How do you find one that runs in USB and how do you find it when it runs from a pci port. i already know that you might be able to find the kind of driver that is required to run the device
Lots of people have accomplished this by using aircrack but some operating systems can't install aircrack (not to mention that the use of some software is illegal depending on where you live) so i want an alternative.
I'm running Debian Lenny. I want to get a wireless card working. Spent ages trying to get my betgear WG111T wireless dongle to work with ndiswrapper with no luck so I'm going to fork out for a wireless card. I've googled extensively but haven't really found a satisfactory answer. Is there a wireless card/chipset that I can count on working fairly easily or even better out of the box with Lenny?
View 3 Replies View RelatedOut of curiosity, in linux, how do we check:
- The make/type of ethernet card
- The wireless chipset
- The video card
Used in a computer?
Ok a little confused here. I got this working in f14 no problems but anyway. I have a wireless usb net card with a realtek 8192su chipset and of course it is not recognized.Dloaded driver from realtek unzipped tarball. Ran make clean and no errors then ran make all and this is what I get same with make or make install.
Code:
[root@donnie rtl8712]# make all
make ARCH=i386 CROSS_COMPILE= -C /lib/modules/2.6.38.6-26.rc1.fc15.i686/build M=/usr
[code]....
I'd like to know how can I find a Linux wirelles driver for wireless Belkin card.
View 1 Replies View RelatedWhere can I find a driver for this pc wireless card? And how do I install it?
View 1 Replies View RelatedI have an intel 5300 wireless chipset which is not supported in kernel 2.6.25. I am currently using opensuse 11.0, I downgraded from 11.1 since I faced so many other problems. can I setup my wireless driver under kernel 2.6.25? if so, how could i do this?
View 7 Replies View RelatedI have been running F13 since it came out, with the wireless working fine since I got it working (using the RPM Fusion repository, broadcom-wl-5.60.48.36-1.fc13). Since I updated software (without reading what was to be updated), yesterday, I am unable to even find wireless networks, although I am, as you can see, able to access through eth0 It is not a hardware problem, as I can not only find them, but access them on Ubuntu 9.10 live disc. Below is my lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
[code].....
I have installed open suse 11.3 with no issue, but I can't find the dirvers for the wireless network card/
Wireless, Half Mini-Card, DW1520
I know some wireless card can work in Master Mode but it seems use madwifi driver. I know madwifi doesn't support usb dongles find a usb wireless card which can work as AP under Ubuntu. I have check this list [URL] I am not sure if ar9170usb.ko and its device support Master MOde.
View 6 Replies View Relatedive just installed the aircrack package in my dell vostro 1310 which i bought with its ordinary wireless card ( hell knows what it is. couldn't find..).At the very first time while trying to reach my wireless internet i was using backtrack 4 and i was not sucesfull.. that would be good normally, but it was not. because i couldnt do it cuz my wireless card wasnt being recognized by airmon..so i tought..i can use my wireless with ubuntu... then i got ubuntu again.. and intalled the aircrack.. as i run it i found ou t that still it wont find my wireless card...do i need any further config. to make it work with aircrack ??i can only find eth0, which is my wired network device....
View 1 Replies View RelatedI'm new to Ubuntu. Today, I took my old Compaq Presario V3010US and gave it life with Ubuntu 10.04. The hard drive was erased and replaced with the Linux OS stuff. Ubuntu recognizes most of the hardware except my Broadcom wireless card. I find this to be a pain because i'm a newbie to linux stuff. Anyway, can anyone help me fix this? I thank you for your time reading this.
View 1 Replies View RelatedI cant get openSuse to find my wifi adapter or it does not have the driver installed.
My wifi adapter is the Realtek RTL8191SE 902.11b/g/n
I found a linux driver on the internet, but it asked me to run make in the console and when I did so it said that it couldn't find make.
how to install make from openSuse without the internet (I'm using my windows partition).
I can not install a driver for device EDUP WU2070. I have a disk with a driver for linux general. I don't know how to compile a makefile. My OS 11.3v doesn't see a device.
But when I run in Live CD mode all drivers install automatically and my WI-FI device work properly.
Any opinions on which of the PCMCIA wireless cards work the best out of the box? I currently have a USB wireless adapter but want to get rid of it and use my PCI slot on the laptop. I am currently running lucid. I would rather not have to mess around with NDISWRAPPER again, something that has a native linux driver would be great.
View 2 Replies View RelatedI have been trying to find a wireless card that will readily work with Ubuntu 10.04 Desktop. Preferably an +802.11 N with an indoor range of between 300 to 400 ft. with possibly two antennas. Am finding many that say linux on the box but find that it ain't so. Also most times with no instructions or very convoluted process that results in errors.
View 1 Replies View RelatedI'm trying to find a driver for my wireless card (Atheros AR928X) and I think it's ath9k what I need. As far as I know there isn't a linux driver for it, so I installed ndiswrapper to use a windows driver instead. The problem is that when I type modprobe ndiswrapper I get "bash: modprobe: command not found" (even as root). I know I'm missing something about modprobe, but I can't find any help on google. Anyway, I installed ndisgtk next, because I thought it would be easier, but when I go to System> Administration> Windows Wireless Drivers I get a message "Unknown error".Do you have any ideas on how I'll make ndiswrapper work?
View 3 Replies View RelatedWhere to look to find out which chipset my video card uses and how much memory it has? I also need to find out which motherboard I have and the BIOS version. I know these are fairly elementary questions, but school starts for me tomorrow and I don't have a lot of time to mess with a lengthy search. I just plan to update my BIOS, and if that doesn't solve my hardware issues I will create an xorg.conf file and force my machine to use a decent setting. I've been having researching this thoroughly and have a firm understanding of what's going on, but I'll be damned if I can't remember these basic commands.
View 4 Replies View RelatedHow do I know if my intel chipset graphics card thing is installed?.
View 1 Replies View Relatedsome time ago I installed 8.10 on my x20 thinkpad. I at the time was trying to get it going on a Netgear WG511 v2 card. I was eventually successful in getting it going with ndiswrapper and all has been happy until...
I decided to give my laptop to an elderly friend for his first computer. He is living in a location where (for a variety of reasons) he is sharing a network connection to the internet with a few people. The protocol there WPA2 TKIP (IIRC) and no matter what the bloody thing won't connect. Here at home I run a different setup so its not a big deal
So, I thought I'd try another card to get it going there. I chose a "Aironet" card (badged a Dell 4800 LT) and tried to install this on 8.10
I expected it would install out of the box, but did not "seem to".
I followed the steps on this page, but still it won't connect to my WiFi at home (which I am using to connect to with this x31 thinkpad)
I am using Network Management Applet 0.70 and this works fine with the Netgear card, even showing all the local networks it finds.
When I plug in the Dell card it blinks the activity light and the status light in seemingly meaningful ways, but nothing seems to connect and I find nothing listed in the Network Applet.
I suspect that the OS is discovering the card as when doing an iwconfig I find two entries that would be that card:
eth1 and wifi0
iwlist scan returns:
which makes me think two interfaces are taking the same hardware...
iwconfig returns idential results for eth1 and wifi0
i have a toshiba satellite p500 laptop which seems like it shold either have the intel hm55 express chipset or the pm55 i checked in win7 and cpuz says it is pm55 while pc wizard says it is hm55 ( though pc wizard seemed to be wrong with some other stuff as well) here is the so-called "detailed specs" from toshiba
[Code]....
Where can i find driver for Dell Wireless 1397 802.11b/g Half Mini Card. I'm using CentOS x86_64.
View 9 Replies View RelatedI've just installed a multiport serial card. This is an 8 port serial-only card. The main chipset on it is an ITE IT8871F.
I've got questions : Is there a driver I should try force loading on it (and if so, what options to use)?
PCI to Serial Quad 8-port Controller Card
Chipset: ITE 8871
on:
Ubuntu 10.10 Linux Server - Linux ubuntu 2.6.35-22-generic
lspci -vv show:
lshw show:
lspci -xxx show:
I am recently trying to get a steady wireless connection running. I am currently using the default settings/driver Fedora 13 is stocked with. As my internet browsing is somewhat up and down in load times, I decided to check in a video game which is generally a good test for me. haha I am harshly spiking and cannot find the source of my problem so my guess is a driver issue.
lspci | grep Network:
Code:
Code:
It is is seemingly right, my Windows 7 harddrive works just fine, this is just one last of the few issues I'm having from fully formatting my winblows HD to use as Linux storage.
I cannot find any native AR5008 Linux Drivers for my card and it has been a frustrating day. I guess I'm not cut to be a network analyst just yet.
System specs:
ASUS P5Q SE/R
Intel Core 2 Quad Q9550
4GB DDR2 667
Gigabyte GTX465 1G
TP LINK TL-WN851N Wireless card
I have just installed an Edimax EW-7612PIn PCI-E Wifi card which has an RTL8192SE chipset. This chipset is not supported under current F15 kernels so I have installed the driver and firmware from source and have that working fine. The driver can see the card and I can issue 'iwconfig' commands successfully enough to see my Wifi network.
The problem I have is that I don't understand the relationship between iwconfig and wpa_supplicatant and as I'm running a headless F15 server I cannot use the NetworkManager GUI to help me. I should also note that the Wifi network is using WPA2-Personal encryption.
This is what I have done:
Configured /etc/sysconfig/network-scripts/ifcfg-wlan0 with what I think are reasonable values (based on google searches), including the ESSID, TYPE as Wireless, etc.
Configured /etc/wpa_supplicant/wpa_supplicant.conf, including using the key value returned from wpa_passphrase.
Arranged for wpa_supplicant to run from boot, using chkconfig.
However when I run 'ifconfig wlan0 up' I get the error message 'link is not ready' and indeed looking at the output from 'iwconfig wlan0' there are no configured values. I also understand that some values are configured by iwconfig and others by wpa_supplicant, however it's not clear what.
How do I permanently set iwconfig values?
How do I configure wpa_supplicant?
I got a problem with tv card...i just instal tvtime program for watching analog tv station, but i cant see nothing, this is snapshoot from info about card.
[url]
and from tvtime program
[url]
It always fails when I try the sound card test. It says like the system cant detect the sound card.
Sound Card: 5 series / 3400 series chipset high definition audio
Module: snd-hda-intel
After searching about the issue, I found the information that installing kmod-alsa-PAE-1.0.20-1.el5.elrepo.i686.rpm and kmod-alsa-1.0.20-1.el5.elrepo.i686 would solve the problem.
But even I downloaded and installed them, nothing changed.
== BEGIN uname -rmi ==
2.6.18-194.17.1.el5PAE i686 i386
== END uname -rmi ==
== BEGIN rpm -q centos-release ==
centos-release-5-5.el5.centos
== END rpm -q centos-release ==
== BEGIN ls /etc/yum.repos.d ==
CentOS-Base.repo
CentOS-Media.repo
elrepo.repo
epel.repo
epel-testing.repo
mirrors-rpmforge
rpmforge.repo
rpmfusion-free-updates.repo
rpmfusion-free-updates-testing.repo
rpmfusion-nonfree-updates.repo
rpmfusion-nonfree-updates-testing.repo
== END ls /etc/yum.repos.d ==
== BEGIN lspci ==
~
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05)
~
== END lspci ==
== BEGIN lspci -n ==
~
00:1b.0 0403: 8086:3b56 (rev 05)
~
== END lspci -n ==
I can't use my wireless card in slack 13.1 (slack64-current). Looking at the dmesg output I saw that the firmware was missing, so I download it from ralink website.After this I was able to up it with ifconfig. I also was able to see my network with wicd, but after connection I can only transfer very few packets and network becomes unresponsive, no traffic.In slack64 13.0 this same card works fine. I don't even need to install a firmware. how I can make this work in slackware64-current?
View 6 Replies View RelatedDoes the rt61 dlink wifi adapter work with slackware 13?
Code:
I have a HP Pavilion dv2000 and can not figure out what chipset I have.
/sbin/lspci brings up the following
bunnyman@linux-bqo4:~> /sbin/lspci
00:00.0 Host bridge: Intel Corporation Mobile Memory Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile Integrated Graphics Controller (rev 0c)
00:02.1 Display controller: Intel Corporation Mobile Integrated Graphics Controller (rev 0c)
[Code]....
where I can get the .inf file from? I took windows completely off of the computer and dont want to reinstall it just to get the driver.
