I have a server in a colocation environment where I'm allotted 25Mbps. I'd like to avoid exceeding that for obvious reasons. Is there a way I can set the link speed or at least throttle the bandwidth for all services?
View 2 RepliesPl can anyone guide me to connect centos 5.5 using ethernet port to ADSL Broadband modem which is configured in PPPoe mode?
View 19 Replies View RelatedI'd like to use tc and iptables to restrict the download speed. I understand this is know as policing. Are there some resources I could use to learn how to do this? I want to restrict on a per ip basis.
View 1 Replies View RelatedI have a Fedora 11 system and cbq.init-v0.7.3 in it. Now I want to restrict upload speed from my ftp server to Internet (eth1). According to docs I've made a simple file /etc/sysconfig/cbq/cbq- 00.inet_upload_restrict:
DEVICE=eth1,100Mbit,10Mbit
RATE=800Kbit
WEIGHT=80Kbit
PRIO=5
RULE=:20,
So as you can see I want to limit outbound traffic on eth1 from my ftp port 20 to any to the 800Kbit/s (100Kbyte/s). Now I do cbq start, it says: find: warning: you have specified the -maxdepth option after a non-option argument (, but options are not positional (-maxdepth affects tests specified before it as well as those specified after it). Please specify options before other arguments.
find: warning: you have specified the -maxdepth option after a non-option argument (, but options are not positional (-maxdepth affects tests specified before it as well as those specified after it). Please specify options before other arguments. but it starts and works. Now I check the speed and it is...
i have an embbeded hardware that uses bootp for booting from a Network Managemnt Host (NMH)on the same ethernet. The embedded hardware has both kind of ports i.e ethernet as well as E1/T1. I would like ask, what do i require to establish a communication-link between the embedded hardware and the NMH throuh E1/T1 ports of embedded hardware, so as to make it boot through from E1/T1. Further, NMH possesses only ethernet port. Just to refine my questions i'd like to know what additions do i need to do on my NMH , like may be i have to put an E1/T1 port or is it possible that the E1/T1 port can be directly connected to an ethernet port on the other host.
pardon me if i am not making absolute sense here as my knowledge is limited on Layer 1 and layer 2.
I have been doing a variety of speed tests on my ethernet connection in preparation for upgrading my service and found that the connection on my dell d630 is not getting expected download speeds. In fact, it is getting about a third of the expected speed. This machine is running Lucid. It also dual boots Windows Vista. Checking Vista a moment ago, the speed is fine. What could be the problem that is preventing the ethernet from working at 100%?
View 7 Replies View RelatedI have a CentOS 5.5 machine (hosted at a remote hosting company) where "ethtool" reports that the eth0 device is currently in 10 Mbps mode, but the output indicates that it supports 100 Mbps. But if I try using ethtool to switch the device into 100 Mbps mode, it doesn't work; after running the command to switch it to 100 Mbps, ethtool reports the speed is still 10 Mbps:
[root@sls-eb5p17 network-scripts]# ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
[Code]...
The man page at [URL]..ethtool seems to suggest that this should have worked. Any reason why the reported speed of the device didn't change? Changing other settings doesn't appear to work either, e.g. if I specify "duplex half" instead of "speed 100", eth0 still reports "Duplex: Full".
I can't figure this out for the life of me. I am new to Linux too. Wireless works fine. I plug my Ethernet in and turn off wireless and I cant surf the web, download, etc...Network Manager finds the wired network under eth0 and it works perfect on my non-linux desktop (nervous to even mention Vista around here). Firewall was set up with basic setup (I didn't make any changes). I have a Sony vaio VPCCW21FX with fedora 13. Can anyone point me in the right direction?
View 10 Replies View RelatedI am running 11.04 on a Dell Inspiron 1501 (the first gen.). I was using my Ethernet port to connect to the internet until about two weeks ago - suddenly the system no longer recognised that port even existed and just kicked me offline. I am able to get online now with a wireless card (replaced the broadcom card, that was a whole different can of worms...).
why my system is unable to connect with the Ethernet port? If I plug in the cable nothing happens.
I have a Dell Studio 1501 Laptop and I want to bridge the wireless with the ethernet port so I can hook my xbox360 to my laptop.
I've spent the last 2 hours trying different techniques but nothing is working.
I'm running Ubuntu 9.10 so the last thing I tried was going into the network manager, clicking on wired, editing the ethernet port and allowing it to share. This did nothing.
I tried to share the connect with firestarter but that did not work either.
I am using ubuntu 9 but unable to connect to internet via my usb Siemens c110 modem. I have a dual boot system of both windows7 and ubuntu9. I am using the same modem in windows7 and have installed virtualbox where i have installed the same ubuntu9 but there it automatically detects the wired connection(usb)[eth0] but in the actual boot it doesnt detect anything. I have typed in the terminal sudo ppconfig but it was unable to find anything.
View 1 Replies View RelatedI am running Ubuntu 11.04 and i am curious to if there is a way to share my established wireless connection through my Ethernet port.. I know it was possible in Windows by going to adapters and bridging the wireless, and Ethernet adapters. how to make this work in Ubuntu?
View 1 Replies View RelatedI have a simple server running Ubuntu Server. Usually the server connects to the network by Wifi, so there is usually no cable connected to the Ethernet port. I noticed that there is a dhclient3 running on eth0 anyway. It is causing undesirable disk activity. Obviously, it is never going to get a response as long as no cable is connected. I can kill the responsible process manually, but I wonder first what is starting the process and how I can prevent it from being started. If there is a way to get the server to boot without starting this process, I wonder whether this is the right solution. Connecting to the network by Ethernet is the failsafe when Wifi doesn't work. I guess what I would like to see would be a way for the server to detect when eth0 does not have a cable connected and not start dhclient in that case, but to activate dhclient when a cable is connected.
View 4 Replies View RelatedI changed to a 4 port ethernet router (D-Link DSL-2542B Adsl2+)with intention to share Internet access with my brother (he's on Vista).Initially it all went well,but 3 days ago there were connection problems occured on the part of the ISP. Without realized the problem,I had reset the router.This morning I've been informed by the ISP that the connection has been re-established.So,I accessed the Internet via the 4 port router but failed to do so (server not found).Suspecting that the problem was from the 4 port router,I reverted to my old Adsl router (DSL-520B single port) and without any problem I managed to access the Internet back.I really need help to configure back the 4 port ethernet router to its initial state.
View 9 Replies View RelatedI'm running an ubuntu maverick server, and I'm having a slight problem with networking. I've only got one ethernet line running into my room, and I've got loads of computers. The server has 2 ethernet ports, one integrated into the motherboard, one on a PCI card that I took from my old server. The on board ethernet never worked on my old server- but I only tried it out post-install, it was hooked up to the card during install (For the record, networking on linux has *never* worked for me if I installed then plugged in the networking stuff after the fact). So I just used the card instead. Transferred the hard drive into a new machine, and lo and behold, it would only work after I transferred in the card from the old one. What I wanted to set up is a basic NAT system, where the network connection is routed through from my server to my main desktop- but when I run ifconfig, my card is not detected, just lo and eth0. How can I fix this?
View 3 Replies View RelatedI want to transfer the audio file on linux machine using Ethernet port, is it possible?
View 6 Replies View RelatedI am using Ubuntu 10.04 Lucid and VMware 2.0 server. I have a an XP virtual machine that is needed for work. When I am at home and I place my cat 5 cable to my cisco catalyst switch, my XP VM recognizes the ethernet card on my laptop and bridges fine with ubuntu and works fine and I can get to my network. When I take my laptop to work and I go to a site and I plug it into a World Wide Packet 311 management port on the switch, my XP Virtual Machine does not see the network no matter what setting I set it too(100 full, 10 full, 10 half and etc). It simply says that the network card is disconnect. Ubuntu see the network fine and I can ping and talk to the network without any issues but the VM does not.
View 2 Replies View RelatedI'm currently using Ubuntu 9.1, and a motherboard which has two Ethernet ports on it.
What I would like to do is bridge these ports, so I can plug in another Ethernet cable and run it to an unmanaged switch in my room (handy for my work laptop when on-call and building other PCs, etc).
I.e. Router --> 8-Port Switch --> My PC.
Eth 0 --> 192.168.1.100 static
Eth 1 --> 5-Port Switch --> DHCP
I believe this is the config to make the ports bridged:
ifconfig Eth0 0.0.0.0
ifconfig Eth1 0.0.0.0
brctl addbr Bridge0
brctl addif Bridge0 Eth0
brctl addif Bridge0 Eth1
ifconfig Bridge0 up
- How do I save this so upon reboot it sticks?
- How do I force Eth0 to remain as a static IP of 192.168.1.100?
I have a Dell WLAN 1397 Half Minicard, 802.11 b/g card in my laptop, and I can't seem to get ubuntu to work with it. I tried this method:
1. Synaptic Pack Manager
2. Check "Install from Boot Disc"
3. Reload
4. Install and apply bcmwl-kernel-source
5. Reboot
This didn't work for me, so I tried entering sudo apt-get install bcmwl-kernel-source and that also didn't work. Another thing I tried is formatting my Ubuntu partition and reinstalling, and retrying both of those methods. The ethernet port does work, however.
I recently installed a new CPU and motherboard in my Media Server, but the ethernet port isn't showing up under ifconfig. Is there any way to install additional drivers? EDIT: The model is Realtek RTL8111/8160B.
View 3 Replies View Relatedwhile my brother was browsing the web on my windows partition he had a blue screen pop up, one of the soft/hardware error ones, not a true BSOD, anyways, ever since my lan port on the computer seems to not be activiating as no wired connection is recognized. The lan port/card is directly attached to the Mother Board, it's a gigabyte motherboard in a self-build computer. I'm just wondering if there's anything I can do to troubleshoot this and see if it is truly a hardware problem or if its something else.
View 9 Replies View RelatedI've installed from the CD the Centos version 5.5. When I try to connect to Internet I can't because I received some errors. I've the Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller also a wireless slot (I've the wireless card DWL-G650+) When I turn on the pc and I go to "Ethernet Device", I see set: peth0 (Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) ETHERNET CONTROLLER) and also set "Bind to MAC address": fe:ff:ff:ff:ff:ff I've set manually the IP address (I'm under router). Status is "Active" but can't go on the Net. When I change to "eth0 (Intel EtherExpress/100 driver)...sometimes become "Active" an other times said that the MAC address is different or to check the cable because can't find the IP. What can I do?
View 5 Replies View RelatedI am using asus p5ld2-x/1333 motherboard,I installed the centos ,Centos saw other drivers but didn't see ethernet card.I am not connection the internet.
View 2 Replies View RelatedI tried changing the sftpserver port but its not working, besides how can i restrict users from particular ips.Eg: users a can ssh from 192.168.*.*user b can sftp from 200.*.*
View 2 Replies View RelatedIs it possible to restrict telnet connection from remote to my server(linux -centos5)?
=================
Ex : [root@localhost]# telnet 10.0.0.33 80
Trying 10.0.0.33...
[code]...
Can anyone here point me to a walk-through or discussion of how to use Webmin to set up port forwarding/NAT on a dual-NIC Centos 5.3 box? The layout will be simple:
Internet --- NIC1 [CentOS Box] NIC2 --- Switch to other PCs
We have a BUNCH of exposed services that are on special ports -- for example, to connect to one machine, you go in with [IP_Address]:12000, and to connect to another, [IP_Address]:12002, etc., etc. We're currently using OpenSuse 10.3 on this box, and YaST makes this criminally easy (you give it the incoming port number and the destination IP/port numbers and it just works). But OpenSuse 10.3 is nearing EOL, we're buying a new machine, and I'd like to use CentOS on the new one.
I've read the sparse Webmin documentation in their Wiki, and it leads one to believe that you simply insert a "NAT" rule. But there's obviously something they're leaving out. I *am* opening the ports in the firewall. But when I log in to [IP_Address]:port, it just times out. The port forwarding never occurs. The test in this case is SSH, and I know that SSHD is working properly because I can log into that machine just fine from another PC on the same internal subnet.
i am not able to port 8080 on my CentOS VPS server.I have followed all the instuctions as mentioned on iptables wiki page.Also I am able to telnet my ip address and port number, But can not access from browser.
View 6 Replies View RelatedI currently have debian installed dual booting with windows 7. Whenever I go to speedtest.net I ger over 20mbs with windows 7 and .098mbs with debian and ubuntu can wnyone tell me what is going on. I called AT&T Uverse and they said that I had over 900 file sharing sessions still open and that is what was causing the problem so they reset my network gateway for me ad we tried again, same thing debian low ethernet speed windows 7 very high ethernet speed can anyone help me out with this
View 4 Replies View Relatedi am using openssh 5.2-p1, i want to restrict user "admin" to login to the server from a specific IP address, for this purpose i have tried the following blocks in sshd_config file.Following is the part of the sshd_config file which i have modified
#The following commands will only allow specific IP to login to ssh.
#AllowUsers admin user1 user2
#AllowGroups
# override default of no subsystems.Subsystem sftp internal-sftp
Match Group sftpgroup
ChrootDirectory /home
AllowTCPForwarding no[code].....
i want to restrict admin user to login to the server only from 172.16.100.221 IP which can be done by using AllowUser line, but i dont want to use AllowUser line,
i did configure as it was advised on [URL]... but it didn't work. for eg I added eth0:1 and eth0:2 on /etc/sysconfig/network-scripts/ when i do ifconfig i can see only eth0:1, i cannot see eth0:2, eventhough i configured as it was on the tutorial
View 4 Replies View Related