OpenSUSE Hardware :: WSXGA+ - Shows The Desktop With A 1 Inch Wide Black Area Along The Right Border Of The Screen
Jan 18, 2010
openSUSE 11.2 i586, ASUS P3-P5G43 Rev. R1.04G Intel Core2 Duo CPU E8400@3.00GHz, Intel G45/G43 Chipset The Problem: The screen is for the WSXGA+ (1680x1050) standard. This resolution was detected, at the initial install and later with sax2. It shows the desktop with a 1 inch wide black area along the right border of the screen and that is exactly what is missing at the left border (i.e. invisible). It is like the desktop is shifted to the left of the screen. As far as it is visible the image is crisp and clean. Lowering the resolution to 1280x960 works ok, but the aspect ratio is no longer correct. I have checked the archives and found Intel integrated graphics - openSUSE Forums but trying different hints from the thread did not help.
I'm setting up a Dell Inspiron One 2305 and I can't get the native monitor resolution to work without black borders. I'm also experiencing blurry text in Firefox (not sure if this is related). At most other resolutions it will expand to the edges of the monitor fully. Note that the desktop area doesn't extend into the border. I tried glxgears and noticed that it was only pulling 60fps -- figuring it needed drivers I installed the latest ATI drivers. On reboot I was given more options for resolutions however the native one still doesn't work properly. I looked around for troubleshooting tips and looked into xrandr output.
Code:
Screen 0: minimum 320 x 200, current 1680 x 1050, maximum 1920 x 1920 DFP1 connected 1680x1050+0+0 (normal left inverted right x axis y axis) 510mm x 287mm 1920x1080 60.0 + 50.0 30.0 25.0 30.0 1776x1000 50.0 59.9 25.0 30.0
[code]....
Using 'configure display settings' in Gnome, any time I picked a resolution that was 50, it would cause the borders. Any time I picked a resolution that was 60 AND xrandr listed a 60 and 59.9 and said 60 was the selected one, the borders would come back for those too.
So I tried
xrandr --output DFP1 --mode 1920x1080 --rate 59.9
Seeing as every resolution with 59.9 worked. However... This still resulted in borders.
whenever i open my kubuntu desktop it brings a black screen. the pointer of the mouse is active but i cannot see anything.but my gnome desktop works well.what might be wrong?
I have openSUSE 11.3 with an nvidia card connected with two monitors. In the past I used xinerama which was ok, but now I need to have two separate desktops, one on each screen. I set the nvidia driver with x screen, and now one screen works perfect and the other only shows a black screen. When I move the mouse over the black screen, the mouse pointer turns into an X, but moves correctly, which seems to me that the problem is that I need to set the second desktop to that screen. I looked on forums on how to do so, and no luck.
I'm using OpenSUSE 11.2 64 bit. Sometimes boot fails and I get a black screen. It starts quite normal, but when it tries to start X and KDE, it fails and I only see a black screen. I can't switch to terminal and I can not reboot my computer by pressing "Ctrl + Alt + Del". It doesn't even shutdown by pressing the power-button. The only possibility is to switch off the computer. Then it normally starts.
The problem also occures with a clean installation of OpenSuse. And it cannot be solved by updating kernel, X-Server and KDE.
What files do you need? I'll post them.
The same computer worked fine with OpenSUSE 11.1. I think, the new radeon driver could be the problem, I have to use it because I can not use fglrx anymore as with 11.1
I take a look into my log-files, but I cannot see any error. Sometimes it seems, that /var/log/messages is partly overwritten by restarting the machine.
on a 6-7 years old compaq laptop, connected to a brand new hp monitor i am having a mismatch with computer/monitor resolution.
before i had ubuntu 10.04 which could only run in x's safe graphics mode - allowing for full screen resolution but with handicapped graphics - for example videos fullscreen would be quirky and run with cpu at 100%, something which was no problem before 10.04.
then i tried ubuntu 10.10 and later lubuntu 10.10 (which had exactly the same problem); the monitor is running 1440x900 while the computer is rendering to only 1024x768 - leaving a huge black border on right and bottom of screen. the gfx is still crippled; videos fullscreen is quirky as before.
With a default 11.4 (64bit) installation, and the one click installer for VLC at VideoLAN - VLC: Free streaming and multimedia solutions for all OS! - if you get a black screen when watching movie files there are 2 solutions.1)-> Go to Tools->Preferences->Video-> Remove the tick for "Accelerated video output (Overlay)"-> Try and play the movie again, you should now see output.2)Download proprietary drivers for your graphics card - I think theres a thread on the forum dedicated to that.
Example, NVIDIA 8600 using the default 11.4 open source drivers (nouveau?) shows a black screen when VLC uses "Accelerated video output".However, installing the proprietary NVIDIA drivers, VLC will successfully show the movie using "Accelerated video output".To clarify the default VLC installation with "Accelerated video output" ticked - works with proprietary NVIDIA drivers - and doesn't without.
So I updated my software using Yast. One of the updates failed to install. I rebooted and then was in black screen hell with the following information:
Neither the variables MOUSEDEVICE and MOUSETYPE nor the variable GPM_PARAM is set in /etc/sysconfig/mouse Run 'yast mouse' to set up gpm Starting hpssd: Checking/updating CPU microcode unused Starting nfsboot (sm-notify) done done Loading keymap i386/qwert/uk.map.gz done Loading compose table winkeys shiftctrl latin1.add done Start Unicode mode done Starting hotkey-setup done [OK] Starting cupsd done Starting powersaved: ################################### # ACPI system but acpid not running. # # Start acpid first, then restart powersaved! # ############################################### skipped Mount SMB/ CIFS File Systems unused Executing suseRegister (looking for new update channels): skipped Starting SSH daemon done Starting ypbind.....................No domainname set skipped Starting service automounter ("files nis" does not provide any mounts) skipped Starting Firewall Initialization (phase 2 of 2) SuSEfirewallZ: Warning: ip6tables does not support state matching. Extended IPu6 support disabled. SuSEfirewallz: Warning: no interface active done Master Resource Control: runlevel 3 has been reached Skipped services in runlevel 3: nfs gpm microcode powersaved smbfs suseRegister ypbind autofs Welcome to SUSE Linux Enterprise Desktop 10 SP1 (i586) - Kernel 2.6.16.54-0.2.5-default (tty1). linux-bvuz login: Starting ZENworks Management Daemon^[^[^[
I have a laptop Toshiba a65 s-1067 and i just installed ubuntu 10.04 but after updating the files that update manager said i restarted the laptop but now its not booting the gui it just shows a black screen with text going then it apears the logo of ubuntu in dark red backround with some text that i cant read cuz it disapears fast.. after this the screen just goes blan (dark red) and presing ctrl + alt F1 or F8 or anything doesnt work generaly no key works.
I have a laptop which have vista,fedora 12. Today i have install another operating system ubuntu in my laptop. But when i restart it, it not boot up and show black screen. how to resolve this
I prefer ubuntu (which I have been meaning to install for a while) but my netbook currently has linpus lite on it. (It's an acer aspire one). One night I left the netbook sitting open (forgot to close it), and when I went to use it the next day, when I started it up, the desktop did not show the normal icons in the background. It still showed the bar at the bottom with the connection icon, power icon, etc. as well as the "Internet" search bar in the top right corner.
But instead of the usual linpus desktop icons, there are just black and white horizontal bars, with some coloured dots in the black bars. I can still use the terminal to open firefox, and presumably other programs. It still connects to wifi signals, and the bottom bar looks normal and functional. I am posting this message right now with my netbook, and it doesn't seem to have lost any functionality. I would much rather just click on things most of the time instead of opening terminal for everything.
I have a Logitech Quickcam Chat webcam (USB ID 046d:092c) that's worked with my Ubuntu with minimal problems (just some nVidia driver crap) for ages now. I'm not using nVidia anymore (Intel now), but since my fresh install of Lucid, my webcam doesn't seem to capture anything. It is detected by lsusb, but when I open Cheese, the picture is just black. Skype doesn't give me any video at all, not even that annoying static or green lines. Clicking the Test button in my Skype Options undedoesn't do anything;double-clicking it gives me a full-screen grey screen - pressing Escape takes me back to the preferences window. After I get the grey full screen and press Escape, the Test button is gone until I close the Options window and open it up again.Going into gstreamer-properties and testing v4l2 (under Video -> Default Input) just shows me the 'Testing ... Click Ok to finish' window for ages until I close it - no video appears or anything and I'm not entirely sure what I'm supposed to be seeing. Testing with the 'Test Input' option does give me the coloured lines and static. Testing v4l seems to make it crash, but no error comes up in the terminal I'm running it from.lsusb output:
Code: Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 046d:092c Logitech, Inc. QuickCam Chat
I burnt the Ubuntu 9.10 ISO to CD and installed on a freshly nuked Dell 2350. It is pentium 4 at 1.8 MHZ with 512 RAM. Just a spare machine I have sitting there. Install went fine, restarted box, boot from hard drive. I get the little white Ubuntu symbol on a black screen and then a black screen with un-occupied white tool bars at top and bottom of screen and a functional mouse pointer, then nothing. It freezes there.
If I restart by holding the power switch in it occasionally shows multiple CPU overtemp messages and freezes with totally black screen. I can run the CD live and everything works like a champ. I'm going to like Ubuntu once I have this sorted out. If I boot from CD and choose the run from first hard drive option, everything loads and works fine. I was able to remove CD, update and save preferences, etc..
On one occasion, I was able to restart and boot from hard drive and it worked fine but usually it freezes at previously mentioned black screen with white bars top and bottom with mouse pointer. Please excuse my ignorance as I have very little knowledge of the inside workings of computers. I didn't even know about burning ISO's or changing boot orders until reading online. For what it's worth, the computer worked fine with no known hardware problems when it was running XP. It also is completely stock with no mods or added/replaced hardware.
Once I select Ubuntu 9.10 from Grub, it shows the logo, the logo disappears, a jet black screen shows with 2 horizontal white dashes appear at the top.
I recently uninstalled Firefox 3.6 pre using synaptic to go with the stable Firefox 3.6 installed with the PPA repository that was given in the Ubuntu wiki. It installed and ran fine but when I rebooted, ubuntu wouldn't start.
I went into recovery mode a few times, tried to fix any broken packages and when it said it was fixed, I tried rebooting and the same error occurred. I also tried to use dpkg-reconfigure for the xserver-xorg and then ran startx but x didn't load properly. Some more debugging and a few driver errors came up involving intel so I installed a package which fixed that.
Ran the dpkg-reconfigure again and ran startx. This time x loaded but it was a jet black screen and I had to hold ctrl + alt and hit a few F keys to get back to the prompt.
I understand this could be a xulrunner error so I tried reinstalling xulrunner-1.9.1. I also rolled back my repositories to get the Firefox 3.5 branch and I installed the original Firefox 3.5, ran firefox --version to make sure and I finally have that back installed.
I tried rebooting and running the OS normally, but again it failed at the same point. What exactly should I do next? Yes, I could reinstall but it's such a small problem with maybe 1 or 2 broken packages, is there anyway I can save my current ubuntu system (as I have made countless configuration changes months ago and I do not want to do it again)?
SOLVED: Changed the underscan settings in the Catalyst Control Center. I just installed the ATI catalyst driver 10.7, now there is a black border about 1" on all 4 sides that does not want to go away. Below is my xorg.conf
Has anyone seen or heard of the following problem? I have a 1in black border surrounding my display. I've been running google searches all day without much luck. My current setup is as follows: Ubuntu 9.10 (64-bit), 24in asus lcd, Radeon 5770, amd phenom 2 x4, ddr3 4gb, gigabyte mb. I noticed the border while running the live cd. I figured it had something to do with the video drivers. Last night I installed ATI's linux driver 10.2. I'm getting my preferred resolution of 1920x1080 over dvi. But i'm not able to use my full 24in. It's like using a 20in lcd.
I recently upgrade from Lenny to Squeeze. My graphic card is nVidia Corporation G86 [GeForce 8400M GT] (rev a1). Using lenny latest drivers from nvidia worked fine. I installed nvidia drivers using Debian packages 195.36.31-6 and latest driver from nvidia site (260.19.36) and also other nvidia drivers. The problem is when I start gdm3 I saw nvidia logo but then when it loads gdm3 it shows gdm3 screen with lot of black pixels and other random pixels and then the screen freezes. And the only thing I can do is restart using [alt]+[sysrq]+b.
I upgraded from 9.10 to 10.4 and I get the black border around my desktop. I can't find the scaling option and tried installing the proprietary drivers within Ubuntu and still nothing.
If I click the mouse anywhere inside firefox browser window I get a big black strip and it blink on and off. See screen shot.Screenshot-Navigating and Working in Scribus | Linux Journal - Mozilla Firefox.jpg.I can get it to stop by doing a page reload. But it is very annoying. Has this happen to anyone else? If it has has anyone found a fix for this? While I was typing this it happen again.Screenshot.jpg
I just scanned a book recently and as what happens in these situations , the borders get dark I just looking for a simple way (prefer command line) to solve this problem maybe, crop pictures for cutting out the borders and then change the dimension (NOT MEAN STRETCH) to regain original size I am not sure , but any others ways that can turn black border areas to white one is fine with me.
I'm stuck at 800x600, and no matter what i try i seem to hit a dead end. I've got the Intel Mobile 945GM/GMS rev 03, and it seems like lots of people have had to fiddle to get it working. Here's the info I've collected and tried so far. Ubuntu Edgy On Intel 945GM Graphics & Wide Screen LCD NoteBooks � 100% Linux Addict
HOWTO: install drivers and set up widescreen res. with Intel 945 vga card and Ubuntu - Ubuntu Forums Mostly Harmless: SuSE, Acer aspire 5580 and non-standard resolution 1280x800 Intel 945gm And 1280x800 Laptop Monitor Problem Suse 10.2 - openSUSE Forums I'm not too proficient with linux yet, so the right solution might be here and I'm just not getting it right. Maybe i'm not on the right path at all.
15.4 inch laptops tend to be slightly cheaper than 14-inch laptops? Supply and demand? and if you do not mind answering another question, what's your perspective on uncle Larry eating Sun?
I had switched over from Windows to Ubuntu and got rid of windows completely but still had the recovery partition and deleted it. I then tried to add that space to another partition, "Media." For whatever reason it deleted the "Media" partition so I used TestDisk to restore it. I did something wrong and when I rebooted my computer it would not boot so I used my LiveCD to check whats wrong and it had deleted all of my partitions and Ubuntu was nowhere to be found.
So I used TestDisk again to recover them, this time it was successful. The problem now however is that when I start my computer it does not boot into Ubuntu it just shows a black screen with the white underscore ("_") flashing in the corner. I'm not sure but I don't think it is booting into the correct partition, I think it would be trying to boot the first partition, /dev/sda1, rather than /dev/sda3. If this is the problem how could I fix it?
I had switched over from Windows to Ubuntu and got rid of windows completely but still had the recovery partition and deleted it. I then tried to add that space to another partition, "Media." For whatever reason it deleted the "Media" partition so I used TestDisk to restore it. I did something wrong and when I rebooted my computer it would not boot so I used my LiveCD to check whats wrong and it had deleted all of my partitions and Ubuntu was nowhere to be found. So I used TestDisk again to recover them, this time it was successful. when I start my computer it does not boot into Ubuntu it just shows a black screen with the white underscore ("_") flashing in the corner. I'm not sure but I don't think it is booting into the correct partition, I think it would be trying to boot the first partition, /dev/sda1, rather than /dev/sda3. If this is the problem how could I fix it? I got all the boot loader information, here it is:
The computer was working fine last night, when I woke up this morning (I leave it on) it was making strange noises through the speakers and I had a blank screen, restarted a few times had some page full of code and wouldn't move on from there, I went out came back started it up and it did everything normally except instead of a desktop I had a black screen, however strangely enough when I press the power button on the PC a shut down menu comes up, and the mouse works and I can select from the options. I am on an Nvidia ION tho. How do I boot into a safe mode as such? as at the moment I'm using a ubuntu live CD to read the forums!
On the GRUB menu, seclect "Ubuntu (recovery mode)" (not exact wording). You'll get scrolling boot messages until you get to a screen with a grey box and some options. Use the arrow keys to select "x failsafe graphics mode" or something of the like. Press enter and you'll probably get a message that your card can't be detected or something. Press okay and continue. Your screen will be messed up, but you'll be in. It probably isn't the same problem, as you don't have an ATI card and can see a shutdown menu, but good Luck!
How do you bring up the GRUB menu? My PC isnt dual booted so I never see any menus at all, I thought all I had to do was press F8 during boot up? No, F8 is Windows. Hold down shift when booting to see the menu. Downloaded & Installed the 10.6 driver and everything is working fine. Unminimizing apps works much faster with this driver . However, /usr/bin/aticonfig --initial results in
Code: Found fglrx primary device section Using /etc/X11/xorg.conf Saved back-up to /etc/X11/xorg.conf.fglrx-2 /usr/bin/aticonfig: Writing to '/etc/X11/xorg.conf' failed. Bad file descriptor.
Right now I've tried what "jxtreme" suggested on quote nr2 however when I go into recovery mode I get a load of code scrolling through the screen as its supposed to but I never get any box with options as he says, it just gets to a point where there's a small white cursor flashing at me half way down the screen and it stays there...
I have just loaded Ubuntu 10.04 onto a hard drive and then booted using my laptop and it boots all fine and I get to the desktop. After I get to the desktop in around 10-20 seconds the screen suddenly goes black and the mouse disappears and I can't do anything. The fan still goes but thats about it, I have to hard shut down and load up again but it just keeps happening. Not sure what to do next?
Its an old Toshiba Satellite laptop 1.6 ghz processor 1gb RAM
This morning I did some recommended updates for Lucid with update manager. This afternoon at start up I get a black screen after booting. I can hear the sound effect for the login, and if I key in my password, I hear the Ubuntu signature tune, i.e. it is booting and starting up. But my screen is just black with the arrow-shaped pointer, which I can move across the screen with the mouse. Other than that, nothin
I was just about to re-install Ubuntu to dual boot with OS X on my 24 inch aluminium Intel iMac. Then I remembered the reason I got rid of Ubuntu the last time... screen brightness.
It is a known fault of these machines - the default brightness is set far too high. Sometimes it hurts the eyes. There is an application I have to use with OS X called 'shades'.
If I instal Ubuntu in VirtualBox I can still use 'shades', but when I run it natively as a dual-boot os, I do not have access to the 'shades' app so the screen is far too bright to use for any reasonable length of time.
Is there a workaround for this, without having to do something on every log-in?
In ubuntu 10.04 I have compiz installed and when I try to rotate the cube or simply change desktops screen goes black but not entirely, I mean I can still see the cube. This happens only during the change of desktops. Its very annoying,it doesn't create trouble but I cant see the cube effect.
ive just installed Xubuntu Desktop on to my computer, it runs fine, everything loads and so on. but after i log on the bottom 3rd of my screen is completely black
