Networking :: Named And CNAME Record - Apache Functioning Normally
Jul 23, 2011
I have a question with named and cname records. I wrote a CNAME record into a zone yesterday:
valami.teszt.hu. IN CNAME teszt.hu.
teszt.hu has an A record:
teszt.hu. 14400 IN A val.id.I.P
I restarted named. My problem is: when I visit valami.teszt.hu I get the "Apache is functioning normally" message, and not teszt.hu. And if I write an A record for valami.teszt.hu instead of CNAME record (valami.teszt.hu. 14400 IN A val.id.I.P), the valami.teszt.hu will display
message mentioned above too.
I need to point aaa.com to bbb.com in DNS. I know it is possible to add subdomains for aaa.com to point to bbb.com (or its sub-domains) but in this case I need to have aaa.com point to bbb.com. I used the following in zone file of aaa.com but it didn't work ---------------- @ IN CNAME bbb.com. ----------------
What you should use/? If I create mailserver to point mail.domain.fi should I create for DNS mx record what is actually zone or should just create alias. I prefer to use alias since this is for multiple names for the same domain. What is the right way to do it?
I'm running Ubuntu Server 10.04 to provide DHCP and Internet Sharing on my home LAN. In a previous configuration, I was running Fedora + AMAHI to provide the same services. As most of my linux devices are Ubuntu, I decided to decommission and rebuild my server. I've been able to configure all of my services with the exception of one. As a rule, I assign static IP or reservations based on MAC address's for any of my network devices or appliances.
One cool feature that AMAHI provided a GUI for, was the ability to recognize devices by name as well as IP. i.e.. "http://192.168.1.50" or "http://home-NAS" Going from memory, the long name upon first entry may actually have been "http://home-NAS.adomainname.com"? From my reading, I think I either need to setup up a Static Alias or CNAME for each assigned IP. I can't find any tutorial's that will walk me through this process. I'm guessing I need to generate the records under one of the master DNS zones, but that is just a guess?
There's this domain, that is apparently a cname of a cname which is, I know, not recommended, but it's not forbidden by the rfc. The domain is [URL]. If I try with windows or bind dns I get this results in nslookup:
** server can't find [URL]: NXDOMAIN but if I try with opendns I have some results. > [URL] Server:208.67.222.222 Address:208.67.222.222#53
Non-authoritative answer: www.groenegordel.becanonical name = www.vlaamsbrabant.be. www.vlaamsbrabant.becanonical name = waf.vlaamsbrabant.be. Name:waf.vlaamsbrabant.be Address: 193.53.37.42
With this I see it's a [URL] it's a cname or a cname. Is there a way to force bind to resolve this domain? Is this a limitation of bind?
Mandriva 2009, BIND 9.5.0-P2. Named will start however I'm getting the above error as well as these:
14-Mar-2009 15:45:37.084 general: error: zone 0.in-addr.arpa/IN: loading from master file /var/lib/named/var/named/reverse/named.zero failed: file not found 14-Mar-2009 15:45:37.084 general: error: zone 0.0.127.in-addr.arpa/IN: loading from master file /var/lib/named/var/named/reverse/named.local failed: file not found
[code].....
Named shows to be running but with the errors above I know it's not running correctly. I also copied the above dir's over to /var/lib/named/var/lib/named which is where I 'believe' it's chroot'd at, though I could be wrong since I'm unfamiliar with chroot.
I am using Cent OS 5.5 and i want configure DNS, but while configuring bind i am getting below error.
#/etc/init.d/named restart Stopping named: [ OK ] Starting named: Error in named configuration: /etc/named.conf:57: open: /etc/named.root.hints: file not found[FAILED]
I and setting up a home web server using Ubuntu 10.04 server (local only). I am currently using Webmin 1.53 to access it remotely all is going great very easy to use. Webmin - Check, ftps-fileZilla - Check, Apache -It Works BUT I cant seam to set up Apache as a named server using Bind DSN. Tried most of the help in the fourms and ..... I think my problems is in the master server selection, do i have to use [URL]... or can i just use myservername. I have tryed both with no luck. First time with the server addition.
I am using RackMonkey to map out my lab. Unfortunately, due to RM limitations, every user who accesses the site has write access UNLESS they are logged in as a user named "guest". I currently have Apache allowing only the users (sysadmins) in an LDAP group access to RM, but I would like to allow read-only access for other users as well.I found mod_authn_anon, but I am having trouble combining the two authentication methods. I am using Apache 2.2.18 (compiled myself) on SLES 11.1.
This is the common part:
Code:
AuthType Basic AuthBasicProvider ldap anon Order allow,deny Allow from all
This part by itself works for the LDAP authentication:
Anonymous guest Anonymous_VerifyEmail Off Anonymous_MustGiveEmail Off Anonymous_LogEmail on Require valid-user
But if I have both of the previous blocks enabled at once, then guest access does not work. If I throw in a "Satisfy any", then I am not prompted for a username at all. How can I allow access to this LDAP group and to a user named "guest", but not allow all valid LDAP users to log in?
I installed the netbook remix of 9.10 on a Dell mini10. (Dual boot with XP) I knew that I would have to install the broadcom drivers to get the wireless up and running. What I didn't anticipate is that the eth0 interface would not work. ifconfig shows the device and lists the ip as a 192.xxx number. I am wired directly into our network, and expect an IP in the 10.10.etc range. Pings either return a host unreachable message or say network unreachable. This problem persists even if I set the card to a known good IP. ifdown eth0 returns a message that the interface is not configured. ifup returns a message that it is ignoring the interface.After fighting that problem for a while, I re-installed, thinking that perhaps something had gotten fouled up in the installation process. The problem persists. Nothing has changed.
internet access is no longer working on my computer, ie wget, ping, apt-get update all return unkown host (url or whatever).
However the system monitor (Network History) shows that the system is sending and receiving packets. And what I think is network manager applet shows active network signals for both wireless and ethernet.
I know my laptop has not acquired hardware faults. Since I am posting this message and accessing the internet through the same computer with a Ubuntu live USB start up disk.
I searched through the forums for related posts and tried suggestions. Forinstance
the /etc/resolv.conf
file is the same for both live usb system and hard drive system, so it can not be that.
# Generated by NetworkManager nameserver 79.138.0.180 nameserver 85.8.31.209 the /etc/network interfaces file looks like: code....
I tried the system test (System->Administration->System Test), with only Network tests selected). The results of system test were so extensive I searched for the word internet and extracted lines for internet. Interestingly it says both the network_test and the internet_test are _passed_.
But the internet does not work in either in web browsers or with BASH commands.
And also:
erlang-inets Erlang/OTP Internet clients and servers python-twisted-bin Event-based framework for internet applications python-twisted-core Event-based framework for internet applications network_test pass internet_test pass
I need static networking to be functional on F14 to try freeipa....the problem I have is I am unable to get eth0 to start. Knowing the software it has to be eth0 or it will likely not work... The guest is in a RHEV6svr environment... So I have disabled NetworkManager and enabled networ and set manula settings in ifcfg-eth0 incl the hware address but eth0 wont start on boot....
next I tried setting a e1000 network card after the hypervisor default didnt work, only to find that this doesnt work either. The MAC addresses are changing as I try and fault find a dead DNS client issue (yet another F14 issue but lets not go there yet, it could be RHEV's "funky" NATing setup)....so I suspect F14 has got its knickers in a twist over the MAC for ETH0....I keep changing it and I suspect it cant keep up.....so I need to disable the automatic function(s), if there is one....
So somewhere down in the code there is probably a line saying eth0= <mac address> but despite greping I cant find that.....or not something that I edit and it then works.... I have tried the gui tools and command line tools and I still have no network..... So what would be a totally CLI process to fix this automated crap? ie stop F14 pointing at the wrong MAC for eth0?
I installed 10.04 today, not having used this system for Ubuntu since 8.04. My wireless card (Texas Instruments ACX 111) worked perfectly in Windows XP and 7, and it worked on installation in 8.04.
I did a clean, full install of 10.04 (no dual boot or anything), but the wireless card is not working. The OS doesn't even seem to recognize that it is there because I can't even scan for networks, let alone connect.
The only reason I have a connection on this computer is because I am sharing the internet via ethernet from my Macbook.
I am having some issues and my fixes are not even close to functioning anymore.I originally downloaded this driver http:[url]... and, though I occasionally had to re- "make-install" it, it worked.Last night, I did the system updates Ubuntu suggested and this morning, my WiFi is not functioning .Here are the "common commands" and stuff I have used so far to try to debug the problem.
lspci: 1a/b/g Wireless LAN Controller (rev 20) 0c:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEE iwconfig: wlan0 IEEE 802.11bg ESSID:"***** ******" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff
I am slightly confused as to why my Wireless LAN Controller doesn't come up as my Realtek 8185, but I think that may be issue number 1. The next bit of confusion comes from the fact that wlan0 is shown as connected to the correct SSID, even showing a frequency, but is not, infact, sending or receiving from that source.As I have said before, I just really nee WiFi to work.I was having issues with my sound and graphics cards,so I ran the update manager, but I wasn't expecting it to break my drivers!It is also worth noting that I have actually tried to recompile my drivers and re-install them, they don't seem to be working, for some reason.
I tried using b43-fwcutter in accordance with the Ubuntu Forums and nothing happened, and then I decided to look a little further. According to LinuxWireless.org, the BCM4306/2 actually uses the b43legacy drivers, so I purged all of b43-fwcutter along with firmware-b43-installer and downloaded firmware-b43legacy-installer.
Nothing happened, so I downloaded b43legacy manually per the instructions listed at LinuxWireless.com, and manually extracted from wl_apsta-3.130.20.0.o to my /lib/firmware folder. Nothing happened again. I made sure to check additional drivers and nothing shows up.
As per the ticket posting instructions, I've included all the info you guys could need. from what I can conclude, the wireless isn't even ON, but it's integrated and I have NO IDEA what I have to do to get it up and running.
At least in OpenSuSE 11.3 LXDE I was able to get the wireless on, although I had some major connection issues, I guess it couldn't resolve the handshake completely, or take my SSID/PSK properly.
We have configured DNS Zone like this ..... How to configure CNAME for mk.test.com --> loc2.test.com and per1.test.com --> mk.test.com per2.test.com --> mk.test.com per3.test.com --> mk.test.com per4.test.com --> mk.test.com Need configuring CNAME for mk.test.com,per1.test.com,per2.test.com,per3.test.com and per4.test.com
I was uninstalling some programs through the package manager, then restarted. When my netbook turned back on, I had no internet connection and the WiFi icon wasn't showing in the notification area as it usually does either. Says the card is functioning properly and everything. Other devices can connect to the WiFi.I'm kind of new to Ubuntu and searched around a bit, but am at a loss. HP Mini 110Ubuntu 10.10Broadcom BCM4313Edit: Quote:$ sudo ifconfig -s
I just loaded the Ubuntu maverick AMD64 beta and to my regret I see that the wireless adapter isn't functioning, even after applying updates through wired connection.
Terminal lspci -v command tells me that the network adapter is present as Atheros AR928X Wireless Network Adapter on PCI-E - rev 01 and that the ath9k module is being used by the kernel.
It's possible to configure a second level zone like this: IN CNAME www.domain2.ext For example, if I want: host domain1.ext -> CNAME of www.domain2.ext? and NOT only www.domain1.ext -> CNAME of www.domain2.ext?
I'm trying to create a cname in system-config-bind. I can create the record but when I go to save it I get a "Zone file save error". Here's the full output: Save of Zone file var/named/chroot/var/named/plantsareperfect.com.db failed dns_master_load_/var/named/chroot/var/named/plantsareperfect.com.db:10lantsareperfect.com:cname and other data (sorry, the rest is off the page and I cant see it) Why I can't save this cname?
I am new in configuring named.I want to set my firewall (Fedora 11) as a name server. The local domain is a Windows domain. I'd like internal users translate domain name into IP on this server when they go to the internet. After reading some posts on the web, I set up named as below. It seems the named does the job but with some problems.
1) When I start the server, I couldn't find the named process even if the file "named" is in /etc/init.d. I can browse Internet on the server with domain name (DNS works locally). But internal users couldn't get the domain name translated. If I shutdown the server at this stage, it will shutdown within 1 minute.
2) If I run "service named start" after the server boot up, I see process "named" and named work okay. Both internal user and local host can browse Internet with domain name. However, any command starting with "service named" has no response after this, such as "service named status" or "service named stop". I can see it shows "stopping named" and this last forever. I have to kill the process then restart named server so that named may run again.
3) If I shutdown the server now, it will take 4-5 minute instead of 1 minute in 1). The shutdown stuck at "shutdown named" for 4 minutes. Even if I kill process named before the shutdown, it will take 4-5 minutes.
It took me a week on this issue. I appreciate if you could take a look my configure files and guide me through this.
I'm trying to setup a DNS name server using fedora14. Everything is working in the LAN, I've no errors in log/messages, but cannot ping outside world. Can ping IP addresses but not domain names.
I'm trying to understand dns and I think the following commands should give me an "OK" or something... what am I missing?
Code: # dig @a.root-servers.net . ns >| db.root # named-checkzone . db.root zone ./IN: NS 'K.ROOT-SERVERS.NET' has no address records (A or AAAA) zone ./IN: NS 'L.ROOT-SERVERS.NET' has no address records (A or AAAA) zone ./IN: NS 'M.ROOT-SERVERS.NET' has no address records (A or AAAA) zone ./IN: has 0 SOA records
I'm having some trouble with email being denied because of DNS and/or Reverse DNS issues. I'm hoping someone here is an expert and can shed some light on it for meWe have multiple subdomains, each having it's own entry in the zone file. However, the majority of our traffic goes out an aggregated external IP address with the exception of a few instances such as our mail server and our website(s).We currently have these three records in our example.com zone file:
Code: example.com. IN A 11.22.333.44 www.example.com. 1H IN A 11.22.333.44
i've made a big update of almost 300Mb.I'had a working DNS server.Now, when i boot the box, named works and it resolves all the clients.If i make any change (enter a new client for example) and of course i restart named (service named restart), named stop but does not start again !!!In order to get a working named, i 'm obliged to reboot the box?
I've gotten the Ubuntu Broadcom STA driver working on my AppleTV by (not blacklisting) adding the appropriate rmmod statements to my rc.local script. The system now recognizes the card; lswh -C network:
[Code]....
I can now successfully join wifi networks on the device. My ultimate goal is to create a wifi AP using the card via Ubuntu. The card is a bcm4328. I have attempted to create a wifi hotspot using the "Create new network" menu item from the network menu applet. When I try to join the network on my MacBook, it apparently can join successfully, but then gets a "Self Assigned IP" which is outside the LAN's subnet (which is 192.168.200.X, while the IP on the MBP is 169.254.161.193 and the network control panel indicates that it is self-assigned).
It would appear that the AP on the AppleTV is not bridged with the wifi. I have attempted to follow the CLI-based tutorials but chickened out when I saw I had to set the card to master mode as I do not believe the bcm4328 is capable of this.
I need to record Tx/Rx bw in my c program at defined intervals. I am aware that there a bunch of available tools but I need a minimal version with only Tx/Rx bw with no other details. I have tried the tool bwm-ng which mostly serves my purpose but either it runs continuously in the console or saves result in html file. It does not have any options to save the result in txt file which could have been easy to parse.
Is there any other simple way to record Tx/Rx bw in a program?(without using tools from /proc/net/ or any) I am using Mandriva Linux 2.6.31.5.
