Ubuntu Networking :: Rt73usb In 10.04 - No Wireless Adapter Shown In The Network Manager
Jun 25, 2010
I recently upgraded from Ubuntu 9.10 to 10.04 (both 64-bit) and my USB WiFi adapter which previously worked fine stopped working. The adapter is a Hama USB stick based on the Ralink rt73 chipset. I've tried using the Ralink drivers that come with 10.04 (both rt2800usb and rt73usb) but neither work. When I use rt2800usb, the adapter is recognized as interface wlan0, however I can't see any wireless networks. When I use rt73usb (and blacklist rt2800usb to avoid conflicts) I no longer have a wlan0 interface and there is no wireless adapter shown in the network manager. I've pasted in the results of lsmod, lsusb, and ifconfig -a (with MAC addresses removed) below.
[Code]....
View 3 Replies
ADVERTISEMENT
Mar 3, 2009
I have been running FC8 on this IBM T23 with a D-Link wireless adapter. Using MadWifi this has worked fine with Network Manager disabled. But now I have nuked that installation and replaced it with FC10. Network Manager is nice, and I would like to use it. And it kind-of works. Network Manager recognizes my router and all my neighbor's routers, but I can't connect.
[Code]....
View 5 Replies
View Related
Jul 29, 2011
this is a brand new installation of 10.04 on a desktop. it's a dual boot with XP and the connection works on that side.i'm thrown off balance by the complexity of the situation... at least it is to me . i am able to see my wireless connection (along with my neighbor's). i enter the WPA password when prompted and for the next 5 minutes, it tries to connect with no success at the end.
Code:
francis@gandhi:~$ sudo lshw -c network
*-network:0
[code]...
View 2 Replies
View Related
Feb 5, 2010
Okay currently I am using a a Belkin F6D4050v1 usb wireless n card on a 32 bit intall of ubuntu 9.10. I have already installed ndiswrapper and installed the the rt2870.inf driver and rebooted. But i still have no wireless. when I use the command "sudo lshw -C network" all i see is my pci wired nic card"lsusb" the ID of the card is "050d:935a Belkin Components""sudo iwconfig" sayslo no wireless extensionsetho no wireless extensions
View 2 Replies
View Related
Nov 24, 2010
I recently reformatted and dual partitioned to both Windows 7 as well as ubuntu 10.10. Loading works fine and Windows 7 is 100% operational. I cannot seem to get my wireless network adapter to be read by Ubuntus 'Windows Wireless Drivers' gui. Here are the steps that I have done THUS far, to make sure that we are all on the right path. Before I go any further, my wireless network adapter is an old school WUSB11 Linksys Wireless Network Adapter (running version 2.6).
1) Downloaded and installed "ndiswrapper" from ubuntu's main website. I downloaded the common, utils and ndisgtk files and installed them accordingly.
2) I extracted these three files to the desktop of Ubuntu and accessed the terminal page.
3) From terminal I typed "cd Desktop" to change the directory to the desktop.
4) Next, I typed in "Sudo dpkg -i ndiswrapper-common_1.54-2ubuntu1_all.deb
Sudo dpkg -i ndiswrapper-utils-1.9_1.54-2ubuntu1_i386.deb
Sudo dpkg -i ndisgtk_0.8.5-1_i386.deb"
5) This installed Windows Wireless Drivers gui successfully and I can access it.
6) I have downloaded the driver files for the adapter from the cisco website and searched them for the required files needed.
7) After extracting the .INF file from the "Drivers" directory named "NETUSB.SYS" (I wasn't sure if the other associated files within the same folder needed to be present together with NETUSB so I moved everything to the desktop) I typed in "sudo ndiswrapper -i NETUSB.inf". After accessing the Windows Wireless Drivers gui I have noticed that the 'netusb' driver is present yet under it, the system states "Hardware present: No". This leads me to believe that maybe I installed incorrectly or my "fireware?" is not present? I was reading through the installation guide posted on the ubuntu website that in addition to the .INF file we also need the BIN file(s)? and SYS file(s)?.. The folder with the drivers for my adapter contains a BIN file but it is not within the "Drivers" section of the folder.
9) Upon mousing over the network Icon naturally my hardware is still not present.
10) From what I gather after the system finds the hardware I am to write into the terminal
[Code]....
View 2 Replies
View Related
Aug 30, 2010
I am severe wireless problems with Ubuntu 10.04 on my laptop.(Spec below)
I have just performed the first clean install since new. Installed a new Hard Drive as well. The machine and wifi was fine under Ubuntu 9.04.
It is booting much faster now but the wifi keeps dropping off.
Spec:
Machine - Acer Aspire 4310
Wireless card - *-network
description: Wireless interface
product: AR5001 Wireless Network Adapter
vendor: Atheros Communications Inc.
[Code].....
View 2 Replies
View Related
Feb 3, 2010
I have a Belkin Enhanced Wireless USB Network Adapter Model # F6D4050 v2. The drivers are for windows but the windows wireless drivers app doesnt work. I see a tutorial for a linksys that appears to have the same chipset, but I am not sure if any of the steps need to be modified, also my kernel is a bit different. Here is my kernel:
[code]...
View 1 Replies
View Related
Aug 31, 2010
I have an HP Pavilion dv5 1002nr laptop running Vista. I decided to install Ubuntu using the windows installer, which did install well, but I decided that it wasn't for me, and uninstalled it. Now, my wireless adapter which is a Atheros AR5007 802.11b/g can see the network, find networks by itself, and is supposedly installed correctly according to Vista, cannot connect to any networks at all despite being able to see them and acquire a signal strength. Up until installing Ubuntu I have never had an issue like this. Other devices have no trouble connecting to this network, and I am currently using a Netgear wireless usb dongle to connect to the very network that my Atheros can not connect to.
View 2 Replies
View Related
May 17, 2010
How do i get my xbox 360 wireless adapter to work on ubuntu?
View 2 Replies
View Related
Jul 9, 2010
I just got a new AZiO AWU212N 802.11n wireless usb adapter (linked below). One of the product reviews said that it works with Ubuntu if you upgrade to the .34 kernel so I thought it would be a good buy. I updated my kernel and Ubuntu detects that there is a wireless adapter, but doesn't detect any networks. My old wireless-g adapter can connect just fine, so I don't know what the problem is.
http://www.newegg.com/Product/Produc...82E16833340018
View 3 Replies
View Related
Feb 15, 2011
I am trying to install a Star Tech PEX300WN2X3 wireless card but I'm completely lost. The installation Cd has 2 tar. files with the linux drivers but I'm just clueless as to what to do with them.
View 9 Replies
View Related
May 19, 2011
i just installed Ubuntu 11.04 64bit on my desktop. i have a TP Link TL-WN321G (Ver 4.0) wireless usb adapter to connect to my wireless network (i used to use it with Windows XP).As expected (i'd read up a bit before installing Ubuntu), the adapter was autodetected - i could see my wireless network listed in the networks list dropdown, and lsusb showed it too.lsusb identifies "Bus 002 Device 002: ID 148f:2070 Ralink Technology, Corp. RT2070 Wireless Adapter"But i cannot connect to the network. When i select my network, it keeps trying to connect, but never succeeds in connecting.
i tried going through the forums for possible solutions, but most of them deal with how to get it working when the adapter is not detected, or when networks are not shown. Or they are for older Ubuntu versions.i use the same wireless network on my laptop (Ubuntu 9.04), and it has a WPA & WPA2 Personal security, with a password, which i've configured in the desktop as well.
View 1 Replies
View Related
Jul 14, 2010
To setup a Compact Wireless-G USB Network Adapter (WUSB54GC) on Fedora 12 ?
View 1 Replies
View Related
Apr 20, 2010
May I put a USB 54Mbps Wireless Network Card Adapter into Ubuntu Studio- 64 bit, does the 64 bit Ubuntu Studio (9.10) support this usb wireless network card adapter? how to let it work in Ubuntu Studio 9.10
View 8 Replies
View Related
Mar 3, 2011
I have a Toshiba MX35 laptop it's a little old but does the job. I'm have a problem getting the wireless to work. I can boot a live CD either Ubuntu 10.10 or Fedora 14 and they will see the wireless card. The card is Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter (rev 01).
I have Ubuntu 9.10 installed and that is the OS that is having the problem seeing the wireless. The computer will not handle Ubuntu 10.10 (at least it won't handle the desktop effects under Ubuntu 10.10) but handles them just fine under 9.10 and that's why I have 9.10 installed. I really need the Wifi to work because I'm going to travel in a few days.
View 5 Replies
View Related
Apr 13, 2011
I recently installed the latest and greatest Lubuntu 64 bit, because I like lxde and I am planning a system migration. (I am really starting to not like windows 7.) I have some linux experience. I wouldn't say I am awesome at it, but I am comfortable trying anything.
Example: I have used CENTOS 5.6 to make a linux machine server as a glorified router, with asterisks, SIP, SSH server, x windows, GNome, VNC, and a user authentication system. and get this I walked somebody through setting this up over the phone. I reopened the root account (I honestly got tired of typing sudo every other command is the only reason why I opened it.) I plan on closing it after we are done.
lsusb lists the wireless adaptor
Wireless Card Link
[[URL]
I have the driver CD. I installed ndiswrapper.I copied the files from my driver cd to my <home> Directory. Then installed the Windows XP version of the drivers using ndiswrapper -l <driver>. I then made ndiswrapper force the driver to the vendor ID of the wireless card. Using ndiswrapper -a <vendor ID> <Driver>(I did this last night and the vendor ID escapes me. I am at work now.)I finally ran depmod -a and modprobe ndiswrapperI goto the windows wireless driver application, and it shows the driver as loaded and the hardware as found.
However, it still does not list a wireless device in the network manager to where I can connect to my wireless. iwconfig does not show any wireless LAN, but it is still listed in lsusb. Also, the light that shows activity on the wireless device does not light up or blink at all. I have about 6 usb ports on my desktop and have tried everyone. The wireless card also works in Windows 7 64-bit On a strange side note. I do have internet access through LAN, (My laptop is atm a glorified wireless card .)
View 4 Replies
View Related
Jan 24, 2011
I am a Windows refugee who discovered Ubuntu as a way to save my files from my virus-ravaged computer. Had no installation discs for Windows, so when I had to wipe my hard drive and start over, I decided to give Ubuntu a try. I've had mixed success, but that's another post...
Right now, the problem is that I installed 10.10 two weeks ago and was able to connect to the Internet with no problems - until yesterday. Suddenly, our wireless network (the only one in the vicinity) does not come up as available in Network Manager. In fact, the entire wireless option disappeared. I know there are many posts and threads on here about this, but weeding through them trying to find an answer is more frustrating than actually dealing with the problem. I know the router works because I can post on this forum from the Macbook. I really like Ubuntu and would like to keep using it, but not being able to connect to the Internet now on top of the other issues I've had is making me doubt I want to continue down this Linux road.
P.S. When I attempted an analysis through System Testing, it said something about there being no proprietary drivers?
View 2 Replies
View Related
Feb 26, 2010
I recently switched from Windows XP to a clean install Ubuntu Karmic Koala 9.10 but it seems to be quite a problem to get the wifi up and running. In Windows the nearby network all appeared in network connections but the same section in Ubuntu is empty. So I decided to go with the ndiswrapper guide to solve the problem with an unclaimed driver. After an entire day messing with my computer I'm still not close... Below follows excerpts taken from the Ndiswrapper guide with posted results from my computer. "ndiswrapper won't work until it thinks that your Windows drivers have been properly installed and that they are the appropriate ones for your wireless card. You can run the command: ndiswrapper -l"
result:
WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release.
WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in a future release.
net5211 : driver installed
device (168C:0013) present (alternate driver: ath5k)
So I've posted the result the name of my wireless card below: lspci -nn
Result:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. CN333/CN400/PM880 Host Bridge [1106:0259]
00:00.1 Host bridge [0600]: VIA Technologies, Inc. CN333/CN400/PM880 Host Bridge [1106:1259]
[code]...
It seems like the network is disabled or unclaimed or both. What to do? I'm stuck after spending an entire day trying to install the wifi. I had no problems in Windows XP but it seems to be quite impossible in Ubuntu.
View 7 Replies
View Related
Apr 30, 2010
I have 10.04 installed on my HP MiniNote Netbook. If I plug it into the the ethernet directly, all is well, but if I only use the wireless, i get no DNS servers. And one of my wireless networks is on the same router as the wired connection. Also, wireless works just perfectly on my MacBook Air. So, I do not think it is the router. So why am I not getting DNS addresses? How would I set them manually? I can't figure out how to start network manager.
View 2 Replies
View Related
Jul 3, 2011
I want to set up a static IP on my laptop that connects via wireless to my home network. I have 11.04 installed on my laptop. When I try to use the manual IPv4 setting in the network manager the save option gets greyed out. I tried to edit the /etc/network/interfaces file but all the examples I could find on the net refer to eth0. I tried replacing this with wlan0 but this did not work. I tried installing wicd but I kept getting "Bad Password" errors even though I know the password is correct. A number of people recommended uninstalling network manager to get wicd to work but many other posts said that uninstalling network manager didn't help so I didn't want to go ahead and uninstall unnecessarily. Besides I figure if Ubuntu is distributed with network manager there must be a reason for having it. So what do I do to get a static IP address for the client on a wireless connection?
1. I went to network manager and selected "Connection Information" On the information window I saw the following:
IPv4
IP Address: 192.168.1.6 (This is the item I wanted to change and make static)
Broadcast Address: 192.168.1.255
Subnet Mask: 255.255.255.0
[code].....
2. I went to network manager and selected "Edit Connections"
3. I selected the wireless tab and then the wireless network I wanted to edit
4. I clicked on the edit button and then I clicked on the IPv4 settings tab.
5. I changed method from Automatic (DHCP) to Manual
[code]....
View 8 Replies
View Related
Feb 8, 2010
To start off I have a Rosewill rnx-n2x wireless adapter and a Dlink 4500 router. The problem is, the wireless network manager detects every wireless router in the neighborhood, except mine. I see this persons, and this persons, but no "My router Not yours". I even tried doing the hidden network setup and still nothing.
I have read that the rnx n2x isnt supported by linux, although I've seen solutions to make it work (which didn't work, mkdir command kept getting denied during make) link to what I'm talking about: [URL]. What I don't get though, is that if the rnx n2x isnt supported by linux, wouldn't I not be getting my neighbors connections to begin with?
View 1 Replies
View Related
May 8, 2010
I'm not sure if I have two seperate issues or one inter-related issue. The Network Manager applet wasn't appearing in the tray, found out it wasn't installed. Installed, still didn't appear. Tried installing WiCd, WiCd did appear but couldn't find any networks. I had installed restricted drivers previous, decided it was worth another look. Found that Broadcom STA Wireless Driver wasn't installed. Tried to install, it said it couldn't and said I should review the var/log/jockey which is....excessively long.
View 2 Replies
View Related
Sep 11, 2010
I'm trying to search for more wireless networks but i cannot find a way to make network manager search for more wireless networks. It only displays 2 wireless networks and none of them is mine, even though I've got my wireless router at less than 1 meter from my PC.
View 2 Replies
View Related
Sep 19, 2010
A couple of weeks ago my laptop's wifi started acting up, to the point that it didn't function. When I click the nwManager icon to being up a list of available networks, it is empty. If I try to create a new network, with the credentials of my modem, it appears to work, and asks for the password. After I enter the password, it seems to work for about 30 seconds (much longer than normal) but then it prompts me again for the password. This cycle continues indefinitely.
I'm running Karmic on a Dell i1525. how to find out what wireless card I have.
View 4 Replies
View Related
May 29, 2011
I've installed ubuntu 10.04 on a hp mini 110. I've used netbook remix on this same computer and had no problems with a wireless connection. In this case, network manager shows wireless disabled. I have installed the Broadcom B43 Wireless drive from Adminstration->Hardware drivers. No help! ifconfig does not
show eth1 and lspci tells me that the Broadcom BCM4312 Network controller is present.
View 9 Replies
View Related
Sep 26, 2010
I just reinstalled Ubuntu Lucid Lynx and an old problem has come back. For some reason I couldn't fix it even in my previous installation. The problem is the top gnome panel. See the photo below: As you can see, the network icon is not shown properly while the Me menu is being shown twice. I can't even restart or log out or shut down at this situation without pressing the keystroke to turn the power off.
View 9 Replies
View Related
Dec 10, 2010
I want to try to get wireless access to the wifi router with the xbox360 wireless network adapter.Is this possible?
View 1 Replies
View Related
Feb 10, 2010
I deleted all APs in my Wireless Section of network manager. After that, the whole network manager icon disappeared. I added the icon back on the panel, but I don't think its the right one. It doesn't do the two green cicles thing when I connect my ethernet wire in. It also doesn't show any wireless AP when I left click on the icon. It doesn't even have an X mark on the bottom left of the icon when no network is detected
View 1 Replies
View Related
Apr 30, 2011
So, after doing a 'yum update', I minimized the terminal and completely forgot about it - so I accidentally went ahead and suspended my laptop before it had finished. I resumed my laptop and noticed that yum hadn't finished 'cleaning up' the packages. Nevertheless, yum continued and the process finished. After an hour or so use of the internet (wirelessly), all of a sudden the wireless network disconnected, and NetworkManager crashed. I rebooted my computer only to find that NetworkManager now says that my 'firmware is missing' for my wireless card.
View 6 Replies
View Related
Sep 5, 2011
I'm having problems with my wireless card. The network manager won't allow me to turn it on. It is working in windows and in ubuntu, but I can't get it to turn on under fedora. I'm using a Lenovo B570 laptop and it uses the Centrino Wireless-N 1000 for wireless.
View 5 Replies
View Related
