General :: NVidia Nforce Ethernet Card Not Detected In RHEL 5

Jun 8, 2010

I use an nVidia nforce MCP73 ethernet card on Red Hat Enterprise Linux. It is not getting detected and hence I'm unable to configure my network.

View 14 Replies


General :: Ethernet Card Is Not Detected On System RHEL 5.1?

Jun 21, 2010

I install RHEL 5.1 on my system. But my Ethernet card is not detected. I found my Ethernet card is of "ATTANSIC Technology corp L1 Gigabit Ethernet Adapter(rev b0). I already downloaded the driver. Someone tell me step by step process, how to install this driver over RHEL 5.1.

View 2 Replies View Related

CentOS 5 Networking :: NVidia Corporation MCP79 Ethernet Card Not Detected In MAC Mini?

Feb 26, 2010

I have installed trixbox in Intel MAC mini PC, installation completed successfully. After reboot network card was not detected.

My MAC mini PC comes with nVidia Corporation MCP79 Ethernet card. how to enable Ethernet card with out affecting the tribox. trixbox- version comes with Cent OS 5.4. [Moderator edit: s/deducted/detected/]

View 5 Replies View Related

General :: Ethernet Card Not Getting Detected?

Feb 22, 2011

I have installed fedora core 8 on my system. But i am unable to use LAN connection. here are the results of some of the commands which give error messages

[root@localhost ~]# lspci | grep -i ether
00:19.0 Ethernet controller: Intel Corporation Unknown device 10f5 (rev 03)
[root@localhost ~]# uname -a


View 11 Replies View Related

Hardware :: Rhel 6.0 - Detecting Ethernet Card

Mar 23, 2011

I was here yesterday trying to make my ethernet card(which my rhel 6.0 doesn't detect) works. I initially untar a file that has the driver for my card which i got from atheros. When i tried to run it i.e ./ i got the following result:


View 2 Replies View Related

Debian Installation :: No Ethernet Card Detected

Jul 28, 2015

I am installing Linux for the first time right now and I am facing a bit of an issue when it comes to network hardware driver installation. The NIC on my motherboard is a Marvel 88E1111 (computer is very old). During the installation of Debian, I got to a menu which read "No Ethernet card detected. If you know the name of the driver needed by your Ethernet card you can select it from the list", then provides me with said list of driver names.

However, the only driver I could find that came close the NIC I am using was one called just "Marvel", and selecting actually didn't do anything (screen flashes blue and returns me to the same menu). So I continued by selecting the "none of the above" option, and now the new menu reads: "A driver for your hardware is not available. You may need to load drivers from removable media (...)". So I thought I should google for the drivers and see what I can find. The official site of the company that made my NIC doesn't even list my model in their drivers' list (to be expected since it is so old).

Then I found this: URL.., but I was expecting more of a download than the source code itself.

View 2 Replies View Related

Fedora Hardware :: Ethernet Card Not Detected In 14?

May 31, 2011

i have newly bought Desktop system with the following configuration:

1)intel DH67vr mother board with i7 microprocessor inserted
2)1000Gb hdd
3)Dvd Drive
4)Nvidia graphics card -1Gb

i successfully installed Fedora 14 in that machine.though the mother board has inbuilt LAN port,it is not detected by fedora14.

View 4 Replies View Related

Ubuntu Networking :: Ethernet Card Not Getting Detected

Dec 3, 2010

I have brought a new DELL INSPIRON 1410. I installed ubuntu 10.04 but my ethernet card is not getting detected where as in windows 7 is working..

View 2 Replies View Related

Red Hat :: Network Card Is Not Detected By RHEL 5 On Laptop

Nov 1, 2010

I have an Acer Laptop and I am trying to use Linux Redhat 5 on it but for some reason the NIC is not detected by Linux. It is a bit surprising to me that the same problem was seen in my desktop computer but after changing the NIC to a different slot the Linux OS detected the NIC and it is working fine but my laptop still has the same problem.

From troubleshooting point of view:

1. Installed Linux multiple times but it didn't work.
2. Tried to add the hardware (NIC) but it didn't work.

Note: The NIC was working fine when I first installed Linux but after sometime it didn't. The laptop is dual boot (Windows & Linux) when I boot via windows the NIC works fine but not with Linux.

NIC Details:

Device Type: Network Adapter
Manufacturer: Broadcom
Location: PCI bus 2, device 0, function 0

View 4 Replies View Related

Ubuntu Networking :: On-board Ethernet Port Not Detected - Have To Use PCI Card?

Jul 21, 2011

I'm running an ubuntu maverick server, and I'm having a slight problem with networking. I've only got one ethernet line running into my room, and I've got loads of computers. The server has 2 ethernet ports, one integrated into the motherboard, one on a PCI card that I took from my old server. The on board ethernet never worked on my old server- but I only tried it out post-install, it was hooked up to the card during install (For the record, networking on linux has *never* worked for me if I installed then plugged in the networking stuff after the fact). So I just used the card instead. Transferred the hard drive into a new machine, and lo and behold, it would only work after I transferred in the card from the old one. What I wanted to set up is a basic NAT system, where the network connection is routed through from my server to my main desktop- but when I run ifconfig, my card is not detected, just lo and eth0. How can I fix this?

View 3 Replies View Related

Ubuntu :: NForce 2 Sound And Ethernet Drivers ?

Jan 9, 2011

I'm running Ubuntu 10.10 on my brother's computer. He has his sound system connected via the 3.5MM audio connector, but he also has an optical port on the back of the computer we have yet to try (he has cable and all though) but I doubt that will work versus the 3.5MM audio connector. His ethernet also doesn't work, he doesn't need it as he has a Linksys wireless PCI card and that works as of right now.

I also am not sure about his current graphics driver, in Windows XP he could have his native screen resolution which was either 1920x1080 or 1920x1200, I'm not at his place right now so I can't find that out. On Ubuntu he can only go to like 1400x1050 I believe, which isn't nice on his 23" monitor.

View 2 Replies View Related

Red Hat / Fedora :: Ethernet Card Not Detected In Red Hat 5.3 In Dell Inspiron 1525 Laptop

Jun 14, 2010

i have installed red hat 5.1 on my dell inspiron 1525 laptop.It is not detecting any ethernet card.driver is marvel yukon 88E8040So far i found this package to be installed kmod-sk98lin-PAE- but it is showing me the dependencies problems..

View 4 Replies View Related

Ubuntu :: Nvidia Graphics Card Not Detected?

May 8, 2009

I got Linux Ubuntu because my Vista installation messed up, and I couldnt find the recovery CD. Im pretty glad I installed Linux, as it seems really freidnly, and a bit more open that Windows, I must admit. The problem is, I am trying to install my Nvidia GeForce 8600GTS on the system, and it isnt working. It was working fine on Vista before, so it shouldnt be a hardware problem. I have followed various instructions on websites, whioch take me throguh some stuff about stopping GNOME, removing * linux restricted module * and so on. But when I get to the crucial point, with the agreements and installations for Nvidia, it tells me it cant detect any graphics cards.

View 11 Replies View Related

Installation :: Can't Get MCP73 NVidia Ethernet Card To Work In Fedora 10

Dec 7, 2008

I just installed Fedora 10 on a brand new machine with an on-board nvidia MCP73 ethernet card. Now, when I initially boot up the box after installation, the card comes up and gets a DHCP address just fine. When I go to edit the network settings (change to static) the NIC dies. I don't think I have the proper driver. Does anyone know a) where to get the driver and b) how I can install it?


View 3 Replies View Related

CentOS 5 Hardware :: Sound Card Not Detected (nVidia Corporation MCP61)

Jun 13, 2010

how to detected sound card or drivers.when i am trying to detect sound card by using command system-config-soundcard it gives output on gui mode (Audio Configuration) but there is nothing show on PCM device. System Configuration which i am using.

#uname -a
Linux *** 2.6.18-8.el5 #1 SMP Thu Mar 15 19:46:53 EDT 2007 x86_64 x86_64 x86_64 GNU/Linux
00:00.0 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a1)


View 3 Replies View Related

OpenSUSE Install :: NVIDIA NForce 590 SLI Installation Halts?

Dec 8, 2010

I would like to build up a multi boot system with 11.3 on ASUS M2N32 WS motherboard inclusive NVIDIA nForce 590 SLI RAID controller and Marwell 88SE614xSATA connectors.The problem is that if I built up the RAID-1 arrays (2x500, 2x1000) it cannot be seen from Suse install. As far as I investigated the nForce driver is in 11.3, but in this case why the installation hangs (no reset button, only power off). Sorry I cannot provide you a log, becuase the installation procedure goes to the restart, the system restarts, and Grube says error 15 or 21.

View 2 Replies View Related

Ubuntu :: Nvidia GeForce 6150SE NForce W/ Natty?

May 1, 2011

I first started having problems on 10.10 a few days ago. Just boots to a command prompt. After troubleshooting, I found when I remove xorg.conf gnome starts up. Under System>Preferences>Monitors shows my correct Monitor model and resolution.

The resolution displays properly, 1680x1050, but without Nvidia and Graphic acceleration, I can't run my Compiz effects or XBMC. I'm having the exact same issues with 11.04. I ran nvidia-xconfig as root to get an auto gen xorg.conf. No change. GeForce 6150SE nForce 430 integrated graphics card


View 7 Replies View Related

Hardware :: Using Geforce 6150 Nforce 430 And NVidia-drivers 196.*?

Jul 20, 2010

I used the videocard Geforce 6150 nforce 430 (NV4C) without problems untill the upgrade to kernel > 2.6.32 and nvidia-drivers > 190.*. After the upgrade I can use only nv and vesa in the Gentoo x86_64 and in the Fedora 13 x86_64. When I try to install Geforce 8800 GT everything becomes good with free nvidia-drivers and with proprietary ones in both distributions. use this videocard with the kernel 2.6.33(34)* and nvidia-drivers 196.* ?

View 2 Replies View Related

Fedora Hardware :: NVidia Corporation C73 [ GeForce 7100 / NForce 620i ]?

Sep 9, 2010

I am just getting into fedora and have installed it on an EMachine ET 1810. According to my SMOLT info, I have the above Video card. (my smolt info is in my signature). I had installed a couple of games that require 3d drivers in order for the game to play! but I can't find any.

View 3 Replies View Related

OpenSUSE Hardware :: No HDMI Audio On NVidia GeForce / NForce IGPU On Mb ASUS P5N7A-VM 11.2 Or 11.3?

Aug 6, 2010

I have an ASUS P5N7A-VM motherboard and was using Optical out for sound without issues running OpenSuse 11.2. I then got rid of my receiver and wanted to just use HDMI sound. I couldn't get it to work so I upgraded to OpenSuse 11.3. I simply went to the Sound control panel applet and changed it to Internal Audio Digital Stereo (HDMI). I can not get any sound from it on OpenSuse 11.3 either. I have ran sound tests from the command line "speaker-test -Dplug:front -c2 -l5 -twav" which all run without errors, but nothing comes out of the speakers. I have ran the suggestion of one post "" and here are my results: I have also tried the following post which did not resolve the problem since it seems to be Ubuntu based. I have undid everything from the post as well to make sure I don't stray to far from normal.

[HOWTO] HDMI audio on nVidia GeForce/nForce iGPU - XBMC Community Forum

View 9 Replies View Related

General :: Atheros AR8132 Ethernet Not Detected In BIOS Or Ubuntu On Acer Aspire One D250?

Jan 14, 2010


leopard@brokenbox:~$ lspci | grep Ethernet
01:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)


leopard@brokenbox:~$ ethtool -i eth0

Cannot get driver information: No such device


leopard@brokenbox:~$ ifconfig -a
lo Link encap:Local Loopback
inet addr: Mask:
inet6 addr: ::1/128 Scope:Host


I have had this issue before, and fixed it by booting into Windows XP SP3 and pressing and holding the power button down until the computer shuts down. (e.g. "Unclean or "Illegal" or "Cold" boot.) Unfortunately, not having Windows XP SP3 on my system anymore, I have to do this in Ubuntu. I have tried several times, and it is clearly not working. I don't want to try too many times more for fear of damaging my ext4 file system.

I looked for this issue on Google and found only driver problems, not device problems. There is no Ethernet option in the BIOS, except for the Network Boot, which should always show the device whether its in use or not. Is it silly to ask if Windows in a VM in an unclean shutdown may solve the problem? The driver for the device is currently supported by the kernel out of the box:


Linux brokenbox 2.6.31-17-generic #54-Ubuntu SMP Thu Dec 10 16:20:31 UTC 2009 i686 GNU/Linux

It uses/used the atl1c driver. It was working on the same install just about a day ago!

View 9 Replies View Related

Ubuntu :: Share Internet From 1st Ethernet AND To 2nd Ethernet And Wifi Card?

Feb 8, 2011

I am basically wanting to use my Ubuntu 10.10 computer as a router. Note: Before you say just get a router please note that I am poor/cheap. I have two ethernet connections and one wireless connection on my netbook. I want to share the internet connection that is going into one of the ethernet cards through the other ethernet card and the wireless card.

DSL-->1sr Eth --> 2nd Eth (currently works)
DSL-->1sr Eth --> Wireless Card (Adhoc) <--(connects with limited connectivity AKA no internet)

The 2nd Ethernet card already has working internet, but when I connect to the Wireless card (through an Adhoc network), it cannot get an IP (I believe).

View 2 Replies View Related

General :: Only One GPU Detected In The Nvidia Quadro NVS 450

Jan 11, 2011

I just built myself an new workstation and now only 2 of 3 monitors are working. I built the nvidia driver by downloading it and installing with ./Nvidia...Before when I ran nvidia-settings I saw two GPUs listed but now I only see one. Xorg Config (Not sure how I ended up with 3 devices in there):

# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:39 PDT 2010
Section "ServerLayout"
# Removed Option "Xinerama" "1"


View 1 Replies View Related

General :: Sound Card Not Detected?

Jan 5, 2010

Hardware : Intel atom (COM)Audio - ALC 888OS : Ubuntu 9.04Observation : Sound Card not getting detected.-> I downloaded High Def. Audio Codec as "LinuxPkg_5.13rc9.tar.bz2" from RealTek site, compiled and installed the drivers.-> But while installation I got a GUI saying "No PnP or PCI audio card detected".-> lspci command shows all other pci connected devics except sound card(ALC888).->I tried recompilation of Linux kernel to make HDA Codec as a Built-in modules (built-in ALSA driver support) ,but still there was no change in behaviour.

View 5 Replies View Related

General :: Assign IP Address To 2nd Ethernet Card?

Jun 22, 2010

In my red hat Linux machine there was a Lan card using eth0. IP is asign to that network card and it is functioning properly. I add another ethernet card in my linux machineit was detacted and when i use the commandQuote:[root@localhost root] # ifconfig -ait show me both eth0 and eth1 lan cards.I can see Ip address in my eth1 ethernet card but When I enter into

[root@localhost root] # cd /etc/sysconfig/network-scripts
and i use ls command it only show me the file ifcfg-eth1 and with


View 8 Replies View Related

General :: Card Is Detected But No Sound Is Produced

May 16, 2010

hello experts! i have a problem with my sound card (Creative SB X-Fi Xtreme Audio), Got the driver from Creative site. The problem is that the card is detected but no sound is produced, it's not muted, i already checked. also tried the latest pulseaudio but nothing seem to work. what could be the problem?

View 2 Replies View Related

General :: Ping Two Ethernet Card On The Same Computer And On The Same Subnet

Jul 6, 2011

I have two NIC Ethernet card (eth1 and eth2) on the same computer (linux) connected by a cross cable.

The two interfaces are on the same subnet :

eth1 :
eth2 :

Then i add a route for each interface :

route add -net netmask eth1
route add -net netmask eth2

Finally,i'm trying to ping :

ping -I eth2 or ping -I eth1

Ping command reaches error : Destination Host Unreachable

View 2 Replies View Related

General :: How To Call Ethernet Card - By Device Name Or Nick Name ?

Jun 23, 2010

I want to know that in my Linux box under "Network Configuration....>Devices" i can see Device eth1 and Nickname eth0.

The ambiguity in my mind is when we want to down network interface we should call it by device name or nick name




View 4 Replies View Related

General :: Pulseaudio / ATI Technologies Inc RV710/730 No Card Detected

Jan 18, 2011

I have installed arch linux and try to do pulseaudio according to wiki. But pulseaudio doesn't detect my sound card. I don't have alsa installed. I run


pacmd list

and it shows that no card is available. Commands


$ fuser -v /dev/snd/*
$ fuser -v /dev/dsp

View 3 Replies View Related

General :: VMWare SuSe - Cannot Ping Switch (Ethernet Card)

Aug 23, 2010

I have linux suse installed on VMware, my pc is running Windows XP. I have a switch connected to my ethernet card (also through console cable). When I am on windows I can ping the switch, but from linux I can't. My ethcard is "Bridged" on VMware, I can ping

View 14 Replies View Related

Copyrights 2005-15, All rights reserved