OpenSUSE :: Compositing Is Temporarily Disabled?

Aug 26, 2010

This is probably already on these forums, but I recently re-installed suse 11.3 and had the desktop effects working fine with the desktop cube animation and everything. But not the case this time...I resume compositing, and try my desktop effect shortcuts, but nothing happens and it comes up saying for me to press Alt+Shift+F12 to resume the compositing again. I do that, but still nothing, and I even re-apply the desktopct settings completely and restart the computer and it comes up saying that none of them were activated or something in the notifications pop-up on the bottom right of the screen. I thought I downloaded the right files (OpenGL??) from the repositories along with basically anything I thought would make it work.

View 3 Replies


ADVERTISEMENT

OpenSUSE Hardware :: How To Enable GLX Compositing

Aug 6, 2010

I have been going crazy for a few days trying to enable compiz on my tc1100. I have a GeForge 420 legacy card and I compiled the proprietary NVIDIA driver. I realize that this is an old card. So perhaps that is why NVIDIA compositing is not enabled by default. If I go to Desktop settings and try to enable 3D effects, it tells me that compositing is not enabled. So I figured I best go with xlg. I installed all that is necessary for compiz-fusion. However, the command glx is not recognised. I also cannot find a package called xlg. Only patterns-openSUSE-xlg. Shouldn t there be a package for xlg? How do I enable compositing??

This is the contents of my xorg.conf
Code:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder63) Tue Jul 13 13:31:50 PDT 2010
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection .....

View 9 Replies View Related

OpenSUSE :: Enable Compositing Support In KDE4.2?

Feb 12, 2009

Configure desktop (Desktop - System Settings) --> Desktop
Message indicates:
Compositing is not supported on your system.
Required X extensions (XComposite and XDamage) are not available.

I can't find XComposite or XDamage as a package to install with Software Management. code...

View 9 Replies View Related

OpenSUSE :: Error: Compositing Is Not Supported On Your System

Dec 1, 2010

I am receiving the following error when trying to enable Compositing in Desktop Settings for KDE4 in openSuse 11.3-Xen

Code:
Error: Compositing is not supported on your system. Required X extensions (XComposite and XDamage) are not available. I want to have desktop effects enabled but can't seem to figure out how to get this done. "Advanced" Tab is greyed out. "Enable desktop effects" is greyed out.

[Code]...

This worked to get X up and running in the Xen kernel. However, I'm pulling what hair I have left trying to figure out how to enable compositing in Xen. The entire motivation for my upgrade was this one feature (amongst some other things).

Please show me where I'm going wrong. I hope this is not a "live with it" type of scenario due to my using Xen.

View 1 Replies View Related

OpenSUSE Hardware :: Unabling Compositing With Nouveau On 11.3?

Jul 16, 2010

Desktop effects are not enabled and in system settings there is the following message "Desktop effects are not available on this system due to the following technical issues: Required X extensions (XComposite and XDamage) are not available."

The nouveau driver is installed. Peering at /etc/X11/xorg.conf I get three pieces of information

- driver ="nv"
- composite ="off"

- threats of war, famine, death and the other one if I edit the file by hand

I tried Xorg -configure and tested the result as it prompts, but that file seemed to contain errors

I can't find anything in YaST to edit the file

- is "nv" correct?

Apart from backing up xorg.conf (which I have) and firing up a text editor to change "off" to "on" does anyone have any more intelligent suggestions?

View 4 Replies View Related

OpenSUSE :: KWin OpenGL Compositing Self-check Failed?

Oct 28, 2010

I have recently updated my ATI drivers to Catalyst 10.10 (ati-driver-installer-10-10-x86.x86_64.run) from the AMD website and I have not been able to get KWin to enable compositing.

I am using:
openSUSE 11.3 x64
KDE 4.5.2

[code]....

View 1 Replies View Related

OpenSUSE Hardware :: 11.4 NVIDIA Drivers And X Compositing - Or XComposite And XDamage

Jul 3, 2011

I've set up a basic 11.4 server/workstation at my home and am having trouble post-nvidia install when it comes to dual-monitors and compositing. Now, I've looked at many posts here and have not found an answer, since most of the answers are obviously for single-monitor setups. The reason I think this is that all the solutions render my second monitor useless (ie, blackscreen/does not function).

Background: I've set up the nvidia 275 drivers via blacklisting neauveau(sorry if I have misspelled) and installing the package [nvidia drivers] from the nvidia website. Everything works great, the login screen comes up on the correct monitor! (I'm quite excited about this, for Ubuntu it took a startup script which, for some reason, rendered full-screen quakelive across two screens instead of one. It was win-lose).

The error I'm getting in the configuration utility for KDE is that compositing is not available because the extensions XComposite and XDamage are not available. These are available and effects work fine if I disable my second monitor. How can I enable for two?

Here's my xorg.conf. I've tried removing this and restarting KDE without and this disables my second monitor, but allows for compositing as mentioned before.

Code:

View 9 Replies View Related

OpenSUSE :: Mc Hangs Temporarily When Network Is Down?

Mar 3, 2011

Midnight Commander startup is usually instantaneous, but when the network (eth0) is down, mct takes over a minute to start.This is a known problem. See:#40 (savannah: MC doesn't open if network gateway inaccessible.) (07 Jan 2007)for example. The problem seems to be caused by mc's use of samba. Is there a known solution or circumvention? The above file advises me to "comment out the eth0 interface from the smb.conf "; however, my /etc/samba/smb.conf seems to have no eth0 interface.The "man mc" file mentions that "smbfs" is one of the virtual file systems used internally by mc. I tried reducing the "vfs" timeout in the ".mc/ini" file from 60 to 5, but this had no effect on the startup time.

View 5 Replies View Related

OpenSUSE Hardware :: Mouse Freezes Temporarily?

Mar 16, 2011

I just installed openSuse 11.4 on my tablet pc HP Pavillion tx 2000 and then I installed Nvidia driver by Yast, adding before the official repository NVidia.Sometimes, it happens that I can move the cursor mouse but when I click nothing happens, while the keyboard works properly. After more some seconds mouse works again.

View 2 Replies View Related

OpenSUSE :: Fix An Unstable 11.2 Desktop / Closes And Freezes Temporarily?

Jun 9, 2010

Is there any way I can install an older version of kde like the on on suselinux 10.1 because the newer desktops are very unstable on my computers. stuff closes, stuff freezes temperarly, fortunetly nothing perminent has happened yet but its been threating to abolish my computer. Ive had other cases like this end up making me reinstall my operating system and Id really like to just fix the problem before it happens. page down is overrun with this horribly lagging scroll.buttons look like there clicking occasionally and again it closes programs and has logged me out once already.

View 9 Replies View Related

OpenSUSE Multimedia :: Mic In Skype Works Temporarily Only - Sound Very Chirpy

Dec 5, 2009

I have quite a strange problem with Skype and Opensuse. First problem was that when I used microphone on Audigy 4 (from some reason recognised as Audigy 2) the sound which people received from me was very chirpy. This problem was solved easily, I just turned my on-board sound system on and started using micorphone from integrated card. And here comes my weird problem. Microphone works all right, but only for short period. After some time after I start talking to someone on Skype the microphone turns itself off, but I can still hear my interlocutors. The only solution is to go to Yast and restart sound system or to restart whole computer, both of which are not real solutions, but well, they sort of work. I'm using Opensuse 11.2 x64.

View 3 Replies View Related

OpenSUSE :: System Freeze Temporarily And Wake Up When Move Mouse Or Press Any Key?

Nov 7, 2010

I have a big problem with my openSUSE 11.2 32bit (but I have experimented the same error with other distributions), this problem consist in a temporarily freeze of my system after some seconds or some minutes if I don't move the mouse or I don't press any key... but when I move the mouse or press any key the system magically wake up and each applications begins to run from the point where was interrupted... this problem also affect on the system clock that loses every second that the system remain frozenMy computer is a notebook with: CPU Intel Core2 Duo T81004GB RAMGPU GeForce 8600M GT

View 2 Replies View Related

OpenSUSE Hardware :: Fan Disabled - IBM G40

Oct 5, 2010

I have just installed OpenSuse 11.2 on my IBM G40.

Kernel 2.6.31.14-0.1
Gnome 2.28.2

Model 2388CU2
Memory 744.0
Intel(R) Pentium(R) 4 CPU 2.4
BIOS Version 1TET97ww (1.12)
21.5 GB

In the System Monitor under ThinkPad it says that my fan is disabled.

I will check back later today to see as I do not want to risk overheating my computer right now.

View 3 Replies View Related

Ubuntu :: Use Compiz On OpenSUSE KDE - Disabled

Dec 18, 2010

I am trying to use compiz on OpenSUSE KDE. I launch CCSM, enable some plugins, close it, start it again and all of them are disabled again. I have the compiz package installed.

View 9 Replies View Related

Networking :: Disabled In OpenSUSE - Enable?

Feb 14, 2011

I am using openSUSE since last 4 years ,which is installed on my External Transcend 320 Gig External Hard-disk. Now I don't know why but my network is not working, i.e. when I click on "Network Manager", it reads, "Network Manager disabled". So is there any way to overcome from this problem? I also tried to restart the network service but, it did not worked.

View 5 Replies View Related

OpenSUSE :: Gnome3 Disabled When Enabling NV Driver

Jun 29, 2011

I was having some trouble with dual display on my laptop, so I loaded the system using the nv graphics driver. I got some message from gnome3 saying that my display configuration wasn't supported, and then it fell back to something that looks similar to gnome2. I switched back to the nouveau driver, but gnome3 didn't come back. Does anybody know how to switch it back?

View 4 Replies View Related

OpenSUSE Hardware :: DMA Disabled On All Hard Drives?

Oct 24, 2010

Recently I noted that when transferring files between my HDs the CPU usage increases up to 80~ 100%. After the transfer ends, the cpu goes back to normal. The system monitor reports no process consuming those cycles, yet there is something eating up The CPU.

Doing some research I concluded it was probably something related to DMA and UDMA. which is weird because all my drives report they have UDMA6 enabled in the BIOS, and in windows I don't have that problem.

Running hdparm -d gives me the following error: /dev/sda3: HDIO_GET_DMA failed: Inappropriate ioctl for device for every partition on every device, though this does not actually tell if DMA is on or off I suspect it is off. I checked if this was a suse exclusive problem, and to my surprise, debian and aptosid, behave exactly the same. The only reason I didnt note before is cause I had never transfered so many files before, (about 250GB) and the small transfers I did were over quite quick.

I'd like to make emphasis on:

1.The problem is the same regardless if I transfer 5GB or 150.
2. In windows my cpu does not go above 10% at any time during the transfer.

I have 3 sata HDs. All my OS's are in sda (120GB) I use sdb (250GB) and sdc (500GB) as data and media storage. ALl drives are Western Digital with less than 2 years of usage, and pass all smart tests with flying colors.

CPu AMD x2 5400 @ 2.8GHz
4GB DDR2 800MHZ
Mother board A780G M2+ SE

View 5 Replies View Related

OpenSUSE Install :: Sax And X11 Disabled Keyboard And Mouse

Dec 20, 2009

I am quite experienced in installing openSUSE. (I used it for many years.) But the problem showed below tricks me out.

I just tried to install openSUSE 11.2. In initmode 3 the keyboard works well. Everything worked well up to the moment I started runlevel 5. In XWindows Modus, the keyboard and the mouse are disabled. And I cannot get back to any other Virtual console.

When I started sax2, I get something (in the file /var/log/Sax.log) or both mouse and keyboard like this:

It indicates , mouse and keyboard are disabled.

Here are my questions:

How can I ENABLE my keyboard and my mouse?

Where is the file that configures sax2?

Do I have to set ("on") the AutoAddDevices? or to "off"

View 4 Replies View Related

OpenSUSE Network :: Wireless Disabled After Update?

Dec 18, 2010

Just bought new laptop i7 with broadcom wireless, intalled opensuse 11.3 x64. I had major trouble to make it work... Even compiled kernel 2.6.37-rc6, but didnt go.Then I took drivers and firmware from git repositories, compiled, did what it was necessary and I made it work.This morning, (since system was new), I just did zypper upgrade (nothing new installed from default installation, I just added packman to repos).And, now wireless is not working. In network manager, option "enable wireless" is disabled.I went to YaST, put network on ifup, it did scan networks, but cant make it work either. Turned it back to network manager, but same thing.Module brcm80211 is loaded, but I cannot make wireless work.

View 4 Replies View Related

OpenSUSE Wireless :: BCM4312 Disabled WLAN On 11.3

Sep 12, 2010

I installed OpenSUSE 11.3 with disabled WLAN (otherwise the installation process didn't start). Now the system boots only in Safe Mode with enabled WLAN card (when the WLAN card is disabled it also boots in normal mode though). But even if I try to configure the WLAN card in Safe Mode, the system doesn't boot next time (in Safe Mode) until I add "brokenmodules=ssb" parameter. As I understand after reading this forum I should install a firmware/driver, but there is no install_bcm43xx_firmware script in /usr/sbin directory.

[Code]....

View 3 Replies View Related

OpenSUSE Hardware :: Video Acceleration Disabled - Enable?

Mar 4, 2010

opensuse v11.2, linux 2.6.31.12-0.1-desktop x86_64
ati radeon hd3200 (built into motherboard)
gnome desktop

The video acceleration is clearly not enabled since I can practically watch each pixel drawn. (Well, a bit hyperbolic, but really slow.) Another system, same hardware, had this slow video problem and at one point required a complete OS re-installation. The slow video refresh went away. So there is some way to configure the graphics+display to enable acceleration at install time.

View 4 Replies View Related

OpenSUSE Hardware :: Support For Iomega Zip Drives Disabled?

Mar 28, 2010

Have Opensuse disabled support for Iomega external parport zip drives? I can mount the zip drive under Debian Lenny running the 2.6.26 kernel without any problems. Under Opensuse 10.3 (installed) and Opensuse 11.2 (liveCD) I can't access the drive. Opensuse doesn't recognize it.

All of which is odd. When I installed 10.3, the zip was seen an configured in fstab as /dev/sdc4 mounted at /media/zip. It worked fine for a while, then quit. Now, /dev/sdc4 doesn't exist. Kde control center says (hardware - partitions) says is there but not mounted. Hwinfo doesn't show it; modprobe imm does nothing.

I'm at a loss for ways and means to get Opensuse to recognize my zip drive.

View 9 Replies View Related

OpenSUSE Wireless :: Card Keeps Disappearing Like Disabled In BIOS

Jul 24, 2010

I'm running SUSE 11.3 on a Dell Inspiron 1501 with a Broadcom BCM4311. I finally got the wireless working earlier with some help from caf4926 and now the card keeps disappearing almost like someone went into the BIOS and disabled it.

View 7 Replies View Related

OpenSUSE Wireless :: Network Management Disabled After Freeze?

Aug 18, 2010

I just switched to opensuse from fedora. So far, I like it a lot (KDE FTW). However, I am having a couple issues concerning hibernation and restarting.Whenever I merely close my computer but don't shut it off, I am forced to reboot. When I open the computer after closing it, everything stays black and nothing seems to work aside from a restart (no good, I know).When I restart, network management is disabled and thus I am prevented from accessing wireless. The only solution I have found is to hibernate, which for some reason fixes the problem. A restart however does nothing. So I guess I have two questions:1) Why can't I close my computer without turning it off?2) Is there a more permanent solution aside from merely hibernating after a crash that will fix network manager

View 7 Replies View Related

Ubuntu :: ATI Compositing Desktop Bug?

May 11, 2010

I am new to linux and ubuntu, but it seems like this bloody bug has not been solved for years. There are many threads as i googled, back from years 2007, 2008... After lucid, i was hoping something (i do not know, if i should have) and googled recently. Found this:[URL].. That xserver thing (which i have tried before for 9.10) does not work!
What am i going to do about this? I cannot even use edge flipping because of that bloody resizing/maximizing problem. I cannot use stuff like docky. No compositing!

Until when should i wait? Is there a possibility of this bug being solved? Should i give my notebook to some windows user and get an nvidia one?

View 9 Replies View Related

Ubuntu :: Compositing Keeps Switching Off?

Nov 26, 2010

I'm running kubuntu, 10.10, 64 bit on my ASUS X59GL, with 4Gb ram - and NVIDIA on board GeForce 8200m.

I'm running KDE with compositing switched on - trouble is that it keeps saying Desktop effects are too slow and compositing is suspended. Surely this setup is powerful enough - this seems to be getting worse with each subsequent release - (a couple of releases ago, this didn't happen).

It's just happened again, and all I'm running is Firefox, nautilus, skype and dropbox (all but firefox are minimised), and uptime load average is .3 Is anyone else experiencing this problem?

Is there any 'ratings' as to how 'expensive' each of the effects are? - i.e. which are the least impact, and which are the most?

View 3 Replies View Related

OpenSUSE :: Total Firefox 3.6.3 / Disabled With Shockwave Flash Plugin?

May 23, 2010

ever since i updated to firefox 3.6.3 on my opensuse 11.0, it has been crashing instantly on loading videos and gmail.

i have done all of the obvious things. run in safe mode, uninstalled and reinstalled including deleting the entire profile, reinstalling the flash player and adobe reader plugins, disabling all extensions (in fact, i have no extensions installed at all now) - nothing works!

i have put a request in to the mozilla forums, but nobody has an answer.

i am able to get firefox to load the videos page only when in safe mode and with the shockwave flash plugin disabled. it still crashes instantly on gmail.

when i go into the yast installer to look for older firefox versions that i might downgrade to, the versions list is in such tiny type that it is unreadable. every other font is fine except that one versions list! it's driving me mad that the one thing i need to see in order to get a working firefox is invisible to me due to some obscure bug.

View 9 Replies View Related

Fedora :: Can't Disable Compositing In Metacity?

May 24, 2010

I was installing cairo-deck and to get rid of the black rectangle i enabled compositing.I got bored of it so I uninstalled it but compositing was still there! I tried to disable it with

Code:
gconftool-2 -s '/apps/metacity/general/compositing_manager' --type bool false
but all i get is
Code:
# gconftool-2 -s '/apps/metacity/general/compositing_manager' --type bool false

Error setting value: Failed to contact configuration server; some possible causes are that you need to enable TCP/IP networking for ORBit, or you have stale NFS locks due to a system crash. See [URL]... (Details - 1: Failed to get connection to session: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken.) I'm using fedora 12 32-bit full upgraded

View 2 Replies View Related

Ubuntu :: Get Rid Of Compiz But Still Retain Compositing

May 23, 2010

Ive been having some really severe problems with compiz on my computer, and Im at a point of utter frustration.

I want to take compiz off of my computer, but I do not want to lose compositing effects, because I run docky (which needs it to run)

Essentially, the problem with compiz, in a nutshell, is that it continually freezes on me when I try to scroll a webpage too fast, or if a fast-paced flash video plays, or anything that might choke up the window manager does. I end up having to pull up a terminal, killall compiz, then restart it manually; it works again until I try to scroll too quickly or something and then it will lock up again.

I know I could run compiz on this computer, but I dont know why this current version will not cooperate, so in lieu of finding a solution, I kinda want to just purge it.

View 4 Replies View Related

Ubuntu :: Just Installed Docky - Need Compositing?

Jan 28, 2011

Docky says it needs compositing to work properly how do I enable this?

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved