Gonna try and switch to a lixun distro.... but want to make sure I can still do these:TorrentingInternetTether with my droid to be abel to play PS3Also my wife loves little games like cards, bejewled etc.. I heard linux has a lot of free games?
View 2 RepliesI was trying to connect my android phone just to send some AT commands using Minicom or Seyon. But I was not able to connect it. I have connected my phone using a USB cable.Do I need to connect my phone through the serial cable by using a minicom connector to be able to send the commands to the phone.Also when I launch it says Initializing Modem...thenModem at /dev/ttyS0 is available. If I try to Dial it says Warning related to the Baud rate.But After that I am not able to do anything.
View 7 Replies View RelatedWhen I first got my BlackBerry, USCellular said I couldn't tether with Linux. That's not so, all you need is BlueTooth (USB adapter, built in, whatever)
You just install Blueman
Code:
sudo apt-get install blueman
Search for your BlackBerry, Pair it to your computer, then go to Devices > Serial ports > Dial Up Networking.
Your wireless connection should be in Network Manager. NOTE: You may have to right-click on NM and setup Numbers, Passwords, Usernames. I did.
I have upgraded to 10.10 and have lost all ability to tether my iPhone via USB or Bluetooth on my Gateway LT24 series Netbook. I'm using an ASUS Bluetooth USB dongle. Here is the output I get to see the status of my connection:
markvv@netbook:~$ dmesg | tail -n10
[ 48.239050] cfg80211: Regulatory domain: 98
[ 48.239056] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[Code].....
In Blueman, I have my Bluetooth setup as a Network Access Point, dnsmasq enabled. PAN and DUN support are set to NetworkManager. I cannot change these to Blueman (not sure if I should be able to).
I really need my tethering feature to work. Or, should I revert back to 10.04.
What do I need to tether my phone with Ubuntu? I've tried using Berry4All but there's no conf file for my carrier, and I don't know how to create one.I have my carrier's APN and the number to dial, other than that do I need any extra info? Is there another software that I can use to tether my BB?
View 5 Replies View RelatedCan anyone tell me how to rip a DVD so that it will play properly on a droid X?
View 3 Replies View RelatedI recently found how to ssh into my ubuntu system with my droid, but I can't seemed to do it the other way around, even if my droid is running off my wireless with the same ip (maybe that's the problem?).
View 1 Replies View RelatedI'm trying to tether my sprint samsung exclaim. I've tried the ubuntu network-manager and gnome-ppp. dmesg seems to show the phone connected and the cdc_acm driver loading the phone as /dev/ttyACM0 . However running wvdialconf says no modem detected.Furthermore, when I specify the device in gnome-ppp I get an input/output error.how to get tethering to work in 9.04?
View 1 Replies View RelatedI have a 9.10 installed on my USB stick drive and I am trying to get my iPhone to tether with bluetooth. I followed a guide, (installed blueman, connected to phone, enabled tethering, set to trust device and provide network access). The computer connects to the network and says it is successful, and the iPhone has the blue flashing banner saying it is now tethering, but firefox doesn't connect to the internet.
Is there a way to force it to use the new tethered connection?
ya wondering how would I go about this. my phone can do it but nokia says i need to have Nokia pc suite.exe to work.
View 9 Replies View Relatedfirst thing first - started using Linux for the first time yesterday (LONG time windows person) and I'm enjoying it very well, so if I do manage to get any help can it be in noob-language? and when i say that I mean absolutely dumbed down as mch as possible.
I just now figured out how to get terminal open.
now my current internet situation is very weird, my only choice at the moment is to connect my windows 7 laptop to my 10.04 Ubuntu desktop via ethernet cord. Before when i had both win7 on both machines it worked out perfectly with ICS and had no problems, but now with linux it doesnt work at all.
I can sync my Motorola Droid using the USB cable without any problems but I don't always have the USB cable with me and I haven't been able to sync my Droid using bluetooth. My laptop can see the Droid and the Droid can see my computer but it says on my Droid "Paired but not connected". All I want to do is send files back and forth (tethering would be nice but I don't really need to be able to do that).
I can now (I'm really not sure why) send files from my laptop running Ubuntu 9.10 to my Droid but I can't send files from my Droid to my Laptop. Also when I try to "Browse file on device" I don't see any devices even when I select phone as device type.
I've tried what seems to be the best music software. Banshee and Amarok seem to be the most popular and I can't get either to sync. Banshee doesn't do it properly, it "syncs" but roughly 1/3 of the songs don't show up. I believe this to be due to the Amazonmp3 folder which I did move everything out of. Next I tried Amarok. I guess it's a bad case of user error because I can't even figure out how to sync it at all. All I know of right now is to manually create the m3u file in gedit. 11.4 btw and it's a droidX
View 1 Replies View RelatedI'm trying to figure out how to convert .ogv video files to put on my moto droid. Has anyone did this? How??
View 1 Replies View RelatedI'm new to android app development (but not to java) and I want to transfer apps I create on ubuntu to my HTC Incredible mobile phone. My computer's a desktop, so I don't have anything fancy like a bluetooth (unless you recommend I buy a USB one for this). What is the best way to transfer apps to my droid?
I tried using USB, but for some reason neither Ubuntu nor my droid sees the other. It doesn't even charge when I connect it via USB.
if anyone here could recommend a cellphone. My main requirement is that it should tether as a 3.5g modem via USB to a PC running Fedora 13. I have previously used a Nokia to good effect, but their standpoint on privacy is making me look for a different brand.
View 11 Replies View RelatedI was trying to install the android sdk so I can write some apps and play around on a new droid phone i hope to get tomorrow. I had 64bit FC11 installed but the android stuff is only 32bit. I needed to install a bunch of the 32bit libs to get this to work. I installed FC11 64 bit. This cuased problems because the android stuff is 32bit. I couldn't get it to launch so I had to install the 32 bit libraries as well. A lot of the libraries could be removed but I think they will be helpful and useful in other stuff as well.
After installing these just follow the normal android install. I had another problem with the android install because the Ganymede Update Site was not checked so it wouldn't download the updates for the eclipse software. In the Software Updates and Addons window click Manage Sites, check Ganymede Update Site. Here is the link if you have to add it.[URL]..# instruction to get 32 bit android stuff in 64 bit FC11 Add an "rpm" Macro. You'll need this later or it will be hard to tell your rpm versions apart.
Add the following line to the "/etc/rpm/macros" file:
%_query_all_fmt %%{name}-%%{version}-%%{release}.%%{arch}
Code:
[stoggy@localhost][~]
[10:13 AM]$: echo "%_query_all_fmt %%{name}-%%{version}-%%{release}.%%{arch}" | sudo tee -a /etc/rpm/macros
%_query_all_fmt %%{name}-%%{version}-%%{release}.%%{arch}
[Code]...
I have an SSH server running on my netbook on port 2222 and a VNC server running on 5901. The router only has port 2222 open to the laptop.
I use Connectbot on the Droid to connect t my Ubuntu via 2222 with a local port forward enabled 5901 to 192.168.1.111 (laptop IP) port 5901.
Once the conenction is established, I use VNC viewer on the Droid and have it go to 127.0.0.1 port 5901 (to be forwarded by Connectbot over the SSH pipe).
I want to take it a step further. I want to administer my DGL-4500 router without having to remote control the laptop and open firefox. My router doesn't allow SSH.
An obvious solution (in my small mind) would be to install a simple web server process on say port 8080 and do a port forward on the phone to 8080. Then whenever that port is hit, I would want some process that would take the request and pop that person over to 192.168.1.1...
Any ideas on how I could do this OR a better idea on how to do it better without opening the router to the outside world?
I am theorizing I could do a VPN server instead and then find a VPN app. With a VPN, I am theorizing once again I owuld assume an IP address in my home network and then just type 192.168.1.1 on my phone and connect in that way?
I recently installed Ubuntu 10.10. I wanted to setup my droid incredible as a modem to connect via the builtin broadband connection under network manager. I searched around and found couple of ways using wvdial as well as a tunneling app. The funny thing is, that I was able to setup my phone as a usbserial device and use it ONCE to connect successfully via the built-in broadband connection setup method. But ever since, it has not worked . Currently I am running a fresh install of 10.10, and have tried to insert usbserial module for my phone in the kernel, but it does not work. The command I used :
Code:
sudo modprobe usbserial vendor=0x00b4 product=0x0ffb I have not made this change permanent though. But whenever I run this and connect my phone with broadband connect enabled, it recognizes my phone however it uses a 'generic' driver according to the logs, and it never lets me enable Broadband Connection or connect successfully.
Linux for starters, have used this link to help set up the phones tethering using wired cable the computer is old with no wireless and it is integrated into the motherboard so dont flame about spending 20 bucks on a wireless card please. Now, we can start tunneling betwwen your computer and your phone. Change directory to the tools subdirectory of the extracted Android SDK directory. Issue the command ./adb forward tcp:8080 tcp:8080... everything went smooth until here ... there doesnt appear to be a filenamed ./adb so i cant move on and dont know where to go from here.
it is worth noting i am a noob to android sdk and i think i need to set somemore up to get it to work right you download a starter package and the rest you reach out and grab with the starter package although i dont know where tostart there either.
World of Warcraft requires that TCP Ports 1119, 1120 and 3724 are forwarded. The Blizzard Downloader requires that TCP ports 3724, 1119, 4000, 6112, 6113 and 6114 are forwarded. It can also benefit from having ports 6881 through 6999 forwarded. The World of Warcraft Voice Chat feature uses UDP Port 3724.
i use the hotspot feature to play warcraft and i am running ubuntu 10.10 ... i need to forward these ports ... any way to easily download an app to configure the phone like you would a router? its probably easy i just cant find it.
Sony Vaio X upgraded to 11.04 with 2.6.38-8-generic i686 which improved some features but which introduced a serious WiFi problem: while other WiFi works well, connecting via my Droid hotpsot fails consistently despite reboots of everything and renaming of SSID. Another laptop running 10.04 still works fine with the Droid hotspot. One hint: upon upgrading, there was the warning that the laptop hardware did not support Unity and I always get the classic Gnome display.The Droid hotspot shows up in the list of SSIDs but attempts to connect always fail, even when it is made totally unsecured.
Atheros AR9285 Wireless Network Adapter
Qualcom Sony Gobi 2000 Wireless Modem
ifconfig shows no packets with wlan0 or any connectivity.
iwconfig shows correct SSID and other info.
[code]....
im trying to be able to tether my android cell phone to my fedora 13 to use as a router/modem i have gotten it to work on a friends Ubuntu OS i used the app easy-tether but it will work not on fedora
View 11 Replies View RelatedI recently updated my kernel and now can no longer tether my iphone to my openSUSE11.3(x64) laptop. Before the update I could tether.Same machine dual boots to Win7-64bit and can tether just fine.I re-installed the libimobile packages, but my linux no longer recognizes the iphone as a network device.t DOES pop-up some boxes asking if I want to play the media, or view the photos on the iPhone - so that part is working
View 1 Replies View Relatedjust finished installing Ubuntu to my dell mini 10v netbook. I really like it so far but I have hit a problem that may be a potential deal breaker. I have a CDMA HTC Hero phone that I have rooted. I installed the "wireless tether for root users" app on my phone and use it ALL the time to go online on my netbook through my phone on windows. However Ubuntu 9.10 does not seem to connect to my phone running this app. It sees the SSID, and i tell it to connect, and then I just get that circle thing for a couple of minutes then it gives up and connects to my main router if its in range.
View 3 Replies View RelatedThis is on Lucid, using a Dell Mini. I installed the required packages for a USB tether to my iPhone. Network Manager recognized it immediately as wwan0, but it doesn't connect. Also, it never asks me for the password to connect to the Personal Hotspot (as it does when I can connect from Windows).
View 3 Replies View RelatedI just got my Incredible running, and wanted to tether my laptop to it. Is there anything like PDANet that runs in Ubuntu?
View 9 Replies View RelatedIs there any software that can do that? I would hate to have to run the android emulator software and run remotedroid on it.... so many wasted resources for a simple program. Any one know of an app that would let me do this that is made for linux? (specifically ubuntu)?
View 5 Replies View RelatedI'm using Rhythmbox to manage my music collection. I have ripped my CDs into FLAC files. I'm using the Motorola Milestone (The Droid) as my music player and syncing it using Rhythmbox.
Now, when I transfer my music files from Rhythmbox to the Milestone, it automatically convert the FLAC files to MP3. But the conversion is set to 128Kps.
How do I change this default conversion rate? Or even, how do I change to another conversion format altogether?
I'm having the issue that I cannot conenct to the wlan of my Motorola Milestone/Droid with Android 2.2 and the 3G Hotspot service started. When I want to connect, I have to type the WPA2 passhrase in, I do that correctly and then the system tries to conenct. This failed and then I have to type the passphrase again.It's a Samsung N130 Netbook with Ubuntu 11.04 installed.
[Code]...