Hardware :: Installing Ethernet Driver Returns Error
Mar 22, 2011
I recently installed my redhat 6.0 and there was no internet connection so i read some threads that guided me to try and detect my network card which detected nothing. I then went ahead to download ethernet realtek ethernet gigabyte card driver for my version of linux. I untar the file and i got the directory r8168-x.x.xxx.xx, a README file so i read the README file and it asked me to run ./autorun.sh which i did but i got the following error:
View 14 Replies
ADVERTISEMENT
Jan 2, 2010
I have a Dell Inspiron E1505, which has the Dell Wireless 1505 (Broadcom) card. To run the card, I installed the Broadcom STA wireless driver, which seems to activate the wireless card OK. The problem is that once I installed that driver my onboard Ethernet card was deactivated (and yes, it is enabled in BIOS). I had to remove the wireless driver to get the Ethernet back. Does anyone have ideas? I haven't found this problem listed elsewhere. I am running Ubuntu 9.04 with no other problems.
View 5 Replies
View Related
Sep 22, 2010
I tried to compile Atheros AR8152 PCI-E Fast Ethernet Controller driver for fedora 13 64 bit kernel version is 2.6.34.7-56.fc13.x86_64. I have installed kernel source , kernel header and necessary all things to compile it. (linux-firmware-20100806-4.fc13.noarch also installed). I tried AR81Family-linux-v1.0.1.13 source from Atheros web site.
But when I try to make it it give following error.
Code: Makefile:173: *** *** Aborting the build. ***
This driver is not supported on kernel versions older than 2.4.0. Stop. It is not compiling issue because I compiled and installed broadcom wireless driver.
Makefile is attached here (renamed as Makefile.txt -> Makefile)
View 5 Replies
View Related
Apr 6, 2011
I am trying to reinstall ATI propietary graphics driver fglrx on Xorg 1.10.0.901, but it always fails with (something similar to): Code: ./default_policy.sh does not support version default:v2:x86_64:lib32:none:[my kernel] make sure that version is correctly set by --iscurrentdistro
I am not sure what is it trying to tell me, neither I don't know why lib32 is in the list. (It's 64bit Gentoo system). It used to work in past, but now I can't start X at all. Using my already installed driver produces Segmentation fault, X without any configuration stops on no devices found.
EDIT: Alright, I just discovered that fglrx driver does not support higher versions of X.org than 7.6, and I have 1.10.0.901 version installed. EDIT2: Actually, later I found out that my Xorg is supported by that driver, so I think it was the mess in packages&Xorg configuration which caused it. Nevermind...
View 1 Replies
View Related
Mar 21, 2011
I'm working with OpenSusse 11.2. I installed and activated the NFS server via yast2. I exported the relevant directory via yast2 (NFS server configurastion)
I'm trying to setup my Linux target to boot via NFS. The kernel boots up but fails to mount the file system. When looking on a capture from ethereal it can be found that the NFS server return error when client try to mount the /nfstest directory from this server. The returned error is 13
serverip: 192.168.56.130
targetip: 192.168.20.180
gateway: 192.168.20.101
[Code].....
View 1 Replies
View Related
Jan 21, 2010
I am trying to install xorg-driver-fglrx using apt--get but it return error which says btw i am using ubuntu8.10 Desktop distribution
Code:
root@VAIO:/home/miriyala# apt-get install xorg-driver-fglrx
Reading package lists... Done
Building dependency tree
Reading state information... Done
[Code]...
View 2 Replies
View Related
Jun 5, 2010
I have acer laptop with ATI Mobility Radeon HD 5470 graphics card. I have downloaded ATI Radeon 5xxx driver from ati official site. When I ran it using the command below, it gives me the following error
command:
Error:
Removing temporary directory: fglrx-install.OiFpw4
View 14 Replies
View Related
Sep 10, 2010
error: No output seen in over 300 sec... (Is the CD-ROM/DVD source repository enabled? It shouldn't be!) error: Package install command failed with error code 255 Would you like to retry installing the missing package(s) (y=yes*, n=no, q=quit) ?
I've tried this [URL] but it didn't work for me. My sources.list already had the #. By the way I'm a new user to ubuntu and I'm having a pretty good time. Almost starting to feel at home in this OS. edit: I'm sorry. I realized I posted in the wrong section.
View 2 Replies
View Related
Nov 5, 2010
10.10) now, and only use windows as my DVR (what im currently trying to change). To that end, i have a Hauppauge 2250 video capture card, and Steven at KernalLabs has an alpha release that has been said to work very well with mythTV.
Anyways, i followed one of the posts and successfully compiled the driver using "sudo make menuconfig." I attempted to install with the "make install" command, and the first half of the driver seemed to install and the second half (firmware related) received errors.
make -C firmware install
make[2]: Entering directory `/home/mlavigne/saa7164-v4l/v4l/firmware
Installing firmwares at /lib/firmware: vicam/firmware.fw cp: cannot stat `vicam/firmware.fw: No such file or directory
dabusb/firmware.fw cp: cannot stat `dabusb/firmware.fw: No such file or directory
dabusb/bitstream.bin cp: cannot stat `dabusb/bitstream.bin: No such file or directory
ttusb-budget/dspbootcode.bin cp: cannot stat `ttusb-budget/dspbootcode.bin: No such file or directory
[Code]..
View 3 Replies
View Related
Jan 20, 2010
I am new to Linux, but I can't produce any sound out of my speakers. So I downloaded the driver for my sound card from my motherboard manufacturer (it is an on board sound card). Now, if I am right I need to run ./configure . I did this and the following thing happend: Code: checking for gcc gcc
checking for C compiler default output... a.out
checking whether the C compiler works... yes
checking whether we are cross compiling... no
checking for executable suffix...
checking for object suffix... o
checking whether we are using the GNU C compiler... yes
checking whether gcc accepts -g... yes
[Code]...
View 7 Replies
View Related
Nov 28, 2008
I selected the zc0301 driver as module when i compile the kernel...and i copied the "zc0301.ko" file from default kernel...but when insert using "insmod" its not working..showing the error..
insmod: error inserting 'zc0301.ko': -1 Invalid module format
How to insert this driver?
View 9 Replies
View Related
Mar 17, 2010
The relevant details of my setup are:
Samsung R522 laptop
Realtek RTL8192E wireless network controller (PCI)
Fedora 12, kernel 2.6.32.9-70.fc12.i686 (automatically updated using software update)
My problem is that my wireless card has never worked - basically there aren't any widely available linux drivers, and there are many threads on getting the RTL8192E to work on many different forums, e.g. here, but none specifically for Fedora, so I think that this thread could potentially guide many more users. FYI, my hardwired network connection works perfectly.
Fantastically however, by emailing Realtek support, they'll send you their Linux driver, which most people have claimed works perfectly (although why they haven't just put it on their website is beyond me). SO, I've got a Linux driver for my wireless card. When Realtek emailed me to send me the driver, they said to just 'cd' into the driver directory, then do
su
make clean
make
make install
reboot
./wlan0up or ./wlan1up
OK, so I tried to do this and get the following error:
make: *** /lib/modules/2.6.32.9-70.fc12.i686/build: No such file or directory. Stop.
make: *** [all] Error 2
I don't know enough about linux to understand this error. I really don't want to have to recompile my kernel, and I hope there is some way to install this driver with not too much hassle. How to overcome this error, and install my wireless driver so I can get wireless network access on my Fedora 12 operating system. I've found Fedora 12 really easy to use so far, but this is proving quite hard!
This is the output of 'ls -lh' in the folder which seems to be causing the error, namely /lib/modules/2.6.32.9-70.fc12.i686/
total 3.1M
lrwxrwxrwx 1 root root 46 2010-03-16 22:53 build -> ../../../usr/src/kernels/2.6.32.9-70.fc12.i686
drwxr-xr-x 2 root root 4.0K 2010-03-03 05:28 extra
drwxr-xr-x 11 root root 4.0K 2010-03-16 22:53 kernel
-rw-r--r-- 1 root root 498K 2010-03-16 22:53 modules.alias .....
View 7 Replies
View Related
Apr 28, 2010
I revived my old desktop (failed psu), and installed debian squeeze using netinst. It has a nvidia geForce 7600GT card. The driver in squeeze does not work very well, so I downloaded nvidia driver-installer. When I run it, it comes back with an error saying the kernel (I assume the nvidia graphics kernel) is compiled with gcc4.3, but the system is using gcc4.4. Using synaptic manager, I installed gcc3.3, but same error.
Next I tried to uninstall gcc4.4 and it gave a warning the system might not be usable. I did not understand it, but I went ahead and uninstalled gcc4.4 and guess what, the system is not usable, and I have to re-install squeeze. Not a big loss, since I do not have much in it. How to install this nvidia driver, specifically, how do I get switch to gcc4.3 from gcc4.3? Also, the squeeze install gave me 2.6.33-trunk-amd64, and 2.6.33-3-amd64. How do I get rid of ...trunk-amd64? Do I just delete it from grub?
View 10 Replies
View Related
Apr 13, 2011
I am relatively new to linux and am running into a problem. I just got a new laptop and need to configure/install it's wireless driver but am getting an error when running "make". The error is: make[1]: Entering directory `/lib/modules/2.6.37.1-1.2-desktop/build' make[1]: *** No rule to make target `modules'. Stop.
I have scoured these forums and know that others have the same issue (when configuring other drivers/programs). I am sorry if this post is redundant. It sounds like the Makefile is pointing to the wrong directory. I am using opensuse 11.4, have make and gcc installed. My kernel is linux-2.6.37.1-1.2 (I just re-installed the desktop kernel to make sure it was up to date). The driver I am trying to install is located here: AUR (en) - rtl8192ce.
Another forum suggests pointing somewhere in the /usr/src/linux-2.6.37.1-1.2 directory instead. Is this correct? Should I be pointing to a folder within this? I am not a programmer but any description about what I am actually putting in this directory and why would be awesome (so I can learn a bit more). Or just helping me solve the problem would be great too.
View 9 Replies
View Related
Nov 6, 2010
I have completed building gazebo, and everything was done successfully according to the following link [URL]... bot_Simulation , but when I tried to invoke gazebo using the command "gazebo /usr/local/share/gazebo/worlds/pioneer2dx.world" it returns the following error
[code]...
View 1 Replies
View Related
Mar 11, 2011
I am unable to run firefox on my Hp mini 110 running FC14. This happened, I think, after an update that I have done.
When ever I run firefox I get the following messages.
Code:
View 5 Replies
View Related
May 9, 2011
I am using Fedora 14 (64 bit version): Can't Start XAWTV. Returns the error.
$ xawtv
This is xawtv-3.99.rc6, running on Linux/x86_64 (2.6.35.12-90.fc14.x86_64)
xinerama 0: 1920x1080+0+0
WARNING: No DGA direct video mode for this display.
WARNING: keeping fbuf pitch at: 7680, as no base addr was detected
WARNING: couldn't find framebuffer base address, try manual
configuration ("v4l-conf -a <addr>")
v4l2: WARNING: framebuffer base address mismatch
v4l2: me=(nil) v4l=(nil)
Warning: Missing charsets in String to FontSet conversion
Warning: Missing charsets in String to FontSet conversion
Oops: can't load any font
View 1 Replies
View Related
Feb 26, 2010
I have a service on my Suse 11 server which runs an ssh command (using openSSH) on another box.The output below is returned, but legitimate output is also returned as if the command had executed successfully. For example, the service executes an ls command through ssh, gets the error below, but also the contents of the remote directory as output. This is a problem because the service retries the command until it receives no error. I have been unable to replicate this manually from the command line. Does anyone know what might cause this or what this error really means?
View 5 Replies
View Related
Jul 27, 2011
I have installed in my opensuse 11.4 the kdesvn.
When I press the checkout button the program crashes and returns the following message:
View 1 Replies
View Related
May 21, 2011
I have a new Debian Linux 6.0 server installed, running Linux 2.6.38.3-linode32 on i686. It has apache2 on front.
The master plan was to run Railo on this one, so I can continue my mad Coldfusion schemes to rule the world, so got the tomcat set up with it, as instructed by some guy I met on a chat. He seemed very reliable.
I got the whole thing working, can view my regular html files and whatnot, but as soon as I try to run a cfm file,
I get an error message on screen:
I have no idea whatsoever what to do next. This is my site with the html file:[url] and here is my test index.cfm file:[url]
View 1 Replies
View Related
Nov 1, 2010
I'm having a little problem here. That, or I'm missing the obvious staring me in the face. I have this file server, called toad. I nuked it's system disk, reorganising the partitions and upgrading to openSUSE 11.3 x64. I installed vsftd with "Yast FTP server", and the config looks OK. I even compared it with that of another machine. But when I try to connect, this is what I get:
user@mainmachine:~> ftp
ftp> open toad
Connected to toad.geuens.org.
500 OOPS: could not bind listening IPv6 socket
I'm prettige sure IPv6 is deactivated. The firewall is disabled on both machines. I've looked this over again and again. Can't find it. It's not the connecting machine, I've tried from another.
View 4 Replies
View Related
May 13, 2011
Running start_navicat script in kubuntu 11.04 returns bash error ./start_navicat: 10: arithmetic expression: expecting EOF: "2*100+13 2". The same navicat version runs fine in ubuntu 10.10 and 10.04. I tried deleting navicat folders - including hidden folders and reinstalling, but get the same error.Can't test ubuntu 11.04 because i can't get it running (black screen - even grub). xubuntu 11.04 is very unstable too. kubuntu 11.04 is very stable otherwise.no idea what to do, other than continue using ubuntu 10.10 (which is the best ubuntu version to date imho)
View 5 Replies
View Related
Apr 9, 2010
The system is Debian Squeeze/Sid with apt.conf set to Squeeze as the default. Most packages are from Squeeze.
I ran apt-get upgrade and it returned an error-code.
It might be it is this bug: Bug#574153: python-pkg-resources: Missing file leaves it unconfigured
I tried aptitude install -f, to hold it and to remove the package python-pkg-resources, but i am getting told the package would be in a very bad stage, and i should re-install it. That doesn't work.
View 1 Replies
View Related
Jan 19, 2010
I am trying to install wxpython from source package when ran ./configure command it came up with a strange message which says
Code:
Code:
View 8 Replies
View Related
Mar 21, 2011
For some reason the script below works fine when I run it directly but when I run is using source, I get a not found error?
With source: (line 11 is where the 'test' statement is)
Quote:
gtonder@sydlnx03:~> source set_aliases.sh -v 11:31AM
1
set_aliases.sh
[Code].....
View 6 Replies
View Related
Apr 6, 2010
I ran into this:[url]
I tried to ignore it (yesterday it made me remove xmms2-plugin-all, i could have lived with that for a few days), but it is getting worse: gnomebaker, mpg123, vorbis-tools, cdrdao, etc.
So i remove beloved apps , run aptitude install -f and what not. The result is that either libao2 or libao4 give me trouble (depending which version is installed at that moment).
After the upgrades are available again it's big fun over here. Is it just me or are others running in a lot of "dpkg returned an error message" too? The first time ever i got to use aptitude to get problems solved. Gnome terminal gives me segmentation fault but no error messages. And so on.
View 3 Replies
View Related
Jul 12, 2010
I'm simply trying to compile a vanilla kernel from Kernel.org, I've done it before, however "make menuconfig" returns an error after I've made my changes to the config file.
Code:
Why is make returning that error? I am using a 64-bit kernel.
View 2 Replies
View Related
Jul 17, 2011
I'm trying to burn an audio CD with Brasero. Every time I try this, it fails, but it works when writing to an image file. Brasero quits with the following messages in log:
Code:
Checking session consistency (brasero_burn_check_session_consistency brasero-burn.c:1744)
Unsupported type of task operation
Session error : An internal error occurred (brasero_burn_record brasero-burn.c:2862)
Do you know what could be causing this?
View 5 Replies
View Related
Mar 20, 2011
When I type the command
Code:
startvnc
I get the following error
[code]....
View 8 Replies
View Related
Oct 31, 2010
Code:
kenny_strawn@kenny-AOA110:~$ sqlite3 -html -line /var/www/fluxbb/ProprietarySuckware 'select o_base_url from memos'
Error: unable to open database "/var/www/fluxbb/ProprietarySuckware": unable to open database file
kenny_strawn@kenny-AOA110:~$
This database was automatically generated by FluxBB, so I am wondering just why it isn't opening.
View 2 Replies
View Related
