Fedora Networking :: WMP54G PCI Card Works With FC9 But Not After Upgrade
Jan 24, 2009
I have a now pretty old PC, I think it is 400 Mhz Pentium II, on which I installed a Linksys WMP54G 802.11g PCI card, and on which I wanted to run Fedora 10, but I can't get the wlan card working. As I had a vague memory of having it seen working before, I reverted to Fedora 9, and it worked, at least before I made an update of it. So I took a closer look at it, and besides finding out that there is nothing wrong with my PC and the WLAN card, I also found some oddities. My feeling is that the configuration settings in Network Configuration window seems a bit unrelated to the behavior of the system. Here is a summary of what I found:
1) The WMP54G/RaLink does neither work rightly after installation of Fedora-10-i386, and nor after updating it.
2) The WMP54G/RaLink device worked rightly after installation of Fedora-9-i386, but not after updating it.
3) It seems strange to me that there is no wlan0 entry in the Network Configuration window, neither for fc9 nor for fc10. (There is an eth0 entry though.) It feels even stranger that the systems connects anyway over wireless, even though there is no wlan0 entry, both for fc9 and fc10.
4) After having manually added wlan0 in Network Configuration window, it seems strange to me that the system tries to connect via wlan0, e.g. after a restart and login even though nothing is checked in the Wireless Device Configuration window for wlan0. (I believe this oddity is valid for eth0 too).
5) For Fedora 10, I get prompted to save the network configuration even in the case nothing has been changed.
View 5 Replies
ADVERTISEMENT
Jun 18, 2009
I just installed Fedora again, after a long absence. I have been using XP. I am having issues setting up my wireless card Linksys WMP54G. For some reason the card has been recognized, and the interface is there. But I have tried every walk-trough known to Google, and it still won't work. I have been using the GUI tools, but they don't work. I have also been using the command line walk through, and they aren't working either. Does anyone know which files I need to set and what the process would be?
View 3 Replies
View Related
Feb 12, 2010
Trying to get Linksys WMP54G (RaLink RT2561/RT61 802.11g PCI) card running in FC12 with WPA. The drivers are included in the distro. No luck with network manager.
[root@nitefall ~]# lspci -v | grep -i network
01:00.0 Network controller: RaLink RT2561/RT61 802.11g PCI .....
When I try to do ifup wlan0 I get:
[root@nitefall ~]# ifup wlan0
Error for wireless request "Set Encode" (8B2A) :
SET failed on device wlan0 ; Invalid argument.
Determining IP information for wlan0...
<hangs there for a while>
I get the above error with or without encryption enabled at the AP. I've been over hundreds of posts on dozens of pages and nothing has worked. I have a dual-boot and the card works perfectly in Windows, so it's not a hardware issue.
View 1 Replies
View Related
Mar 30, 2009
I have an auxillary laptop that I use with Fedora 9 on it. Up until now, I have been using wireless just fine with a an old Marvell card. A friend needed a wireless card, so I gave it to her because I had a spare Belkin card (PCMIA) with a RT2500 chipset. This chipset has been supported in Fedora for a long time, and it does it fact work but it will not obtain an IP address and disconnects from the Network Manager upon every attempt to connect.. I get an error that says "set bit rate" failed and I cannot get assigned an IP address from my router.
I do not use encryption. Nothing I have tried with sysconfig-network has had any affect.
iwlist scan finds the router just fine with a good signal, but will not connect.
View 1 Replies
View Related
Nov 12, 2010
I've just installed Ubuntu 10.10 and everything seems to be working fine, but I can't seem to connect to my wireless network. I am able to see the wireless networks nearby, so I'm guessing that means the drivers are fine and the hardware is working. When I try to connect, I am seeing the wireless networks of my neighbors, but mine isn't showing. So I manually enter the information in and try to connect, but it doesn't seem to connect. I enter the WEP key and it attempts, then the WEP key screen pops up again, as if I entered the key incorrectly. I've tried many times and I'm 100% certain my key is correct. By the way, the chipset is: Ralink RT61
Which means it really should just work out of the box.
View 5 Replies
View Related
Apr 14, 2010
I have bought two Asus NX1101 gigabit cards for my kubuntu box and ubuntu server box. The cards are automatically detected as eth1. However the speed is set to 100mbit instead of 1gbit.
ifconfig eth1 .....
capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=Sundance Technology IPG Triple-Speed Ethernet duplex=full ip=130.89.169.33 latency=64 maxlatency=10 mingnt=80 multicast=yes port=MII speed=100MB/s
resources: irq:17 ioport:ec00(size=256) memory:f7d00000-f7d000ff memory:f7c00000-f7c0ffff(prefetchable)
I noticed that both lshw and ethtool claim that the card does not support 1000mbit. So changing the speed manually with ethtool doesn't work. In windows XP the card works as it should.
View 4 Replies
View Related
Jul 4, 2010
I have found a few older threads that have asked a similar question, but wonder if updates and new devices have improved the situation:
Is there a PCI (not express) 802.11n adapter that will work with 9.04/Jaunty "out of the box"?
View 1 Replies
View Related
Feb 28, 2010
I have a Broadcom based PCMCIA wifi card that works great on an older kernel in Debian after a friend of mine did the fwcutter business.
I just installed Backtrack 4 release version on another laptop. While this card works right out of the box the sensitivity is greatly reduced. The built in wifi card (Intel chipset) can see twice as many APs at any given time.
Now, I know that Broadcom chipsets are not the best but this card normally has fantastic sensitivity and Tx power plus an external antenna connector so I really need to get it working properly. When it's working properly under Linux or Windows it blows the competition away.
View 2 Replies
View Related
Jun 8, 2010
Could anybody confirm that the D-LINK DWA-556 wireless N PCI-E network card works with Lucid Lynx 64 bit? Im looking for a reliable wireless network card that if possible works out of the box on Lucid 64 bit, so far my search has lead me to the above card, If anyone has hands on experience of this card on lucid 64
View 2 Replies
View Related
May 11, 2011
I was uninstalling some programs through the package manager, then restarted. When my netbook turned back on, I had no internet connection and the WiFi icon wasn't showing in the notification area as it usually does either. Says the card is functioning properly and everything. Other devices can connect to the WiFi.I'm kind of new to Ubuntu and searched around a bit, but am at a loss. HP Mini 110Ubuntu 10.10Broadcom BCM4313Edit: Quote:$ sudo ifconfig -s
View 3 Replies
View Related
Oct 29, 2010
I just got Ubuntu and am new at this stuff. I have a dual boot windows 7 64 bit one and ubuntu 10.4. I booted ubuntu at startup and then tried to go online, but it says my wireless device is disabled. I tried pressing the keys on my keyboard to see if that may work, but it doesn't. I am lost and new at this.
View 1 Replies
View Related
May 16, 2011
I recently upgraded my Zepto laptop to Natty (11.04), and unfortunately the wifi no longer worked. I have a WPA net, and the combination with a Ralink chip seems unfortunate - judging from the number of internet posts.After browsing loads of threads on the 'net I think I have found a solution for 11.04 - it will work out of the box in 11.10 !
1) Add "blacklist rt2800pci" to /etc/modprobe.d/blacklist.conf
I think this makes the wifi stuff work as I can then do "iwlist wlan0 scan" and get reasonable output. But there is no integration with the Network Manager. So I have also done this (again, with inspiration from a few threads):
2) Edit /etc/NetworkManager/NetworkManager.conf - change the "managed=false" under "[ifupdown]" to "managed=true".
You may have to do a "service network-manager restart", restart or similar to get it going.It also seems I can suspend and get a wifi net connection upon wakeup.
View 1 Replies
View Related
Jun 10, 2010
I recently installed Ubuntu x64 on my dell studio 1535 using the windows installer (wubi).
All seems to be working fine apart from the built in wireless card, the proprietary driver (found in hardware drivers) installs and activates successfully and works perfectly. Until I shut down or restart the system. On the next boot the wireless card is 'disabled' and no longer works.
The card I have is a Broadcom Corporation BCM4312 802.11b/g
I am going to try a proper install on a second partition rather than using wubi later on but wondered if this was a commonly occuring problem?
The wireless card works as soon as the driver installs, however I am shown a "restart to activate driver" message and after restarting it's dead.
View 5 Replies
View Related
Jun 17, 2009
I was successfully using samba + fedora directory server in fedora 10 as a primary domain controller for my home network (achieved mostly by following barry905's instructions here: [url].
After upgrading to fedora 11, some of the pdc functionality no longer worked.
For example, when i ran 'pdbedit -Lv', i got:
Code:
I was able to fix this by adding to the [global] section in /etc/samba/smb.conf:
Code:
I also found that i could no longer join an xp computer to the domain. i discovered that for some reason, the samba administrator password had been cleared. after running:
Code:
That was fixed.
The last problem, which i have still not fixed, is that roaming profiles no longer work. when i try to do a domain login as user 'htpc' from an xp machine, i get the following message in xp:
Code:
Here's an excerpt of my /etc/samba/smb.conf:
Code:
View 14 Replies
View Related
Jan 25, 2010
As an introduction to the problem I'm having: For a long time, I've been on 9.04 and my wireless worked quite happily. Then when I upgraded to 9.10, to my despair I found that my laptop no longer detects my wireless driver! Before I go on, I should also say I'm rather inexperienced with Ubuntu in general, despite having used it for quite some time.
Anyway, onto the informational part: I'm using a Compaq Presario CQ40. According to lspci, my wireless network card details are as follows:
Code:
03:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
lsusb shows the following:
Code:
Bus 003 Device 002: ID 03f0:171d Hewlett-Packard Wireless (Bluetooth + WLAN) Interface [Integrated Module]
[Code].....
View 9 Replies
View Related
Dec 4, 2010
Just installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
View 6 Replies
View Related
Jan 1, 2010
Ever since I upgraded to the new Ubuntu, I have been having problem with wireless. In the "Hardware Drivers" I come up with 2 drivers:
1) Boadcom B43 wireless driver
2) Broadcon STA wireless driver
I activated the first one, but latter noticed that the wireless was not working, so I tried installing the second and it returned this message:
Quote:
So I unactivated the first and then it disappeared leaving me with the second, and its error message.
Quote:
What should I do now?
The output for "lshw -C network":
Code:
The last few pages of /var/log/jockey.log.
Code:
View 9 Replies
View Related
Mar 10, 2009
Need to swap out my geforce 6200 for a ti 4200 now I could use a newer nvidia card instead if going to an older card would be a problem how should I go about doing this? is it potentially disastrous?
View 6 Replies
View Related
Jul 18, 2011
I have just upgraded my machine from a GeForce 6600 to an GeForce GT 440. After the install, everything seemed to run fine except the KDE desktop. glxgears ran better than before, but KDE had to disable desktop effects and my window's title bars are still disappearing when I mouse over them.
View 3 Replies
View Related
May 14, 2010
I am using Ubuntu 10.04. The Tata Photon+ card Huwai EC1260 was working flawlessly. However, I recently did a firmware upgrade on the card that was provided by Tata Indicom for it to work on Windows 7.
After that, the card is no longer detected as a mobile modem in Ubuntu. If I try to add a new connection, all options are disabled (whereas earlier Tata Photon card would appear automatically).
The product ID has changed. What change can I make to Ubuntu to enable it to detect the card again.
View 6 Replies
View Related
Mar 3, 2010
I've got a Linksys WMP54G Pci card of some kind that's being reported as a Ralink rt2500 pci, but it is very slow (50k/s cap) and has jumpy signal strength (goes between 70% and 10% every second or so, while the router is in the same room). It is just this pc, as I'm using my laptop fine right now with no such condition. I am running basically a fresh version of Slackware 12.2, so it's kernel version 2.6.27.7. I have used this with Slackware 13 and there was absolutely no issue, so I think it may be a wrong or outdated driver, but building kernel modules and updating whatever module it should be is not something that I'm very good at.
View 3 Replies
View Related
May 10, 2010
Ok, so I upgraded my acer aspire one to the new Ubuntu 10, and at first everything was working fine, except the audio. Now, for some reason, my wireless and ethernet ports have died. I can't get online by either method. I can do ifconfig <device> up and it will show up if i do iwconfig or ifconfig, but the wireless isn't associated with the AP. Currently I'm trying to load some drivers for my atheros card, and we'll see how that works outReally I was wondering, how come the modules don't load at boot time, and how can I fix this? I've been a Linux user for quite sometime, however I've been more of end user
View 1 Replies
View Related
Dec 3, 2010
1. D-Link DWA-643 Xtreme N Express Card Adapter The onboard wireless for my HP tx1000z stopped working a long time ago. This wireless adapter is in my express card slot.
2.
Code:
$ lspci
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2)
[Code]....
View 2 Replies
View Related
Nov 26, 2009
I used preupgrade to upgrade from F11 to F12. In F11, I used the proprietary nVidia drivers from rpmfusion, and they worked well. I have refrained from installing the nVidia drivers in F12, because of the problems reported for users of KDE. I removed my old xorg.conf, which has references to the nVidia driver and to "TwinView," the proprietary method of managing two screens, so as to let X discover both monitors.
Now, however, my second monitor stays black, even though xrandr and KDE RandR show both monitors correctly. Xorg.0.log shows the nouveau driver is loaded. (I also tried to create a new xorg.conf following guidelines from the web, but many of the guidelines are from before xrandr, and I'm not confident I have it right yet.) It seems that X believes I have two monitors, because I can drag a window off into the blackness (and it's never heard from again!) I know that the hardware is working, because I just booted into Windows 7, and I could see the desktop on both windows.
How do I convince X and KDE to display on both monitors?
View 2 Replies
View Related
Mar 29, 2009
I have installed apache. The problem is that localhost works but not the ip for viewing my hosted sites.
How can i rectify this error?
View 5 Replies
View Related
Sep 6, 2009
I used the following guides to try and get my Netgear WG511 PCMCIA card going:
[URL]
I also made a post about it here: [URL]. As the problem doesn't appear to be ndiswrapper itself I've made this separate post.
Unfortunately, I still end up having wlan0 attempting to connect, prompting for my password, trying to connect then prompting for my password (ad infinitum).
I changed my network security from WPA to WEP and now my card works fine. why this might be happening (i.e. why WEP works but WPA doesn't?)
View 2 Replies
View Related
Mar 21, 2009
Yes, another newbie question. Just loaded and updated FC 10. Everything works great with dhcp. Tried to setup static ip to learn more about how to set it up and nothing seems to work. I'm connected to DSL via a router when I ifconfig I get:(basic stuff)inet addr: 192.168.1.7 Bcast: 192.168.1.255 Mask: 255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
I have also tried default gateway 192.168.1.255 and 192.168.1.254.Most of what I have tried above has come from linux websites and faq's.Keeping in mind I am worst than any new newbie you have ever worked with
View 13 Replies
View Related
Jun 17, 2009
Since I installed FC11 I can't get vpnc to work (I always getno response from target").Also I can't ping any external IP even with the firewall disabled.What I see strange is that I had the same configuration in FC10 and the router configuration seems okay to me:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
10.64.64.64 * 255.255.255.255 UH 0 0 0 ppp0
[code]...
View 3 Replies
View Related
Oct 18, 2009
I'm pulling my hair out to figure out what's gone wrong. I have a small home network with a router and 4 computers, 3 linux boxes and 1 windoze machine.The windoze machine and 2 of the linux boxes (newer ones, one with FC11 and the other with Ubuntu Hardy) are using the router's "Set Static IP" option just fine. However an older FC5 machine I have always gets its IP assigned randomly. As this is the machine I ssh into from overseas via a Dynamic DNS, this is a huge frustration when the power goes off or I need to restart the machine. It's usually 192.168.0.2 but sometimes 192.168.0.3 and occasionally other numbers as well. It _should_ be 192.168.0.130. As near as I can tell, I'm doing everything the same between the machines. The router config is very simple and works for the other systems so I suspect I may have a legacy tweak that I did years ago that's causing the problem.
Anyone know what I can try? I'm afraid I'm not a networking guru (ahem, wouldn't be posting if I were!) so things like "check the this" will be more helpful if there's a clear example. "Check the this...emacs /etc/thisfile/config" and see if XYZ option is TRUE" is far more useful. Again, many thanks. If none of the systems were working right then it would be totally different...but 3 seem to work just fine and happily get their assigned static IPs. It's the one non-conformist that's the trouble...
View 1 Replies
View Related
Jun 8, 2011
I'm running Telnet Server, VFTP, and VNC on a Fedora 14 box. The box's internal IP is 192.168.1.222 This machine is configured to live in the DMZ, The firewall is up on both the router and this box. I can remote in from home using our external IP. I can FTP. I can Telnet. All using our external IP. When i'm in the office, i can remote in using our external IP. I can FTP. I can Telnet. Again, all with the external IP. If i attempt to telnet 192.168.1.222 i get a connection refused. i can ping the 192.168 address
nmap tells me that all 1000 ports on 192.168.1.222 are closed
nmap tells me that my expected ports are open on the external IP.
.... This is a relatively new conundrum as it "used to work", and only appears not to since our last reboot (power outage). I know i have to be missing something simple here, but i differ to the experts.
View 5 Replies
View Related
