Running CentOS 5
System see the device with an lspci, yet will not load
Vendor:Device ID is 14e4:1691
Broadcom BCM57788 on board ethernet controller
Cannot find driver or anyone that seems to support it. Am I missing something?
This is in a Dell computer.
I've been trying for probably 10 hours now to get the bcm4306 driver working on Debian. I finally got it installed using ndiswrapper... However, now ndiswrapper says that the hardware is not present! When I run lspci, though, it lists BCM4306 as the network controller. What is going on, and how do I fix it? It's on a Dell latitude D600.
View 3 Replies View RelatedI am not able to configure ubuntu 9.04 on network ,
i get error Network UNCLAIMED. error ethernet controller is BROADCOM Corporation Device 1692 ( rev 01)
I patched my wireless driver in order to support packet injection. Using this tutorial:
- Install the Firmware:
Code:
- Create new directory:
Code:
- Now disconnect Internet and unload all your driver (use rmmod command)
- Move/copy the Compat-Wireless patched in /usr/src/drivers directory and unpack the drivers:
Code:
Blacklist the wl driver: (STA driver)
Code:
Currently I'm running Ubuntu 10.10, Kernel 2.5.35-29-generic. I have a Broadcom 4318 for my WLAN and a Broadcom 4401-B0 for my ethernet. I followed the tutorial and I managed to get packet injection working on my WLAN; however, my ethernet connection isn't working. I tried sudo modeprobe b44, but I get the following message:
FATAL: Error inserting b44 (/lib/modules/2.6.35-29-generic/kernel/drivers/net/b44.ko): Invalid argument
I have just installed a NEC 3.0 PCIe board in my CentOs 5 box, but the card is not recognised, and no drivers seem to be loaded for it. lspci says: USB Controller: NEC Corporation Unknown device 0194 (rev 03) The vendor says the board is supported on Linux kernels 2.6.16 and later. uname says my kernel is 2.6.18-194.17.1.el5
How do I get this device to be recognised, and drivers loaded for it?
I've installed a new fresh Centos 5.5 ..and after a lot of work..something starts to work (X now works with the new ATI HD5145 using ATI drivers) but i've a serious problemThe ethernet controller JMC250 JMicron PCI EXPR. doesent work at all so my notebook is out of the world !!!Here is some infos:rpm -q centos-release
centos-release-5-5.el5.centos
rpm -qa kernel* | sort
kernel-devel-2.6.18-194.el5
[code]....
I have an old IBM Xseries 300 server that i can use. So, i am trying to install Centos 5.3, but during the installation , no disk can be found. I have 2 disks (1+1 in mirror) connected to an IBM serveraid PCI card.
I installed Debian Lenny, and it recognize the card (so the disks) immediatly.
~# lspci | grep RAID
00:09.0 RAID bus controller: IBM ServeRAID Controller
~# dmesg | grep scsi -i
[ 1.527963] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 3.092981] SCSI subsystem initialized
[Code]....
Does centos 5.4 support this?
product code: E10G41AT2
[url]
I am a newbie who's having trouble installing drivers for Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller.
I already have the drivers from my motherboard vendor, its just that i cant get them to run on my machine. I am running CentOS 5.5.....On the Sytem>Administration>Hardware (Device Manager) I can see the device listed. I am uploading the files for anyone who needs them. I know i need to run an rpmbuild, but i get errors when i try it..... also, i've tried to run atl1.rpm from ElRepo with no luck, i get an error saying Cannot find a valid baseurl for repo:
I am unable to find Atheros AR8132 PCI-E Ethernet Controller driver for CentOS which is installed on my netbook.
I contacted DELL to provide me the driver and they said that they do not support Linux on netbook and I have to arrange it myself.
I told them that I don't need help in installing I just need the driver file to which they said that they don't have driver for Linux.
NIC is getting detected and works fine on the same netbook (Am dual booting Windows7/CentOS) with Windows7
When I type: ls -l /dev/ it does not show up eth0. Same result with ifconfig. When I type lspci | grep net it does show up something like Atheros Communications AR8132 L1 PCI Gigabit .
I have spent them with Fedora and liked it a lot. Today I decided to install CentOS as this looks like something I would like to be using in the future. However a problem I could not solve came right at me after the first boot.
I have one eth0 device which is onboard lan and that was correctly recognised and activated. The second device is F5D5055 Belking USB Gigabit ethernet adapter. There was no problem with it whatsoever under Fedora. According to all the info it should be automatically recognised on kernel 2.6.14 and later. However when I plug it into the USB port, I can see its correct name in the device manager but it is not recognised as a network device. I have configured my Fedora as a firewall/router for my lan and definitely want to use that interface.
Hopefully without needing to do anything in the realm of compiling kernel, cause that is where my half a day long attempt to fix the problem left me.
from [URL]
i did the following
[root@localhost ~]# lspci | grep Wireless
0c:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
I can not get the node or cloud controllers to startup using the init.d scripts. I have a fresh install of CentOS 5.4 with Eucalyptus 1.6.2 I have compiled Eucalyptus and all packages using the RPM supplied from Eucalyptus and utilizing yum installer. I do not currently have any processes or applications listening currently on the ports on the boxes as well. I think it may be a permissions issue or something because I get a "permission denied error", but I am not sure if it is Eucalyptus or CentOS. It looks as if it is not binding to the address on the interface of the NIC. It may be something else however. I have the Node controller, Cloud controller, and Cluster controller on seperate physical boxes. When I try to run either the cloud controller or the node controller I get this message:
Cloud Controller:
[root@cluster-cont ~]# /etc/init.d/eucalyptus-cc start
Starting Eucalyptus cluster controller: (13)Permission denied: make_sock: could not bind to address [::]:8774
(13)Permission denied: make_sock: could not bind to address 0.0.0.0:8774
[code]...
I'm fairly new to fedora, and I installed it on my gateway kav60 netbook. Everything works fine, except that the wifi is saying that the firmware is missing. Is there a way to fix this?
View 1 Replies View RelatedI'm having a problem with the installation of Ubuntu Server 10.04 64bit on my IBM xSeries 346 Type 8840. During the installation the system won't recognize any disk, so it's asking which driver it should use for the RAID controller. There's a list of options, but nothing seems to work. I've been searching the IBM website for an appropriate driver, but there is no Ubuntu version (there is Red Hat, SUSE, etc). I was thinking about downloading the correct driver onto a floppy disk to finalize the installation, but apparently no 'general' Linux driver to solve the problem here.
View 1 Replies View RelatedI installed the 64-bit version of Fedora 12 on my MacBookPro5,1, and I am unable to establish a connection to my wireless network, which I can connect to fine with I boot the computer into Mac OS X. Here is my operating system information:
Code:
$ uname -a
Linux tosh 2.6.31.12-174.2.3.fc12.x86_64 #1 SMP Mon Jan 18 19:52:07 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux
Here is information about the PCI devices available on the system:
Code:
$ lspci
00:00.0 Host bridge: nVidia Corporation MCP79 Host Bridge (rev b1)
00:00.1 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
00:03.0 ISA bridge: nVidia Corporation MCP79 LPC Bridge (rev b3)
[code].....
However, I have the problem I can't see any devices on my IDE port in my Asrock P43 mainboard, because the VIA VT6415 IDE controller isn't recognized. I typed an 'lspci -k', and I can clearly see there wasn't loaded any module to handle this VIA PATA controller.
...
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
Kernel driver in use: r8169
[code].....
I'm using a "HuiJia USB Gamepad" to connect a standard N64 controller to my computer over USB. I'm doing this so that I can play games using mupen64plus, which uses the SDL to get input. My problem has to do with the way the adapter deals with C button events. Apparently, the u/d and l/r C buttons are treated by the adapter as joystick axes, so joystick events are generated by using them. But, for some reason, these events aren't recognized by SDL.
It gets stranger - if I cat the output of /dev/input/event5, the event gets printed when a C button is pressed. Furthermore, when I configure SDL to use the /dev/input/event* devices rather than /dev/input/js0, the C buttons are recognized! (Though, this leads to a situation where the joystick can't be calibrated... go figure). So, I can either have a correctly calibrated joystick with no C buttons or a miscalibrated joystick with working C buttons. Does anyone have any idea what I can do about this situation? The best outcome would be to force the C button joystick events to appear when using /dev/input/js0. Device as it appears in the output of lsusb:
[Code]...
I use Linux Mint Debian XFCE and there was a large update (lots of programs) I have done prior to rebooting. After reboot, my computer can now no longer find the ethernet controller anymore in lspci, so my wired connection no longer works.
Is this a hardware issue? The green lights are all blinking fine though.
I have an issue with my Sound on OS 11.2.It is correctly recognized under hardware and the driver seems to start properly as well when I do rcalsasound start.But under Control Center / Sound Preference there is no audio hardware listed (and hene no sound playing)
View 3 Replies View RelatedI just installed the latest version of Mint xfce on my old inspiron 8000 with a microsoft MN-120 pci ethernet card, and though the card shows up as hardware, it is not recognized as a network interface. I believe there is no driver loaded for it.
It's an old card, but it seems the kernel still supports it. There are instructions for activating the dc driver that appears to be the proper driver for this chip set, but those instructions originated from freebsd and I'm not sure they translate well. See here:[URL]
I did find a kernel config file, but I was afraid to add the suggested lines to it because there were no other lines specifying "devices". They all started with "config".
i am having issues with networking on a certain liveCD.all ubuntu installs ive done on this machine im sure work fine, but i may have had issues with older backtrack versions.My issue is no networking on boot of SamuraiWTF, for those unfamiliar its based on ubuntu 9.04 There is nothing except lo loopback when i run 'ifconfig', and there is nothing in /etc/network/interfaces for eth0 either.
lspci shows a Broadcom driver, but the same command shows the model number etc on a newer ubuntu install on the same machine. This is:
Broadcom NetLink BCM57780
I have the latest .tar.gz of the tg3 drivers suggested by Broadcom, but im lost on how to install them.
-------------------------------------------------------
EDIT: it seems to be an issue with earlier kernels, i installed 2.6.35 and it worked but the kernel isnt mean for 9.04 i dont think, and now theres issues with the nvidia card
I just bought a new server with one of the most recent v3 Intel processors (socket LGA1150). The board (Supermicro X10SLM-F) uses the new Intel NICs (i217LM + i210AT), not supported by the current Debian stable release. Hence, the ethernet adapter is not recognized during the installation process.
I would like to be able to install something as close to stable as possible in a production server such as this one.
ive installed ubuntu 11.04 and my broadcom wireless is not recognized.
View 8 Replies View RelatedI've an USB Network Controller product from China with no driver for Linux... It's seem in my FC10 not correctky fuctional... On Windows it worked as SR9600 USB To Fast Ethernet Adapter... here is my log...
Code:
[root@home ~]# dmesg | grep USB
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
[code].....
I have an ASUS P5Q PRO motherboard with an integrated Atheros AR8121/AR8113 PCI-E Gigabit Ethernet Adapter.I installed Ubuntu 10.04 "Lucid" 64bit Kernel version 2.6.32.21 I have read that the driver isn't in the kernel, but there's a strange thing :
First if I try to run lspci from command line it doesn't reports Atheros Ethernet Controller.
Second If I try to run lshw -C network from command line it doesn't reports Atheros Ethernet Controller.
Third if I run ifconfig it only returns my loopback address.
Can I suppose that my Ethernet Intel Gigabit Controller is broken or that Atheros driver is missing?
Well, when I run alsaconf, it finds my 82801H and I go on to setting it up, it says it will run, but it doesnt run.
Quote:
Now ALSA is ready to use.
For adjustment of volumes, use your favorite mixer.
But my song don't work, ..... works, but no sound in that, and i have tried running alsamixer to raise the volume to the peak.
I have a vague idea that, this sound card has difficulty in linux but all I get is 3 year old patches for gutsy gibbon and fixes that are non-slackware so I dont have the files and what not.
I have been trying, but never seem to understand why it says it works when it doesnt work.
Oh turns out, from thinkwiki, [url]
Its AD1984 actually, and it didn't work on 2.6.24.2 mine is 2.6.29.2 .
OS: Linux Mint 10 | Windows 7 Install Type: WUBI inside windows 7 Computer: HP Compaq Presario CQ56' Network: Realtek PCIe FE Family controller w/ Realtek 8102E chipset Problem in: Network Connection Issue: After I woke up my computer from Sleep, I lost ethernet. No connection. It told me that I had lost my connection. Why? Now, after several restarts, nothing.
View 14 Replies View Relateddoes someone know a workaround to solve this problem?[URL].. I'm trying to download all firmware on [URL]..I put them on usb key (they are about 12 files .deb) and, during the installation I choose "select driver from alternative" (or something like that) but never recognize it.Seems this card works with tg3 driver but i'm not sure.If there are no way to recognize it from installer, could someone please suggest me an alternative way to install testing on my notebook ?
View 6 Replies View RelatedI am using fedora core 2. I used the oldest version of fedora just because im running only 1 system, my specification is: HP compaq PC,pentuim4, 512mb memory, 40gig hdd, Intel board. I have two units same spec..windows xp and the other one is fedora 2. The windows xp normally detect the lan card, but when I try to fedora2, I try to active it and seems no lan card detecting,. How to detect broadcom nextreme gigabit ethernet to my fedora 2 OS???
View 7 Replies View Related