I can't seem to get my ethernet working properly. I've been having this problem since install and it's the last piece of hardware that doesn't seem to work properly. I know that the controller is being detect because of the following:
root@localhost:~# lspci -nn | grep -i ethernet
00:1f.6 Ethernet controller [0200]: Intel Corporation Device [8086:15b8] (rev 31)
I have an HP Pavillion Elite HPE computer I just got for a server. It has an internal gigabyte on the mother board and I put in one pci express trendnet teg-ectx eternet card in before installing. It is using the realtek 8169 chip. I had the local network on this card and the pubic static ip on the built in ethernet port eth0. After the intstall of debian 5.07 32 bit I couldn't get the eth0 pubic access to work. I can't get into the server with sftp or ssh and openssh has been installed and I can get into it locally on the local network.
I then installed a second ethernet card the same as the local network card. Now the pubic is on the which is eth1 and the local is eth2. I can ping out to [URL] but I can't get into the server on the eth1 using ssh and I have a iptables firewall and I turned it off and I stll can't get in. I am thinking that the eth1 card I added after the install doesn't have the driver or something. nothing is hooked up to eth0 right now.
[code]....
i just installed Red Hat 5 Enterprise Kernel ver: 2.6.18-8.el5Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controllerand i can't connect to the internet through the ethernet interface.I have configured manually the ip, netmask and gateway.
the ifconfig output is :
eth0 Link encap:Ethernet HWaddr 00:16:E6:5B:8B:56
inet addr:192.168.100.250 Bcast:192.168.100.255 Mask:255.255.255.0
[code]....
i was instelling ubuntu 8.10 on my laptop type HP (nx6110) but the Ethernet and the wireless are not work. i was used the nm-tool on terminal the code is
zaid@zaid-laptop:~$ nm-tool
NetworkManager Tool
State: disconnected
- Device: eth0 ----------------------------------------------------------------
Type: Wired
[Code]....
I have an Asrock A330GC, with onboard ethernet, and an Engenius PCI card for wifi.I installed ubuntu server 9.10 no problems, and it picked up my ethernet in the installation with no difficulties.I couldn't get 9.10 to do what i wanted, so I tried installing 8.4 instead. This however didn't pick up any of the drivers, so i couldn't get online.So i reinstalled 9.10, only to find that no couldn't find network in the installation.Absolutely NOTHING has changed, the ethernet cable still plugged in, and if i plug same cable into my laptop, it works fine.Any ideas people?ifconfig doesn't mention any eth0, just lo, with an ip of 127.0.0.1 and amask of 255.0.0.0 which i'm fairly certain means its dead
View 1 Replies View RelatedTell me how to configure my Ethernet card to work. My pc only works wirelessly. I don't know what kind of Ethernet card is installed. I have Ubuntu 10.4 on a dell pc 1ghz, 20ghd, 512mb.
View 2 Replies View RelatedIt was working just fine, until the other day I yanked it out. The wireless works just fine on the same router. If I login to a windows 7 instance on this dual boot laptop then the ehternet works just fine. So it's not a hardware, cable or router issue. The card even gets an ip, but I can't connect to the internet.
View 2 Replies View Relatedlaptop: averatec 6200 series
ethernet driver: SiS 900
wirless lan driver: rt2500
I got 10.04 installed and running pretty well.I cant get the wired ethernet to work but the wireless works. i did the the command line
[Code]...
also, dont know if i matters but ive got 8mbps/1.5mbps cable (motorala surfboard cable modem) and a linksys wrt54g wireless router.
I have a HP Mini running Ubuntu Desktop 10.04, and I cannot get a wired connection to work. My network card is "Broadcom Corporation BCM4312 802.11b/g (rev 01)", and I have the restricted drivers for the card installed. Wireless works fine, though.
My /etc/network/interfaces:
I have this tread, for a ASIX USB ethernet adapter. Still don't work.Tody i bought a Davicom DM9601 USB 10/100 EthernetI read here about this work out of the box, since 2.6.21 kernel. I have Linux Mint (Ubuntu 10.10) with 2.6.35-x kernol version; lsusb detect it; dmesg, detect it; at configure, automaticly get the MAC address, but just didn't work; with ping command, i get network is unreachable.
View 1 Replies View RelatedI have an old sony vaio laptop, and it has an intel 82801cam ethernet device and it refuses to work when I plug it in to an ethernet adapter. Im thinking it is a driver issues but whenever I list my hardware devices in terminal with lshw it seems to see that device despite that
View 1 Replies View RelatedI have 2 (some future machines will have 4) ethernet ports. I want to have them configured such that if any gets unplugged, as long as at least one of them is plugged in, it can reach the network (even if via a different IP address), and it can be reached (at least when trying a working IP address). I tried this for /etc/network/interfaces:
Code:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
[Code]...
I have had some problems with a SATA DVD drive under installation of Slackware 12.2, [URL] So i tried 13.1 instead. But now the ethernet card is not working Its a VIA Rhine card, and it was recognized just fine under 12.2 The following command did nothing: Code: ifconfig eth0 up I am getting no errors. I have also tried using netconfig, no luck there either.
View 3 Replies View RelatedWhen the ethernet cable is plugged in, it doesnt work. I have to unplug the cable, refresh the page and let it wait for the connection, after a second or two, i plug it back in, and it works. this works only for that page, which means only that page loads.. if i try to open another site or smthing else, it doesnt work and i have to repeat the exercise for the new site..i have to unplug, refresh and let it wait for connection and plug it back in.. The same thing happens if i try to download an application.. i have to first issue the command to download, and when it says "connecting to blah blah.." i plug the cable back in and it starts downloading, it doesnt work if the cable is already plugged it..!
View 9 Replies View RelatedI'm running Ubuntu 9.0.4 with an Intel PRO/100 VE Network Connection. I have been trying for a couple weeks now different techniques to get my wired ethernet connection working properly. I have a seeming common issue with my e100 driver dropping connection and having hard time picking it back up sometimes. I want to purchase a relatively inexpensive Ethernet card whose generic Linux driver actually operates it CORRECTLY, open up comp and put it in, and update to 9.10. Any list of Ethernet cards that are know to work flawlessly on Ubuntu, or at least tell me which card YOU are using that works perfect without having to write code, install wrapper programs, etc...?
View 8 Replies View RelatedIve been having some troubles with wireless. Ethernet works but wirless (at first) doesn't work. However, when i plug the ethernet in, all the wireless networks it detects are populated and i can then connect until i shutdown my computer.My disable internet button on my computer also doesn't seem to work well. It is always blue, and when i press it and have internet connection estabsliehd, it erratically turns from blue to orange to blue and then stays on blue.
When i have shutdown and booted up and i haven't placed ethernet in (so wireless doesn't work) it wont even change color.Any solutions? I dont know what info to include so just let me know and when the wireless does it work, it is slow in opening a new tab and connecting to google.
installing ndiswrapper. I've used Windows all my life and I just made the jump to Ubuntu a couple days ago, install native drivers for my card, but at the end of the list of like 25 packages there are 4 packages that won't install because they all say they have dependencies upon each other. Now, I'm trying ndiswrapper and I don't understand it in the least little bit... I know I'm an utter noob, but the OS seems amazing, I'd just like to connect to the internet with it. Even the ethernet port doesn't work! :/
View 1 Replies View RelatedI installed UBUNTU 10.10 alongside windows 7. Now the problem is: If i boot into UBUNTU first, ethernet does not work. But it works if i boot windows first and restart back into UBUNTU. Which means i have to boot windows first to make ethernet work on UBUNTU every time i start my PC.
View 9 Replies View RelatedI have installed Ubuntu 11.04 using Wubi through Windows 7. It seems to be working but it will not connect to my wired internet connection. It tells me there is no wired connection, when there is. I used sysinfo and its not showing any network adapter or controller. I have a board with nvidia nforce go 430, could it be a driver issue. It works fine in windows though. Tried using a wireless adapter and all is working. But why doesn't the wired ethernet connection work.
View 9 Replies View RelatedI just installed Fedora 10 on a brand new machine with an on-board nvidia MCP73 ethernet card. Now, when I initially boot up the box after installation, the card comes up and gets a DHCP address just fine. When I go to edit the network settings (change to static) the NIC dies. I don't think I have the proper driver. Does anyone know a) where to get the driver and b) how I can install it?
[code]...
I'm currently running Fedora 13, after I updated the kernel to 2.6.34, I have to run (as a superuser) "service NetworkManager start" in order to start my network manager, is there are way I can run this on startup?
Also my ethernet connection seems to only work when I restart/boot up my computer, when I wake my computer up from being asleep, the ethernet stops working.
I changed a mainboard so the network card is RTL8111/8168B Gigabit now. By "ifconfig -a", there is only io, no eth0.
I got a driver r8168.ko from: [URL]
After I insert the r8168.ko, there is eth0. Run "/etc/init.d/network restart", it reports "Determing IP information for eth0... failed; no link present, Check Cable", and I noticed the lights of network card and runter are all off. I can use "ifconfig eth0" now but it cannot connect to other machine.
It's Gigabit card and my runter is 10/100M. I tried "#insmod r8168 speed=100 duplex=1 autoneg=1" and "#insmod r8168 speed=100 duplex=0 autoneg=1", it can not get IP by DHCP either. I also build the .ko from Realteck source code, the behavior is the same.
if I need to do other configurations?
My CentOS is CentOS5, 2.6.18-8.el5 #1 SMP.
== BEGIN uname -rmi ==
2.6.18-8.el5 i686 i386
== END uname -rmi ==
== BEGIN rpm -q centos-release ==
[Code].....
I'm a new user of Ubuntu, so i'm not that familiar with this OS. My wireless network is detected but when I'm entering my 128 bits WEP key, it doesn't connect at all. I have no clue where to start troubleshooting.
Here's some of my specs if that's of any help:
Computer is a Sony Vaio laptop model VGN-SZ370P
My wireless card is from Intel Corporation 82801G (ICH7 Family) USB UHCI Controller
The ethernet cable connection used to work before, but I fooled around with some commands and now seems to be disabled...
I have a Zotac Ionitx A-U. I can't get it to establish an internet connection with the wired ethernet within Ubuntu. The chip is detected, but trying to bring up the connection stalls out at trying to obtain a DHCP lease, like this:
DHCP DISCOVER ...
DHCP DISCOVER ...
No DHCPOFFERS received
Specs:
Ionitx A-U
Ubuntu 10.04 x64 kernel 2.6.32-22 (also didn't work in 9.10)
[Code]...
By upgrading to latest kernel(2.6.31-22) the card was recognized but it still doesn't quite work. I'm not that good at this but I'll paste some stuff that I think is related to solving a problem such as this.
[code]...
I have a Dell WLAN 1397 Half Minicard, 802.11 b/g card in my laptop, and I can't seem to get ubuntu to work with it. I tried this method:
1. Synaptic Pack Manager
2. Check "Install from Boot Disc"
3. Reload
4. Install and apply bcmwl-kernel-source
5. Reboot
This didn't work for me, so I tried entering sudo apt-get install bcmwl-kernel-source and that also didn't work. Another thing I tried is formatting my Ubuntu partition and reinstalling, and retrying both of those methods. The ethernet port does work, however.
I just installed Ubuntu 10.04 on my Powerbook G4 1.5ghz 15", and the ethernet port on the laptop doesn't work. So I can't search for drivers to install.
Is there a way to either tether internet to the laptop using firewire? find the necessary drivers so I can transfer them?
Centos 5.2 Asus Eee box with Atom N270 and it came installed with "eLinux" which doesn't even come close to meeting my needs (low demand intranet server). But eLinux did work as far as I tested it.
First, CentOS seems to detect the Intel 945GME video chip but I end up with a blank screen. I used text mode to install CentOS. Then I searched for a solution. Found someone suggested also using the i915 driver with 945GM. That didn't work.
So, I reverted to a VESA driver. That worked except I couldn't get resolution greater than 800x600 even after I added a Mode line for 1024x768 to the xorg.conf file. However, the X interface wasn't that important. I mostly wanted into the utilities so I could fix the network.
I had tried a fixed address (192.168.1.11) since the box is supposed to be a "thin server." No luck. So, I tried DNS and tried activating again. The suggestion was that the network cable wasn't connected. When using DNS, the network hub lights flash. Something is happening.
Rebooted the computer using Puppy Linux (on a usb key). Video comes up in VESA mode. I can set it to 1024x768. It found the DNS server without any complaints. (Note: I didn't so much as touch the ethernet cable during the reboot).
Copying and Pasting isn't easy with a computer that won't connect to the LAN. But the hardware is a Realtek RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 2). I since tried Slackware 12.1 and it's pretty happy on that box. Vesa mode gets me 1024x768 and the ethernet works (however it thinks it's on eth1 which may or may not be a clue). I'll try CentOS on an old box for other testing.
I just performed a fresh install of Suse 11.4. It worked great except that the network communication would cut in and out intermittently. I managed to solve the problem posting it here for other users and for future suse releases. I will give the hardware I am running, the symptoms and the fix:
Hardware
=======
Motherboard: Gigabyte GA-H67MA-UD2H-B3
Ethernet controller: Realtek RTL8111E
Default module: r8169 (run lsmod to see loaded modules)
[Code].....
1) First make sure that linux kernel source is installed in your system (yast software management)
2) ensure that gcc is installed (yast software management)
3) Download the latest linux driver for RTL8111E from the realtek website The one that I am running is the 8168 driver version 8.024.00
4) unzip the tarball (creates a directory called "r8168-x.xxx.xx")
5) As root run the autorun.sh from inside the newly created "r8168-x.xxx.xx" directory
I've recently bought a recycled computer for my office. The plan was to get an old cheap computer and use it to write LaTex documents but nothing else. However, I can't seem to get the thing to connect to the internet. I'm on a University network which has a funny setup but I don't think that's the problem.So here's the deal. I have tried this with 9.04, 10.04 and 10.10 and it hasn't worked. The computer recognizes the ethernet cable. If I issue the command "sudo mii-tool eth0" and get back "eth0: negotiated 100baseTx-FD, link ok". However, click on the networking logo on the top right, and click auto eth0, it tries to connect for about 30 seconds, then gives up. Unfortunately I'm pretty clueless when it comes to networking so I have no idea what to do to try to fix this.
View 8 Replies View Related