i've recently bought a new set of headphones, since the ones i had were really cheap and only lasted for like 3 months, now i have new ones, not really that good but not as cheap as the old ones xD anyway I've noticed this ones have more bass, therefore the sound is low, is there a way i can adjust this? i know the bass is from the headphones because they sound the same on my window$ machine
View 1 Replies
Ever since upgrading to Karmic, I haven't been able to adjust master volume when my USB headphones are chosen as the output device. If I try to adjust my master volume (via the media keys on my keyboard or gnome-volume-control), the output volume doesn't change until it's entirely muted. I can adjust the master volume fine when I'm outputting through internal audio.I am able to adjust the volume fine on an application-specific basis, but this becomes quite a nuisance, especially when I switch between internal audio (where master volume is regulated) and USB audio (where master volume is always at full-blast). This worked fine in Jaunty, and stopped working once I updated to Karmic. My USB headphones are listed as "Storm HP-USB500 5.1 Headset".
View 1 Replies View RelatedI have a lenovo g555 laptop, about a week old with lucid installed, and whenever i try to play things through the headphones, they come through the speakers as well. I've tried tinkering around in alsa, but the ony two levels are Master and PCM, which seem to adjust both headphones and speakers at once. My audio codec is "Conexant ID 5069"
View 2 Replies View Relatedwhen my headphones are plugged into my computer, the sound comes from both the speakers AND the headphones. I just want the sound from the headphones if they are plugged in.
View 7 Replies View RelatedI'm having an issue with my computer and the headphones. When I plug in the headphones into the headphone jack, the sound plays through the headphones but it also plays through the speakers as well at the same time. I've attempted to play around with the sound settings to see if I can get this issue resolved but I have not been able too. Computer specifications are in my signature.
View 3 Replies View RelatedOk, I have windows and ubuntu, on ubuntu bass is working but on windows it's not, so on windows I listen to music from iPod instead, but is there anyway to fix it. I use iTunes player on windows and the equalizer there wont put the bass on too like it is on ubuntu and iPod.
View 3 Replies View RelatedI'm new to Ubuntu, but have some experience with *NIX (specifically Red Hat and AIX.) I'm not getting any bass out of my 4.1 Logitech THX setup. The surround speakers are operating fine. I know that the bass unit itself is working because I was using it with windows on this computer before I made the switch to Ubuntu. If I run a speaker test from either the sound preferences or the terminal, the speakers work but the bass does not. I ran this command from a terminal to help with the diagnostic effort, but I'm not entirely sure what I'm looking at:
Code:
wget [URL] -O alsa-info.sh && bash alsa-info.sh
Here is the output of the above command: [URL]
I have been searching for an answer to this question for some time now and can't see to find the relevant information anywhere.
I am running Karmic 64bit on a frankenstein desktop. I am using an old Creative Soundblaster card with the live drive front panel. Ever since I started using Karmic I have lost many functions, there are no bass and treble controls, and no other controls other than volume and balance. Am I missing some vital drivers?
View 4 Replies View RelatedWhen I decode an audio clip which contain 5.1 streams (the encoding doesn't matter - or does it?) I cannot find an option which allows redirection of the lower frequencies (from front, back and center channels) to the sub woofer (LFE channel). I understand that this perfectly normal and this is how 5.1 supposed to work. My problem is that my speakers are not full range, so they cannot reproduce the bass in the streams. What I want to know is if there is a way to do something like this: [URL]
Which is described as: Bass redir - Bass redirection. Route basses from all channels to subwoofer. Works only if it is subwoofer at output speakers. Highly recommended for systems with separate subwoofer. Basses are routed before mixing so basses are shown at LFE input level (although 'real' LFE may be absent).
I'm aware of the enable-lfe-remixing = yes option. It works fine for stereo, but not for 5.1
I use ubuntu 9.10 and my pulseaudio version is 0.9.19. The player I use most is SMPlayer (version 0.6.8 (SVN r3213)) and AC3-liba52 for AC3 decoding. My system is up to date.
I installed Ubuntu 10.10 yesterday. I have an audigy2 sound card on my system. But did not see tone control such as bass and treble slide in mixer. When I run alsamixer at terminal window i got these controls but alsamixer does not control my sound card.
View 1 Replies View RelatedI'm having a problem with my sound in the Natty Narwhal version of Ubuntu, where my bass doesn't seem to be working and is coming out as fuzz instead. I don't really know the technical terms for what I'm trying to describe, but instead of the deep part of a piece of music, I get this kind of v sound in the background instead. I get the same problem on headphones or from the speakers, and turning the volume up or down doesn't make any difference. Alsamixer tells me that my card is called HDA Intel, chip ALC272X. I've already tried turning down the PCA volume, as I've seen recommended in other places, but no luck.
View 1 Replies View Relatedsound works just fine, as far as I know it's configured properly, I just don't have all the devices I should have in alsamixer.
[URL]
I got Linux just because I could run ardour. But now that I it I dont know how to use it or make it work at all. I am currently running my recording with a bass pedal that supports recording. I did get a crappy recording on the defalut sound recorder but I dont know what kind of settings I need on Ardour to make it work. The audio codec that the pedal sends as or whatever is PCM2904 Audio Codec Analog Stereo.
View 7 Replies View RelatedI would like your input please. I'm using an HP DV7 laptop and the sound works under Opensuse 11.2 but without base. I have therefore updated ALSA to version 1.0.22.1 to make use of the introduced base switch for DV7 (ALSA changelog here)
I have tried these ALSA options but without any change / improvement to the base sound.
options snd-hda-intel=hp-dv5 and also hp-dv7 and hp_dv7
options snd-hda-intel enable_msi=1
Any ideas?
The second line stops the sound from "stuttering" but the first seem to have no effect.
I need to have some tool to do mixer settings/geo analyser of sound to add bass/treble to the sound output from Ubuntu 10.10.
View 5 Replies View RelatedOS: Ubuntu 10.10 Desktop Edition Computer: Laptop Acer Aspire Timeline X 4820TG Sound Card: don't know (how/where to check?) Software tried: totem, vlc, rhythmbox (does not depend on software) Output: headset and speakers (does not depend on output) The problem: Bass cannot be heard, and "part" of the music plays with a small delay ("offbeat") with respect to the "rest". Note: I have it dual-boot with Windows 7, where the audio works without problems.
this is the first question I post. I hope this information is specific enough,
Recently installed Ubuntu 9.1 following an easy how to. The install session went really well, smooth and only had one little speed bump when deciding which drive to install to (running raid and did not want to loose other partition). Like most speed bumps I got passed it. Ran all the updates then decided to start listening to music with Rythmbox Music Player. The sound coming out of my Klipsch Pro Media 4.1 was muffled and sounded like just the subwoofer was on. I checked all connections and they were fine. I tried looking for equalizer but did not find it and then noticed the sound was like a skipping record. So I looked it up and came across some posts that I could not figure out if they were for my problem. Seemed to me they were just leading me in circles.
[Code]...
I just update the system, and the cpu frequency applet stop working. I can no longer lock the cpu frequency. Once I click the cpu applet icon, The whole applet just freeze right there. Does not matter if what I do with it. Well, at least I hope some one just offer me a bit help on how to lock the cpu frequency in terminal. Other wise I can not run Folding@home due to cooling issue.
Post added at 05:08 AM CST Previous post was Yesterday at 11:58 PM CST Well, it seems like the program take of authentication is mess up. I have the same problem when I tried to config my firewall. In the Firewall case, once I type in my password, the whole window just went blank. For the cpu applet case, nothing happen, the window ask for password does not show up. nothing. The system log did not have any entry...neither does the crash log. Which there are lot of entry there since I install F12
I have just did a fresh install of Ubuntu 10.04 to a computer with a generic, low end, on board graphics card. It will not allow me to change the resolution to something other than 800x600 or lower. 8.04 allowed me to set the resolution to as high as 1600x1200 using the same monitor/graphics card.
View 4 Replies View RelatedI just recently installed Xubuntu 11.04 and I want to adjust the brightness levels. I tried using the corresponding buttons on my laptop, but they aren't working. Where can I find the brightness settings on the OS?
I tried this thread: [URL] , but "Power Manager" didn't have that setting.
i have a 5.1 setup ...
in fedora 10 things were pretty simpler . all i had to do was double click the volume icon and i could change the volume of each of my speakers individually ...
in fedora 11 that was not possible , this adjustment of volume had become more complicated, however there was this "advanced volume control" or something ... i dont quite remember its name , but thanks to that i could still adjust volume of each of my speakers individually ...
in fedora 12 i m not able to find that application - "advanced volume control" ... how do i adjust the volume of my each of my 5.1 speakers in fedora 12 ?
Running F14 on Dell Studio 14 with LCD screen and US keyboard selected. After initial power on the keyboard selection of "Windows Key" + F4 will dim the screen and the "Windows Key" + F5 will brighten the screen. When being used, either combination will also show a meter on the screen to display the adjustment of the brightness. When the lid is closed the computer is set to suspend by default. After the computer is brought back from suspend the keyboard short cuts no longer control the brightness and the meter does not appear on the screen. I have not found any other way to control the brightness and I have to restart to get the keyboard short cuts to work again.
View 5 Replies View RelatedUnder Suse 11.1 & KDE 3.5, when a CD was inserted, the disk was automatically mounted at /media/cd-label. With 11.2 & KDE 4, I get a pop-up from the task bar, from which I must select the CD, and then select the Open With File Manager option. Then (and only then) is the CD mounted at /media/cd-label.Is there a setting that I can change that will eliminate the requirement for all the mouse clicks and just have a CD automatically
View 9 Replies View RelatedHow do I adjust the brightness in Gnome?
View 9 Replies View RelatedI cannot adjust the screen brightness in the power management menu. I can access the window and move the scroll bar, but there is no change.
I am on v 10.04 32bit , a Benq joybook s35.
It was working just fine on the previous version of ubuntu.
I know many apps have their own independent volume controls, but not all do. Is there any way to control this in a similar manner as Windows 7?
View 4 Replies View RelatedOn last boot it was fine but now it is showing 800X600 which is too low . How to adjust it
View 9 Replies View RelatedIf one right-clicks on the date and time tab in Ubuntu 10.10 desktop, then there is no obvious way to change the time. If one right-clicks and goes to help, then the explanation for changing time is as follows under the category 'usage':
2.3. To Adjust the System Date or Time.
To adjust the system date or time that the Clock applet displays, perform the following steps:
1. Right-click on the applet, then choose Adjust Date & Time.
2. Type the root password, then click OK.
3. The Clock applet starts the system tool that sets the system date and time. Use the tool to adjust the date and time.
The actual way to do this is as follows:
Right-click on the date and time applet. select preferences, and down at the bottom of the window that opens push the 'time settings' button.
Then you will be able to adjust that date and time.
I'm having trouble with my mouse wheel. On one click, it pulls down to the halfway point. This leaves me with either dragging the bar around on the right hand side, or using the touch pad. this is a new (to me) notebook, which I haven't had for long. I just can't find where to adjust the sensitivity.
View 1 Replies View RelatedDoes anyone know of a way I can adjust the size of a partition in KDE down to the exact size of the files on it so there is no blank space?
View 4 Replies View Related
