but figure taking it slow and learning on an old laptop would be best.
I went through the installer and everything looks great so far except I can't for the life of me seem to be able to get the wireless working. I tried everything a windows newb like me could think of ... it looks like to me the wireless card is not being used since it can't detect anything? I read some threads and here are the results of common terminal stuff that most people say to do:
/sbin/lspci
Code:
00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 03)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 02)
02:01.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T (rev 01)
code....
View 9 Replies
View Related
Feb 7, 2009
I have an intel 5300 wireless chipset which is not supported in kernel 2.6.25. I am currently using opensuse 11.0, I downgraded from 11.1 since I faced so many other problems. can I setup my wireless driver under kernel 2.6.25? if so, how could i do this?
View 7 Replies
View Related
Apr 17, 2010
at start, knetworkmanager detect wireless network, but doesn't automatically connect - I have to restart it to make it work properly. Instead, it gives that error:
[Code]...
View 2 Replies
View Related
Aug 5, 2010
I am getting trouble with knetwork manager. I created a new connection by scanning and connecting using knetwork manager. But every time connection gets disconnected and ask for password and again it connects.
View 8 Replies
View Related
Feb 12, 2011
I have an Atheros AR5007 802.11 b/g WiFi Adapter. I use OpenSuse 11.3, KDE desktop.When I did iwconfig, it displayed the following:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:"sami"
[code]....
View 6 Replies
View Related
Mar 14, 2011
I had the Wireless Broadband working. It stopped working after I closed the laptop (suspend). Also the wifi will not connect until reboot. Now the entry for the Wireless Broadband is gone, and the tab for it is greyed out as well.I would be happy to submit this as a bug and assist with the debugging process.
View 2 Replies
View Related
Mar 29, 2010
I got ubuntu working fine on my netbook and wanted to play around with opensuse. I have it installed and everything works fine except my wireless connection. I have updated everything since the installation through a wired connection, that didn't help. I have read the stickies, but to be honest, I'm so new to this stuff I'm kinda lost. So my wireless network has a WEP encryption and I have entered that password as a 64 HEX Key in the Wireless Manager widget. It connects to the network and says is labeled as active, however there is still the yellow exclamation shield next to the connection. Firefox and other apps don't have access to the internet.
View 9 Replies
View Related
Apr 13, 2010
On Opensuse 11.2, I would like to connect my ipod touch to a wireless ad-hoc network of my laptop. I have no wireless WIFI-router at home, so I have to use the laptop as a router to the internet. I know I have to enter a static IP adres and my router's address, but where ? I haven't found any place under network tools to do this, only saw some fields with SSID's and MAC addresses to fill in.
View 5 Replies
View Related
Aug 17, 2010
i have the cd just do not know how to install the driver for my linksys wireless pci card 14e4:4329the device is BCM43XG
View 4 Replies
View Related
Sep 30, 2010
I've got openSUSE 11.3 running via liveUSB on a netbook and no matter how many times I try, I cannot get wireless to connect to my network.
My network is:
- non-broadcast
- WPA2 Personal
- G
The netbook is fairly recent from Asus and wireless works perfectly with Fedora 11 and Windows XP.
View 5 Replies
View Related
Oct 27, 2010
1 ) make and model of wireless device Athreos 5k
2 ) driver version in use dont know
3 ) any error message. -
abhishek:/ # sudo /usr/sbin/iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Network is down
4 ) what you have tried to rectify the problem.
Tried to install all the patches.
5 ) any trouble-shooting guide you have tried to follow. - The previous two stickies
6 ) openSUSE version 11.3
7 ) type /sbin/lspci -v" in a terminal; copy and paste the section that identifies your wireless card and it's chipset. 07:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Hewlett-Packard Company Device 137a
Flags: bus master, fast devsel, latency 0, IRQ 23
Memory at c2000000 (64-bit, non-prefetchable) [size=64K]
[code]....
View 9 Replies
View Related
Nov 3, 2010
i'm running 11.3 kde 4.4, with a Broadcom 4318. since installing 11.3 a few days ago, whenever i'm connected via wireless, one of two things always happen: when trying to play video (hulu, ....., etc.) in firefox, within a minute or so i will get the BSOD--that is, my screen will go black, and my cap/num lock lights will flash on and off. also, when regularly browsing the internet...not long after opening firefox, it will stop working like i have no connection, and then i will get a frozen screen and system within a minute or two after seeing a variation of this communication message:
"Message from syslogd@sbkra at Nov 2 21:09:53 kernel: [956.784417] process irq/11-b43 (pid: 1974, ti=debee000 task=dd291170 task.ti=debee000 Message from syslogd@sbkra at Nov 2 21:09:53 kernel: [956.784424] Stack: Message from syslog@sbkra at Nov 2 21:09:53 kernel: [956.784458] Call Trace: "a couple times, i've gotten this message and the following freeze when running video in firefox.
strangely, i have no problems running streaming audio through smplayer. and i have no problems playing saved video files through smplayer. and i have absolutely no problems whatsoever browsing or playing online video while connected via ethernet.
i've also searched through the various forum sections to try to address the issue, but nothing i've tried has worked. nor has anyone had a problem identical or even similar to this. btw...in relation to "broadcom", yast tells me that i have "b43-firmware" and "b43-fwcutter" installed. nothing else. i do not have "ndiswrapper" installed, because this gave me problems in 11.2, and this problem mentioned here was happening in 11.3 before i uninstalled "ndiswrapper". and the repos i have are: Packman, OSS, Non-OSS, and Update.
View 9 Replies
View Related
Nov 8, 2010
Sorry for repeating the same old complaint but there doesn't seem to be a common fix: Wireless does not work on my Presario R3000 although SUSE 11.x lists the hardware in the Hardware Information list and the hardware is turned on. Network Manager doesn't display any wireless networks in SUSE while Win 7 can see 4 of them on the same machine. Ubuntu has no problem either
View 1 Replies
View Related
Feb 2, 2011
I have searched and have not found anything specific to my issue. I am currently using NDISWrapper to load the bcmwl15 driver and when it's active it works beautifully.Problem is sometimes at boot, the card doesn't "turn on" and I don't know how else to describe it. The OS does not even detect that the hardware is present. I have disabled wireless hotkey in BIOS. The only way to make the wireless card "active" is to reboot with the wiredconnection to the router. After doing that the wireless card "wakes up" and works awesome.Is there anything I can do to make sure the driver load at boot?mes I get the error that NDISWrapper is not modprobbed when I go to network configuration and if I wish to do i now? I don't know if that has anything to do with the boot sequence. Using the <modprobe ndiswrapper> command as root does nothing permanant
View 9 Replies
View Related
Feb 6, 2011
Just installed 11.3 on a older Dell Dimension 8200 with a D-Link DWA-160 N dual band USB card. The install went ok and the card works (seems a little slow right now but that is next on the list). However, when I run YOU I get the following conflict:
"compat-wireless-kmp-default-2.6.37_k2.6.34.0_12-17.1.i586 requires kernel (default:drivers_usb_core)=6faa2c62dac4f41d, but this requirement cannot be met. Uninstallable providers: kernel-default-base-2.6.34-12.3.i586[openSUSE-11.3 11.3-1.82]"
when the system wants to install patch:Kernel-3038.noarch and patch:Kernel-3709.noarch. I cannot seem to find a suitable provider for the default:drivers_usb_core. Is this something to address here or do I need to go to [URL]?
View 1 Replies
View Related
Feb 17, 2011
I am running openSUSE 11.3 updated with all the latest patches and I cannot connect to my wireless router. I am running Linux Mint 10 on the same type of notebook HP Compaq 6910p and it worked right after the install. If I take off the security WPA & WPA2 Personal I can connect. lspci -v | less shows this for my wireless card.
10:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
Subsystem: Intel Corporation Device 1000
Flags: bus master, fast devsel, latency 0, IRQ 29
Memory at e4000000 (64-bit, non-prefetchable) [size=8K]
[code]....
I am using the same settings for both notebooks just can't figure out why openSUSE 11.3 won't connect. I get the prompt to key in my password, I've even checked the box to show password to make sure I was keying it in correctly. Everything was good but it just goes right back to the password prompt after it fails trying to connect.
View 3 Replies
View Related
