Software :: Gqview Printing To HP LaserJet 5P Gives Coarse Dithering

Oct 20, 2009

I am using gqview as an image viewer (under Debian Lenny). When I use gqview to print files to a HP LaserJet 5P printer, the dithering of graphics is quite coarse (click for view of printout scanned at 300dpi): gqview.jpg

On the other hand, if I use gimp to print it, the output is normal (click for view of printout scanned at 300dpi): gimp.jpg

I have tried changing the CUPS resolution settings for the printer (they are set to grayscale 600dpi), and the resolution setting in gqview (also set to 600dpi), but this doesn't help. Printing to a different printer (HP LaserJet 2605) does not exhibit the same behaviour!

View 8 Replies


ADVERTISEMENT

Ubuntu :: HP LaserJet 1000 Not Printing On Lucid?

Aug 17, 2010

I'm converting my coworker to Linux (who loves it) and I've gotten everything working but this %$#@ printer! I've tried the various solutions posted on these forums (over the past 4 or 5 years). But none of them seem to work.Has anyone solved this problem with Lucid (10.04)? Are there some new steps that pertain to 10.04?

View 2 Replies View Related

Hardware :: LaserJet 6P Printing Pages Of Garbage

Nov 2, 2009

Inherited an old Laserjet 6P that was working fine XP. No matter which printer driver I use all I get are pages and pages of garbage during the test print. I have tried the hplip, gimp, ljet4 drivers without success. I have tried sending text files from the command line as well (cat /etc/passwd > /dev/lp0) with the same result.

Fedora 11 64
cups 1.4
hplip-3.9
hpijs-3.9

Anyone using this printer with cups 1.4? Any ideas which driver to use?

View 4 Replies View Related

CentOS 5 :: Slow Printing On HP Laserjet 2100?

Aug 25, 2010

I just installed CentOS on my Compaq desktop pc with HP laserjet 2100 printer on parallel port.However it takes an extremely long time to print.

View 3 Replies View Related

Fedora Hardware :: Hp Laserjet P1007 Printer Not Printing?

May 29, 2011

i recently installed fedora 14 xfce and i have a printer laserjet p1007 hp connected. the printer gets detected but there is an error while installation (i.e when i run hp-setup) it gives an error that some binary drivers missing. i refreshed the package list also. but still the driver does not get installed..

View 1 Replies View Related

Hardware :: CUPS And HP LaserJet P1505n - Green Button Press Required For Printing

Feb 21, 2011

At work I've got a HP LaserJet P1505n printer that is used as network printer. It has an ethernet port and is plugged in directly into the network. Everybody in the office is using Windows and has no problems working with it. After a few hours of google-ing, I also managed to set it up with CUPS as a LPD printer, with some problems: every time I send a document to it, it goes into the "error" state, and I have to press the "green" button for the printer to start printing. Is there a way to work around these errors? I tried to google for these kind of errors, but couldn't find anything useful.

View 3 Replies View Related

Networking :: Training Coarse In LDAP Integration?

Jul 9, 2009

Has any taken and/or recommend a coarse in LDAP integration? I would love if I could make my labs a single sign-on.

View 4 Replies View Related

Slackware :: Remove Gqview And Add Geeqie In Next?

Mar 6, 2010

Slackware includes gqview, a pictures viewer not maintained since 2006. Geeqie is a fork of gqview and the first stable version is out since about 1 month, and it seems to be stable and good. So what about remove gqview and add geeqie in next slackware ?

View 14 Replies View Related

General :: Start Gqview From Windows Over SSH With Putty / Plink

Jan 10, 2010

I'm trying to figure out how to start/stop gqview remotely from a batch script on a windows machine. Stopping works with killall but starting gives me a
Code: Gtk-Warning **: cannot open display warning.
Is this because it tries to open a GUI in the terminal and if so how to solve this?

View 4 Replies View Related

Software :: GQView - Change / Edit Mouse Button Shortcut?

Feb 1, 2010

When using the above image viewer, it would be easier for me to be able to close the viewer/image while displaying an image in fullscreen mode, by clicking on the middle mouse button, rather than right clicking and choosing "Exit full screen", then clicking on the cross in the corner of the window. This is similar to how Firefox can close tabs by middle-clicking with the mouse wheel.

Mouse function editing in GQview seems limited to controlling whether the scroll wheel pans up and down the picture, or moves to the next/previous picture. Any way I can edit the preferences file for GQview at .gqview/gqviewrc in order to achieve the above shortcut facility on my mousewheel, for this application? Or is anyone familiar with another Linux image viewer that does allow the mouse to be programmed in this way?

View 2 Replies View Related

Hardware :: Continuos Printing - Stop Ejecting The Paper After Printing Over?

Jul 28, 2010

We developed qt based application in linux. I wish to stop ejecting the paper after printing over.How to do it.

View 2 Replies View Related

Ubuntu :: Printing With Exact Size Photos And With Poor Auto Colour Printing But The Situation Remains Unchanged

May 31, 2010

I expected more from ubuntu 10.4 with regards to printing with exact size photos and with poor auto colour printing but the situation remains unchanged! for instance .. the photo size configurations for ubuntu/fspot/gimp and others are not compatible with my printers (HP and Brother) .. here in Europe a typical standard size photo (10x15inches or 150x100mm are not even on the Ubuntu listing? I have tried all listed possibilities including "custom" (which does not seem to ever work correctly?)and the result at best is photos with uneven boarders or at worse my printer goes a bit crazy with much wasted photo paper and expensive ink ...even photos selected for "no boarders" still produces photos with the self same uneven boarders.

I have tried pretty much everything over time following advice in this forum and including using HPlip and updating drivers required for my Brother printer but the root problem seemingly lies with the Ubunto photo size setup listing. Working with Ubuntu over the years I have found that it can do pretty much everything that Windows can do except for this dam ongoing photo quality and configuration problem.

View 9 Replies View Related

Fedora :: 13 - Support For HP Laserjet P2035

Jul 26, 2010

Under Fedora 12, the HP laserjet p2035 is supported. It appears under HP>Laserjet as a dirver option when setting up the printer. But all the HP driver options except two havedisiappeared under Fedora 13 (64 bit version).

I may be missing some package, but if so I don't know what. I didn't have to do anything special, I think, for Fedora 12.

Also, I can't set up the printer as a windows printer. I don't know if it is because none of the driver options work or because of something else. I often have problems setting up remote printing with a new release, so I expected this. But I'm not sure where to begin troubleshooting.

View 10 Replies View Related

General :: How To Configure HP LaserJet P1102w

Aug 5, 2011

Who know how confiure a HP LaserJet P1102w on bebian 6?

View 3 Replies View Related

Slackware :: Setup The HP Laserjet P1005 On 13.1?

Aug 31, 2010

how can i setup the HP Laserjet P1005 on slackware 13.1 ?

View 5 Replies View Related

Ubuntu :: HP Laserjet Doesn't Work With 10.04?

Jul 7, 2010

Is anyone else having problems with HP LaserJets and Ubuntu 10.04? I have a HP LaserJet 3015 and am running a dual boot with Windows 7.

Printer is automatically detected and works fine on: Windows 7, Windows XP, LinuxMint, and older versions of Ubuntu.

But when I'm running Ubuntu 10.04, when I try to print it just adds the job to the print queue and it never prints. After awhile I get a message saying that Ubuntu is unable to communicate with my printer. (or something to that effect). I can't even print a test page.

I have tried installing HPLIP following the directions given, but get the same behavior (can't communicate with the printer). I have tried unplugging the power cord and usb cable and plugging them back in (as per the directions I am following). But still not communicating.

View 7 Replies View Related

Debian :: CUPS Stopped Working With HP LaserJet 4 Plus

Jun 22, 2010

My printer is a HP laserjet 4 Plus. It used to work with the gutenprint drivers pretty much since always.I don't know when it broke, because I don't use it that often. I have tried with the generic postscript driver, with the gutenprint driver, with the j4dith driver and with the hplib driver. Basically, what happens is that all jobs never finish processing in the queue. On the other hand cups-pdf still works.

View 14 Replies View Related

Debian :: Hp Laserjet 1020 Doesn't Print

Feb 2, 2010

I have tried to download the latest version of CUPS but do not know how to install it properly using command line commands above 'sudo' and 'sh', and I have tried to install HPLIP but it needs 'cups-devel' installed apparently. My Debian can see the 1020 clearly enough to identify it and give its status as idle, via the CUPS interface. When I try and print a Test page it goes to the spooler, says it is printing OK, but nothing prints. The job then disappears and appears on CUPS as completed. In the old days we would have sent a eof() to make the printer work. Have I got a bug in my HP Laserjet 1020 driver? Or am I missing the great plug-in that is not on the Synaptic Package Manager The SPM says I have HPLIP installed.

View 5 Replies View Related

Fedora Hardware :: Can't Get HP Laserjet P1006 To Work On 11

Nov 13, 2009

I've searched these forums high and low, but I can't seem to find a way to fix it. I had a similar problem in F10, but that was fixed. The problem I'm having now is a little bit different. If I open the print que before I print something like a test page, and then start printing, an item with appear in the que for a second then disappears, and the printer will do nothing. I've run out of ideas on how to get it to work, I did try to apply the original fix for my first problem since it seemed that the drivers for the Printer that were available via HP weren't quite right, but that didn't work. I tried to run -c 'yum install foo2zjs' and that didn't do anything either.

View 2 Replies View Related

Fedora Hardware :: Hp Laserjet On F13 Not Working On Network

Sep 6, 2010

I have a hp officejet on my fedora 13 pc. I tried to configure it as a network printer. I disabled selinux and then i opend the door in the firewall.. the printer is seen in the network but when I try to print from a client it says "printer description not available" . I disabled then firewall both on server and on client. then rebooted both. but no luck. the printer is available on the network but it prints only from the server.

View 2 Replies View Related

Fedora Hardware :: F15: HP LaserJet 5MP Printer Not Connected

Apr 23, 2011

I am running F15 Beta i686 (Gnome3) Desktop on a dual-core, 4 Mb DDR2 system. I already installed hplip and hpijs drivers and connected HP LaserJet 5MP printer to the parallel port of my PC. Set up was by running "system-config-printer", adding device URI=parallel:/dev/lp0, and selecting approriate driver (CUPS+Gutenprint (en) for the printer. However, when I chose to print a test page, nothing came out and the printer window says the printer is not connected. This is even though I can print from Fedora14 installed on the same PC.

View 2 Replies View Related

Fedora Hardware :: Hp Laserjet 1015 Not Detected?

Jun 3, 2011

I am having problem printing some urgent documents. My fc14 machine cannot seem to see the printer. I remember on an earlier version it was a breeze ...I connected the printer and immediately the machine recognized it.I spent 2 hours trying to install hplip-gui.i686 0:3.11.5-1.fc14 successfully but yet the machine cannot see the printer.---------- Post added 3rd June 2011 at 08:16 AM ---------- Previous post was 2nd June 2011 at 11:59 PM ----------

View 8 Replies View Related

Ubuntu :: HP Laserjet 1320 Printer Won't Work

Oct 21, 2010

I have been given a HP laserjet 1320 printer. how to make it work?

View 9 Replies View Related

Ubuntu :: Hp Laserjet Pro M1212nf And Maverick 64bit?

Dec 9, 2010

I've just received my hp laserjet pro m1212nf printer / fax /scanner device. It's installed as a Ethernet printer. First I had troubles with the printer. I could solve it by running

Code:
$ sudo hp-plugin
and then reinstalling the printer from the HP Device manager utility.
During the installation the tool also told me:
Code:
Unable to locate the HPLIP Fax PPD file:
HP-Fax3-hpcups.ppd.gz
Fax setup has been disabled.

[Code]...

View 9 Replies View Related

Ubuntu :: Installation - Getting Laserjet 2100 To Connect ?

Mar 15, 2011

I'm trying to connect Ubuntu (wubi installation on Windows) to an HP LaserJet 2100M printer via a USB cable which worked on Vista (I'm migrating away from Vista into Ubuntu).

System > Administration > Printing..I could not see or add any printer.

I searched around and followed these instructions ..

How to Install HP Printer Driver onto Ubuntu 10.10

[url]

I downloaded hplip-3.11.1.run but in following installation instructions I think I may have needlessly removed a previously installed hplip driver ..3.10.6 .. and various dependencies were loaded with these errors ..

Now when I go to System > Administration > Printing

In troubleshooting there is no connection to CUPS server. The "Add" button is no longer green as before I started dabbling. No discovered printers.

How do I start again to get HP LaserJet 2100M connected (USB cable) .. and printing?

View 1 Replies View Related

Fedora :: HP LaserJet P1007 - Job Submitted But No Prints

Feb 13, 2009

I tried to install HP laserjet P1007 printer in my fedora 8 desktop. I followed these instructions:

yum -y install gcc*
wget -O foo2zjs.tar.gz [URL]
tar zxvf foo2zjs.tar.gz
cd foo2zjs

[root@arnab~]# make
[root@arnab~]# make install
[root@arnab~]# make install-hotplug

$ ./getweb 1005
$ ./getweb 1006
$ ./getweb 1007
$ ./getweb 1008
system-config-printer

Then I found the printer and add it. But the problem is when I tried to try to print a test page, it shows "job1 submitted".....that's all. No page gets printed. If I try once more, it shows "job2 submitted" but again no results. I cant also see all the submitted jobs.

View 2 Replies View Related

Fedora :: How To Install / Share HP LaserJet 1015

Sep 7, 2010

I have installed fedora 12 in my system. And I want to install hp laserjet 1015 printer in my system. or want to share the printer to give the all access printer permission.

View 2 Replies View Related

Hardware :: HP LaserJet 6l And ScenJet 2400 Drivers?

Mar 25, 2010

Where can I find driver and install it on backtrac4 for hp laserjet 6l and scenjet 2400?

View 1 Replies View Related

Hardware :: Hp P1102w Laserjet Does Not Print Through Suse 11.2

Jul 2, 2010

I have a hp p1102w laserjet printer that works in windows. However after connecting it through Suse Linux 11.2 it is recognized and the printer name is showing but there is no driver for the printer. This is a usb connection. I have an 1100a laserjet connected that works but it is a parallel port.

Any suggestions? I haven't been able to find any special drivers on the web.

jim

View 3 Replies View Related

General :: Cannot Install Printer HP-laserjet 1010 On Red Hat El5

Jun 21, 2011

how to install my hp laserjet 1010 printer on red hat el5.when i connect my printer, a new window pops up detecting a new hardware but my printer's name or the driver is not listed. i have the printer's driver cd which is for windows.

View 7 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved