Networking :: Ethernet Controller Missing After Reboot?

Jun 12, 2011

I use Linux Mint Debian XFCE and there was a large update (lots of programs) I have done prior to rebooting. After reboot, my computer can now no longer find the ethernet controller anymore in lspci, so my wired connection no longer works.

Is this a hardware issue? The green lights are all blinking fine though.

View 1 Replies


ADVERTISEMENT

Networking :: Ethernet Intel Gigabit Controller Is Broken Or That Atheros Driver Is Missing?

Apr 21, 2011

I have an ASUS P5Q PRO motherboard with an integrated Atheros AR8121/AR8113 PCI-E Gigabit Ethernet Adapter.I installed Ubuntu 10.04 "Lucid" 64bit Kernel version 2.6.32.21 I have read that the driver isn't in the kernel, but there's a strange thing :

First if I try to run lspci from command line it doesn't reports Atheros Ethernet Controller.

Second If I try to run lshw -C network from command line it doesn't reports Atheros Ethernet Controller.

Third if I run ifconfig it only returns my loopback address.

Can I suppose that my Ethernet Intel Gigabit Controller is broken or that Atheros driver is missing?

View 4 Replies View Related

Ubuntu Networking :: Start The Dc Driver For Ethernet Controller?

Mar 23, 2010

I just installed the latest version of Mint xfce on my old inspiron 8000 with a microsoft MN-120 pci ethernet card, and though the card shows up as hardware, it is not recognized as a network interface. I believe there is no driver loaded for it.

It's an old card, but it seems the kernel still supports it. There are instructions for activating the dc driver that appears to be the proper driver for this chip set, but those instructions originated from freebsd and I'm not sure they translate well. See here:[URL]

I did find a kernel config file, but I was afraid to add the suggested lines to it because there were no other lines specifying "devices". They all started with "config".

View 2 Replies View Related

Networking :: No Eth0, Driver For Ethernet Controller Issue ?

Jul 3, 2011

i am having issues with networking on a certain liveCD.all ubuntu installs ive done on this machine im sure work fine, but i may have had issues with older backtrack versions.My issue is no networking on boot of SamuraiWTF, for those unfamiliar its based on ubuntu 9.04 There is nothing except lo loopback when i run 'ifconfig', and there is nothing in /etc/network/interfaces for eth0 either.

lspci shows a Broadcom driver, but the same command shows the model number etc on a newer ubuntu install on the same machine. This is:

Broadcom NetLink BCM57780

I have the latest .tar.gz of the tg3 drivers suggested by Broadcom, but im lost on how to install them.

-------------------------------------------------------
EDIT: it seems to be an issue with earlier kernels, i installed 2.6.35 and it worked but the kernel isnt mean for 9.04 i dont think, and now theres issues with the nvidia card

View 4 Replies View Related

Ubuntu Networking :: Error Ethernet Controller Is BROADCOM Corporation Device 1692 ( Rev 01)

Dec 1, 2010

I am not able to configure ubuntu 9.04 on network ,

i get error Network UNCLAIMED. error ethernet controller is BROADCOM Corporation Device 1692 ( rev 01)

View 3 Replies View Related

Ubuntu Networking :: Broadcom B44 Ethernet Controller Not Working After Patching Wlan Driver

May 28, 2011

I patched my wireless driver in order to support packet injection. Using this tutorial:

- Install the Firmware:

Code:

- Create new directory:

Code:

- Now disconnect Internet and unload all your driver (use rmmod command)

- Move/copy the Compat-Wireless patched in /usr/src/drivers directory and unpack the drivers:

Code:

Blacklist the wl driver: (STA driver)

Code:

Currently I'm running Ubuntu 10.10, Kernel 2.5.35-29-generic. I have a Broadcom 4318 for my WLAN and a Broadcom 4401-B0 for my ethernet. I followed the tutorial and I managed to get packet injection working on my WLAN; however, my ethernet connection isn't working. I tried sudo modeprobe b44, but I get the following message:

FATAL: Error inserting b44 (/lib/modules/2.6.35-29-generic/kernel/drivers/net/b44.ko): Invalid argument

View 9 Replies View Related

Networking :: Unable To Find Atheros AR8132 PCI-E Ethernet Controller Driver For CentOS / Fix It?

Jun 26, 2011

I am unable to find Atheros AR8132 PCI-E Ethernet Controller driver for CentOS which is installed on my netbook.

I contacted DELL to provide me the driver and they said that they do not support Linux on netbook and I have to arrange it myself.

I told them that I don't need help in installing I just need the driver file to which they said that they don't have driver for Linux.

NIC is getting detected and works fine on the same netbook (Am dual booting Windows7/CentOS) with Windows7

When I type: ls -l /dev/ it does not show up eth0. Same result with ifconfig. When I type lspci | grep net it does show up something like Atheros Communications AR8132 L1 PCI Gigabit .

View 4 Replies View Related

Networking :: Ethernet Interfaces - Device Activated On Reboot

Dec 28, 2010

The ethernet configuration files are under
"/etc/sysconfig/network-scripts" such as "ifcfg-eth0:1" etc.

The file looks as follow:
Code:
DEVICE="eth0:1"
BOOTPROTO="static"
ONBOOT=no
IPADDR="172.23.17.10"
NETMASK="255.255.255.0"
ALIAS="yes"

I've set the ONBOOT=no. This means this device should not be activated at boot-time. But as I reboot the machine, this device is activated again. This means the option ONBOOT doesn't work. Seems this is a bug of RedHat LINUX?

View 3 Replies View Related

Networking :: Fedora 14 - Ethernet Interface Does Not Get Activated Upon Reboot?

Nov 19, 2010

I have installed Fedora 14 about 4 days ago. I have set all the networking parameters like dns path, hostname etc. I have also ensured that I select the check-box for "Enable automatically when system starts" for eth0 interface. But weirdly, whenever I boot my system(or restart), I see that the interface eth0 is disabled. I have to manually enter as root and enable it, each time I boot/reboot my system. Why is this happening? Could you please suggest a way so that I have eth0 interface enabled always when I boot up?Also, my domainname also is not boot-persistent. What steps should I take to ensure that the domainname set once persists across reboots?

View 12 Replies View Related

Ubuntu Networking :: Ethernet Stopped Working After Hard Reboot?

Jun 13, 2010

My computer wouldn't come out of sleep mode, so I had to shut it down improperly. Now there's no ethernet network connection. The NIC works as I can start the computer by wake-on-lan, but somehow Ubuntu no longer sets up a network connection on it.

The green light on the NIC is lit up and blinking. I have changed no settings. It used to get an IP address from the DHCP no problem, but ifconfig now only shows 127.0.0.1.

View 2 Replies View Related

Ubuntu Networking :: 10.04 Kernel Update - No Ethernet Connection On Reboot

Sep 18, 2010

I updated to the latest available kernel for Kubuntu 10.04 today (2.6.32-24). When the system rebooted, it refused to connect to my wireless network. So far I have been unsuccessful in persuading it to connect. ifconfig shows the existence of the ethernet connection as eth0, and Network Manager also seems to accept the existence of the ethernet port - so why has it suddenly chosen now to stop connecting to the wired network?

View 8 Replies View Related

Networking :: Ubuntu 10.04 Realtek Ethernet Driver Missing

May 17, 2011

my Ethernet card stopped responding a few days after installing Ralink Wireless Card Driver for Linux. I have tried installing the drivers from Realtek's site, but it fails. I also have tried reinstalling the network manager, and that still didn't help any. I have also tried looking online for any post or blog that could help, but that also turned up nothing. The Computer is a new 2010 / 2011 (bought it on new years eve) HP Pavilion desktop that came with windows preinstalled.

View 6 Replies View Related

CentOS 5 Hardware :: Intel 82598EB 10G Ethernet Controller

Mar 12, 2010

Does centos 5.4 support this?

product code: E10G41AT2

[url]

View 1 Replies View Related

CentOS 5 Hardware :: Broadcom Ethernet Controller Not Recognized?

Sep 7, 2010

Running CentOS 5

System see the device with an lspci, yet will not load

Vendor:Device ID is 14e4:1691

Broadcom BCM57788 on board ethernet controller

Cannot find driver or anyone that seems to support it. Am I missing something?

This is in a Dell computer.

View 10 Replies View Related

Debian Installation :: Wheezy On Newer Intel I210 Ethernet Controller?

Jul 31, 2013

I just bought a new server with one of the most recent v3 Intel processors (socket LGA1150). The board (Supermicro X10SLM-F) uses the new Intel NICs (i217LM + i210AT), not supported by the current Debian stable release. Hence, the ethernet adapter is not recognized during the installation process.

I would like to be able to install something as close to stable as possible in a production server such as this one.

View 12 Replies View Related

CentOS 5 Hardware :: Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller ?

Mar 31, 2011

I am a newbie who's having trouble installing drivers for Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller.

I already have the drivers from my motherboard vendor, its just that i cant get them to run on my machine. I am running CentOS 5.5.....On the Sytem>Administration>Hardware (Device Manager) I can see the device listed. I am uploading the files for anyone who needs them. I know i need to run an rpmbuild, but i get errors when i try it..... also, i've tried to run atl1.rpm from ElRepo with no luck, i get an error saying Cannot find a valid baseurl for repo:

View 5 Replies View Related

Hardware :: Setting USB Network Controller (SR9600 USB To Fast Ethernet Adapter) On FC10?

Jun 25, 2009

I've an USB Network Controller product from China with no driver for Linux... It's seem in my FC10 not correctky fuctional... On Windows it worked as SR9600 USB To Fast Ethernet Adapter... here is my log...

Code:

[root@home ~]# dmesg | grep USB
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found

[code].....

View 1 Replies View Related

Ubuntu :: Missing Disk Controller On PCI?

Jan 16, 2010

I am attempting to upgrade my system to remove the two aging IDE drives and replace them with four SATA drives. I already have one SATA drive, which means I need a total of 5 SATA ports. My motherboard has two, while I had an existing PCI controller card (Promise TX2-Plus) with two ports. I purchased another card that uses the Sil3112 chip with two ports of its own.I have been running with the one Promise card with no problems for quite some time; lspci output is

Code:
sarmitage@ophelia:~$ lspci
00:00.0 Host bridge: nVidia Corporation nForce2 IGP2 (rev c1)
00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)[code]....

how I can get these two cards working together?

View 1 Replies View Related

Fedora Networking :: Windows Sever 2k3 Domain Controller / Use Machine With Samba As Secondary Domain Controller?

Apr 28, 2009

At the school i work in i have a server2k3 server that provides a domain to all the windows clients, aswell as a fedora server that acts as an imaging machine and webserver.

Im rather concious of the fact that if for any reason the Server2k3 server was to die there is no backup of active directory, or anything that can take its place whilst a replacement is found.

So is it possible to use a fedora machine with samba as a secondary domain controller? so it can be used as a login server, and has a copy of AD.

View 1 Replies View Related

CentOS 5 Hardware :: JMicron JMC250 Ethernet Controller Not Working On Centos 5.5?

Oct 29, 2010

I've installed a new fresh Centos 5.5 ..and after a lot of work..something starts to work (X now works with the new ATI HD5145 using ATI drivers) but i've a serious problemThe ethernet controller JMC250 JMicron PCI EXPR. doesent work at all so my notebook is out of the world !!!Here is some infos:rpm -q centos-release

centos-release-5-5.el5.centos
rpm -qa kernel* | sort
kernel-devel-2.6.18-194.el5

[code]....

View 6 Replies View Related

Ubuntu Networking :: User Interface Changed And It Defaulted To Ethernet And Now It Won't Letting To Go Back On Wireless - Disable Ethernet?

Sep 1, 2011

My laptop was working fine on wireless till the userinterface changed and it defaulted to ethernet and now it won't let me go back on wireless How do i disable ethernet?

View 4 Replies View Related

General :: Ethernet Drivers Are Missing?

Apr 5, 2010

I installed FEDORA 8 on my laptop for a class project. everything went find except. with I attempt to connect to any network. I keep getting the no network device error. so I tried to install the Ethernet and wi-fi driver directly without success.

View 1 Replies View Related

OpenSUSE Network :: Ethernet Card Missing After Upgrade?

Jul 1, 2011

I have a strange problem. An old PC is my home server. On the PC I had in the long past 2 NICs. For the last year or so, I had only one NIC installed, a Compex with 8139too module which run just fine. After the upgrade to 11.4, 32bit of course, with zypper dup, I saw that I had no internet and no network connection to the server. So, I logged on the server and found that rcnetwork could not start the eth0 and eth3(!). OK, a mistake I thought. Enter Yast and solve it. Unfortunately, yast reports 2 cards! I removed all of them, rebooted but nothing. lspci reports 2 cards, while I have NONE installed on the motherboard!hwinfo --netcard the same! yast the same! So, the OS "knows" that I have 2 NICs, while I definitely have none!

Checked if /etc/udev/rules.d/70- had any left data from the past, but the file was empty. Checked the /etc/sysconfig/network/scripts nothing again.In principle, the openSUSE 11.4 believes that I have 2 cards (and with wrong MACs, obviously) and I cannot make it rescan the PCI bus to find that I have nothing! I am sure that some garbages are left somewhere but I don't know where to look at. it is very critical to have that server but on-line and in my LAN.

View 9 Replies View Related

CentOS 5 :: Eucalyptus Node Controller And Cloud Controller Apps Won't Bind To IP

Jun 18, 2010

I can not get the node or cloud controllers to startup using the init.d scripts. I have a fresh install of CentOS 5.4 with Eucalyptus 1.6.2 I have compiled Eucalyptus and all packages using the RPM supplied from Eucalyptus and utilizing yum installer. I do not currently have any processes or applications listening currently on the ports on the boxes as well. I think it may be a permissions issue or something because I get a "permission denied error", but I am not sure if it is Eucalyptus or CentOS. It looks as if it is not binding to the address on the interface of the NIC. It may be something else however. I have the Node controller, Cloud controller, and Cluster controller on seperate physical boxes. When I try to run either the cloud controller or the node controller I get this message:

Cloud Controller:

[root@cluster-cont ~]# /etc/init.d/eucalyptus-cc start
Starting Eucalyptus cluster controller: (13)Permission denied: make_sock: could not bind to address [::]:8774
(13)Permission denied: make_sock: could not bind to address 0.0.0.0:8774

[code]...

View 2 Replies View Related

Ubuntu :: Clipboard Missing After Reboot (KDE)

Aug 15, 2010

Now this is a bit odd but I have seen it happen before: after rebooting the clipboard icon is missing from the system tray. I am using KDE 4.* and karmic on the relevant machine. Any simple way to get it back without rebooting?

View 2 Replies View Related

Ubuntu :: Proper Analog Controller With Joypad/controller Mupen64plus?

Sep 15, 2010

Basically i want it so that the analogue stick on my PS2 controller, which connects via a USB adaptor and is recognized, correctly controls in game characters. It seems to work fine enough in platformers, at least it does with Banjo Kazooie, but with games like perfect Dark it seem to be trying to move forward and look down at the same time, also backward and look up simultaneously and look sideways and move sideways simultaneously , rendering the game all but unplayable.

I have tried running jscal and, apart from the fact that it seems a bit beyond me, it reports "jscal: missing devicename" when i try to run "jscal -c". Do others out there have there analogue sticks working correctly with games like Perfect Dark, or the James Bond games, for example?

View 4 Replies View Related

Debian Configuration :: Ethernet Card Missing/Compile Latest Kernel?

Dec 17, 2010

This may sound ridiculous, but after installing Debian 5 (from CD 1) in my laptop, ASUS UL80VT, it fails to detect the Ethernet device. The device is "Atheros AR8131 PCI-E Ethernet Controller". I guess the problem comes with the old kernel of version 5. I was intending to compile the latest kernel anyway. But the problem is is there any heads up i need to download the kernel and trying to compile it? Is there anyone who uses Debian on UL80VT. If there is, does it works okay?In short I want to compile the latest kernel, hoping it will fix the Ethernet device. There are installers available with the latest kernel. But I want to do it on my own.

View 4 Replies View Related

General :: Missing Eth0 Ethernet Interface In Ubuntu — Can't Connect To Router

Aug 27, 2011

I'm having trouble getting my Ubuntu 10.04 machine (Sony Vaio VGN-SR490) to connect to the Internet by way of an Ethernet cable connected directly to my router.

I'm able to connect to the Internet using this same cable using a Windows machine, so there's something wrong with the way Linux is configured.

How do I got about figuring out what the problem is and solving it?

Here are my network settings on Linux:

$ ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host

[Code].....

It looks like the network adapters list is empty. I will now install both Windows XP and Ubuntu Linux dual-boot. I'm still not able to access the internet, even through Windows. I'm wonder if this could be a hardware problem with the computer or a problem with the router itself. Other computers can connect to this same router, and work fine. (That's how I'm posting this after all!)

View 3 Replies View Related

Ubuntu :: Always Missing Gnome Panel After Reboot?

Dec 10, 2010

i have some problem with my Maverick, his gnome panel (top panel) always missing after reboot, and I always type gnome-panel & to get back my gnome panel, get back my panel permanently?

View 1 Replies View Related

Ubuntu :: Installed Programs Missing After Reboot?

Jun 27, 2011

i has follow website article to create a Ubuntu 11.04 on a 4GB flash drive. And, i has use "EASEUS Partition Master Home Edition" create 2 partition on my USB flash drive (2GB MBR with ubuntu 11.04, 2GB data volume). I has able to run my Ubuntu11.04 from USB and i was so happy and then start installed VLC player, Ubuntu Tweak, unrar programs. after those programs installed, i reboot the Ubuntu then i encounter all installed programs were missing,,,,the O/S back to it's original state. How am i can installed programs in USB flash drive and keep it on USB flash drive.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved