Ubuntu Installation :: Using Wireless USB Network Adapter?

Oct 20, 2010

I just started using Ubuntu 10.10 recently. and Im not really sure how most of this stuff works. I could probably figure most of it out myself, but I have a question about using a wireless USB stick for internet.I do not have internet on my desktop (the computer with linux on it) and the only way i can get it is by using a Dynex Wireless G USB Network Adapter.

I do not have the disk for it. and Im guessing linux doesnt have the autoinstall thing that windows has (no offense to linux, im starting to love it more than windows). I have the driver for it on my windows computer. I was wondering if i could run the driver from a usb thumb drive.If not, then how can i get the network adapter to work?

View 5 Replies


ADVERTISEMENT

Fedora Installation :: Wireless Network Configuration - B43 Adapter Grayed Out

May 9, 2009

I am doing network config of my laptop. I'm new to Fedora, so I'm not sure how it goes ...
I have an Ethernet device (eth0) and a wireless device, wlan0
Status in system->administration->network:
Tab devices:
eth0 : active
wlan0: inactive
Tab Hardware:
eth0: system
wlan0: configured (description: b43)

Double clicking on the wlan0 line gets you to Network Adapters Configuration, where adapter b43 grayed out) is associated with device wlan0. So far, so good (I did all the fwcutter stuff, so I assume this is the result). When I installed the system (from installcd, then update, then install broadcom-wl, ...) I configured it to be started up with network manager, automatically on startup. I managed to get it working exactly once in that session.

Problem is, it doesn't start up and the wireless is not even visible when you click the network manager icon. For that matter, eth0 does not start automatically either, but at least there is a button to start it in network manager. Coming back to the tab devices, clicking on wlan0 allows you to click on the activate button ... but there it says: Cannot activate network device wlan0! b43 device wlan0 does not seem to be present.

View 6 Replies View Related

Ubuntu Networking :: Get Wireless Network Adapter To Be Read By 'Windows Wireless Drivers'

Nov 24, 2010

I recently reformatted and dual partitioned to both Windows 7 as well as ubuntu 10.10. Loading works fine and Windows 7 is 100% operational. I cannot seem to get my wireless network adapter to be read by Ubuntus 'Windows Wireless Drivers' gui. Here are the steps that I have done THUS far, to make sure that we are all on the right path. Before I go any further, my wireless network adapter is an old school WUSB11 Linksys Wireless Network Adapter (running version 2.6).

1) Downloaded and installed "ndiswrapper" from ubuntu's main website. I downloaded the common, utils and ndisgtk files and installed them accordingly.
2) I extracted these three files to the desktop of Ubuntu and accessed the terminal page.
3) From terminal I typed "cd Desktop" to change the directory to the desktop.
4) Next, I typed in "Sudo dpkg -i ndiswrapper-common_1.54-2ubuntu1_all.deb
Sudo dpkg -i ndiswrapper-utils-1.9_1.54-2ubuntu1_i386.deb
Sudo dpkg -i ndisgtk_0.8.5-1_i386.deb"
5) This installed Windows Wireless Drivers gui successfully and I can access it.
6) I have downloaded the driver files for the adapter from the cisco website and searched them for the required files needed.
7) After extracting the .INF file from the "Drivers" directory named "NETUSB.SYS" (I wasn't sure if the other associated files within the same folder needed to be present together with NETUSB so I moved everything to the desktop) I typed in "sudo ndiswrapper -i NETUSB.inf". After accessing the Windows Wireless Drivers gui I have noticed that the 'netusb' driver is present yet under it, the system states "Hardware present: No". This leads me to believe that maybe I installed incorrectly or my "fireware?" is not present? I was reading through the installation guide posted on the ubuntu website that in addition to the .INF file we also need the BIN file(s)? and SYS file(s)?.. The folder with the drivers for my adapter contains a BIN file but it is not within the "Drivers" section of the folder.
9) Upon mousing over the network Icon naturally my hardware is still not present.
10) From what I gather after the system finds the hardware I am to write into the terminal

[Code]....

View 2 Replies View Related

Ubuntu :: Get Wireless Access To WiFi Router With Xbox360 Wireless Network Adapter

Dec 10, 2010

I want to try to get wireless access to the wifi router with the xbox360 wireless network adapter.Is this possible?

View 1 Replies View Related

Ubuntu Networking :: Wireless Unstable In 10.04 - AR5001 Wireless Network Adapter

Aug 30, 2010

I am severe wireless problems with Ubuntu 10.04 on my laptop.(Spec below)

I have just performed the first clean install since new. Installed a new Hard Drive as well. The machine and wifi was fine under Ubuntu 9.04.

It is booting much faster now but the wifi keeps dropping off.

Spec:

Machine - Acer Aspire 4310
Wireless card - *-network
description: Wireless interface
product: AR5001 Wireless Network Adapter
vendor: Atheros Communications Inc.

[Code].....

View 2 Replies View Related

Ubuntu Networking :: Belkin Enhanced Wireless USB Network Adapter - Windows Wireless Drivers App Doesn't Work

Feb 3, 2010

I have a Belkin Enhanced Wireless USB Network Adapter Model # F6D4050 v2. The drivers are for windows but the windows wireless drivers app doesnt work. I see a tutorial for a linksys that appears to have the same chipset, but I am not sure if any of the steps need to be modified, also my kernel is a bit different. Here is my kernel:

[code]...

View 1 Replies View Related

Software :: Installing Wireless Drivers With Atheros AR9285 Wireless Network Adapter?

Jan 12, 2011

I have recently installed Linux Mint 10 on my laptop. When I look at the Device Manager in Windows 7, it says I have an Atheros AR9285 Wireless Network Adapter. Right now, I am unable to connect to wifi with Linux. What drivers am I able to install, and how would I install them?

View 3 Replies View Related

OpenSUSE Wireless :: GNOME 3 Broke AR9285 Wireless Network Adapter - Could Not Make A Connection

Apr 23, 2011

I own an ASUS N61JV-X2 notebook PC. It has an Atheros Communication, Inc. AR9285 Wireless Network Adapter. 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 0280: 168c:002b (rev 01) I cannot see any SSIDs including my home Verizon FiOS 802.11 G WPA2-AES-TKIP encrypted network. I went to Starbucks to try to connect to their free Wi-Fi and I could not make a connection. How do I solve this problem so that I can connect to a SSID of my choice and make a wireless connection while using GNOME 3?

View 2 Replies View Related

Ubuntu :: Can't Connect To Our Wireless Network Without Adapter

Aug 17, 2010

We need to fina a wireles adapter that works with Ubuntu.We have a netgear adapter but the OS doesn't recognize it when we plug it into the USB port and there isn't software to install so it will recognize it - only Windows documentation.My daughter loves this OS and wants to keep it but can't connect to our wireless network without an adapter.

View 7 Replies View Related

Ubuntu Networking :: Wireless Adapter Cannot Connect To Any Network

Aug 31, 2010

I have an HP Pavilion dv5 1002nr laptop running Vista. I decided to install Ubuntu using the windows installer, which did install well, but I decided that it wasn't for me, and uninstalled it. Now, my wireless adapter which is a Atheros AR5007 802.11b/g can see the network, find networks by itself, and is supposedly installed correctly according to Vista, cannot connect to any networks at all despite being able to see them and acquire a signal strength. Up until installing Ubuntu I have never had an issue like this. Other devices have no trouble connecting to this network, and I am currently using a Netgear wireless usb dongle to connect to the very network that my Atheros can not connect to.

View 2 Replies View Related

OpenSUSE Network :: 11.3 - Setting Wireless USB Adapter

Dec 22, 2010

After had installed opensuse 11.3 I am about toset a usb stick and connecting to internet. I can connect with ethernet but as I want to have also wireless internet I bought a LEVELONE WUA-0605 wireless usb adapter witch I can't setup and connect...
The only data witch I was able to find are:

linux-0wi7:~ # hwinfo --wlan
21: USB 00.0: 0282 WLAN controller
[Created at usb.122]
Unique ID: 2UT6.NomXlQ88uo3
Parent ID: k4bc.9T1GDCLyFd9
SysFS ID: /devices/pci0000:00/0000:00:1d.7/usb1/1-3/1-3:1.0
SysFS BusID: 1-3:1.0 .....

View 9 Replies View Related

Ubuntu Networking :: Will The Xbox 360 Wireless Network Adapter Work?

May 17, 2010

How do i get my xbox 360 wireless adapter to work on ubuntu?

View 2 Replies View Related

Ubuntu Networking :: Can't Detect Network On AWU212N Wireless Adapter / Fix It?

Jul 9, 2010

I just got a new AZiO AWU212N 802.11n wireless usb adapter (linked below). One of the product reviews said that it works with Ubuntu if you upgrade to the .34 kernel so I thought it would be a good buy. I updated my kernel and Ubuntu detects that there is a wireless adapter, but doesn't detect any networks. My old wireless-g adapter can connect just fine, so I don't know what the problem is.

http://www.newegg.com/Product/Produc...82E16833340018

View 3 Replies View Related

Ubuntu Networking :: Installing A PEX300WN2X3 Wireless Network Adapter On 10.10

Feb 15, 2011

I am trying to install a Star Tech PEX300WN2X3 wireless card but I'm completely lost. The installation Cd has 2 tar. files with the linux drivers but I'm just clueless as to what to do with them.

View 9 Replies View Related

Ubuntu Networking :: TP-Link Wireless Adapter (USB) On 11.04 - Not Connecting To Network?

May 19, 2011

i just installed Ubuntu 11.04 64bit on my desktop. i have a TP Link TL-WN321G (Ver 4.0) wireless usb adapter to connect to my wireless network (i used to use it with Windows XP).As expected (i'd read up a bit before installing Ubuntu), the adapter was autodetected - i could see my wireless network listed in the networks list dropdown, and lsusb showed it too.lsusb identifies "Bus 002 Device 002: ID 148f:2070 Ralink Technology, Corp. RT2070 Wireless Adapter"But i cannot connect to the network. When i select my network, it keeps trying to connect, but never succeeds in connecting.

i tried going through the forums for possible solutions, but most of them deal with how to get it working when the adapter is not detected, or when networks are not shown. Or they are for older Ubuntu versions.i use the same wireless network on my laptop (Ubuntu 9.04), and it has a WPA & WPA2 Personal security, with a password, which i've configured in the desktop as well.

View 1 Replies View Related

Fedora Networking :: Wireless-G USB Network Adapter Setup For 12

Jul 14, 2010

To setup a Compact Wireless-G USB Network Adapter (WUSB54GC) on Fedora 12 ?

View 1 Replies View Related

General :: Having A Belkin Wireless G USB Network Adapter But Can't Get On The Internet With It

Mar 11, 2010

I have a Belkin Wireless G USB Network Adapter but I cant get on the internet with it.The laptop is running Damn Small Linux.Heres what is going on and the code I typed:

ndiswrapper -i rt73.INF
ndiswrapper -l
modprobe ndiswrapper
iwconfig

ndiswrapper says the driver and hardware are present but iwconfig and ifconfig don't say anything.The wireless adapter works fine in windows 2000 and windows xp with the same driver.The green LED on the wireless adapter never flashes like it is supposed to.

View 3 Replies View Related

Ubuntu Networking :: Put USB 54Mbps Wireless Network Card Adapter Into Studio- 64 Bit?

Apr 20, 2010

May I put a USB 54Mbps Wireless Network Card Adapter into Ubuntu Studio- 64 bit, does the 64 bit Ubuntu Studio (9.10) support this usb wireless network card adapter? how to let it work in Ubuntu Studio 9.10

View 8 Replies View Related

Ubuntu Networking :: Rt73usb In 10.04 - No Wireless Adapter Shown In The Network Manager

Jun 25, 2010

I recently upgraded from Ubuntu 9.10 to 10.04 (both 64-bit) and my USB WiFi adapter which previously worked fine stopped working. The adapter is a Hama USB stick based on the Ralink rt73 chipset. I've tried using the Ralink drivers that come with 10.04 (both rt2800usb and rt73usb) but neither work. When I use rt2800usb, the adapter is recognized as interface wlan0, however I can't see any wireless networks. When I use rt73usb (and blacklist rt2800usb to avoid conflicts) I no longer have a wlan0 interface and there is no wireless adapter shown in the network manager. I've pasted in the results of lsmod, lsusb, and ifconfig -a (with MAC addresses removed) below.

[Code]....

View 3 Replies View Related

Ubuntu :: Belkin Surf & Share Wireless Network Adapter Not Working?

Jan 3, 2011

i have ubuntu 10.04 i believe and i cant connect to the intenret i guess its not detecting my wireless adapter. i cant try ethernet cord which prolly would work because i cant move pc to another room....is there any fix for this? i googled linux drivers but i cant find any...i do have the cd that came with the adapter.

View 1 Replies View Related

Ubuntu Networking :: Atheros AR5001X+ Wireless Network Adapter (rev 01) Not Working

Mar 3, 2011

I have a Toshiba MX35 laptop it's a little old but does the job. I'm have a problem getting the wireless to work. I can boot a live CD either Ubuntu 10.10 or Fedora 14 and they will see the wireless card. The card is Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter (rev 01).

I have Ubuntu 9.10 installed and that is the OS that is having the problem seeing the wireless. The computer will not handle Ubuntu 10.10 (at least it won't handle the desktop effects under Ubuntu 10.10) but handles them just fine under 9.10 and that's why I have 9.10 installed. I really need the Wifi to work because I'm going to travel in a few days.

View 5 Replies View Related

OpenSUSE Network :: Wireless Usb Adapter Freezing Computer WUSB54GCv3

Feb 1, 2010

Let me start by saying that with the previous kernel 2.6.31.5 when I opened network configuration, it didnt even recognize my card when i'd go to modules. After I updated to 2.6.31.8 it didnt recognize it until I installed the ralink-firmware 1.1.3.5. After that I could configure it using rt2870sta setting in modules. But once I restarted it would freeze after a few seconds after I could see the desktop on startup. I reconfigured the card to be 'manually' powered, but now it just freezes when I click on the access point I want to connect to. When it freezes the caps lock and scroll lock start blinking and the only way to turn off is holding the power

View 2 Replies View Related

OpenSUSE Network :: Configure Belkin Wireless USB Adapter (F7D2101)?

May 26, 2010

configure my Belkin Wireless USB adapter(F7D2101)? I attached the adapter and rebooted the system. I used the hardware info and it is listed but no drivers.

View 1 Replies View Related

General :: Wireless Network Adapter Recognized Or Driver Installed?

Jan 17, 2011

I am brand new to Linux and Ubuntu. However it was very easy and smooth to install and get updated using my wired ethernet connection. I am now trying to understand how to have my wireless network adapter recognized or driver installed. I will be searching around the forums but it suggested I make an initial post as a new user. I am using an older Dell Inspiron 2200. I believe the chipset in my wireless adapter is indeed Broadcomm, so hopefully that will help direct any responses.

View 2 Replies View Related

General :: Wireless Network Adapter Is Not Detected In Hp CQ40-416 Using Backtrack4?

Feb 19, 2010

I am a newbie in linux and I curious to learning all about linux, but I have a little trouble. I've just installed my first linux, its Backtrack 4 and my wirelesss network adapter was not detected..please help what I'm soppost to do..i'm using HP CQ40-416AMD Turion X2Broadcom 802.11 b/g WLAN Adapternote :

View 1 Replies View Related

Ubuntu Networking :: Belkin F5D7050 Wireless-G 54Mbps USB Network Adapter Setup?

Apr 13, 2011

I recently installed the latest and greatest Lubuntu 64 bit, because I like lxde and I am planning a system migration. (I am really starting to not like windows 7.) I have some linux experience. I wouldn't say I am awesome at it, but I am comfortable trying anything.

Example: I have used CENTOS 5.6 to make a linux machine server as a glorified router, with asterisks, SIP, SSH server, x windows, GNome, VNC, and a user authentication system. and get this I walked somebody through setting this up over the phone. I reopened the root account (I honestly got tired of typing sudo every other command is the only reason why I opened it.) I plan on closing it after we are done.

lsusb lists the wireless adaptor

Wireless Card Link

[[URL]

I have the driver CD. I installed ndiswrapper.I copied the files from my driver cd to my <home> Directory. Then installed the Windows XP version of the drivers using ndiswrapper -l <driver>. I then made ndiswrapper force the driver to the vendor ID of the wireless card. Using ndiswrapper -a <vendor ID> <Driver>(I did this last night and the vendor ID escapes me. I am at work now.)I finally ran depmod -a and modprobe ndiswrapperI goto the windows wireless driver application, and it shows the driver as loaded and the hardware as found.

However, it still does not list a wireless device in the network manager to where I can connect to my wireless. iwconfig does not show any wireless LAN, but it is still listed in lsusb. Also, the light that shows activity on the wireless device does not light up or blink at all. I have about 6 usb ports on my desktop and have tried everyone. The wireless card also works in Windows 7 64-bit On a strange side note. I do have internet access through LAN, (My laptop is atm a glorified wireless card .)

View 4 Replies View Related

OpenSUSE Wireless :: Can't Access Wep Encrypted Network With Linksys Wusb11 Ver 2.6 Net Adapter

Aug 9, 2011

I have installed Suse 11.4 from the Gnome liveCD, and I "can" access my home network when it is unsecured, however, I can't access it when WEP is turned on. Now, I know that WEP is insecure but there are devices on the network that only supports WEP so the router settings can't be changed. Also just for testing purposes i have tried the WPA2 encryption method to no avail (dmesg reports that the connection timed out). The only encryption method that looks promising is the open-wep encryption. When trying to connect to the network (with open-wep turned on) I have performed a bit of checking to see what is going on, now I don't know much about in-depth linux and stuff but, below are the outputs from lsusb, dmesg, iwconfig, and ifconfig.

lsusb

Code:
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 003: ID 077b:2219 Linksys WUSB11 V2.6 802.11b Adapter
dmesg

[Code]....

View 9 Replies View Related

Ubuntu Networking :: No Driver Claimed In Ndiswrapper - Atheros AR5001X+ Wireless Network Adapter?

Feb 26, 2010

I recently switched from Windows XP to a clean install Ubuntu Karmic Koala 9.10 but it seems to be quite a problem to get the wifi up and running. In Windows the nearby network all appeared in network connections but the same section in Ubuntu is empty. So I decided to go with the ndiswrapper guide to solve the problem with an unclaimed driver. After an entire day messing with my computer I'm still not close... Below follows excerpts taken from the Ndiswrapper guide with posted results from my computer. "ndiswrapper won't work until it thinks that your Windows drivers have been properly installed and that they are the appropriate ones for your wireless card. You can run the command: ndiswrapper -l"

result:

WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release.
WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in a future release.
net5211 : driver installed
device (168C:0013) present (alternate driver: ath5k)

So I've posted the result the name of my wireless card below: lspci -nn

Result:

00:00.0 Host bridge [0600]: VIA Technologies, Inc. CN333/CN400/PM880 Host Bridge [1106:0259]
00:00.1 Host bridge [0600]: VIA Technologies, Inc. CN333/CN400/PM880 Host Bridge [1106:1259]

[code]...

It seems like the network is disabled or unclaimed or both. What to do? I'm stuck after spending an entire day trying to install the wifi. I had no problems in Windows XP but it seems to be quite impossible in Ubuntu.

View 7 Replies View Related

Fedora Hardware :: Wireless Network Adapter Not Detected - Dell Inspiron E1750?

Jan 4, 2011

today my windows crashed and i decided to move into Linux.But here comes my biggest problem now, i cannot connect to wireless network but i am able to connect through wired connectionmine is a 10 year old computer so i think the card used is Intel PRO/Wireless 3945ABGi am using Fedora 14. please note that i know only very little in Linux so please respond accordingly

View 14 Replies View Related

Debian Configuration :: Using Azio Wireless PCI Adapter (Network Controller: RaLink Device 0701)

May 3, 2010

using this Azio Wireless PCI Adapter[URL] (Network controller: RaLink Device 0701)

View 11 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved