When I was trying to install debian stable in my laptop the process was freeze, I would like to know what was the problem, this is very important for me because the failed would be in a working server or on a project, so my questions are:
1. What are the places/files to look for errors? log files? dmesg? something else?
2. Are there some special commands or routines that can help in the analysis?
I've been tooling around in linux on and off since I discovered KNOPPIX 3.2. No linux distro has ever been a daily driver for me, though I wish sometimes it were.I've tried many distros over the past couple weeks via virtualBox on my mac and decided to install Debian on my laptop. I've tried multiple times and it has always failed; quite disappointing.
Laptop Specs;
HP Pavilion dv7 3169wm
64 bit AMD Turion II Ultra M620 2.50 GHz Dual-core
I started the install via the live ISO as the netinst & the DVD versions both failed, either by no suitable kernel or just flat out "installing base system failed". I've now found my computer to boot past the POST splash screen , and then to a black screen with a line cursor blinking with no input/output ability.To be clear, I did use uNetBootin to create the USB, and have successfully installed, and used multiple other distros (ubuntuMate, mint, peppermint, Arch, elementary) without issue, or at least nothing I couldn't fix.
How can I get past this and attempt to install Debian? I'd put my linux knowledge at a "beginner" stat, but I'm by no means daft about electronics and computers.
I just recently downloaded debian 8.2 live cd 64bit amd and wrote it to a usb stick with the universal usb installer from [URL] ..... The installer stops at the point of grabbing information from CD (right after choosing location) and since I have no dvd drive installed it spits an error out at me.
Now it seems to load the files right with the install icon from within the live mode but it gets cut off so I can't see about 1/3 the screens info. 4k monitor problems?
A bit of info, Installing on a Asus Maximus VIII Hero motherboard with ddr4, i7 6700k, win10 installed.
I'm rather new to UEFI bios options coming from a 2009/2010 x58 board, so I have a bit more reading to do.
Where to get working debian file that allows installation from the main initial boot menu.
Here is the message I get every time I try to install Debian Squeeze on my computer: Image at: [URL] I have tried multiple cd's and multiple iso's (and the iso's where all different) and the installation always fails at the same place. Here are my specs: Hardware Overview:
Model Name:Power Mac G5
Model Identifier:PowerMac7,3
Processor Name:PowerPC G5 (3.0)
Processor Speed:2 GHz
Number Of CPUs:2
L2 Cache (per CPU):512 KB
Memory:1.5 GB
Bus Speed:1 GHz
Boot ROM Version:5.2.4f1
I have recently upgraded 9.10 to 10.04 through the alternate CD. However, each time when I boot my system, post upgrade, I receive this error: INIT:failed to spawn spreadahead main process: unable to execute: No such file or directory After that it waits for a long time to show the desktop.
View 2 Replies View RelatedI just installed Maya 2009 on Fedora 13.It seemed to run the RPM install fine, but when I go to Applications > Graphics > MayaI an error:Could not launch 'Autodesk Maya 2009 (64-bit)
Failed to execute child process "/usr/autodesk/aya/bin/maya"(no such file or directory)I browsed to this location in the file browser and there definately is a file called maya in "bin"
HP Mini 210 x86_64
Fedora 15 latest upgrades
I was running
Code:
skype-2.2.0.25-fedora.i586.rpm
Which I downloaded from the skype website. This version worked fine. However, I did use it for a long time. I tried it last night and it didn't work. I got the following error:
Code:
Failed to lauch skype, failed to execute child process
[Code].....
I am trying to install eclipse via the synaptic package manager. The installation process failed and I tried manually as suggested
[Code]....
I have an Acer 9410Z laptop that I believe is running the Maverick Meerkat version of Ubuntu Studio. I just did an upgrade using Synaptic. I get to GRUB, but When I try to boot 2.6.35-22 (or the recovery mode or a real time kernel I had installed )I get the error:
INIT: Failed to spawn ureadahead main process. No such file or directory I then get the Ubuntu Studio splash screen for 2 seconds but then instead of a normal boot I end up in the terminal.
"(process:325): GLib-WARNING **: getpwuid_r(): failed due to unknown user id (0)"
It comes after choosing language, when the Ubuntu start-up logo shows with the 5 dut under it. I am trying to install Ubuntu Netbook on a little Compaq Mini.
I installed lilo and it boots. How do I installed grub again. Do I just use synaptic manager to uninstall lilo and install grub?
[code]....
I know grub2 does not work, giving me error: ntoskrnl.exe missing or corrupt. I did install grub-legacy and it worked, but I had to re-install squeeze due to other problems. So, now I want to replace lilo with grub legacy.
When I press )print screen button ) it says ....here was an error running gnome-screenshot:Failed to execute child process "gnome-screenshot" (No such file or directory)
View 4 Replies View Relatedi just tried to install Ubuntu Netbook 10.04 on my old Amilo Lifebook P Series. But after the boot screen and the choice to install Ubuntu i get stuck at the Ubuntu screen with the little dots on the bottom If I hit esc i can see the warning (process 257): GLib-WARNING **: getpwuid_(r) failed due to unknown user id (0)
View 2 Replies View RelatedI've been using Ubuntu since 6.04, not a linux guru by any means but can usually get myself out of trouble.
So, the issue... I installed 8.04 on my mother's laptop some time back as she was having trouble keeping Win 2000 running (she has a low spec no-name generic laptop btw). I live in Autsralia and she in England, i thought i could better support her if she was running Ubuntu... All has been well with 8.04 but with the new LTS release (10.04) i thought i'd talk her through the upgrade... Did the online upgrade via Update Manager, all seemed to go OK but when she went to log on after restart she got an error saying 'authentication failed' even though we are 100% sure we have the user name and password correct... Tried to do a ctrl+alt+F1 to by pass the GUI log on but couldn't get the terminal session to open up, just got a black screen - no command prompt.
So... thought OK re-install... downloaded the ISO, burned and sent her a CD in the post... talked her through the re-install, all seemed to go well (again) - BUT, after restart, couldn't log in "authentication failed" again...
So, remember i'm trying to talk a novice through all this... any thoughts!?!
If i can get her to log in i can then support her via some kind of remote sesion or other screen share... and it wont cost me a small fortune in international calls!!! But if i can't get a log in, i'm dead in the water!?
i'm installing debian using the netinstall option, the installation is freezed in the step: "retrieving file 811 of 811" like a 40 minutes ago it doesn't go on, so my question is:is there a command to know what is happen?, is there a command to know if the installation has some errors message?
View 1 Replies View Related- Press the <Enter> key to begin the installation processisolinux: Disk error 80, AX=42BA, drive 94Boot failed: press a key to retry
View 4 Replies View RelatedWhat are the differences if I build (./configure, make, make install) an app when log in as root vs a "regular" user other than I have to use sudo for make install? If an app is built from a non-root account, will it be available to every other user on the system?
View 4 Replies View Relatedwhile trying to install debian amd64 KDE, in the Detect Disks section, the process stops at: No disk drive was detected. If you know the name of the driver needed by your disk drive, you can select it from the list.
Driver needed for your disk drive: and gives a long list of drivers. my hard drives are Crucial C300 128GB.
i have no idea which driver on the list to pick so i can continue with install.
I'm trying to install gazebo and during the installation process, it complains that
Quote:
cannot find -lprofiler Sorry but can anybody help to explain
1) what is lprofile ?
2) which package should I install for this lprofile?
explain the following issue I have with Debian IA 64:I tried on a PC (Mobo Gigabyte G41M-ES2H, core 2 duo, 4 GB RAM DDR2) the live CD of Debian Lenny IA64 and everything worked just fine, which was a very good thing because none of all other major ia64/i386 distros of Linux (Mandrake, ubuntu, fedora) did so. In a nutshell it seems that the IGP G41 chipset is the cause of these setup failure (Everything is OK when using a PCI-e graphic card that I need in another computer)rd as someone (viewtopic.php?=17&t=49186&p=282839&hilit=G41M+ES2H#p282839) successfully installed Lenny on a very similar mobo. To go to the point what I do not understand is when I launch the iso Cd to now install the same version of Debian, everything freezes at the very beginning of the boot and the screen goes blank.
View 4 Replies View Related I downloaded a package from Debian's website with using wireless since I use a Macbook and currently I can only connect through wireless to get internet working. URLs....
When I try to open this with package install it gives me the following error:
Failed to install file..A unspecified transaction error has occurred. More information is available in the detailed report.
I'm starting to bump into crusty software in Lenny and am looking to upgrade to Squeeze. However, there's no release notes yet and Googling for upgrade directions yields all kinds of variations, some of which talk about "interesting" issue. Thus, my questions:
1. How hard/messy is the Lenny to Squeeze upgrade at this time?
2. Where can I find straightforward, clear directions on how to upgrade?
For quite some time, I just stayed on testing and incrementally upgraded on a regular basis, but stopped after Lenny came out because security support was suspended. Now I'd like to climb back on that train.FWIW, I originally installed Slink in 1999 and haven't reinstalled from scratch since, despite several generations of hardware upgrades.
How to locate usb devices before the process of installation?
View 2 Replies View RelatedI am in the process of installing BT4. At the partitioning stage of the install, I noticed that it could not detect my windows 7 like in the example screenshot they provided with the guide: click here: However, This is how the partition stage looks like on my system:
Why can't I see Windows here? I remember from the partition editor in windows, that my primary C: disk had 3 partitions. A system reserve, some small unallocated space and 157 gb which belongs to windows. My question is, why does it fail to detect the windows. I'm guessing the ubuntu installer only sees the 6gb of unallocated space as the only possible option to install on. So Ubuntu can only be installed on unallocated space ? I'll have to narrow down the partition that C: is on, make the unallocated partition bigger and put Ubuntu on it.
Did I answer my question there? I am being paranoid because in no case can I loose files. Here's a screenshot of my gParted
ran ubuntu tweak clean up on kernals and it failed to remove one. following this tried to search for updates and getting this error
[code]...
After downloading four .bz2 source files containing the sources for kdevelop-4.2.2, I tried to follow Soul Singin' HowTo without success apart from receiving this error:
edbarx@edbarx-pc2:~/kdev$ dpkg-buildpackage -rfakeroot -us -uc
dpkg-buildpackage: export CFLAGS from dpkg-buildflags (origin: vendor): -g -O2
dpkg-buildpackage: export CPPFLAGS from dpkg-buildflags (origin: vendor):
[code]....
What should I do to enable dpkg-buildpackage build the .deb package files for me? The /home/myuserhome/kdev directory contains these directories:
kdevelop-4.2.2.orig kdevelop-php-docs-1.2.2.orig
kdevelop-php-1.2.2.orig kdevplatform-1.2.2.orig
These .orig directories were created by dh_make --createorig, as dh_make alone grumbled that it needed --createorig.
I have tried to install some applications on my Debian Testing but I've got this common error after fetching packages from internet:
dpkg: warning: 'ldconfig' not found in PATH or not executable.
dpkg: warning: 'start-stop-daemon' not found in PATH or not executable.
dpkg: error: 2 expected programs not found in PATH or not executable.
Note: root's PATH should usually contain /usr/local/sbin, /usr/sbin and /sbin.
E: Sub-process /usr/bin/dpkg returned an error code (2)
I tried to install Debian 8.1 on Lenovo Edge 125, but on stage ''detecting network hardware' of install process my laptop stopped and froze, so I don't know what to do. (Previously I've installed Debian 6 or 7 on this laptop and every thing was OK).
View 6 Replies View RelatedI am trying to install Fedora 11 from a DVD. Not the live DVD, the full DVD and it hangs constantly. I had to wait 10 minutes for it to Find Storage Devices, 10 minutes to input a root password and now I am waiting for the drive shares to be setup. It's already been 10 minutes. I verified the disk and everything was fine. Why is this taking so long?
View 4 Replies View RelatedI'll have a Sony VAIO AR290 with 2 HDD, earlier I'll have a Windows XP and SUSE and RAID was turned off. Now I turn on RAID in STRIPE mode for better productivity, Windows 7 installation was successful, It creates MBR partition (100 M and C: HDD. During SUSE installation(I've chose all parameters- swap and partition) installation process stop at 1% on "operating with HDD" and my VAIO dont answer on any key pressed (alt ctr del, ctr c, esc) and I'll should to turn it power off. During surfing web, I'll find some solutions to solve it by creating root partition but It hasn't any results.
View 7 Replies View Related
