Debian :: 8.1 Second Monitor Is Detected But Only Showing Black Screen
Jul 30, 2015
I've recently installed Debian v8.1 and installed Nvidia driver 340.46. In nvidia-settings I am able to enable my second monitor and enable it/set it's position..etc. My second monitor is not being detected in Debian Display and is 'on' but only showing a black screen. I've tried researching and implementing various 'fixes', but I'm not having any luck.
I'm running dual GTX 570's with a monitor plugged into one each (DVI). I noticed in my xorg.conf under Section "Screen" I have an option "MultiGPU" "Off"; would this be part of the issue?
I've tried:
- purging all nvidia drivers and re-installing
- installing different versions of nvidia drivers
- add nomodeset in grub
View 2 Replies
ADVERTISEMENT
Apr 19, 2015
I have a laptop and an external monitor connected via displayport. I can configure both displays via settings with correct resolution and arrangement. However, this configuration is not sticking, and every time I shut down the laptop or close the lid I will need to fight with black screens and more to bring the same configuration again. Basically, it seems that the monitor is "stealing" the primary role to the laptop's native screen (I have it configured as secondary, but also being primary the configuration gets messed).
After many trial & errors, this is the routine I have found to make things work every time I boot / awake the system:
1. Boot. Laptop's display shows the booting sequence.
2. When the login screen should appear, laptop's display goes black, monitor shows background.
3. If I press F9 to increase brightness, the brightness icon appears in the monitor, but it is stuck at the minimum.
4. The only way to leave this point is by pressing F7 (project screen) and then F9 again to increase brightness. Then the laptop's screen does light up.
This is when I'm lucky. Sometimes the configuration goes mad and I get mirrored displays and different resolutions, without touching the settings myself. Also, if I unplug the displayport I run the risk of getting stuck with a black screen in the laptop, without any way of recovering the GUI other than rebooting (Ctrl Alt F2 will still show the command line screen).
My system is Debian 8 testing up to date, running in a Lenovo T430 with Intel components. I'm not sure the monitor is relevant here, but in any case it is an Eizo CS240.
View 3 Replies
View Related
Aug 7, 2011
I am having problems getting my external monitor to work. When I plug in the monitor, both the laptop screen and the external monitor go black. When I unplug the monitor, the laptop screen works again.
When I startup with the external monitor plugged in, neither screen works or teh computer hangs or something.
I have had the external monitor going on a couple of occasions. I did manage to configure my monitors through System Settings > Display. I turned off the laptop monitor as I just want to use the external. But after rebooting, things didn't work.
I have a Thinkpad E420, Fedora 15
View 14 Replies
View Related
Feb 5, 2011
I have openSUSE 11.3 with an nvidia card connected with two monitors. In the past I used xinerama which was ok, but now I need to have two separate desktops, one on each screen. I set the nvidia driver with x screen, and now one screen works perfect and the other only shows a black screen. When I move the mouse over the black screen, the mouse pointer turns into an X, but moves correctly, which seems to me that the problem is that I need to set the second desktop to that screen. I looked on forums on how to do so, and no luck.
View 1 Replies
View Related
Nov 30, 2010
I have Ubuntu 10.04 running kernel .26 installed on my Dell Dimension 2350 with 512mb of memory. The problem I have been having is, When I am using the computer mostly Internet stuff for no reason the monitor will go black then on the screen it will be at a terminal screen, kind of like when you start up the computer, I don't remember what is all on it but the last thing in the list was: checking battery state: OK after that the screen will flash in multiple colors and then it goes into a loop of just black screen than a colorful flash and back over to a black screen. the only way I can fix that is by holding down the power button. this will happen mostly on face-book on the games and just on the profile page, but it does happen just checking my gmail or play solitaire it does this around 4-8 times a day.
View 3 Replies
View Related
Sep 8, 2010
Every time me or another user uses the "log out" option were faced with a black screen that does not go away, unless the computer is restarted. i've left it for an hour thinking it might have just slowed down or something but that was a no go, and it happens each time you try to use it. the strange thing is if the black screen is up programs still run. i have a media server running most of the time and i have no problem accessing it while the black screen is showing.
Another problem im having is that sometimes when a user logs in they have no sound. the sound icon is showing that no sound is installed, but when another user logs in there is no problem and sound works fine.
Lastly i dont know if this is a feature or a problem. the first user to log in will always have control over the network connection. for example if my mother logs in first the icon to switch connections will show up on the top of her screen and she has full access to what connections she wants to use, also her account is just a basic user account. now when i log in i wont have the network icon on the top of my screen, and my account is the main admin account.
View 3 Replies
View Related
Jan 9, 2011
I installed some weeks ago Fedora 14 via burnt iso file downloaded from official Fedora site. It was working perfectly like a charm for me until yesterday when I tried to install zend server for PHP.During my first try of installation of zend server it corrupted out my apache server and I lost apache on http://localhost.I removed all "zend-server" like stuff from "Add Remove Software" screen.
Installed again apache 2 in the form of LAMP (Linux Apache Mysql Php)via terminal. Apache installed correctly and started workeing again ok on localhost.n again I tried to install zend server from install.sh file in downloaded zend server installation. It showed me after a while like "zend server installed successfully".I shut down my pc thinking everything is ok now.
Today when I started my system, it shows me boot screen of Fedora, I select fedora and then it shows me baloon filling up for around 5-7 secs. Then all of a sudden a black screen appears up with a cursor blinking at its top left and then nothing else happens further. I cannot find login screen to my desktop anymore.I remember one thing thating reinstallation of apache from terminal, I set following command like "chkconfig --level 235 httpd" (I guess that's what I have written as per some online tutorial for LAMP). Is that cause of mine problem ot its something else?
View 6 Replies
View Related
Apr 18, 2011
when I boot and login to a fresh install of Ubuntu, everything goes fine, the login screen appears, I login. Then the cursor appears on a black screen. This is normal. Then when the desktop should appear, on the very left edge of the screen, about 5 pixels in size, you can see the panel and the rest of the desktop. But I stress, You still see the cursor. In this small area, you can right click as you, even click on the menu and it will come down, you can see it. I can click on Ubuntu SC and the cursor will turn to a loading symbol. But then nothing again. I can press Ctrl + Alt + F2 and terminal will come on fine. So far, this has happened on a live CD of Maverick, A live USB of Maverick, A Natty Narwhal Fresh Install, A Maverick Fresh install, A Karmic Old Install and That same Karmic After going through a Distro upgrade via Ctrl + Alt + F2 to 11.04. I've gotten all the updates for all of them (A slow, bandwidth wasting process), and this doen't happen on other computers, even ones with lower graphics cards then mine. Additionally, on the same computer on a seperate partion, I can load my main Maverick just fine, Indicateing that it can't be a hardware problem. After searching across the internet, I'm at loss to an answer.
View 4 Replies
View Related
Apr 14, 2011
I could upgrade openSUSE 11.4 on my desktop but when trying to do the same procedure on my girlfriend's laptop, after the zypper update part (and the reboot asked), now we can get it to boot.
After selecting suse from GRUB it shows some code (too fast to be read) then black screen forever. I erased the VGA option before booting and now it gets stuck in
Code:
[0.490266][<c02037a6>] kernel_thread_helper+0x6/0x10
We don't have any idea of what to do ;__;
View 5 Replies
View Related
Mar 8, 2011
I have a problem with booting from a USB flash drive. I have Acer TimelineX 3820TG. I have Windows 7 Home from Acer and I installed Mandriva OS from USB(from USB because this Acer doen't have a DVD drive). It was OK, but I want reinstall Windows 7 and so I did. Now I have Windows 7 Professional and it wrote over Mandriva's GRUB. It wasn't a big problem. For a while I was just using Windows 7 but now I am thinking that I need some OS with Linux and I am thinking about Ubuntu. But when I tried to boot from USB with Ubuntu I get a black screen with a blinking cursor after the BIOS POST.
I was trying many applications to create a bootable USB drive and many versions of Ubuntu (and other Linux distributions), but nothing worked. I tried to Google for answers but I found many problems where all booting goes to black screen but in my problem Windows 7 boots fine from disc but from USB doesn't work.
View 1 Replies
View Related
Mar 28, 2011
one of them is a TV with an HDMI input. The login screen shows up on the tv, so if someone is watching a movie, I have to pause it to switch inputs and login. Other than that, everything is fine. How do I get the login screen to show up on the main monitor?
View 1 Replies
View Related
Jan 18, 2010
OS: Fedora 12
Video card: ATI Radeon 9200 series
Monitor: ViewSonic 19"
I installed Fedora 12 configured Gnome automatically. Generally default settings. My monitor was connected directly to the video card and all was good. My video card was detected and my monitor was detected as ViewSonic Corporation 19" and I can set the screen resolution to 1280x1024. I had no xorg.conf file, as it seems that Fedora 12 does a great job of PnP to just set everything up.Now I go and complicate things by hooking up my monitor through a KVM switch. All of a sudden my monitor is "Unknown" and the best resolution I can achieve is 800x600.
Sure, I could go and reconnect without the KVM, but I want to be able use it.Is it possible to edit xorg.conf to tell it "Trust me, just use 1280x1024 at 60Hz even though you can't figure out what the monitor is"?
I tried a number of the posted suggestions to generate xorg.conf files but none of them get me what I need. A simple sample file listing that does the minimum is greatly appreciated (I can experiment from there once I get a basic setup working).And can someone explain if it is X or the ATI driver that is getting confused by the unknown monitor type. It helps to know what is actually going on in addition to a fix (so I can figure it out myself in the future). Thanks!
View 3 Replies
View Related
Mar 6, 2010
i tried to install linux mint, at first i got 'out of range' with black screen msg but used compability mode and got past it and installed mint on my HD. a moment after it updated my nvidia drivers and after reboot I got the out of range message again, which leaves me in the situation where i cant do pretty much anything I tried editing xorg.conf added VertRefresh 60-75 and Modes "1440x900_75.00"
View 4 Replies
View Related
Mar 23, 2010
I have an Intel Corporation Mobile 945GM chipset. As I was playing around, trying to figure out how to get my dual monitor to work. The Mirror Screen was working fine, but then I uncheck the mirror screen option, both my laptop and my secondary monitor black out. I can only see the mouse, and it cans move on both screen.
Here is my xorg.conf:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
[code]....
View 3 Replies
View Related
Jul 2, 2009
I have this very frustrating problem... I'm trying to build a Linux-based HTPC (Home Theatre PC). I'm running Ubuntu 9.04 Jaunty as the operating system, and it works fine when I have it connected to my 17" Samsung monitor. However, when I connect the HTPC to the TV via VGA I get a black screen after "startx" (I can access the console through recovery mode though). Ubuntu is running gnome, so I guess it's a gnome related problem?
I would have thought it was a problem with the drivers to graphics card, but since it's working on my 17" monitor I've ruled that out. The TVs resolution is 1024x768. What can be causing this? Apperently there's some difference between my monitor and my TV (forgetting the fact that it is indeed a TV, not a monitor), but what? I've previously run Windows on the same hardware without problems, and thought I should give Linux a shot. It doesn't look good...
View 14 Replies
View Related
Feb 19, 2009
I install the debian on my PC, but the monitor is not detected or not adapted ( while it is for linux CD live, and windows XP). it gives the following errors :
I want to use the file xorg.conf given by CDlive ( sidux for example) and copy it in the /etc/X11 of my debian, is it enougn or I need ohter configuration ?
View 2 Replies
View Related
Jun 18, 2011
I am booting XP and Opensuse 11.4 all was ok until I changed my old monitor for a widescreen monitor, Xp works ok but when I select Opensuse from the menu it just boots to a black screen.
View 3 Replies
View Related
Nov 30, 2010
I did a LiveCD to USB install, following the directions I found at [url] When I went to reboot to the USB stick, all I get is a black Screen (monitor is on and lit, just nothing on the display) No cursor or command prompt. I've tried holding shift to bring up the GRUB menu, changing splash quiet to nomodeset, or just adding nomodeset after the splash quiet thing. I've even tried xforcevesa instead of nomodeset still black screen. Looking at the logs nothing is current as of the last time I tried to boot the computer, it's strictly what was written when I installed it to the stick. Other things I've checked/tried, Pressing CTRL+Alt+F1 at GRUB to get TTY, all I get is that blank screen. I've Checked etc/default/grub to ensure the timeout was higher then 0. The Install CD seems to be OK but I have (as it did another install successfully) but I haven't done any throughal checking of it (there was no check this disk on the first screen of the LiveCD) The USB sticks also seem to be ok (in windows though). Using the disk utility on the live CD I did check the file system on the USB stick, the "/" partition came up clean. Anybody have any other thoughts on this install, any thing else I can check?
View 9 Replies
View Related
Sep 29, 2015
Today I set up the energy settings like that:
10 minutes (screen), 20 minutes for suspension.
After around 30 minutes, I came back and switched back on the pc.
The primary monitor (VGA) was not detected, even after a system reboot.
More info about my pc:
Debian stable 8.2, kernel 3.16.0-4-686-pae.
I have an Nvidia card, but currently I am using nouveau drivers.
Two monitors: VGA (primary) and DVI (secondary).
Later I could get my primary monitor to work by switching tty (ctrl+alt+f3 and typing "startx" in the console).
I guess this is related to Xorg configuration (/etc/X11/xorg.conf is empty), but I am not really sure.
View 2 Replies
View Related
Apr 3, 2011
Just did a fresh install of Natty B1 (previously had alpha 2).. I noticed this issue w/ A2, as well.. plugging in the exterminal monitor (via mini-displayport-to-vga connector) will do the following:
1) turn the screen on the laptop's display entirely black (but not turn it off).. i can move and see the mouse cursor.. but everything on the window appears to not rending or "painted" black..
2) external monitor never becomes active..
the only way to recover is to kill/restart X or reboot after disconnecting the extmon.. having extmon plugged in from boot produces the same results (and it doesn't seem to ever become active during boot up). sometimes this won't happen right away if i plug in the external monitor.. but opening the Monitors system prefs dialog will definitely cause (or detect displays) ,etc I waited to see if the issue would fix itself w/ the beta update, but it hasn't.. Any other 8,1 owners out there that can verify this issue? My (totally uninformed) guess is that it's due to differences in the display/gfx hardware and thunderbolt integration(?)
(I've seen a verification verifications of working-out-of-the-box.. but they were from 8,2 and 8,3 owners (which have discrete graphics cards))... If anyone's gotten this to work with some config stuff, I'd love to see that as well (since the wiki page for 8,1 says it works ootb). If someone could let me know where I should look to capture error output when the above issue occurs, that would be awesome.
View 4 Replies
View Related
Jul 13, 2011
I have just "finished" updating my Ubuntu 9.10. (somehow I knew that something is going to go wrong), and now my PC starts, works fine for a few seconds, then I get a black screen for a moment, and then my monitor starts acting like PC is off.Interestingly I think that otherwise everything is working just fine and that I just can't see anything due to the black screen (monitor is flashing like there is no signal coming from PC).
View 3 Replies
View Related
Nov 13, 2015
I noticed that Debian 8 has a significant bug related to detecting presence of display(s). Today, I woke my computer from sleep while the LCD monitor was unplugged from power (the monitor is connected via DVI) then I powered the monitor but nothing was displayed. Next, I connected another monitor via HDMI and both screens started working. However after disconnecting HDMI cable from the second monitor the first one with DVI stopped showing anything. The conclusion of this situation is that HDMI monitor must be connected all the time.
I thought that this is caused by graphics driver, but I experienced the problem on different machines, one with nvidia driver and DVI, and the second with default free driver and DisplayPort.
I just checked that this is related to KDE. After switching to console using ctrl+alt+f1 the screen turns on, but when I am going back via ctrl+alt+f7 the screen disappears.
View 2 Replies
View Related
Aug 16, 2015
Setup:
I'm using i386 Jessie Debian, have an i7 Intel processor and Gtx 745 4gb NVidia GPU.
I am running with nomodeset due to blurring issue but issue occured without nomodeset too.
Problem:
When I start Debian with just a monitor in the HDMI slot it doesn't recognize the monitor and keeps the monitor at 1024x768.
When I start Debian with monitor in both DVI and HDMI slot it only activates the DVI monitor (with proper resolution). PC has no VGA I have no DP cable.
xrandr:
xrandr: Failed to get size of gamma for output default
Screen 0: minimum 640 x 480, current 1920 x 1080, maximum 1920 x 1080
default connected primary 1920x1080+0+0 0mm x 0mm
1920x1080 0.00*
1280x1024 0.00
1024x768 0.00
800x600 0.00
640x480 0.00
Which is my dvi monitor, no other screens detected. Is there any way to get the HDMI to run properly?
View 1 Replies
View Related
Oct 20, 2015
My system can't seem to detect the external monitor that I've plugged into my laptop using and HDMI cable. The monitor works when I'm booted into Windows so I know that it isn't a problem with the monitor or the cable.
When I run xrandr I get.
Code: Select allScreen 0: minimum 320 x 200, current 1600 x 900, maximum 8192 x 8192
LVDS1 connected primary 1600x900+0+0 (normal left inverted right x axis y axis) 310mm x 174mm
1600x900 60.00*+ 39.99
1440x900 59.89
1360x768 59.80 59.96
1152x864 60.00
1024x768 60.00
800x600 60.32 56.25
640x480 59.94
VGA1 disconnected (normal left inverted right x axis y axis)
HDMI1 disconnected (normal left inverted right x axis y axis)
DP1 disconnected (normal left inverted right x axis y axis)
View 4 Replies
View Related
Nov 14, 2010
on a 6-7 years old compaq laptop, connected to a brand new hp monitor i am having a mismatch with computer/monitor resolution.
before i had ubuntu 10.04 which could only run in x's safe graphics mode - allowing for full screen resolution but with handicapped graphics - for example videos fullscreen would be quirky and run with cpu at 100%, something which was no problem before 10.04.
then i tried ubuntu 10.10 and later lubuntu 10.10 (which had exactly the same problem); the monitor is running 1440x900 while the computer is rendering to only 1024x768 - leaving a huge black border on right and bottom of screen. the gfx is still crippled; videos fullscreen is quirky as before.
View 3 Replies
View Related
Nov 30, 2009
I'm a newbie to installing LINUX (was an Oracle DBA for many years) and I am having trouble getting the dual head function to work with my Sony Vaio laptop. I just select a generic LCD with the screen resolution that I want, but when I startx, I briefly get the login window (terminal), then everything goes blank and I have to unplus the samsung monitor and reboot to be able to have a screen again. I have tried the fn + f keys and that doesn't help.
Here is the hardware:
Samsung Syncmaster 2343BWX
Sony Vaio VGN-FJ170
Intel Graphics Mobile 915GM/GMS/910 GML Express graphics controller
I would like to use this laptop as:
Audio streaming from internet (so far not working on my local NPR stations)
Hooked up to KVM switch - using the Samsun monitor and an adesso integrated keyboard
Wireless network (that is working - but it took some doing....)
What files and logs I need to post I will do so, but if what I want to do is just not possible or a big hassle, please just let me know, and I will load windows. Although I really wanted one LINUX box in my home office.
View 1 Replies
View Related
Jan 16, 2010
I have an Asus z9100 laptop with an Intel 855GM integrated graphics chip, which is running Karmic (the purpose of the laptop is to be a MythTV frontend so my understanding is that it needs to run 9.x in order to connect to the MythTV 0.22 backend - I have installed and configured this using the installable Mythbuntu package) and the laptop is subject to this bug which causes random freezes:
[URL]
So, following advice for similar freezes I've seen, I have added the following options to my grub menu.lst on the kernel line:
nolapic nomodeset
and I have edited xorg.conf so that it makes use of the vesa driver instead of the Intel driver. This results in no freezes and if I wanted to watch Myth on the laptop screen I'd be squared away. However, the laptop has a damaged screen so the point was always to output the signal to an external monitor via its VGA out.
When I attach the external monitor and boot with the setup as described, the external monitor is never detected. But I noticed that if I remove the "nolapic nomodeset" from the kernel boot line, it is detected. However, signal is only output to it during the earliest part of boot (when the Ubuntu logo is in the center of the screen before the full-screen graphic with the animated progress line), after which the external monitor goes black and all the display output goes to the laptop screen. The external monitor power button is still lit up green as if it has been detected and is receiving signal, but it's just a black screen.
get the signal out to the external monitor after the initial part of the boot process, using the vesa driver? Here is the current state of my xorg.conf:
Code:
Section "Device"
Identifier "Configured Video Device"
Driver "vesa"
EndSection
[Code].....
View 2 Replies
View Related
Feb 26, 2010
I've been running openSuse 11.2 for a while on my notebook.Today I turned it off at work and came home. When I tried to turn it on, it boots, shows a black screen written 'GRUB' and then NOTHING. It doesn't complete the boot process.
View 9 Replies
View Related
Apr 26, 2011
I have tried loading 11.4 from the DVD from Linux Magazine. Everything goes swimmingly until I get to using it when the screen shows black rectangles, is "twitchy" and nothing works properly. I currently run 11.3 which works fine.
View 3 Replies
View Related
May 5, 2010
I cannot install Ubuntu 10.04, or even boot into the live CD. I'm not an expert, but I've used Ubuntu for several years, and I'm pretty sure I'm not doing anything stupid... Here's what happens when I boot with the Ubuntu 10.04 live CD: I get a purple screen with just an accessibility(?) symbol at the bottom (this lasts 15 seconds). The screen goes black, with a flashing cursor, then changes back to purple, this time with an Ubuntu logo, with 5 dots acting as a progress indicator (this lasts about 1 minute). The screen switches to standby. The CD drive continues to make noises for another minute or so, then stops.
I physically removed my graphics card (ATI Radeon HD 5770), and plugged the monitor straight into the VGA port on the motherboard. Now the CD boots up fine. I could try installing Ubuntu at this point, while my graphics card is unplugged, and then plug my graphics card back in, and see if it starts working then.
View 9 Replies
View Related
