CentOS 5 Networking :: Ethernet With Lenovo IdeaCentre Q150?
Aug 11, 2010
I am installing Centos 5.5 on a new Lenovo IdeaCentre Q150-40813AU and have been having an issue with getting the correct Ethernet driver. After Googling for a while, I found a similar type question where the following two commands were suggested; however, my results do not match the ones on that thread so I am not sure how I should proceed.
# /sbin/lspci -m | grep net
01:08.0 "Ethernet controller" "Intel Corporation" "82552 10/100 Network Connection" -r02 "Lenovo" "Unknown device 3605"
# /sbin/lspci -n | grep "$(/sbin/lspci | awk '/net/ { print $1 }')"
01:08.0 0200: 8086:10fe (rev 02)
View 3 Replies
ADVERTISEMENT
Jan 9, 2011
Tried the normal fixes and installed the wrapper, etc. Wired network works fine, and I am able to access some unlocked wifi networks from neighbors, but I cannot access my own password protected network. It just keeps asking for the password and never connects. Fairly new Ubuntu guy here.
[code]....
View 7 Replies
View Related
Feb 16, 2011
I need (would like) to get the wireless running on my Lenovo q150. It uses the realtek 8191u chip for the wireless. I tried the steps in [URL]. But failed miserably. Now the Q150 will not boot. It locked up after the modprobe and I was forced to use the power switch. I was using a fresh install of maverick amd64.
View 6 Replies
View Related
Jun 22, 2010
give me link for NIC card driver for Lenovo MT-M 7298-AG1 Desktop machie LAN and Sound Driver..
View 1 Replies
View Related
Jun 8, 2011
I have a Lenovo T410 laptop. I'm unable to find drivers for the ethernet card, the wireless card and graphics. I don't even know what hardware is installed in the system. Here is the product ID if it can help in identifying the hardware.
Product ID : 2516CTO
View 9 Replies
View Related
Sep 13, 2010
I've installed from the CD the Centos version 5.5. When I try to connect to Internet I can't because I received some errors. I've the Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller also a wireless slot (I've the wireless card DWL-G650+) When I turn on the pc and I go to "Ethernet Device", I see set: peth0 (Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) ETHERNET CONTROLLER) and also set "Bind to MAC address": fe:ff:ff:ff:ff:ff I've set manually the IP address (I'm under router). Status is "Active" but can't go on the Net. When I change to "eth0 (Intel EtherExpress/100 driver)...sometimes become "Active" an other times said that the MAC address is different or to check the cable because can't find the IP. What can I do?
View 5 Replies
View Related
May 4, 2009
I am using asus p5ld2-x/1333 motherboard,I installed the centos ,Centos saw other drivers but didn't see ethernet card.I am not connection the internet.
View 2 Replies
View Related
Feb 10, 2011
Pl can anyone guide me to connect centos 5.5 using ethernet port to ADSL Broadband modem which is configured in PPPoe mode?
View 19 Replies
View Related
May 19, 2009
i did configure as it was advised on [URL]... but it didn't work. for eg I added eth0:1 and eth0:2 on /etc/sysconfig/network-scripts/ when i do ifconfig i can see only eth0:1, i cannot see eth0:2, eventhough i configured as it was on the tutorial
View 4 Replies
View Related
Nov 23, 2010
I'm trying to connect my newly installed CentOs 5.5 to the network. But although there is a cable connection that has worked well before with other distributions, the network configuration keeps telling me:"Determining IP information for eth0... failed; no link present. Check cable?"Here are the results of the /.getinfo network script:This is a university network that is working well for thousands of students, so the problem is not on the side of the network or the DHCP server.The wireless card is also not shown in the network configuration.
View 1 Replies
View Related
Jun 7, 2010
I recently installed CentOS on a really old computer and while most things are running well, I am unable to connect to the internet. Using a Damn Small Linux live CD I am able to connect just fine and was able to see that that 'hp100' was being used as the netcard driver. When I tried to set up the network card using that adapter (HP10/100VG ....) it gives me the following error code...
View 1 Replies
View Related
Jul 6, 2010
I have a server in a colocation environment where I'm allotted 25Mbps. I'd like to avoid exceeding that for obvious reasons. Is there a way I can set the link speed or at least throttle the bandwidth for all services?
View 2 Replies
View Related
Sep 12, 2011
Currently I have a server which runs under centOS 5.6. It is dedicated to the VoIP application of my customer.I have a problem for which I have the solution but I didn't managed to achieve it.So, let me explain you the context.Here is the networking aspects of my environment
VoIP Provider_____Gateway_____________My server
ADSL Provider____(non pingable)
x.x.x.2 <====> A.A.A.1 <======> A.A.A.3
[code]....
View 2 Replies
View Related
Oct 15, 2009
Cent Os 5.3 64bit dosen't recognise the network card ASUS NX110113f0:1023 (rev41)here are some details about the system,
# lspci | grep ther
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
[code]....
View 6 Replies
View Related
May 22, 2010
I changed a mainboard so the network card is RTL8111/8168B Gigabit now. By "ifconfig -a", there is only io, no eth0.
I got a driver r8168.ko from: [URL]
After I insert the r8168.ko, there is eth0. Run "/etc/init.d/network restart", it reports "Determing IP information for eth0... failed; no link present, Check Cable", and I noticed the lights of network card and runter are all off. I can use "ifconfig eth0" now but it cannot connect to other machine.
It's Gigabit card and my runter is 10/100M. I tried "#insmod r8168 speed=100 duplex=1 autoneg=1" and "#insmod r8168 speed=100 duplex=0 autoneg=1", it can not get IP by DHCP either. I also build the .ko from Realteck source code, the behavior is the same.
if I need to do other configurations?
My CentOS is CentOS5, 2.6.18-8.el5 #1 SMP.
== BEGIN uname -rmi ==
2.6.18-8.el5 i686 i386
== END uname -rmi ==
== BEGIN rpm -q centos-release ==
[Code].....
View 5 Replies
View Related
Sep 4, 2010
I have built-in-motherboard Ethernet with this MArvell 88e8059 chip. During CentOS 5.5 install it didnt find it. then i found some page here on forums which said how to install sk98lin driver, and several people reported it working after that. Their chips were 8056 and others.. So i decided that should probably work in my case too, i installed it, and then i could see it in Network COnfiguration manager.
But during reboot, it cannot obtain IP information, and in Network Config manager it is "Inactive", setting it to Active fails to obtain IP again...
View 7 Replies
View Related
Mar 14, 2011
Im new to this Cent OS as well as Unix based Operating Systems. Please help me with the below requirement.My Company is a Serach based data collector from different websites like Google, Yahoo & many more..Collecting the data from the search engines is a issue for right now.. As many search engines are blocking us to search and retrive the date after some time.. Taking Google as example : Google Blocks my IP after every 30 mins of retriving.. Application is a Windows based & using Windows 2003 as the Server.. Would like to give a Dynamic IP to the Windows Server via 1st Ethernet Card & enable the 2nd Ethernet for the Internet..Eg : eth 0 = 192.168.1.1eth 1 = x.x.x.x (Public IP)I have check with few of my friends who told me to get Linux or Cent OS installed to do a interface disable after given time & enable a secondary device or virtual interface the next couple of seconds... Like eg : eth 1 = x.x.x.1 eth 2 = x.x.x.2 eth 3 = x.x.x.3 so on.. Would like the eth 1 to be down after 60 mins & eth 2 o be up & again after 60 mins of up time eth 2 down & eth 3 up.
View 6 Replies
View Related
Jun 26, 2011
I am unable to find Atheros AR8132 PCI-E Ethernet Controller driver for CentOS which is installed on my netbook.
I contacted DELL to provide me the driver and they said that they do not support Linux on netbook and I have to arrange it myself.
I told them that I don't need help in installing I just need the driver file to which they said that they don't have driver for Linux.
NIC is getting detected and works fine on the same netbook (Am dual booting Windows7/CentOS) with Windows7
When I type: ls -l /dev/ it does not show up eth0. Same result with ifconfig. When I type lspci | grep net it does show up something like Atheros Communications AR8132 L1 PCI Gigabit .
View 4 Replies
View Related
Mar 20, 2009
I have several systems experiencing this issue, but the "worst case" system at the moment is a system where there are 2 dual-port PCI-X e1000 cards, and two on-board e1000e PCI-express card.What happens is maddening. If the /etc/sysconfig/hwconf is removed, and kudzu is not run, and the 6 interfaces each have a corresponding script:
/etc/sysconfig/network-script/ifcfg-eth0
/etc/sysconfig/network-script/ifcfg-eth1
/etc/sysconfig/network-script/ifcfg-eth2[code]...
Now what happens defies explanation. The only way I can be sure to make the e1000e first-listed-in-pci-order e1000e device always eth0 is to remake the initrd and add e1000e to the initrd.If I do not do that, eth0 might be the onboard night, it can also be the first port on either of the dual port cards.So eth0, eth2 and eth4 all take turns being eth0. This was not an issue in the EL-5.1 timeframe. This is certainly new to the EL-5.2 timeframe and thus far is not possible to control because the system does not load eth0's driver alias in order, and the enumeration of the PCI devices causes what seems to be random labeling of the first interface.
This is a particular problem in that identical hardware systems will come up with different eth0 interfaces , and on a single system, without the /etc/sysconfig/hwconf (which calls "eth0" something different from what was originally in the /etc/sysconfig/network-scripts/ifcfg-eth0 HWADDR directive).I need as little auto-magic as possible, I can live with PCI-bus order and driver load order is the order ethernet devices appear in, I cannot use the software in a state where what is "eth0" is randomly determined and the only way I can nail it down is to run kudzu, generate a hwconf AND brand the network interfaces in the network-scripts with HWADDR. I've been using EL since 6.2 and this is the first time I've ever encountered a situation where the enumeration rules (which are ancient at this point) over-ridden by something.
Version-Release number of selected component (if applicable): EL-5.2 series.The random enumeration of PCI devices and the subsequent assigning of eth0 to a random NIC is not on every reboot, and does not seem tied to a power off scenario vs a simple reset or warm reboot. Over the course of 0 reboots , eth0 should have moved between 2-3 times.Packages that seem relevant.
View 19 Replies
View Related
Feb 26, 2010
I have installed trixbox 2.8.0.3 in Intel MAC mini PC, installation completed successfully. After reboot network card was not detected.
My MAC mini PC comes with nVidia Corporation MCP79 Ethernet card. how to enable Ethernet card with out affecting the tribox. trixbox-2.8.0.3 version comes with Cent OS 5.4. [Moderator edit: s/deducted/detected/]
View 5 Replies
View Related
Jul 7, 2011
I have installed CentOS. I have two ethernet card (one onboard and one PCI). I am able to set ip for realtek ethernet card and my atheros(on board) is not shown in network ifconfig shows only one ethernet card (PCI) hen i gave the command lspci i got the following output
01:00.0 Ethernet controller: Atheros Communications AR8132 Fast Ethernet (rev c0)
03:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
View 4 Replies
View Related
Sep 20, 2010
from [URL]
i did the following
[root@localhost ~]# lspci | grep Wireless
0c:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
View 5 Replies
View Related
Sep 1, 2011
My laptop was working fine on wireless till the userinterface changed and it defaulted to ethernet and now it won't let me go back on wireless How do i disable ethernet?
View 4 Replies
View Related
Aug 13, 2009
I just downloaded the 7 centos5 isos and burned them on cd (checksums alright). After rebooting my x200s with ultrabase the start screen of centos together with the boot promt appears. After I hit <Enter> nothing seems to happen and after some time there a message saying something like "disk failure..."
Does the CentOS installer does not support the x200 ultrabase?
View 1 Replies
View Related
Aug 25, 2011
Just loaded Centos 5.6 on my old Lenovo t400. Works great with on exception. Can't get the wireless turned on. It's an Intel PRO/wireless 5100 AGN (shiloh).
The external switch is on. FN+F5 does nothing.
It's in the device list but does not appear in Network Connections.
View 3 Replies
View Related
Aug 27, 2010
I have Centos 5.5 running on this laptop but can't get gobi_loader(loads firmware onto the 3g device and then you can use wvdial) working on kernel 2.6.18-194.11.1.el5 (x86_64). lsusb shows the Gobi device but gobi_loader uses /dev/ttyUSB0 which doesn't exist.
View 18 Replies
View Related
Oct 17, 2010
This is probably trivial for most linux users, but here is what I did to get wireless working with the Centos 5.5 LiveCD on my Lenovo S12.
For reference, here is the output of the lspci command:
View 3 Replies
View Related
Dec 21, 2009
I have installed CentOS 5.3 on my PC which has an Atheros AR8121/8113/8114 Gigabit Ethernet. Unfortunately 5.3 has no drivers for this LAN Card. I searched the Google for drivers but was unable to find any. Does the 5.4 has them? If yes then how can i upgrade it to 5.4 without Network connectivity?
View 11 Replies
View Related
May 4, 2009
I was try to compile the drirver from cd asus, but my lan card still not detected in centos 5.3. when i bringing up eth0 its show like : "the atl2 device eth0 does not to be present, delaying initialization."iwas suft on google some driver but all driver just to centos 5.3 when i install the rpm it does not work. i love centos i dont want to change my lovely centos.
View 10 Replies
View Related
Oct 29, 2010
I've installed a new fresh Centos 5.5 ..and after a lot of work..something starts to work (X now works with the new ATI HD5145 using ATI drivers) but i've a serious problemThe ethernet controller JMC250 JMicron PCI EXPR. doesent work at all so my notebook is out of the world !!!Here is some infos:rpm -q centos-release
centos-release-5-5.el5.centos
rpm -qa kernel* | sort
kernel-devel-2.6.18-194.el5
[code]....
View 6 Replies
View Related
