Hardware :: CUPS And HP LaserJet P1505n - Green Button Press Required For Printing
Feb 21, 2011
At work I've got a HP LaserJet P1505n printer that is used as network printer. It has an ethernet port and is plugged in directly into the network. Everybody in the office is using Windows and has no problems working with it. After a few hours of google-ing, I also managed to set it up with CUPS as a LPD printer, with some problems: every time I send a document to it, it goes into the "error" state, and I have to press the "green" button for the printer to start printing. Is there a way to work around these errors? I tried to google for these kind of errors, but couldn't find anything useful.
My printer is a HP laserjet 4 Plus. It used to work with the gutenprint drivers pretty much since always.I don't know when it broke, because I don't use it that often. I have tried with the generic postscript driver, with the gutenprint driver, with the j4dith driver and with the hplib driver. Basically, what happens is that all jobs never finish processing in the queue. On the other hand cups-pdf still works.
I'm converting my coworker to Linux (who loves it) and I've gotten everything working but this %$#@ printer! I've tried the various solutions posted on these forums (over the past 4 or 5 years). But none of them seem to work.Has anyone solved this problem with Lucid (10.04)? Are there some new steps that pertain to 10.04?
Inherited an old Laserjet 6P that was working fine XP. No matter which printer driver I use all I get are pages and pages of garbage during the test print. I have tried the hplip, gimp, ljet4 drivers without success. I have tried sending text files from the command line as well (cat /etc/passwd > /dev/lp0) with the same result.
Fedora 11 64 cups 1.4 hplip-3.9 hpijs-3.9
Anyone using this printer with cups 1.4? Any ideas which driver to use?
i recently installed fedora 14 xfce and i have a printer laserjet p1007 hp connected. the printer gets detected but there is an error while installation (i.e when i run hp-setup) it gives an error that some binary drivers missing. i refreshed the package list also. but still the driver does not get installed..
I am using gqview as an image viewer (under Debian Lenny). When I use gqview to print files to a HP LaserJet 5P printer, the dithering of graphics is quite coarse (click for view of printout scanned at 300dpi): gqview.jpg
On the other hand, if I use gimp to print it, the output is normal (click for view of printout scanned at 300dpi): gimp.jpg
I have tried changing the CUPS resolution settings for the printer (they are set to grayscale 600dpi), and the resolution setting in gqview (also set to 600dpi), but this doesn't help. Printing to a different printer (HP LaserJet 2605) does not exhibit the same behaviour!
I am running 64bit Ubuntu and have just installed XBMC and the install has gone great so far. Easy to set up and configure and all my media now works. I have installed lircrc and my remote works when in XBMC.
I have created a file .lircrc in my home share and added the following
begin remote = mceusb button = Home prog = irexec repeat = 0 config = /usr/share/applications/XBMC Media Center end
i use ubuntu 10.04.its working quite normally.i installed ubuntu tweak and compiz fusion etc.For a few days i didn't have any problem.but after some time in the case of ubuntu tweak,i am unable to press the 'unlock' button.its as if its freezed or something.nothing will happen.in the case of compiz fusion i am unable to change its settings and change the effects.the software center application which is one of the default applications, i am unable to install a thing.the install button there is also freezed.like wise i think my super powers have gone automatically.but when i checked the users and admin settings i still have the super powers and i am the administrator.so i deleted that user and made an another user.
Is it possible to have the power button emulate the press of a key? On my media centre I have XBMC running and it doesn't recognise me pressing the power button. If I press S (on the keyboard) the shutdown menu pops up.
Is there a button I can press when booting to log into a 'safe mode' ? Like f5-f6 does on windows? Or a command prompt? My ubuntu fails when it loads X and cant get out of it, is there something I can do to allow me to log into the system to see whats the problem or revert it back to the old settings?
1) check if a mouse button is pressed down. I need to check this status of mouse button again and again inside a loop. Depending on the status, some function will be called. OR
2) check if some key of the keyboard is pressed down. I need to check this status of 'key' again and again inside a loop. Depending on the status, some function will be called.
openSuse 11.4 64bit fresh install, KDE 4.6.0. Now I am probably being obtuse, but If I click on the wonderfully named "My Computer" I get, among other things, a display of Disk Information; hard drive partitions and any DVDs or CDs. If I let my mouse cursor alight on any of these, I get a message "Press the right mouse button for more options (such as Mount or Eject)" But if I press the right mouse button, I don't get those options; I get a message "Open in new window, Open in new tab, Open with ..., Create file project with K3b, and Compress ...".
My Update Manager stopped working for last three weeks. When I press button INSTALL UPDATES in Update Manager, nothing happens just Reading packing information is executed and when it is finished nothing continues,so nothing I chosen is installed. I have tried to fix broken packages in Synaptic Manager, but no change.
I am a new user of ubuntu and have found that the Update Manager freezes when I press Install Updates button. what to do next as I am way behind with the updates.
It seems that they are not shown under xev ...Someone knows if old scanner, can be detected in terms of button pressing ?[URL]button pressing does not show up into deamon.log
I've been switching out computers to the Ubuntu distro and so far it's been very successful until this recent snag! As I am trying to have a printer plugged in through USB on one computer and shared on the other! I have the USB on the second computer and it found the printer just fine, no problems and nothing else I had to install! I then went to the first computer and tried to add the printer through the CUPS website using all the proper addresses and queue names and I receive CUPS "client-error-not-possible". I have read other threads on this very same problem but to be honest they just make no sense whatsoever to me! I was thinking of just giving up and using a print server but I know that I will run into the same snag as even then I still need CUPS.
Not sure if this is hardware or software so I am raising the question here. I have an Ithaca 280 printer that worked great on fedora 8 with cups 1.3.3. When I upgraded my server and installed Fedora 12 with cups 1.4.2 i noticed a 5 second delay between sending a print job to the printer and it actually printing. This issue doesnt happen with laser printers, just the ithaca thermal printer. I have tested this with 10 other ithaca 280 printers and all of them have the same result. I am using a raw driver, and it is an IP based printer setup for Jetdirect in cups. The setup is identical on a Fedora 8 server as it is on this Fedora 12 server. I have even taken the steps to upgrade to cups 1.4.4 just to see if it was corrected in a newer version, but the issue is still there. I have a utility that writes the raw text directly to the printer which i used to test that it wasnt an issue with the printer or its internal print server. That utility allows the document to print immediately.
what is causing this delay and how to correct it? If not, does anyone know how to print directly to the printer using cups instead of letting it go to the queue first like cups normally does for print jobs?
Anyway im trying to do a simple thing pointed out in the thread title. Everything is set up, cups-pdf works, in dosemu.conf lpt1 command is "lpr" printer-timeout is 10... I "work" in an accounting agency that has a program written in clipper back in 1992. Apparently some prints from this program produce text/plain and some produce application/octet-stream. text/plain is printed. The later is always aborted. I have uncommented the lines in mime.types and mime.convs. Which are located in /usr/share/cups/mime.
I'm not looking to setup a print server. I want to print documents TO an existing network printer while I'm logged in via ssh to my Ubuntu Server 10.4 command line shell. Things like admin emails, pdf docs, etc.
All the clients on my LAN are able to print directly to the network printer without any help from the Ubuntu Server. I don't want to setup CUPS on the server unless that's the only way to print from the server itself to a networked printer.
Do I need CUPS or can I print from the command line in some other way?
I'm doing work at a home office that uses all Ubuntu computers. They have wireless printing setup on a few computers using CUPS. One of the computer's wireless printing isn't working. could someone please help me with getting this set up? Is this something really basic that most people would understand how to do?
I just brought up a new server on RHEL4 to replace an existing older one. The server is using CUPS for printing. I copied the cupsd.conf, printers.conf, and lpoptions files over from the old server. I also copied the printer files in the /etc/cups/ppd directory over to the new server. But I can't get printing to work. And when I run system-config-printer-tui I don't see any of the printers in the dialog box. What other file(s) am I missing?
Using Debian Lenny.Using CUPS and lp. I would like to know how to print files from Openoffice such as doc files, pdf and html. I know I can print from the applications, but sometimes I want to print using lp or xpp. I would like to also set the font size on pdf or html pages before I print. I never know what size of print I'm going to get. Can I chose the font I want to use in text files with Cups?
Is there an option to hide and unhide hidden files inside nautilous with a press of a button?And without the need to browse the edit-preferences-etc all the time?
I am doing work at an office that only uses Linux Ubuntu 9.10 . They have wireless printing setup on all of the computers there, except one of them isn't working. I was not the one who setup the wireless printers so I'm not clear on how to do this.
I am facing a peculiar issue when printing Japanese text through CUPS (though I am not sure if this is the right forum).
I developed a Java application (that uses a graphical object to print to a PrinterJob class) that prints text (of Japanese characters) to a printer. When I login in en_US/en_UK locale, the Japanese characters get printed from my Java app just fine. However, when I login in ja_JP and give a print job through my Java app, no Japanese text is printed at all. I get characters from only within the ASCII subset printed instead. I am using Serif and Courier New fonts in my app. Relevant details are:
In ja_JP, a@a:/usr/share/cups/charsets$ fc-match serif:lang=ja ttf-japanese-mincho.ttf: "Sazanami Mincho" "Regular" a@a:/usr/share/cups/charsets$ fc-match sans serif:lang=ja ttf-japanese-gothic.ttf: "VL Gothic" "regular"
