I installed the VSFTPD from YUM and installed the webmin module.i can connect to the server with Telnet but can�t list files.When i try to connect with a FTP client i get the following errors: An error occured openig that folder on the ftp server. Make sure you have access to that folder.
200 Switching to ASCII mode.
227 Entering passive mode (172,20,1,5,69,210)
How to i choose Users and what folders to use??
My old Creative Zen MP3 player has just gone titsup - it's gone into recovery mode and attempts to reload the firmware come up with device not connected errors (even under Windoze XP) So I'm looking around for a replacement and the Cowon D2 looks good as it takes SD cards like the zen (and I'd just bought 2 new 8Gb cards). The Zen used mtpfs which worked under linux but not well an I believe the D2 just connects as USB memory. Anyone out there using a Cowon D2 under Linux?
View 1 Replies View RelatedI have a problem with getting my fedora 14 laptop to connect to my fedora 12 server that is hosting my smb HP Deskjet 5650 printer. The error that I get is the following: CUPS server error. There was an error during the CUPS operation: 'client-error-not-possible'.
I have been able to get my daughters Ubuntu laptop and my wife's Windows XP laptop to connect and print without a problem.
I've got a problem occurring with my openSUSE 11.3 // GNOME Empathy Chat Client. When I try to connect to my Facebook account, my client tells me that I have a Network Error. Last time I used the client at home, it worked perfectly fine, but when I'm at work it doesn't.
Now, you guys may say that my work's network may have ports blocked, or the firewall is blocking its use in some way, but I find that hard to believe. My reasoning? I am able to connect to my Facebook account thru Empathy at work on my previous Ubuntu 10.04 system with no problems. I have also been connected to the same chat accounts this whole week on my openSUSE 11.3 // KDE 4.4 Kopete chat client.My Empathy connects to my Skype with no problem also. So, do any of you have any ideas that could possibly solve my issue? I love being connected to my Facebook chat at work because I don't see anyone nearly as often, and it's a great way for me to keep in touch with them.
I apologize in advance if the following problems I am facing seem 'basic'.I am a newbie to Unix systems and trying to learn and adapt. I am trying to install fred-client-2.2.3 on Ubuntu 8.04 - the Hardy Heron.
So I first downloaded the .tar.gz file from
http://fred.nic.cz/sources/fred-client-2.2.3.tar.gz
Then using the terminal I entered:
tar -xf Fred-Client-2.2.3.tar.gz
cd Fred-Client-2.2.3
sudo ./install.sh
[Cde]..
My problem is to get postfix working with a smarthost, to send mails from home with dynamic IP, and which needs authentication. I did exactly the same with Slackware 12.2 (postfix 2.6.2) and it worked. Now I tried to do with 2.6.2 (actual running version is 2.7.0 with the same problem) on Slackware 13 64bit. Following error message occurs around every minute in the maillog:
[code]...
I try to set up a 5 nodes cluster and a shared Coraid Storage with conga but it fails with "Shared Storage Support" checked.The message is:'A problem occurred when installing packages: Packages of set "Clustered Storage" are not present in available repository' and it is shown under every node on the next sceen after I submit.The pc where conga runs is on the same subnet (192.168.xxx.xxx) and it has the same /etc/hosts of the other nodes.In that pc runs a proxy too and the nodes go out through it (that pc has 2 NICs)Every node (2.6.18-128.1.14.el5-xen-x86_64) is patched whith the last yum update (this morning) the same is for the pc (2.6.18-128.1.14.el5).Every node has 4 NICs , 2 NICc towards the storage the others in bonding towards the WAN.Every node is exactly alike, they have been installed with the ks.cfg generated from the first node and they all have the support for Clustering, Virtualization, and Clustered Storage.
View 1 Replies View RelatedThis will be a little long (having read Phil's 'how to ask questions' FAQ). I'm trying to get OpenVPN working between my CentOS server and some Windoze laptops running XP. There seems to be plenty of sample
config files available, but to date, none of them have worked for me. Pulling out my trusty Wireshark, I've found some clues,
BACKGROUND:
My local subnet (NAT'ed by my gateway router) is 192.168.52.x. My router has been configured with a conduit (port-forward) for port 1194 (the standard OpenVPN port), which points towards my CentOS server.The CentOS server is .52.112, and the supplicant is .52.110. I have tried the lient both inside and outside my local subnet, with no difference in events or outcomes.
[Code]...
I've tried to read many of the topics in this forum first and tried to find a solution to my problem, but can't find one.I'm testing CentOS 5.5, it's the first time I'm using a CentOS Linux release.I'm trying to configure the proxy "client side " on it and cannot find how to do it.On other Linux release I've used the ENV variable like "http_proxy" or "HTTP_PROXY" etc etc.This time, I don't know why but it doesn't work.I've put the name and @ip of the proxy in /etc/hosts and tried different version upper/lowercase of "http_proxy" "HTTP_proxy" "ftp_pr.." but it doesn't work.If I configure manually Firefox and puting the name or @ip of the proxy we have on our network, it works.But if I try to use ENV variable it doesn't work...
View 1 Replies View Relatedwhen i typed command /usr/sbin/amcheck intra on client side i got following error.(expecting a new tape)
NOTE: info dir /var/log/amanda/intra/curinfo: does not exist
NOTE: it will be created on the next run.
NOTE: index dir /var/log/amanda/intra/index: does not exist
NOTE: it will be created on the next run.
I am using centos 5.4, recently i come to know that people are'nt able to connect to my system using ssh.1. but i can easily connect to them. 2. I checked the firewall settings also, it seems ok to me.3. I tried restarting sshd also. " /etc/init.d/sshd restart " but to no avail.4. Before when i was using 5.3, it was not a problem..!!5. I tried the following command on other system. It shows the following output.
# ssh -v -l niks 43.88.101.99
OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008
debug1: Reading configuration data /etc/ssh/ssh_config
[code]....
I have installed qmailrock on my CentOS 5.4, finishing installation until sucees to launch webmail via GUI (squirrelmail). but my smtp service (:25) is always failed to connect.I can telnet on port 110, 80, etc. But on port 25, the result is not shown comment 220 oK.when i check using : qmailctl stat here the result :
/service/qmail-send: up (pid 26403) 5 seconds
/service/qmail-send/log: up (pid 26404) 5 seconds
/service/qmail-smtpd: up (pid 26455) 0 seconds
[code]....
FYI, i have installed postfix before, but i've un-install it using yum remove.
how to install CentOS VPN Server that can be connect from Microsoft Windows?
View 6 Replies View RelatedI have some virtual machines running with CentOS 5.3 (32 bit) and everything works as expected. To test a possible upgrade I took one of then and did yum clean all yum update after rebooting I get a kernel panic with the following message:
MP BIOS BUG : 8254 timer not connected to APIC IO I know that I can change the boot command not to use APIC and after that the machine boots again but I doubt that there has been any change to the virtual APIC implementation during the upgrade of the OS. Is there anything that iI should exclude from upgrading while working in a vm? I use VMWare Player 2.5.3 build-185404 on a 64 bit Ubuntu 9.04 as host.
I have a program that attaches to an interface. I can run two copies of the program on two systems (each running one instance), connect it to a switch, say 1.1.1.1 & 1.1.2.1. In this configuration two instances of the program can communicate and everything is fine.
Now, to reduce cost, it want to use only one system with two nics connected to the same switch, running two instances of the above program, each instance attached to two interfaces respectively on the system. I have the following settings:
eth1 Link encap:Ethernet HWaddr XXXXXXXXXXXXXXX
inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
eth2 Link encap:Ethernet HWaddr XXXXXXXXXXXXXXX
inet addr:1.1.2.1 Bcast:1.1.2.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[Code]...
I just installed CentOS 5 today. Had terminal open and got these errors:Quote:Message from syslogd@ at Wed Jul 8 12:38:33 2009 ...localhost kernel: Uhhuh. NMI received for unknown reason a0 on CPU 0.Message from syslogd@ at Wed Jul 8 12:38:33 2009 ...localhost kernel: You probably have a hardware problem with your RAM chipsMessage from syslogd@ at Wed Jul 8 12:38:33 2009
View 4 Replies View RelatedThe problems I was having earlier: [URL]seemed to be solved.
I was not getting any error messages after restart. I should have powered down fully, but did not think that it would make a difference. :(
The same issue is again occurring, but after shutdown ONLY and only on the first boot. After the first boot, a system restart will not cause any error messages. (I have rebooted at least ten or twenty times to make sure)
But after a system shutdown, the first boot hangs up and I get the
"Red Hat nash version 5.1.19.6 starting hdb: timeout waiting for DMA hdb: drive not ready for command"
errors five or six times before each boot. Also the system boots very slowly the first time.
I used the getinfo.sh all command and posted the info to the suggested site here: [URL]
Is it possible this could be a hardware issue? This is an old salvaged HDD. Ive changed everything I c an think of in the BIOS with no results.
I have used the hdparm -d /dev/hdb command and verified that dma is not being used on initial boot or after a shutoff but IS being used after a reboot...
here are the HDD settings
/dev/hdb:
multcount = 16 (on)
IO_support = 0 (default 16-bit)
unmaskirq = 0 (off)
[Code]....
I've made a CentOS 5 x86_64 setup last year, around november/december.This system is supposed to operate as a home router/gateway, firewall, nas, small intranet/extranet server and media center.I've previously built a system using older parts (Pentium III 866MHz), and had on it CentOS 5 x86.It successfully served the same purpose (except nas and media center) for quite some time, about 1-2years, until i felt i needed better hardware (more memory, speed and disk space mainly) and 64-bit support.
Part of this intended setup isn't finished (router/gateway, firewall, media center), partially because i'm still lacking a good 1000mbps switch and a supported wireless n 3-antenna card in AP/server mode.In the previous setup, i had router/gateway, firewall and small intranet/extranet server working, with a crappy 100mbps switch (the switch is broken now).the new setup has run pretty well, it had been upgraded 2 times, etc...But since it has been installed, even before any updates, upgrades or repo additions, there has been always warnings/errors during kernel boot.I'm listing my specs, configs, versions and logs bellow. all the partitions, RAID and LVM were created during CentOS initial setup.
Hardware:
Case:1x Cooler-Master CM-690 II Advanced (RC-692-KKN2)
PSU:1x Corsair VX450W (CMPSU-450VX)
[code]....
i rebooted my centOS 5.3 server an I got the the errors below. I need to recover the information its very critical.
Loading ahci .ko module
Loading dm-mem-cache .ko module
Device-mapper: uevent: version 1.0.3
Device-mapper: ioct1: 4.11.5-ioct1 (2007-12-12) initialized: dm-devel@redhat.com
Loading dm-log. Ko module
[Code]....
Suppose that it is not convenient to go behind a machine to have a look.So I want to use a command to show whether the cable is plugged into network card. (Media connected or not)Can ifconfig do this? Or another one?
View 2 Replies View RelatedI have a Nis server on Suse 11 which is configured using Yast and nis clients on Suse and CentOs .All clients which is on the Suse Os is working fine. But on CentOs , users couldn't login using nis username.I have mounted home directory using nfs in fstab . I can switch to nis users homedirectory only when i am root. But nis users could'nt login on reboot.' ypcat passwd username ' is showing the output . No selinux is enabled in the client .Is there is any problem with Suse server to Centos Client in nis ??
View 2 Replies View RelatedIm running an update through YUM from my CentOS5 64bit box and came across this error:Transaction Check
Error:
I've done some research on this and found solutions on how to rectify (i.e. reconfig YUM repositories etc.) but still same issue.
I'm running CentOS 5.3 x64 within a 32 bit version of Windows XP via VirtualBox. What I'm trying to do is install Eclipse such that I can code in both C++ and Java. I'm going to need to eventually add the OpenMP library, but that's later on. Right now, I'm just trying to get Eclipse to that point, I have the gcc and jre installed...it's just that Eclipse is not wanting to cooperate.
I did uninstall the open-jdk and install the Java SE 6u14. java version "1.6.0_14" Java(TM) SE Runtime Environment (build 1.6.0_14-b08) Java HotSpot(TM) 64-Bit Server VM (build 14.0-b16, mixed mode)
And the gcc... gcc (GCC) 4.1.2 20080704 (Red Hat 4.1.2-44) Copyright (C) 2006 Free Software Foundation, Inc. This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
I was able to install the Eclipse SDK using yum...
Eclipse Platform
Version: 3.2.0
Build id: M20060921-0945 (CentOS release 5 (Final))
However when I go to update it using Eclipse's update utility to install from the Eclipse Project Updates (in this case, Eclipse 3.2.2 update) I get:
Unable to complete action for feature "Eclipse Platform" due to errors.
Unable to complete action for feature "Eclipse RCP" due to errors.
Unable to create file "/usr/share/eclipse/plugins/com.ibm.icu_3.4.5.20061213.jar1249125532555.tmp". [/usr/share/eclipse/plugins/com.ibm.icu_3.4.5.20061213.jar1249125532555.tmp (Permission denied)]
[Code].....
I have just installed a fresh copy of CentOS 5.3 and from the get-go, the NIC started dropping packets like crazy. I even closed the port on the switch,. moved the cable to a different port,. All yield the same "dropping packets" behavior. Zero on the errors, just dropping packets. Should I stick a diff nic instead?
View 1 Replies View RelatedMy box is centos 5.3 x86. At booting, ipsec_setup messages are coming as attached picture.
And dhcpd also comes "failed".
How to figure out why there are errors on bond0(eth0)
Transfer speed is in KB
I've installed a 500 Mb WD HD (Sata3) in my Centos 5 Server (AMD QuadCore) - Linux 2.6.18-128.el5 #1 SMP (x86_64)
Fdisk keeps failing with the following message - kernel: ata1: SError: { HostInt Handshk }
Tim Weil
Silver Spring, MD.
tweil@securityfeeds.net
When using YUM UPDATE from the prompt more than 230 items are scheduled for update however when the download process has completed I receive errors regarding Perl dependences such as:
file /usr/lib/perl5/5.8.8/List/Util.pm from install of perl-5.8.8-27.el5.x86_64 conflicts with file from package perl-5.8.8-18.el5_3.1.i386
I am unsure how to overcome this. It occurs on two different servers.
When try to yum install sendmail geting errors:
View 3 Replies View RelatedI am a complete novice when it comes to Linux, but want to learn, and installed CentOS5 on an old P4 Dell I had lying around.
Dell Dimension 8100 BIOS is version A02
Install seemed to go fine, but when I power up I get the following message
Red Hat nash version 5.1.19.6 starting
hdb: timeout waiting for DMA
hdb: drive not ready for command
this happens a few times each, then CentOS finally loads.
If Im understanding this right, DMA is direct memory access.
Is it possible the hard drive, motherboard etc does not support this?