General :: Wireless Not Working - Ndiswrapper And Drivers Installed?
Sep 15, 2010
I just recently put Ubuntu 10.04 Lucid Lynx on my laptop with windows dual booting. I'm pretty new to all this stuff, so I'm a bit confused. I followed instructions I read on here, but none of it seems to be working. I put all of the 3 Ndiswrapper things on, and then copied the .inf and .sys files from windows into the same directory. I just want to connect to my home network, which has WEP security.
View 14 Replies
ADVERTISEMENT
Feb 15, 2010
I just installed ndiswrapper so I could install my wireless PCI card drivers.I did that and it is recognized and so is the network I want to connect to.But for some reason, it just wont connect. It will spend a long time trying to connect, but then just says "disconnected".What could be the problem? It's not like I have a bad connection or anything
View 2 Replies
View Related
Mar 30, 2011
Before I start off, I must say that I know NOTHING about Ubuntu. I only know how to run .deb files. So I installed my wireless driver via the graphical ndiswrapper (FYI my wireless adapter is a Proxim 8424-WD). It then said "Unable to see if hardware is present". After I exited out of that message, it said "Hardware:Present" (or something of that sort) next to the newly installed driver. I tried searching for wireless networks and found none. I'm guessing something didn't work right. I used this command "lshw -C network" and got the following result.
[Code]...
View 9 Replies
View Related
Dec 18, 2010
I have a problem installing mi dlink dlw-g122 wireless usb adapter.I installed the drivers, in fact when executing
ndiswrapper -l
the output is
dr71wu driver present, hardware present
but when I try to execute
modprobe ndiswrapper
I have this error:
FATAL : Error inserting ndiswrapper (/lib/modules/2.6.12.9-386/kernel/drivers/net/ndiswrapper/ndiswrapper.ko): Operation not permetted
View 4 Replies
View Related
Mar 18, 2011
I've been using a RealTek 8190 PCI wireless card on my desktop in Ubuntu 10.04. The net819xp driver worked fine in ndiswrapper. Then my housemates got a new router and switched our wireless SSID & password. In network manager, I can see the SSIDs, but when I try to connect to our SSID, it continues trying to connect but never does connect. Something related to the router change and router firmware upgrade created this problem and i'm sure i need to fix it on my computer. All my windows7 flatmates are connecting with no problem. Right now I'm using my laptop, so i can't copy & paste results from terminal commands,
View 1 Replies
View Related
Nov 21, 2010
how to use the Sitecom WL-324 usb stick with ubuntu (10.10)? (It works with windows.)
lsusb | grep Ralink
Code:
Bus 002 Device 004: ID 148f:2878 Ralink Technology, Corp.Im using Ubuntu 10.10 x64 with a Phenom(tm) II X6 System My results so far:
sudo modprobe rt2870sta (or rt2800usb)
result (rt2870sta) :
lsmod | grep rt28
Code:
rt2870sta 445182 0
crc_ccitt 1699 1 rt2870sta
dmesg
[code]....
View 9 Replies
View Related
Mar 18, 2011
With nearly all Linux distributions (Ubuntu, Kubuntu, and Linux Mint being the exceptions), my system never seems to recognize that my laptop even has a wireless card attached to it. That is, when I run "lspci" the wireless card doesn't even show up on the list like it does with Ubuntu/Kubuntu/Mint. This narrows my options when it comes to choosing a distro to install on my computer. I can't seem to find instructions as to how I can make my wireless card work. I assume it needs a driver. I managed to find the driver, I think, in the form of a .tar.gz file. The card is a Realtek Semiconductor, RTL 8191SEvB Wireless Lan Controller (rev 10).
View 1 Replies
View Related
Jun 27, 2010
I've installed Ubuntu Netbook 10.04 on my HP DV2000 laptop and now I want to get my wireless to work by installing the proprietary broadcom drivers (4311, I think). But my internet doesn't work yet obviously, so I need to download the drivers to my thumb drive on my desktop and install them on my non-networked laptop.My issue is that I don't know:a) Where to get the driversb) How to install them from a local drive
View 2 Replies
View Related
Apr 6, 2010
I have a problem with the fritz!wlan usb stick. I have installed itth success on another PC by using instructions published here Ndiswrapper - openSUSE.Today I have decided to erase WindowsXP from my wife's computer (that is an identical to the one I use). So I have downloaded the OpenSuse 11.2 DVD and I have performed a completely new installation from DVD.After installation has been executed with success, I have decided to install an internet connection using the istructions above. I told to myself: "it will take 5 minutes, all I must to do is to reply action I have done one month ago... the internet usb-stick is the same, so it will be easy to replicate the process..."I was wrong... When I reach the point where I must "modprobe" the ndiswrapper module I receive what follows:
Code:
linux-2n4g:/home/mila/Desktop # modprobe ndiswrapper
WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in
[code]...
View 7 Replies
View Related
Jan 13, 2011
I have installed Fedora 14 on my new laptop Thinkpad T410 but the wireless card is not detected.
I tried to install the drivers but got error. How to install the driver.
[root@sheril sheril]# lspci
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02)
00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) .....
View 1 Replies
View Related
Feb 18, 2010
I'm having problems getting the wifi to work on my toshiba satellite pro l40 (psl4be). My laptop has a wifi card built in but linux cant seem to be able to find it. I tryed following these instructions and i got this output:
Code:
james@james-laptop:~$ lsusb
Bus 007 Device 001: ID 0000:0000
Bus 006 Device 002: ID 0bda:8197 Realtek Semiconductor Corp.
Bus 006 Device 001: ID 0000:0000
[Code]...
as you can see its telling me i have no wifi card, even though i am fully aware i do. ive tryed using ndiswrapper to install the windows drivers of the ethernet adaptor but my wifi still doesnt work, im guessing ethernet has nothing to do with wifi.I intend to convert from windows, however if i cant get the wifi to work i can only see linux at a major disadvantage as i use my wifi alot.
View 9 Replies
View Related
Jul 3, 2010
I have a Broadcom B4312(I believe) wireless card and installed the drivers for it, but under the Wireless tab in Network Connections, it doesn't show "wlan0" or anything similar to "eth0"(which it shows under "Wired"). I ran iwconfig and this is what I got:
[Code]....
View 9 Replies
View Related
Jan 17, 2010
I'm dualbooting XP and Ubuntu. I've probably switched back and forth over 50 times today to download certain files to hopefully get this thing working. Problem: I use a Linksys Wireless-G Adapter to connect to my wireless router. The cord is too short to reach my PC. Different rooms. Ubuntu will not connect without the correct drivers. I have installed ndiswrapper and the ndisgtk.
Adapter Model No.: WUSB54GC
ver.: 3.0.02 / 3410-00450
I have successfully installed the following programs without internet:
1) Wine v. 1.1.36
2) ndiswrapper
3) ndisgtk
I have access to the specific driver on the installation CD for the adapter.Questions: 1)How do I use the NDISwrapper or ndisgtk to use the drivers from the CD? 2)Where do I move the drivers if I have to in order for ubuntu to use them?
View 9 Replies
View Related
Oct 17, 2010
Is there some program out for linux that is similar to ndiswrapper, in the sense that it can use Windows drivers for printers? As of right now, printing has been one of those issues I've had in linux for years, but I was lucky enough to have a supported printer. On other machines, including family members, they are not so lucky enough to have a supported printer.
View 2 Replies
View Related
Dec 31, 2010
i have ubuntu 7.04 and i have wireless driverAtheros Hardware Access Layer (HAL)but i cant get it to work in restricted drivers it's checked as enabled but status is not in use how do i fix this
View 9 Replies
View Related
Jun 2, 2010
I am new to fedora linux. I want to know how to install wireless driver for my Dell Wireless Dell Wireless 1397 802.11b/g Half Mini Card. I am using fedora 13. Below is my lspci command outuput.
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03)
00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 03)
00:1c.5 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 6 (rev 03) .....
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3)
00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 03)
00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03)
03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05)
03:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22)
03:01.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12)
03:01.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12)
09:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe (rev 10)
0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)
View 11 Replies
View Related
Dec 31, 2010
I have lenovo thinkpad, T61 with Intel 4965AGN wireless card. It is a N card, it works under N mode in windwos, but not in Ubuntu (10.10). I installed ndiswrapper and got the windows xp drivers for this card. the issue is that i got an error when installing the drivers and since then I cannot use wireless.
The error i got is: Code: Module could not be loaded. Error was: FATAL: Could not read '/lib/modules/2.6.35-24-generic/kernel/ubuntu/ndiswrapper/ndiswrapper.ko': No such file or director I unistalled the driver, but now under network connections no wireless connections appear, nothing. I cannot use wirless anymore.
View 9 Replies
View Related
Nov 12, 2010
According to a help page (Wireless Network Card Installation - openSUSE) I need to use ndiswrapper to install the windows driver for my wireless. However it appears the command 'ndiswrapper' was not installed with the operating system. How can I obtain the package for ndiswrapper and install it? Not being connected to the wifi makes this step tricky
View 1 Replies
View Related
Mar 20, 2011
I recently upgraded to OpenSUSE 11.4 GNOME on my ancient Compaq Armada E500 (Pentium II processor w/512MB of RAM) and now I'm trying to install my wireless driver with ndiswrapper. I've done this a couple of times before, but I'm having trouble getting ndiswrapper to find my driver. The driver is located in a folder on my desktop, but when I type the command 'ndiswrapper -i home/edwin/Desktop/WPC54G_40826/LSTINDS.INF' I get a message that there is no such file or directory at ndiswrapper's location, which is usr/sbin/ndiswrapper. So how do I get ndiswrapper either to look in the directory where the file is located or get a copy of LSTINDS.INF into the usr/sbin/ directory, which must be accessed as root?
View 9 Replies
View Related
Jan 5, 2010
I recently received a used laptop that I was going to use for my kids, a Compaq Presario 2100. Everything went fine on the install, however I could not get the WiFi to work. The internal card, a Broadcom BCM4306, was attempting to use the b43legacy drivers, which I understand to be the native driver for this card, but would get all sorts of strange errors in 'dmesg', and would never get a solid connection.
After fiddling with this for 2 days, and reading countless troubleshooting guides, I finally gave up and decided to get it working with ndiswrapper. Everything worked perfect, except I can only get it to work if I first load b43legacy, then load ndiswrapper, then unload b43legacy. If I blacklist b43legacy, and just load ndiswrapper, iwconfig does not report a wlan0.
I ran across this posting, and decided to try this, but it also did not work. Plus, with this file in place, any attempt to use modprobe would complain about every line of that file.
View 3 Replies
View Related
Dec 11, 2010
I'm trying to get a Belkin f5d8010 working. I installed ndiswrapper from Add/Remove software, but when it was done, I couldn't find it. Checking the forum, I ran across something saying that I had to compile from source. This is in Fedora 13. Can I get it working with "point-and-click," or do I have do something that requires some thought?( I don't have many of those.)
View 14 Replies
View Related
Jul 31, 2010
I just installed ubuntu on my hp desktop that has wireless built in. I finally found the windows inf and sys driver files, and learned how to get ndiswrapper without internet and installed the driver. It says that i have the hardware it controls, but when I look at the connection icon, it says not connected, has lost the wireless connection block, and I am not connected to the internet. The wireless is called USB Wireless 802.11 b/g , but it is not usb and is plugged straight into the motherboard with the only physical part is the antenna. Why can't I connect?
View 9 Replies
View Related
Nov 29, 2010
I installed openSuSE 11.2 sometime ago in a COMPAQ Presario CQ60-419WM laptop (the ones that Wal-mart sold for $300 about a year-and-a-half ago. I installed the 64-bit version because I saw that the processor could support that (perhaps that was not a good idea). I have some problems that seem related to not having the necessary drivers. My wireless has never worked and my display is far from what I would like it to be (the response is slow, if a drag a window, its motion is jerky, if I scroll down in a browser window, the motion is wavy). The look and feel is very different from what I get at work and I do not know how to fix it.
[code]...
View 3 Replies
View Related
Jan 10, 2010
I've bought an RALINK getnet Wireless USB adapter and am trying to get it to work on a dual boot pc running XP and 9.10. According to the forums and the manufacturers website (www.getnet.com.tw), this should be supported in Linux.
Using the disk that came with it, I have gotten it to work in Windows. I've spent nearly a day scouring the Ubuntu forums and trying different things, but still haven't got it working in 9.10. (I think that most of my confusion is that many of the threads are for earlier versions)
If I type "iwconfig", I get this:
Code:
graeme@graeme-desktop:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
[Code].....
I have the CD that has a LINUX directory, but am not sure what to do with it. Through other threads I have determined that my drivers are rt2870.sys and .inf and have downloaded these. I'm not really sure what to do with them next..... Many threads talk about going System>Administration>Networking, but I don't have this as an option. I have however got an option which I downloaded called "Windows Wireless Drivers" which seemed to let me load the rt2870.inf driver, but then says "No" after it (not very helpful).
I have enabled Wireless Networking, and added my SSID etc etc, but I still don't connect.
View 6 Replies
View Related
Mar 22, 2010
I've got something that's really confusing me. I'm a total noob, but I read a fair bit about Ubuntu before I overwrote my windows. To make sure it worked, I used the Live run option, and it worked fine on my system. Everything worked, it notified me, however, to use the internet I'd have to download proprietary drivers (Broadcom B43 wireless driver and Broadcom STA wireless driver). I did it and my internet started working. So everything was fine and I rebooted and actually installed the OS. Once installed, it would not get internet, nor prompt for drivers being required. So I checked my manual and tried to do it manually: System / Administration / Hardware Drivers. It searched, and said there were no proprietary drivers. I thought that this was weird, so I rebooted my system "Live" again (even though it was already installed): and the Drivers were there again! They only show up in live, I can't get internet in the installed version. What's going on? How do I get these two drivers to show up on my actual installed copy, not my lie copy?
View 3 Replies
View Related
Jun 4, 2010
I have a Dell Vostro 1500 that has a Broadcom BCM4312 wireless card installed. I do not have access to a wired connection to the web so any thing I have to install is a download on my windows machine and then transfer that to the debian machine. I just finished installing Debian Squeeze but can not get my wireless card to scan for any networks. I found a tutorial at [URL] and followed the steps there. Finding all the dependances and installing them one by one (took me all day). My wireless card still will not scan for networks. After doing a 'sudo ifconfig eth1 up' it still will not scan for networks.
Output from ifconfig:
raygo75@RayGo-2:~$ sudo ifconfig
eth1
Link encap:Ethernet HWaddr 00:16:44:9b:e9:cc
inet6 addr: fe80::216:44ff:fe9b:e9cc/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:17 Base address:0xc000
lo
Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:28 errors:0 dropped:0 overruns:0 frame:0
TX packets:28 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1900 (1.8 KiB) TX bytes:1900 (1.8 KiB) .....
How do I get around this? It wants to get something from [URL] and I do not have internet access. It looks to me like it just wants to download the wl dirver, again, which I have done in the previous instructions I found. I am a retired UNIX (hp-unix) administrator so I know my way around the system.
View 14 Replies
View Related
Oct 17, 2010
Iv just installed 10.10 but my wireless doesnt seem to be working.Iv checked that the physical switch is on at boot (since that used to be a problem with previous releases) but to no avail.
View 3 Replies
View Related
Apr 12, 2011
I have installed the madwifi drivers and I am able to put the wireless device into monitor mode using airmon, so that tells me that the driver is working and the device can be picked up...
But I still can't connect using Wicd and I really don't know what to do next
View 14 Replies
View Related
Mar 20, 2011
I have a Realtek RTL8187SE wireless card that out of the box will only connect to Open Wireless Networks. I need to know how (and if) I can install NDISwrapper in OpenSuse 11.4 (KDE), anytime I have ever used a KDE distro, it seemed NDISwrapper didn't work I want to give OpenSuse a shot, but this is one of the things holding me back. I'm am currently posting from the LiveCD and it's very nice! I will be able to do a full install!
View 9 Replies
View Related
Oct 8, 2010
I wanted to try 3d desktop so i installed 3d support for nvidia graphics using the instructions on this webpage [url]
I Dont have nvidia i have ati so needless to say i have to gui when i boot up
It shows the fedora loading bubble then a blinking cursor.
I can get to a virtual terminal.
So how do i undo what i did I just want to get it back to normal i dont need 3d support.
View 3 Replies
View Related
