I'm using F15 with Gnome 3 and Gnome Shell (Default Environment).
I'm looking for some sort of solution to have different clocks (of different time zones) displayed on my desktop! Anything such as gadgets, screenlets, ...
I've been using my laptop with an external LCD monitor attached to it at work (Philips 201E). And at home with a different external monitor (Samsung 2032BW). I have an ATI graphics card (HD3450), with Ati Catalyst drivers enabled and I'm using the Single display desktop (Multi-Desktop) seeting. At work I have the external monitor on the left and laptop on the right, while at home the other way around. So when I switch between the two setups, I just needed to go to Ati Catalyst Control Center, change the order of the displays, change the resolution (Home - 1680x1050, Work - 1440x900), reboot and it was all fine.
But since a while it doesn't work properly anymore:
At home it *still* works fine. At work it doesn't work. Sometimes it works for some reason, after a few resolution/setting changes in ACCC and reboots... it's very strange and annoying. Does anyone have any idea for fixing it? I've uninstalled and reinstalled the ATI restricted drivers and that seemed to make it work initially, but it still works just sometimes. This is my xorg.conf currently:
Code:
Section "ServerLayout"
Identifier "amdcccle Layout"
Screen 0 "amdcccle-Screen[6]-0" 0 0
Screen "amdcccle-Screen[6]-1" 1280 0
EndSection
[Code]...
I need some help to setup a simple 2 screens extended desktop. From my laptop with an nvidia card, it was very easy and done in seconds. But with my new desktop loaded with amd hardware, it's turning into a nightmare. I've posted on details of my hardware and of this problem here, and I'm encountering new trouble. Since then, my xorg.conf has changed a little without success:
[Code]...
I've been using my laptop with an external LCD monitor attached to it at work (Philips 201E). And at home with a different external monitor (Samsung 2032BW).I have an ATI graphics card (HD3450), with Ati Catalyst drivers enabled and I'm using the Single display desktop (Multi-Desktop) seeting. At work I have the external monitor on the left and laptop on the right, while at home the other way around. So when I switch between the two setups, I just needed to go to Ati Catalyst Control Center, change the order of the displays, change the resolution (Home - 1680x1050, Work - 1440x900), reboot and it was all fine.
But since a while it doesn't work properly anymore: At home it still works fine. At work it doesn't work. Sometimes it works for some reason, after a few resolution/setting changes in ACCC and reboots... it's very strange and annoying. With the home monitor I can see the whole bootup process on both monitors (laptop + LCD) and it always just works fine. With the work monitor on the external LCD monitor I just see "No video input" until I get to the login screen, then it shows up there as well. But after login it will either:
[code]....
I had Ubuntu Maverick as my only OS.Then I installed Windows 7 for dual-boot because I need to use some programs for school. But now I can't get the clocks to work right. If the time is wrong in Win7, I change it (it has the right time zone), but then when I go to Ubuntu the time is wrong.Then I change the time in Ubuntu to fix it, but when I get to Win7 the time is wrong again.
View 1 Replies View RelatedA few distributions back the option to display a clock on the gnome-panel in GMT was removed, however to preserve backwards compatibility the option was left in which you could edit by hand or through gconf-editor. Since I have upgraded to Ubuntu 10.04 I've noticed that the option does not work any longer.
My method has been:
$ gconf-editor then under: / -> apps -> panel -> applets -> applet_N -> prefs set: gmt_time = True
I had to reinstall Windows recently, which reset my clock under Linux. No problem, I set the clock, and then set the hardware clock to the system clock. Rebooted under Windows, and both were fine. After rebooting into Slack, it is again a few hours off. How can I change this permanently?
View 6 Replies View RelatedWithin a VMWare ESX virtual machine, I am running CentOS 5.2. (Actually, it is kind of a virtual appliance to run CollabNet's Teamforge - which I have installed for a trial). I've been dabling with Linux for a year or so, but I know I have much to learn.
I'm attempting to run a cron job that runs a backup script at 11pm. It works great, but unfortunately it runs at 11:30 am.
I created the cron job using 'crontab -e', while logged in as root. My cron job line is : 0 23 * * 1,2,3,4,5 /etc/tjt_backup/collabnet_backup.sh
If I type 'date', I get the correct date/time in my timezone: Tue Mar 9 16:27:12 CST 2010
If I type 'clock', I also get the correct date/time: Tue 09 Mar 2010 04:26:57 PM CST -0.463330 seconds
(Although, it appears there is a little drift)
I have an ATI Radeon HD 3300 on-board video chipset, and an ATI Radeon HD 4350 PCI card. What I want is to have both displays available from one mouse/keyboard. I want to play media on one and have the other as my main desktop.The problem is that with Xinerama enabled, KDE desktop effects do not work (KDE says XComposite and XDamage are not available, even though I explicitly enabled them as extensions in the xorg.conf file), and performance is quite bad. Without Xinerama enabled, performance is great, desktop effects work great, but there's a lot of trouble with full-screen video, and the KWin window manager does not apply in the second display (although I can run a second instance of KWin on :0.1).
View 2 Replies View RelatedWe are doing a project related to clock synchronisation. We have two laptops: Compaq and IBM Thinkpad. If we adjust the clocks of two laptops to same time in HH:MM:SS using datefunction, in about half an hour, both the clock drift by about 10-15 min We are wondering how this is possible???We have compiled kernel 2.6.36.2 on both laptops and set the value of HZ to 1000. Then what is the reason for such a significant drift in short interval of time??Is this related to crystal oscillator or anything else?
View 5 Replies View RelatedAnyone successfully using VNC client on a Mac to control a Debian server?I have the vncserver setup on the Debian machine properly. But I'm having problems connecting to it from both a PowerMac running Tiger and a MacBookPro running leopard.I can connect no problem from a machine running Slack12.2, have not setup port forwarding on my router to connect remotely yet.My Debian machine is running the latest stable release of squeeze with KDE4.I originally tried this with RealVNC Enterprise for OSX but I'm not gonna buy it so I need another alternative after the 30 day trial ends as they have no free version for OSX.
The situation is that I do freelance graphic design on the PowerMac with Cinema4D and Photoshop so I spend most of my time on that machine which is located in my home studio in my attic. Aside from the MacBook and a Dell desktop(family machine)all my other machines and network hardware are in the basement. So to go from the attic to the basement everytime I need to do something on another machine is not practical, and the only other machine I need to access on a regular basis is the Debian box in the basement, this makes the most sense.
I also have a 14 year old living in the house and he's fascinated by all this and will meddle in anything he gets the chance to so all the Linux machines and network hardware need to be behind lock and key.
I continually get times where an applet on the top panel breaks, such as the Indicator Session Applet, where it doesn't show the applet, and is mimicking the clocks display, but frozen, and no functionality. This is seen in the photo, where you can clearly see the right time and applet as 5:11 and the frozen one as 4:49.
View 1 Replies View RelatedNow that Ubuntu 10.04 has multi-touch capabilities built-in, if I do not have a multi-touch screen or surface device, can I get 2 USB mice and get 2 pointers on the screen? One for the right hand and one for the left hand as I am ambidextrous, and would find it very convenient to have 2 mice.
View 4 Replies View RelatedIm running 64bit centos 5.6 and using virt-manager.On one of my guest OS's, Windows 7, The max Physical CPUs is 2, you can have unlimited CPU Cores however. (like my machine i use for work has 1, 4 core processor).The issue im having is xen only allows you to set the vcpu arguemnet in your xen config file. How can i set it so that 1 CPU has several Cores just as windows would recognize this machine if i were installing directly to the hardware vs via a VM.Ive searched for 2 days staright trying to address this issue, very little progress, Does anyone know where a XEN support forum is? all i get is the citrix xen support forums.
here is the best info i have found on this, but i dont know how to change this for my CPU to work, when i enter this in my xen config it essentially ignores it and just takes the value of vcpu= so windows shows 2 CPUs each with ONLY one core. Id like 1 or 2 CPUS showing Several cores.The physical Hardware is 2x Xeon 5300 Quad Core CPUs.
> # Expose to the guest multi-core cpu instead of multiple processors
> # Example for intel, expose a 8-core processor :
> #cpuid=['1:edx=xxx1xxxxxxxxxxxxxxxxxxxxxxxxxxxx,[code]........
How can I setup my Linux server to automatically synchronize its server clocks? We need to ensure our server clocks are set to the correct time always.
View 2 Replies View RelatedIt seem like a good idea to leave the computer along when it is updating. Because if for some reason I still using the computer, it might interrupt the updating process.(e.g. update manager freeze, or corrupt some file) I remember I run into this problem quite a few times back in FC6, but did not have problem on F10 and F11(merging from preview?) until the day before yesterday. I was tried to downloading a relative large file updating system and running 2 folding at home in the terminal at the same time (ram usage at the time was around 300+/512). Then disaster strike. The hard drive spin like crazy with large cpu I/O pending(or wait time?). The problem reoccur during the boot up and login after the update.
And this is the message continue recorded in the (F11) log:
Oct 17 11:52:22 localhost kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
Oct 17 11:52:22 localhost kernel: ata1.00: BMDMA stat 0x24
Oct 17 11:52:22 localhost kernel: ata1.00: cmd c8/00:08:22:9c:57/00:00:00:00:00/e6 tag 0 dma 4096 in
Oct 17 11:52:22 localhost kernel: res 51/40:07:23:9c:57/00:00:00:00:00/e6 Emask 0x9 (media error)
Oct 17 11:52:22 localhost kernel: ata1.00: status: { DRDY ERR }
Oct 17 11:52:22 localhost kernel: ata1.00: error: { UNC }
Oct 17 11:52:22 localhost kernel: ata1.00: configured for UDMA/100
Oct 17 11:52:22 localhost kernel: ata1: EH complete
I saw this message in F10 before, and had been told it might have something to do with the kernel. But I suspect the problem is source from corrupted file rather than kernel this time around, since back then the problem will go away after a successful file system check. Unfortunately, it does not work this time. So I have no choice to reinstall the system. Therefore, I am thinking if it is really a bad ideal to let the computer muti-tasking during the update? Because it may rise the possibility of update failure or system files corruption. I really do not like LVM, is there a way to get around it? The installer from live usb does not allow me to customize partition during the installing....
I have asked about this issue before to no avail but since then I have been able to narrow down the main cause of the crashes. My setup:
HD5770 - Running 2 19" LCD's
HD3300 onboard Running 1 47" lcd
Whenever I am in firefox and have pictures open in the browser and move the mouse to the other 19" monitor it crashes, not everytime but often enough to be annoying. Sometimes when it crashes the screen goes blank and I wind up at the login screen, other times it just goes blank and stays blank.
how do you get color in the terminal like DSL in red-hat 9.
i have red-hat 9 running on a old 3dfx gaming pc I'd post a pic of the DSL terminal but the site would not let me
Many people have multi-core cpus supporting frequency scaling now, if you want to see if the workload is being evenly distributed then add as many CPU Frequency Scaling Monitor applets to the Gnome panel as you have cores/cpus. Then right-click each one and select preferences and choose which cpu to monitor.
Now compile a large program or run a cpu intensive game and watch how the workload dances around between the two (hopefully)
Some clever apps like gnome chess will multi-thread and make max use of both cores, sadly many others won't.
Ive loaded 64studio (hda6) grub in MBR, and fed10 grub on its partition (hda8), but from Studio it seems i cant Mount fed10 files to look at the Kernel path from MBR. (studio did not auto pick it up, like it did for Mandriva on hda7)
Does anyone know what it is ? something like kernel /boot/vmlinuz.....and Initrd(hd0,7)/boot.initrd.img .....then i can Edit menu.Lst in MBR grub.
I've tried searching the forums / google and haven't been able to come up with anything... in Debian-based distros there's an option that can be set to allow boot concurrency so that multiple processor cores can be used for the boot process. Windows also has an option similar to this to specify how many processor cores to use for boot.
Is there an option for multi-core booting in Fedora?
Opened with Gimp multi - page document. It opens fine and gives the layers! When I do : File, Print to File, pdf it gives out only one page! How to get all pages out?
Also when gimp loads all pages they are in layer! Is there a way how to see everypage without swiching written text off to see the next page. Because for mee its
Now if Im here and want to see again stage in y, I need to swich off all layers from y to z? It's normal or is there a way how to see all that in different way?
I just switch to fedora from windows recently. And I love the terminal of fedora alot. The problem is when I run some command on the terminal, I need to wait for that command to finish before executing another command. This is very inconvinient, say If I open eclipse using the terminal, this eclipse program will hog to the terminal until I closed it. So if I want to use terminal again I have to open another one.Hence the question is: Is there any way open multi processes(command) using only one terminal?
View 4 Replies View RelatedI am using Dell latitude e6410, fedora 14 64 bit.
i want to install multi touch touchpad, for now its not working...
So I'm new to modifying Grub, and I've recently setup my laptop to contain all of Windows 7, XP, and the Fedora 13 beta on a single drive.Grub is currently setup to boot to Fedora, and the Windows 7 boot loader, and from there I can boot to XP.I'd like to set it up however, to have XP boot "directly" (i.e. bypass the 7 bootloader and go straight for the XP loader).The current setup is:
Partition 1: 7 ntfs on sda1 (primary)
Partition 2: sda2 (extended containing sda5 XP ntfs)
Partition 3: sda3 ext4 containing /boot
[code]....
I am currently booting 4 flavors of Linux - Ubuntu 10.04, Xubuntu 10.04, Linux Mint 9 KDE RC and Linux Mint 9 Gnome. There is so little difference between Ubuntu Gnome with the right packages installed and Linux Mint 9 it is redundant and I would like to replace it with Fedora 13 and try that out for a while. I understand that Fedora still uses a legacy Grub while the others are all using Grub2. I also understand that the two bootloaders do not get along. Is there a way to do that? How? If I have Fedora install its legacy Grub to the Fedora partition will Grub2 see Fedora and update itself properly? I'm open to starting clean if that would simplify things.
View 4 Replies View RelatedFew days ago, the server did not respond to a ssh request from a user at night. A user tried to check what went wrong with computer and tried to login from terminal next morning. As the computer was unresponsive, he somehow decided to boot it by turning the power off. To make the story short, the server rebooted; however, he can't login to his account. Actually, the server could not start some processes; but was able to ask user to enter his account username. Even though, he enters the correct username and password, server does not accept the request. I also could not login as root.
I just checked the server logs by booting it in single user mode. Here are some interesting lines:
Before the reboot:
irqbalance : can't balance irqs on a uniprocessor system: failed
After the reboot:
irqbalance : can't balance irqs on a uniprocessor system: failed
fsck:
This might be something related with shadow file.
Here is part of /etc/shadow
Currently I'm running 3 operating systems on my machine; Windows XP, Windows 7 and Fedora 14. I've installed them in the following order: XP -> Win7 -> Fedora14, with the idea that this would work fine regarding operating system selection at boot time.
But unfortunately, I just installed Fedora, and now I'm unable to boot Windows 7/XP. When I select the "Other" option in the Grub menu, I get the following error: Code: Error 21: selected disk does not exist To provide as much info as possible, here is a boot info script log:
[Code]...
I have a multi-sector nrg file that I would like extracted. I can't seem to find a way to extract the contents of it! Please tell me if there is a tool I can use to do this!
View 2 Replies View RelatedCurrently I'm running 3 operating systems on my machine (in order of installation); Windows XP, Windows 7 and Fedora 14. Unfortunately, after I installed Fedora I'm no longer able to boot Windows 7/XP. When I select the "Other" option in the Grub menu, I get the following error:
Code:
Error 21: Selected disk does not exist
To provide more info, here is a boot info script result:
Code:
Boot Info Script 0.55 dated February 15th, 2010
Boot Info Summary:
=> Windows is installed in the MBR of /dev/sda
=> Grub 0.97 is installed in the MBR of /dev/sdb and looks on the same drive in partition #3 for /grub/stage2 and /grub/grub.conf.
=> Windows is installed in the MBR of /dev/sdc .....
mdadm: No arrays found in config file or automatically