OpenSUSE Hardware :: Support For Iomega Zip Drives Disabled?
Mar 28, 2010
Have Opensuse disabled support for Iomega external parport zip drives? I can mount the zip drive under Debian Lenny running the 2.6.26 kernel without any problems. Under Opensuse 10.3 (installed) and Opensuse 11.2 (liveCD) I can't access the drive. Opensuse doesn't recognize it.
All of which is odd. When I installed 10.3, the zip was seen an configured in fstab as /dev/sdc4 mounted at /media/zip. It worked fine for a while, then quit. Now, /dev/sdc4 doesn't exist. Kde control center says (hardware - partitions) says is there but not mounted. Hwinfo doesn't show it; modprobe imm does nothing.
I'm at a loss for ways and means to get Opensuse to recognize my zip drive.
View 9 Replies
ADVERTISEMENT
Oct 24, 2010
Recently I noted that when transferring files between my HDs the CPU usage increases up to 80~ 100%. After the transfer ends, the cpu goes back to normal. The system monitor reports no process consuming those cycles, yet there is something eating up The CPU.
Doing some research I concluded it was probably something related to DMA and UDMA. which is weird because all my drives report they have UDMA6 enabled in the BIOS, and in windows I don't have that problem.
Running hdparm -d gives me the following error: /dev/sda3: HDIO_GET_DMA failed: Inappropriate ioctl for device for every partition on every device, though this does not actually tell if DMA is on or off I suspect it is off. I checked if this was a suse exclusive problem, and to my surprise, debian and aptosid, behave exactly the same. The only reason I didnt note before is cause I had never transfered so many files before, (about 250GB) and the small transfers I did were over quite quick.
I'd like to make emphasis on:
1.The problem is the same regardless if I transfer 5GB or 150.
2. In windows my cpu does not go above 10% at any time during the transfer.
I have 3 sata HDs. All my OS's are in sda (120GB) I use sdb (250GB) and sdc (500GB) as data and media storage. ALl drives are Western Digital with less than 2 years of usage, and pass all smart tests with flying colors.
CPu AMD x2 5400 @ 2.8GHz
4GB DDR2 800MHZ
Mother board A780G M2+ SE
View 5 Replies
View Related
Sep 8, 2010
Where can I find a driver for a Prestige Desktop Hard Drive for use on Linux (OpenSUSE 11.3)?
Where should I look, in general, for drivers for this OS?
View 4 Replies
View Related
Jun 4, 2011
I'm running Fedora 15/2.6.38.6-27.fc15.x86_64. When I run <code>qemu</code> I'm getting "Could not initialize KVM, will disable KVM support" I know my CPU supports hardware virtualization, it has the vmx flag (grep vmx /proc/cpuinfo). I've checked that:
1. kvm and kvm_intel modules are loaded
2. /dev/kvm exists.
3. I'm in the kvm group, so I can access /dev/kvm..
Why KVM doesn't work?
View 1 Replies
View Related
Jul 25, 2011
I installed kvm via the package manager but running "qemu" gives the output:
Code:
Could not initialize KVM, will disable KVM support
I'm in the group "kvm" and /dev/kvm exists but seems... empty
I'm not familiar with KVM, QEMU and virtualization technology...
View 2 Replies
View Related
Jul 23, 2009
I was thinking of physically removing the hard drive and use the computer only with a liveCD for security. But is disabling the hard drive in the cmos just as secure, or does software exist that can still access the hard drive?
View 12 Replies
View Related
Mar 17, 2010
I am having following problem. If I try to change my SMB password, it throws following error >
Quote:
~>smbpasswd
Old SMB password:
New SMB password:
Retype new SMB password:
Server did not provide 'target information', required for NTLMv2
rpc_pipe_bind: rpc_send_auth_reply failed.
machine 127.0.0.1 does not support SAMR connections, but LANMAN password changed are disabled
Failed to change password for user1
View 1 Replies
View Related
Jan 18, 2010
I want to use an eSata enclosure which will combine 2 drives into one so I'd be presented with 4TB.
Can 32-bit 9.04 cope with this as one partition or would I have to create multiple partitions on it?
View 4 Replies
View Related
Dec 24, 2010
Last month I found an old Seagate Hornet tape drive (STT20000A) with 2 TR-5 tapes at a thrift store. After sitting on a shelf at my place until last week I put it in an old system and installed Debian 5 on it. After a long time of working on it and never finding any useful help newer than 2007 I'm about to put it on eBay. So, here's a few questions:
Can this work in Debian 5 or should I put 4 or older on the system? If I put older linux on it, could I still get ide-scsi module working? apparently it has be obsolete for some time. The main problem is that it locks up the system when I try to write to it.
View 2 Replies
View Related
Sep 11, 2010
I have an IBM xSeries server with a 120gb IDE hd. I would like to use it for mail and web server at work. Obviously, I need a bigger HD. The only thing is I can't find a big (1TB) IDE HD all I can find are SATAs and this server's motherboard does not support SATA drives.
View 3 Replies
View Related
Jan 15, 2010
As you are probably aware that WD released new drives ranging from 1TB to 2TB with native support for 4K sector size. And as most of stuff written online is regarding Windows and their support for 4K, my question is has anyone already started to use it under linux?
[url]
[url]
I'm thinking about getting one of these drives:
1TB WD10EARS
or
1.5TB WD15EARS
I'm using Debian Lenny so my questions are: is fdisk automatically recognizes that that drive is 4K drive, or it totally ignores it and partition is as 512byte one? In windows if no 4K support is available it would emulate it and performance would be downgraded. Do I need to enable any specific components in kernel so 4K drive is supported? I wanted to make sure there would be no data loss if I select 4K partition type.
View 3 Replies
View Related
Jul 5, 2011
My wife (naturally without consulting me) purchased a WDC "My PassPort" portable usb drive to backup her Windows 7 machine at work. It has an NTFS partition and should be accessable from a Linux box, but she choose to password protect the drive. This apparently requires an executable to run before the drive is unlocked. WDC has provided Windows and Mac versions of their unlock utility, but when I called told they said WDC doesn't support Linux.
It seems odd to me. Are we such a small community that they just don't care? I could remove the password protection and it would probably work with linux. I own a WDC "My Book" external usb/firewire drive that works fine under linux. Just curious why they don't care enough about us to have an linux unlock program. While on the subject I will mention that this drive comes preformated with a virtual CD as one of the partitions. This is a new feature to me. I have not yet attempted to connect via linux to see what happens.
View 5 Replies
View Related
Oct 14, 2010
will going from 10.04 desktop to 10.10 netbook mean i have to reinstall everything? also, does the netbook version support mounting of networked drives?
View 3 Replies
View Related
Jun 23, 2010
We are running CentOS 5 and we are using two identical Iomega USB disks for back-up. We change disk every end of the week. The first Iomega disk was mounted as /media/Iomega, so all cron jobs referred to this mount. However, If we (safely) eject this disk and replace it by the second disk, this disk is mounted as /media/Iomega-1. How can i make that every disk change automatically mounts to /media/Iomega ?
View 1 Replies
View Related
May 1, 2010
I have recently brought a new iomega 1tb hard drive that works fine but there is a small problem.there are three folders that i deleted and when ever i close and reopen the nas drive the folders come back. the folders are called music, videos and pictures.the firmware version is 2.063.does any one else have this problem or know what to do...
View 3 Replies
View Related
Feb 24, 2010
I have an Acer Aspire One running Ubuntu and IOmega External USB Hard Drive 250GB to make up for the 16GB on the netbook. both have been running fine untilRecently I had the Iomega plugged into a Windows XP Laptop which froze, I disconnected the Iomega and switched off the Laptop and rebooted, when I re plugged in the Iomega It failed to display any Items after a little bit of time and one or two shutdowns the Iomega worked fine on the XPHowever when I plug the Iomega into the Netbook it appears under Files and folders but when I open it it just shows me a blank white screen.
View 3 Replies
View Related
Nov 1, 2010
if the Iomega 500gb minimax external usb hard drive is compatible with Linux Ubuntu 10.10, and does anyone have an opinion of the drive. Would I have to reformat it to get it to work with Linux.
Tony044
DELL INSPIRON 6400 LAPTOP
RAM: 1gb
HDD: 1gb
OS: Linux Ubuntu 10.10
View 2 Replies
View Related
Nov 12, 2010
In MS Windows, I had the Iomega Home Storage Manager installed, to manage the hard drive as a administrator. Is there an alternative for Linux, and how to install?
View 2 Replies
View Related
May 29, 2011
iomega prestige 1TB fails to mount on Fedora 15 32 bits. that machine has a USB2 port. /var/log/messages reports this in a loop:
[Code].....
on my Fedora 15 64 bit laptop, it crashes the whole box. (I'll post later the /var/log/messages extract). That machine has a usb 3 port. I'm most interested in making it work under Fedora 15 32 bit, but the crash under 64 bit may give other insight
View 9 Replies
View Related
Feb 28, 2011
I know how to get root access in iConnect and ssh into it. I wanted to know whether we can install any applications on it using the package manager and what package manager it supports, like apt(debian based) or is it based on some other distribution.
View 2 Replies
View Related
Mar 5, 2010
Used gparted to format a brand new iomega prestige 1 tb usb hard drive (ntfs) to ext4. The problem is that I can't create folders from nautilus because I don't have permission (root). There is one folder present already lost + found that appeared after reformatting. i can't access that folder because of permissions. Was any of this supposed to happen after formatting an external drive and how can I fix this? I intend to use grsync to back up important folders but can't create folders from grsync also. The only account on ubuntu is mine and i have access to root privileges.
View 9 Replies
View Related
Oct 5, 2010
I have just installed OpenSuse 11.2 on my IBM G40.
Kernel 2.6.31.14-0.1
Gnome 2.28.2
Model 2388CU2
Memory 744.0
Intel(R) Pentium(R) 4 CPU 2.4
BIOS Version 1TET97ww (1.12)
21.5 GB
In the System Monitor under ThinkPad it says that my fan is disabled.
I will check back later today to see as I do not want to risk overheating my computer right now.
View 3 Replies
View Related
Aug 26, 2010
This is probably already on these forums, but I recently re-installed suse 11.3 and had the desktop effects working fine with the desktop cube animation and everything. But not the case this time...I resume compositing, and try my desktop effect shortcuts, but nothing happens and it comes up saying for me to press Alt+Shift+F12 to resume the compositing again. I do that, but still nothing, and I even re-apply the desktopct settings completely and restart the computer and it comes up saying that none of them were activated or something in the notifications pop-up on the bottom right of the screen. I thought I downloaded the right files (OpenGL??) from the repositories along with basically anything I thought would make it work.
View 3 Replies
View Related
Dec 18, 2010
I am trying to use compiz on OpenSUSE KDE. I launch CCSM, enable some plugins, close it, start it again and all of them are disabled again. I have the compiz package installed.
View 9 Replies
View Related
Feb 14, 2011
I am using openSUSE since last 4 years ,which is installed on my External Transcend 320 Gig External Hard-disk. Now I don't know why but my network is not working, i.e. when I click on "Network Manager", it reads, "Network Manager disabled". So is there any way to overcome from this problem? I also tried to restart the network service but, it did not worked.
View 5 Replies
View Related
Jun 29, 2011
I was having some trouble with dual display on my laptop, so I loaded the system using the nv graphics driver. I got some message from gnome3 saying that my display configuration wasn't supported, and then it fell back to something that looks similar to gnome2. I switched back to the nouveau driver, but gnome3 didn't come back. Does anybody know how to switch it back?
View 4 Replies
View Related
Dec 20, 2009
I am quite experienced in installing openSUSE. (I used it for many years.) But the problem showed below tricks me out.
I just tried to install openSUSE 11.2. In initmode 3 the keyboard works well. Everything worked well up to the moment I started runlevel 5. In XWindows Modus, the keyboard and the mouse are disabled. And I cannot get back to any other Virtual console.
When I started sax2, I get something (in the file /var/log/Sax.log) or both mouse and keyboard like this:
It indicates , mouse and keyboard are disabled.
Here are my questions:
How can I ENABLE my keyboard and my mouse?
Where is the file that configures sax2?
Do I have to set ("on") the AutoAddDevices? or to "off"
View 4 Replies
View Related
Dec 18, 2010
Just bought new laptop i7 with broadcom wireless, intalled opensuse 11.3 x64. I had major trouble to make it work... Even compiled kernel 2.6.37-rc6, but didnt go.Then I took drivers and firmware from git repositories, compiled, did what it was necessary and I made it work.This morning, (since system was new), I just did zypper upgrade (nothing new installed from default installation, I just added packman to repos).And, now wireless is not working. In network manager, option "enable wireless" is disabled.I went to YaST, put network on ifup, it did scan networks, but cant make it work either. Turned it back to network manager, but same thing.Module brcm80211 is loaded, but I cannot make wireless work.
View 4 Replies
View Related
Sep 12, 2010
I installed OpenSUSE 11.3 with disabled WLAN (otherwise the installation process didn't start). Now the system boots only in Safe Mode with enabled WLAN card (when the WLAN card is disabled it also boots in normal mode though). But even if I try to configure the WLAN card in Safe Mode, the system doesn't boot next time (in Safe Mode) until I add "brokenmodules=ssb" parameter. As I understand after reading this forum I should install a firmware/driver, but there is no install_bcm43xx_firmware script in /usr/sbin directory.
[Code]....
View 3 Replies
View Related
Mar 4, 2010
opensuse v11.2, linux 2.6.31.12-0.1-desktop x86_64
ati radeon hd3200 (built into motherboard)
gnome desktop
The video acceleration is clearly not enabled since I can practically watch each pixel drawn. (Well, a bit hyperbolic, but really slow.) Another system, same hardware, had this slow video problem and at one point required a complete OS re-installation. The slow video refresh went away. So there is some way to configure the graphics+display to enable acceleration at install time.
View 4 Replies
View Related
