I regret updating to 11.04. It broke everything during the update. I cannot get the broadcom wireless chipset to work more than 10 seconds, No matter how much research I do here. I have not been able to work within my GDocs for the last three days. Can I restore back to my 10.10 settings? I have an acer laptop.
View 3 RepliesHere is what I have as far as hardware goes:
Compaq Presario V2000
- PROCESSOR: Intel Pentium M 710 -- 1.4 GHz
- RAM 2 GB
- HD 80 GIG
- Duel booting XP Pro with Ultimate Edition 2.8 (I understand this is built from Ubuntu 10.10)
- lspci -vnn | grep 14e4 yields the following:
Code:
03:00.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
I have followed to the tee this guidance: [URL]
I tried the installing b43 drivers with internet (using ethernet)
I tried installing off the DVD using the no internet option
I even tried installing the STA drivers even though I know the 4318 chipset is not mentioned as a supported chipset.
All of these were loaded/extracted with no errors via terminal following the guidance to the letter. Now here is a problem I have not read that anyone else has run into. (maybe I just missed it). When I go: System > Administration > Additional Drivers the only additional driver that shows up is "Software Modem". I can't for the life of me figure out why the b43 and STA drivers are not showing up to activate. I can install drivers all day long, if I can't activate them, it really does become a moot point.
some time ago I installed 8.10 on my x20 thinkpad. I at the time was trying to get it going on a Netgear WG511 v2 card. I was eventually successful in getting it going with ndiswrapper and all has been happy until...
I decided to give my laptop to an elderly friend for his first computer. He is living in a location where (for a variety of reasons) he is sharing a network connection to the internet with a few people. The protocol there WPA2 TKIP (IIRC) and no matter what the bloody thing won't connect. Here at home I run a different setup so its not a big deal
So, I thought I'd try another card to get it going there. I chose a "Aironet" card (badged a Dell 4800 LT) and tried to install this on 8.10
I expected it would install out of the box, but did not "seem to".
I followed the steps on this page, but still it won't connect to my WiFi at home (which I am using to connect to with this x31 thinkpad)
I am using Network Management Applet 0.70 and this works fine with the Netgear card, even showing all the local networks it finds.
When I plug in the Dell card it blinks the activity light and the status light in seemingly meaningful ways, but nothing seems to connect and I find nothing listed in the Network Applet.
I suspect that the OS is discovering the card as when doing an iwconfig I find two entries that would be that card:
eth1 and wifi0
iwlist scan returns:
which makes me think two interfaces are taking the same hardware...
iwconfig returns idential results for eth1 and wifi0
I'm working on Lucid, in HP Pavilion 9730us laptop.
My wireless broadcom card was working just fine until now as i installed it with the Hardware Devices manager, Today i put a new ALFA AWUS036H usb card to work with aircrack. both cards were working together for a while, but as i started playing around with aircrack the broadcom card of the HP has stopped working.
I made a mistake and followed the aircrack tutorial for R8187 / ieee80211 stacks driver, while i'm using RTL 8187 / mac80211 stack drivers, and blacklisted the RTL8187 , rebooted and then both card didn't work. I un-blacklisted it, and the ALFA is working but the broadcom not!
iwconfig shows me only one wireless card on wlan0 the blue light showing activity in the HP card doesn't go on.
Tried to uninstall and reinstall broadcom drivers, still no change.
I've just installed Ubuntu on 2 computers, and I'm new to it. However I'm not new to computers. The problem I'm currently running into on one of the computers is that the wireless will not detect any connections, despite there being many. The computer is a HP Compaq v6203AU using the wireless card Broadcom BCM4312 [14e4:4312]. I've went through dozens of walkthroughs, encountering errors in every single one of them, I've spent 8 hours on this one problem and extremely frustrated. It seem to be a problem with the driver that comes as default, and I'm lost at what to do.
The terminal command "lspci -nn | grep 14e4" returns the following:
03:00.0 Network Controller [0280]: Broadcom Corporation BCM4312 802.11a/b/g [14e4:4312]
ifconfig returns the following:
eth0 Link encap:Ethernet HWaddr 00:23:8b:b2:ab:d3
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:20 Base address:0x8000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:96 errors:0 dropped:0 overruns:0 frame:0
TX packets:96 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:7072 (7.0 KB) TX bytes:7072 (7.0 KB)
The computer has no internet access as there is nowhere to connect except through wireless.
I decided to start of with Debian. I'm having trouble getting my wireless connection to work. I think i need drivers or something, i can't make a wireless connection. And it is a bit difficult for me, as i am new to Linux, and I'm not sure what I'm doing when i am writing these commands.
My wireless card is a Broadcom Corporation BCM43142 802.11b/g/n
I have been using Raspberry PI a little, so i am familiar with the terminal.
I've been reading up on how to get the Broadcom BCM4312 802.11b/g on my Dell Inspiron 1525 to work with OpenSUSE and I've tried everything, I've even re-installed the OS 3 times as I seemed to keep screwing something up. I've tried doing what it says in this thread
Install Broadcom Drivers from Packman
I thought I'd installed the write drivers with this code:
Code:
zypper in broadcom-wl broadcom-wl-kmp-default
For those of you that prefer open-source solutions, the b43 code to drive BCM432X 802.11n devices has just come to life. It can now scan and associate. Tests for throughput will come soon. These revisions to the driver will be in kernel 2.6.38, thus not in openSUSE until the next release after 11.4.
View 1 Replies View RelatedI have been trying to get my Broadcom BCM4328 to work properly on openSUSE 11.2 (kernel 2.6.31.5). Finally, after installing the wl kernel module, I managed to get it working when a run the following commands after a reboot:
sudo /sbin/modprobe -r b43 b44 ssb wl
sudo /sbin/modprobe wl
sudo /sbin/modprobe b44
sudo /etc/init.d/network restart
My question is how can I automate the above commands, i.e. create a startup script to initialise the wireless adapter properly without the need to manually reload the kernel modules?
Well I see there is a lot of people which have problems with BCM4312 I read that topics but my problem kind of different..I installed 11.3 few day ago at my job. Everything was just fine...First of all I'm installed firmware
Code:
install_bcm43xx_firmware
Wireless worked fine...
[code]...
Wifi works on 11.3 with installed the broadcom-wi & broadcom-wl-kmp-desktop,but this trick doesn't work on this new 11.4.
View 9 Replies View RelatedI am still encountering problems getting the Broadcom 4321 chipset to work on my Fedora 13, even after using this guide, this guide and another guide on ndiswrapper.
To answer the standard questions:
Code:
Code:
Code:
Code:
and finally
Code:
But no wlan device or anything else.
I recently installed Suse 11.4 on my Dell Latitude 2110 netbook using the KDE live distribution, and, after that, the Broadcom wireless ceased to work. To enable the wireless connection, I have to press Fn + F6. If I do it now, the wireless led indicator turns on for a couple of seconds, then turns off again. Moreover, the option to enable the wireless connection in the network manager is greyed out
lspci output:
Code:
0c:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01)
iwconfig output:
Code:
wlan0 IEEE 802.11abgn ESSID:off/any
Mode: Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit: 7 RTS thr: off Fragment thr:off
Encryption key: off
Power Management: off
dmesg output:
Code:
[8.330963] brcm80211: module is from the staging directory, the quality is unknown, you have been warned.
[8.362403] brcm80211 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[8.362422] brcm80211 0000:0c:00.0: setting latency timer to 64
output of rpm -qa | grep broadcom:
Code:
broadcom-wl-kmp-desktop-5.100.82.38_k2.6.37.1_1.2-7.pm.8.1.x86_64
broadcom-wl-5.100.82.38-7.pm.8.1.x86_64
I'm very new to Debian (and Linux in general), and am currently taking a Linux course at college... I'm trying to get Debian running on my MacBook Pro (late 2009 model) and it's been complicated but I've got the operating system installed on it... I'm just having a few problems, the biggest right now of which is my wireless card, which doesn't work. So, I found instructions on the Debian Wiki for getting the driver for it, but it's not compiled already and I have little knowledge of manually installing stuff through Linux...
View 2 Replies View RelatedI have installed Fedora 15 on a Mac mini 2.4. Everything works fine except the audio and wireless devices.
lspci shows this:
In the gnome, the network option only shows the wired connection. I tried to do yum install kmod-wl which downgraded the graphic display and didnt help in wireless issue. I reinstalled nvidia driver. the lspci is after doing all this stuff.
I wireless network card is Broadcom Corporation BCM431, but is doesn't work after I update kernel from
2.6.29.6-217.2.7 to 2.6.29.6-217.2.8.
Linux localhost.localdomain 2.6.29.6-217.2.7.fc11.x86_64 #1 SMP Fri Aug 14 20:53:08 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux
I have an intel 5300 wireless chipset which is not supported in kernel 2.6.25. I am currently using opensuse 11.0, I downgraded from 11.1 since I faced so many other problems. can I setup my wireless driver under kernel 2.6.25? if so, how could i do this?
View 7 Replies View RelatedIt looks like my laptop's wireless chipset (Broadcom) has/is dying. It won't work anymore on my Lucid install whereas it was working perfectly. The warrenty is long expired.
lspci brings up nothing about it anymore, it once did.
I booted my laptop into Win7 and it no longer finds it either. The manual slider switch on my HP Pavillion dv6000 is in the on position but the light is yellow.
It will very rarely work on Win7 now.
I can't afford a new laptop just now so it looks like I need an external wireless adaptor. I have (open busses) USB, cardbus/54, and a small firewire port. It does not pcmcia or other busses.
Any particular chipsets to look for or avoid?
I've been running Karmic since it was officially released on my Dell Studio 17 (specs are in my signature) with a Broadcom wireless half mini wireless card.hen I installed Karmic, it gave me the option to install proprietary drivers for my video card as well as 2 Broadcom drivers, STA and one of the BC43 drivers. I installed all of these, and the only problems I had were with the audio. I spent a few days troubleshooting the audio and finally got PulseAudio set up for my card.
Almost 3 months later, I was making use of my wireless network at home, as I had done plenty of times over the previous 3 months, when I closed the lid (thus putting the computer into sleep mode) and took it to the hospital to stay with my fiancé¥ after her surgery. When I got to the hospital, I couldn't get their network to show up. Network Manager didn't even recognize the network. We had also brought my fianc饧s laptop (same machine with a slightly less powerful CPU and only 4 GB of RAM). She is running Windows 7, which detected the hospital's network with no problems.After trying to ad-hoc the hospital network with no success, I finally just gave up and played Sudoku and toyed with some graphics stuff in GIMP until we came home. Upon returning home, however, I was shocked that my card didn't even detect our home network.
I have been unsuccessful for the past 3 days in getting Network Manager to identify our wireless network. The wired network connects without issue and I am able to make use of a USB Belkin adapter, which identifies all 7 of the various wireless networks in my neighborhood, including our home network.While I would be able to simply carry my Belkin adapter with me in order to make use of wireless networks, I would really like to solve this problem with my Broadcom adapter. I've gone through the Ubuntu Wireless Network Troubleshooting guide, but I still can't get it to workOutput of lshw -C network:
Code:
*-network
description: Wireless interface
[code]...
I can't use my wireless card in slack 13.1 (slack64-current). Looking at the dmesg output I saw that the firmware was missing, so I download it from ralink website.After this I was able to up it with ifconfig. I also was able to see my network with wicd, but after connection I can only transfer very few packets and network becomes unresponsive, no traffic.In slack64 13.0 this same card works fine. I don't even need to install a firmware. how I can make this work in slackware64-current?
View 6 Replies View RelatedDoes the rt61 dlink wifi adapter work with slackware 13?
Code:
No wireless networks detected with AR5001 chipset
View 1 Replies View Relatedthis is my first attempt to get into Linux (10.04 Lucid Lynx), and I'm eager to learn. The problem is however that i can't connect to the internet using my USB wifi dongle (Jensen 25150). I've tried what this link says:I've tried to blacklist rt2800usb, rt2x00lib, rt2x00usb and rt2870sta and to load "/etc/modules/rt3070sta", but no luck in that, so I simply do not know what to do next. Perhaps I haven't blacklisted them the right way? I've typed in the commands and saved Gedit and closed it. Is that the right way?
View 2 Replies View RelatedI have a HP Pavilion dv2000 and can not figure out what chipset I have.
/sbin/lspci brings up the following
bunnyman@linux-bqo4:~> /sbin/lspci
00:00.0 Host bridge: Intel Corporation Mobile Memory Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile Integrated Graphics Controller (rev 0c)
00:02.1 Display controller: Intel Corporation Mobile Integrated Graphics Controller (rev 0c)
[Code]....
where I can get the .inf file from? I took windows completely off of the computer and dont want to reinstall it just to get the driver.
Perhaps this is sheer ignorance, but i just cant figure out which wireless chipset i´ve got. Its irrelevant to say that my wireless conection doesn´t authenticate (repeating the process without end). So this is the output of lspci:
linux-wghx:~ # lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 671MX
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SiS AGP Port (virtual PCI-to-PCI bridge)
[Code].....
How do you find one that runs in USB and how do you find it when it runs from a pci port. i already know that you might be able to find the kind of driver that is required to run the device
Lots of people have accomplished this by using aircrack but some operating systems can't install aircrack (not to mention that the use of some software is illegal depending on where you live) so i want an alternative.
I am getting ready to buy a wireless N adapter for my computer but I want to make sure its natively supported. I don't want to have to use ndiswrapper or manufacturer supplied drivers. I have been looking on newegg and I think I have narrowed it down to two choices. One has the Atheros AR9285 chipet and the other has the Realtek RTL8188RE chipset. I am fairly certain that the Atheros is natively supported since according to the newegg reviews it is. However the Realtek one is cheaper but I can't seem to find any information on whether or not its supported.
View 1 Replies View RelatedI just installed 10.10 on a Jetway HBJC600C99-52W machine. It has the NVIDIA ION2 chipset. Through a lot of struggles, I have managed to get most of the computer working well with Linux. The part that I'm still struggling with is the remote control. With Ubuntu out of the box, perhaps about 1/3 of the buttons are recognized. From additional research, it looks like lirc is supposed to address this issue. I tried installing lirc however, after installation the only thing that shows up is /dev/lircd. I was expecting something like /dev/lirc0. I've tried is via
sudo apt-get install lirc
and then I picked the Windows Media Center receiver
I also tried what was in this thread [URL] however, that seems to be on a different jetway model, an NVIDIA ION chipset instead of an ION2 and the driver install for the IR receiver didn't work for me. I was wondering if anyone had success installing lirc and getting all the keys on their remote working.
I am running FC13 on a Compaq Presario 2100 using a Broadcom BCM4306. I was able to get it running thanks to Fedora Unity Project. But It's a very unstable connection. I don't know what settings to adjust or enable or disable. It's not my router, this is the only wireless connection in the house that I have trouble with.
View 1 Replies View Relatedwhen it comes to openSUSE but I am earnestly trying. I installed the openSUSE OS on my HP dv6000 laptop, but it does not seem to recognize my wireless card (which is a Broadcom 4311).
View 7 Replies View Related