Previous Fedora releases allowed me to connect to my external monitor via an HDMI-DVI cable to use as my main monitor from my laptop. However, after I did a fresh install of Fedora 15, I have this problem that when I login to gnome 3, both laptop screen and external monitor go blank. I cannot ctrl-alt-f2 to go to terminal. I end up having to ssh from another machine and reboot. Each time, the reboot doesn't even work since I have to go and kill Xorg before it starts to reboot.plymouth and gdm seem to be fine and show up the external monitor. It is only when I login to gnome3 that I get the blank screens.
I have installed Fedora 15 64bit live with no apparent errors and I get to the "Welcome" where it says just a few more steps before I can start using Fedora after filling in the details hit the "Forward" button in the lower right hand corner. The problem is I can't see the forward button, its like I need to page down or something but everything I have tried isn't working. I then decided to use the Fedora 15 64bit DVD thinking a driver was missing or something and it is still the same issue. I am using a Thinkpad T61 laptop with an external monitor and the external monitor goes blank when it boots to the welcome screen, but I can scroll over to the external and see the mouse cursor on the external. It seems that if I could see the welcome screen on the external monitor that I might be able to see the "Forward" button. Both installs went without a hitch, the DVD install found my internet connection and downloaded a bunch of stuff and the DVD install took about two hours to complete, again with no errors reported. I hope I am not being daft here and missing something obvious.
After the login screen, my laptop screen is active but the external LCD monitor hooked to my laptop goes blank which was active to that point.
Here are quite a few details which might help you in diagnosing the problem
alt + clt + f1 takes the monitor screen to command line but alt + clt + f7 fails to bring it back to GUI. The monitor just freezes!!
Contents /etc/X11/xorg.conf # xorg.conf (X.Org X Window System server configuration file) # # This file was generated by dexconf, the Debian X Configuration tool, using # values from the debconf database. #
I am running Debian 8.3, and I'm running Gnome 3.14.1.I have an external monitor plugged in with HDMI, and while Linux is loading both screens are on duplicate. Once the GUI kicks in, only the external screen works, so I have to enter my password blindly. Then, I open a terminal and run
I am having problems getting my external monitor to work. When I plug in the monitor, both the laptop screen and the external monitor go black. When I unplug the monitor, the laptop screen works again. When I startup with the external monitor plugged in, neither screen works or teh computer hangs or something.
I have had the external monitor going on a couple of occasions. I did manage to configure my monitors through System Settings > Display. I turned off the laptop monitor as I just want to use the external. But after rebooting, things didn't work.
I have an external monitor connected to my laptop (extended display). I always drag the Totem player from the laptop screen to external monitor to watch video files. I wonder, if the Totem player can be set to open in the external monitor automatically, everytime I open it?
My software and hardware information are as follows. I have Fedora 12 and KDE 4.4.5 installed on a Dell Vostro 1500 laptop. I believe it's a 64 bit processor; it's an Intel Core 2 Duo CPU. The external monitor is a Dell as well.
My problem is that my system does not seem to be detecting an external monitor that I have connected. Everything else is working just fine; however, I would like to have the option of attaching an external monitor. When I plug the external monitor into the laptop, the external monitor remains black and appears to be in power save mode. The results of xrandr -q (with or without the external monitor attached: it doesn't appear to change) are as follows.
Code:
How can I get my laptop to recognize that the external monitor is even connected? Let me know if I can be more specific or provide additional details.
I run LXDE with Openbox as WM on Fedora 15. When I watch videos with Totem or VLC, the monitor doesn't register any activity, and goes into power saving mode (goes blank) after a certain amount of time (about 10-15 mins). How can I prevent this from happening? (I just switched over to Fedora from Arch, using GDM and Openbox. I didn't have this problem on that installation, so it's probably not hardware related.)
I have a small problem after connecting a LCD monitor to an acer netbook. I need to figure out how to make the monitor the primary. Right now, the netbook has the panels, but the monitor has the desktop. I would like the panels and desktop on the monitor, even if that means not using the netbook screen. I have a screen shot below. I am running F13 with Gnome.
Edit: Never mind. I figured out how to disable the netbook screen using the function keys on the computer.
I installed FC11 on my laptop T43 and the video card is ATI Mobility Radeon x300. Now I have a problem of screen resolution with external monitor:
When I do presentation, I have to mirror the two monitors and both set to 1024*768, which is not perfect.
I remember that when I use RHEL 5 desktop edition, The system can automatically detect the external monitor and set it by itself ----- The laptop uses 1400*1050 and the external monitors such as projector uses 1024*768. But I haven't found such feature on FC11.
I have a Lenovo 3000 N100 laptop which LCD does not work anymore.So I borrowed a monitor from my friend and started using it(it has been few days).I had installed Fedora-12 few months ago. After connecting the external monitor, I found that this one shows good graphical start-up but just upto the login screen(just before the login screen, login-screen does not come) and it proceeds no more.Though I can get the virtual consoles restarting xserver is of no use
I recently installed Debian, using the amd64 Network Install .iso. I'm using XFCE4 as my desktop environment, and everything is working well... on my laptop's screen.
My desired setup is to have my laptop sitting on a well-ventilated shelf, closed, and to have an external monitor be my main monitor. I want this because I'm using my laptop as my "home" computer, so it never moves, and I don't like the keyboard/trackpad. My laptop has a VGA output, and I can get my desired setup on my Windows partition (not stating a preference ; just that the hardware CAN do what I want it to).
I've been working my way around the Internet for a few days, now, and I've got the commercial NVIDIA driver installed. If I run sudo nvidia-config --twinview I can get my external monitor to be part of the display, which is great, but it's part of a dual-screen monitor setup, which is not what I want at all, because (a) XFCE's multiple virtual desktops are good enough for me and (b) my graphics card is integrated, and I'm trying to squeeze every drop of performance out of my laptop that I can (1 gig of RAM; the less that my graphics card eats into it, the better). Plus, it'd be annoying to accidentally drop something on my laptop's screen, and then have to dig it out of the shelf in order to undo it. I'm not saying that I'm consistently clumsy, but I'd eventually end up doing it.
I'm a newbie so apologies if there is a trivial answer to this.
I (maybe somewhat rashly) tried to connect my tv to my laptop (Dell Latitude D400) running Ubuntu 9.10.
I plugged in the cable, went to the System>Display menu, where it had detected the model and make of tv (Samsung 19" LCD) (I think the resolution was 1650 x 1050 or similar). I clicked the box to activate the second monitor with the "Virtual resolution" adjusted. It told me to log out then log back in.
I accordingly logged out but then couldn't log back in. It had evidently changed the resolution not only on the 2nd monitor but also on the laptop monitor. A box was visible on screen but completely illegible/unclear since the laptop monitor couldn't display that resolution.
After a few restarts and button pushes it is now restarting at a terminal (I enter my username/password at a command prompt on an otherwise blank screen rather than the graphical interface loading up).
Question: are there any commands that could change the resolution back to its original settings then restart the Ubuntu graphic interface? Some thing similar to the "load with last known good configuration settings" option in Windows maybe.
I have an Acer Aspire 5100 with AMD turion 64X2 and an ATI radion XPRESS 1100 graphics card.I recently installed suse 11.2 (clean install) without much trouble but I've always had some intermittent trouble were the screen would just go blank after boot up (before login screen) this did not happen always and never happened in safe mode or on XP on the same laptop, ergo software fail.Anyway, this morning I have a laptop with absolutely nothing on the screen from start to end. I also get a loud beep followed by two shorter beeps!If I let the boot up progress I can blindly find myself in normal Suse or in safemode or even in XP all without anything on screen
I just replaced my PSU and now my computer is not booting up. To make sure that my new psu is not causing the problem, I put my old one back in but it still doesn't boot up. My system powers on, motherboard led glows, the processor starts running and so does the graphics card. The monitor stays blank though. Nothing shows up on the monitor. Just a blank screen with the monitor led blinking. What could be the problem ? It was working fine before I replaced my psu.
I installed Natty on it with the machine hooked up to a Samsung LCD with a 1680x1050 resolution over DVI. No problems at all. I want the box to pretty much output MP3s and web video, so I'm not needing much. When I take the box and hook it via DVI to my LCD, I get a blank screen on boot up. I try sticking the natty CD in it, and I get a blank screen trying to live boot it too. The LCD doesn't do 1680x1050, so I brought it back to my Samsung and set the default resolution to something nice and safe: 1280x1024. Still the same behavior. When I take splash mode off, I see a "load fallback graphics devices fail" error as it is booting up. Hard for me to think the driver is the fault here when it works on my over LCD just fine.
I have a new ubuntu 10.04 install, it is the third that I have done recently. On this particular install (unlike the others) the screen goes unexpectedly blank at seeming random intervals and any motion restores the screen. It is acting like a screen saver with the blank screen option set. My screensaver preferences are set to use a screen saver 'for a 7-minute idle period. The lock screen option is off. For AC power management never is chosen for "put computer to sleep" and 30 minutes is chosen for the "put display to sleep" option.
I put a blank CD (Verbatim CD-R) into my external CD drive using 10.04 LTS. Dmesg shows:
[ 255.950512] sr 3:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 255.950527] sr 3:0:0:0: [sr0] Sense Key : Illegal Request [current] [ 255.950542] sr 3:0:0:0: [sr0] Add. Sense: Logical block address out of range [ 255.950558] sr 3:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 [ 255.950589] end_request: I/O error, dev sr0, sector 0
When I go to /media there are no directories that could be the CD-ROM. I therefore cannot 'see' the CD (which is blank btw). I then went into XP. Windows Explorer could see the blank CD. I then wrote to it. I then went back into Ubuntu. Now when I put the CD into the external drive Dmesg shows:
[97.594505] ISO 9660 Extensions: Microsoft Joliet Level 3 [97.674629] ISO 9660 Extensions: RRIP_1991A
When I go to /media I see the name of the CD. Why will XP and Ubuntu see the CD with information on it but only XP can see the blank CD?
with KDE everything works fine (both monitor show their configured displays correctly), however oddly with gnome when i try and setup dual monitor display, i get blank screens on both monitors, however on the display 0 on the left side there is a full column single pixel width green strip. the rest of display 0 and 1 are blank, however my mouse will move around both display correctly.
I just installed ubuntu 10.10 did a clean install, formatting the previous ones. Install completed successfully, rebooted, entered in GRUB, chose linux, linux starts the my screen goes black, there is no signal coming to my monitor, linux runs fine though i think because I hear the ubuntu login drum. I press ctrl+alt+F1, but can't get to console either, the screen is looking for input signal. Should note the I have a Palit NVdia 9600GT gpu because I saw that people with NVdia card sometimes have similar problems.
Recently the power went when i was using ubuntu and my system shut down since the ups took too long to supply power. So i started my system and choose to boot linux, but it said display drivers not detected, linux running in low graphic mode, and it said 1. run windows in low graphic mode for now...2. reset to previous graphic mode- i chose this and it restarted, since then the ubuntu loading page appears and then my monitor goes blank although my processor is running.....why is this happening?.....i have a ati 5770 graphic card through which it should display.
In installing Intel Fortran Compiler for Linux in my HP Laptop running on FC6,the rpm for debuger shows a dependency error for libXft.so.1. On searching in my system, foundlibXft.so and libXft.so.2. I downloaded and installed the rpm package "xorg-x11-libs- .8.2-37.FC4.49.2.1.i386.rpm"(rpm for FC6 was not found) with 'rpm -i' option. On rebooting Fedora, nothig displayed in monitor except few initiliation messages. I booted the system with FC6 installation DVD and tried to uninstall by mounting as 'chroot /mnt/sysimage' with 'rpm -e' command, but en error message comes as "error, the package 'xorg-x11-libs- .8.2-37.FC4.49.2.1.i386.rpm'is no installed". On booting from the system, i found the same problem.
I changed may graphic card, earlier I used NVIDIA FX5500 with nvidia driver, now I was trying to use ATI Radeon 7500, but there are problems with graphic configuration. At first attempt server started but after I changed a screen resolution the monitor went blank. I restarted a computer but after the X server started immediately the monitor wnet blank. I found that for completely for me unknown reasons Xorg was trying to use an NVIDIA glx module with radeon driver. I removed this nvidia driver, I expected ubuntu would be able automatically to set up a proper configuration, but instead of ubuntu complained about a missing driver. I also tried manually to set up some basic config using Xorg -configure but after that the Xorg server was stuck.
When i turn on my monitor the screen goes blank, but the 'on' button is lit up. Any ideas of what the problem could be?edit: When i turn off and turn on my monitor, it displays what's on my computer for a couple of second and than the monitor turns off again.
So after I installed the ATI Radeon 3400 series video card in my machine, the Xserver cant start! after it loads, it takes me to the init 3. When I tried startx, the screens either go blank or doesnt let me.
I tried to install everything following this website: [url]
I wanted dual monitors but now I cant even get one. The xwindows doesnt appear.
Things I tried: 1. Deleted the xorg.conf and reconfigured (didnt work). 2. sax2 -r -m 0=versa (didnt work) 3. reconfigured the ATI radeon driver from init 3 (didnt work) 4. copy and paste the oold version of xorg.conf (didnt work) 5. tried to run set apt or dpkg-reconfigure command (commands not found) 6. tried xconfig and prompt the best I coudl (didnt work). 7. aticonfig commands (As shown in website) (also didnt work)
I have the live CD to run it from there but I dont know what to do once I get to the terminal.
Is there any way I can revert to previous configuration since the ATI driver gives me some problems? Like a restore function in windows?
How or what files I should change for the X-server to run properly (is there any other file than xorg.conf?....)
The monitors I have: 2009W Dell Monitor 1398 Dell Monitor (I wan to get the dual exntended monitor but it seems to gave me only the mirror image, thats why I tried to reconfigure the video card)
VideoCard: ATI HD Radeon Mobile 3400 Series
Computer: Dell Optiplex 680 (i believe) with SUSE 11.26 and x86_64 bit
Last Thursday, 3/11, I installed a new mother board (ASUS M4A785TD-V EVO), AMD Athlon II X4 Processor, 4Gig DDR3 ram (RIP JAWS), 1 SATA DVD drive, along with my 2 IDE HDD's. The display was OK during BIOS review, and boot UNTIL it came to mounting x-graphics, at which point the screen went black, and a display message came up saying Out-of-RangeHf: 30KHz-70KHzVf: 50Hz-90HzCurrent Frequency:90.3KHz, 60.0Hz.
Does anyone know what is causing this? I mean, is there no way that Deb 5 X86 is going to run on a quad 64-bit system, or can something else be wrong? Before changing hardware, I had seen indications that this system was backward-compatible to older systems, and the more in depth study I've done since seems to verify this.y be, however, that I completely mis-understand what I am reading - this is all pretty new to me.
I tried booting into Debian 4, Libranet 3, and Linspire 6. They all complained loudly, but differently, about x being inoperable. I can't tell you how they complained because I can't go back and check them. THAT is because, in BIOS, I was testing the system with all the different options for "Internal Graphics", to see if one would work. One of these options was "Disabled". Oh-ho-ho! BAD MOVE!!! it's disabled, all right, including BIOS! I can't believe it. There was no warning, whatsoever. I assumed no engineer in his right mind would allow that option to lock out the BIOS without SOME kind of warning. I'm going to try to call ASUS tech support tomorrow to see if they have a solution, but if anyone knows how to reverse this, please let me know. I suppose the only answer is a separate graphics board. But I don't want to get that if I can't use this MotherBd.-processor setup.
I recently tried to plug in a second monitor to my graphics card in an attempt to mess around with a dual monitor set up. This created a duplicate effect (which I expected at first) but downgraded my original monitor to the second monitors max resolution. Now my xorg.conf appears to be blank and I dont believe my fglrx drivers are working anymore.
When I try to start compiz from bash I get the following:
Code:
When I attempt fglrxinfo:
Code:
I'm running Kubuntu, Karmic AMD64 ATI Radion x1350
What could have happened? All I did was plug in a second monitor and restart!
i have my pc connected to my 24 inch lcd monitor via DVI and my laptop via VGA. i noticed ubuntu is slightly more blurry than the pc. would the difference likely stem from the manner of connection or faulty drivers on ubuntu's behalf?
i know this sounds stupid but on my xubuntu i cant connect my laptop to a monitor it connects on bootup so i can see the startup but i cant change after. ive tried a lot of things and i googled it and searched but no answer i have xubuntu 8.04
I am trying to view my pc on my new flat screen but am unsure of the settings. I am using ubuntu 10.10. I have been trying (and on ocassion succesfully, but never really understood what I have done) to view my pc through the monitor option under preferences. Selecting the different monitor size but always find my external monitor (ie TV) is to the left, right above or under the screen I see on my PC. Also I am unable to hear my PC through the TV. I should say this is a good quality flat screen and all I am unsure of are the correct settings to use my TV as an external monitor.
