I just built a new Intel i7 box with a DP55KG motherboard and soft RAID1. I installed AMP, ssh, and a few other apps. It is running 64-bit Ubuntu Server 10.04LTS. The box is really chewing on the RAM. is it the 64-bit talking?
View 2 RepliesI'm trying to build a Fedora 12 cluster to run DHCP on top of two servers using pacemaker and drbd. The pacemaker runs great but i'm having the hardest time getting DRBD installed.
My kernel version is 2.6.32.11-99.fc12.i686.PAE First i tried to [root@dhcp-primary drbd]#yum install drbd this doesn't give me everything because apparently the kernel module for DRBD must be built from source. so i unpacked drbd-8.3.6.tar.gz and tried :
[Code]...
I'm not very experienced in compiling from source i'd love to make an rpm for this but after scouring the web and trying different install methods, I am still at a loss.
I've got Ubuntu One syncing a single 25MB folder on 4 computers. On one of these computers, the ubuntuone-syncdaemon process constantly pegs the CPU, using from 50-80% long after any sync-able files have been modified and successfully synced. The process is only using 8.9MB of RAM.
Specs:
Ubuntu 10.04 (lucid)
Kernel 2.6.32-24-generic
1000.8 MB RAM
Pentium 4 2.53GHz
Free disk space: 280.9 GB
System monitor shows 56.8% total RAM usage, 15.4% swap file usage.
I started building my server with the following goals:Quiet - it will live in a cabinet in my living room, so it should be as quiet as possible Low power consumption - not just to keep the heat (ergo cooling demands, ergo noise) down, but also to save money since it will be on 24/7 High reliability Support for 8 IDE and 2 SATA drives. (Toward this end, I have two 2-port IDE PCI controller cards and one 2-port SATA IDE controller card.) Spend as little as possible. (Money is VERY tight for me right now.)
I started with a mini-itx board I had lying around. It's fanless, with a Via Epia 700MHz CPU in it. A little anemic, but it draws very little power and is dead silent. The problem with this board is that it has 2 IDE ports on board, no SATA ports, and only one PCI slot, so I have to choose between my SATA card and my IDE card. I need - but can't have - both. I tried buying a 2-slot PCI riser card, but apparently it's incompatible (or DOA) - none of my PCI cards work when connected via this riser card. I've looked for PCI cards that have 2 x IDE + 2 x SATA ports, but anything that fits that bill is very expensive.
Now I'm thinking new motherboard & CPU - preferably something older that can be had cheaply on ebay. If it uses DDR memory (rather than DDR2), I can use the RAM I have, which saves me $25. A newer Atom-based board would be OK, but they all seem to have one PCI slot -- and not enough IDE/SATA ports to get the job done with just one PCI slot. If you can recommend a motherboard that meets all the criteria above, please post it. (Or, if you have any other ideas for handling this very cheaply, let's hear it!)
Am trying to build a main frame computer, in order to learn more about them.
View 9 Replies View RelatedI am looking for the best/cheapest way to build a ubuntu server with 8tb of storage hanging off of it.
I don't feel it needs to be hardware raid, so more software raiding swap in and out failed disk drives.
The server itself normal duo core CPU with 2Gb of memory and i would like to have the internal drive of the O/S only.
Looking for suggestions on what tools to use. I'm a finance major with limited programming knowledge. I would like to start collecting my own stock data. I would like to pull data from google finance or something similar. Also, I subscribe to data from AAII, American Asso. of Individual Investors, and would like to add that data into the database. and be able to have a nice gui to run queries on. My interests are finding if there are various different arbitrage opportunities and fundamental value investments.
Very low budget. Want to run it on ubuntu. I was looking at Postgre SQL as the database, but really have no idea what is optimal. Not to sure on the gui or how to pull the data. If anyone is interested in the topic and would like to help me set up and run algorithms let me know too.
Is there a way to build a form so an admin can enter and add values to a database:
Example
Code:
use squid
insert into passwd values('testuser','test',1,'Test User','for testing purpose');
Is there a free software or an easy to configure script?
I build a LAMP server behind a router. The current situation is:
1.I could access index.html of apache within the LAN.
2.I could access the vsftp outside of the LAN.
3.I could access the ssh outside of the LAN.
I have configured my router to do reflections(although I don't know it's correct or not.). I think the LAMP works good since I could use it inside the LAN. The configuration of the router is at least partly right because ssh and vsftp work fine(I test by browsing the ip:74.***.***.*** in the lan, not 192.168.1.8 --this also works. ).
I cannot access web service outside the LAN. And the error message is "Oops! Google Chrome could not connect to 74. Did I miss some configuration of router?Apache2?Ubuntu? I use the ubuntu server 2010.10 version.
This is what im trying to do with the NAS, i would like it to stream movies 720 and 1080 to my Samsungs tvs, this may require trans coding(i think that the word), storage wise i would like to start with 2 2tb hardrives(The energy ones), i don't know if i need a raid(5) card for what i need if so, whats a good one ?
I would like to save as much power as possible.
Motherboard ?
CPU = maybe an I3
RAM = 2g DDR3
Power-supply = ?
OS = FreeNas
Also i have read a lot of places were you can do a automatic bit-torrent clients to downloads show and unrar them for you and maybe organize them in to separate folder, but my question is can i do this with megashare and Hotfile (premium) links ?
I am a total noob in the process of trying to build my own server. I installed Ubuntu 10.10 but when I did that I didn't have the computer hooked up with an ethernet or have any internet connection. During the installation process it was unable to set up DHCP, so I figured I would just do that later, somehow.
Anyways, I recently hooked up an ethernet cable from the server to another computer, which has internet.
I've been slowly working my way through the Server Documentation and am on the Networking chapter. It has given me the commands to install wireless-tools, ethtool, dhcp3 server and I've also tried to install gedit. Every time it gives me the error: E: Unable to locate package XXX
When I ran the sudo lshw -class network command I find that it recognizes both an ethernet interface as well as a wireless interface(my wireless adapter). BOTH of them say *-network DISABLED.
My goal is to enable both of those, but I am assuming I need to be able to locate the packages first. I installed the server edition using a USB pendrive. I still have the files on the pendrive, but I don't know how to make the server locate those files. I'm guessing it wants to access the installation files to locate the packages to install.
I'm trying to move an existing webserver from an old machine to a machine with Fedora 12 installed on it. ThSince the version available in the repository is version 2.X I downloaded the source from apache.org and tried to compile it. I ran configure using the default options and it an without any warnings or errors. However when I run make it fails with the following error:
gcc -c -I../os/unix -I../include -DLINUX=22 -DHAVE_SET_DUMPABLE -DUSE_HSREGEX -DNO_DL_NEEDED `../apaci` htpasswd.c
htpasswd.c:101: error: conflicting types for getline
/usr/include/stdio.h:653: note: previous declaration of getline was here
make[2]: *** [htpasswd.o] Error 1
make[2]: Leaving directory `/root/apache_1.3.41/src/support'
make[1]: *** [build-support] Error 1
make[1]: Leaving directory `/root/apache_1.3.41'
make: *** [build] Error 2
what the problem and more importantly the solution to this problem is?
i have a project from my boss to make radius server on fedora 13 i 686. can u tell the step by step how to build radius server on fedora 13???? thx u for sharing
View 3 Replies View RelatedI start to build up IMPS to my server. Any ideas where to start? Any experience so far. I this think yamicocom like service. And about 5 bugs to get in. What you think? I need to put some extra to this basic concept.
View 2 Replies View RelatedI need to build a 3 node web server cluster to run a php application. Since the app requires users to login (which means a session state is to be maintained), I will be sharing sessions save path, I also need to share the application directory across 3 nodes. I having trouble deciding which cluster file system to select.
View 5 Replies View RelatedI have an init script running as a special build user which performs an automated build that fails with (Too many open files).I updated /etc/security/limits to allow the special user more open files, but that didn't work - the init script still isn't allowed more open files.Here's a demonstration of the problem;
Code:
$ su - sbsbuild -c "ulimit -n"
Password:
[code]....
I'm in love with my Opensuse 11.2. Love my KDE 4.4. The only thing I miss from my Ubuntu installation, is the ability to use Boxee. I would be more than willing to compile Boxee from source. I only have 2 problems with that:
1) I don't know where I can find all the build-deps or what they are for that matter to build Boxee.
2) I'm running on a Netbook. Yes, my measly Intel Atom is no fun for compiling and building.
What are my options/what can I do to get Boxee up and running on 11.2? I've tried searching on build service for an RPM, but I think due to legal restrictions, Boxee can't be on there.
looking for LIBEVENT... configure: error: Package requirements (libevent >= 2.0.10) were not met: In order to build transmission 2.21.I need libeventnew version of transmission,I need to build libevent-dev >= 2.0.10 and installed first.But I can't get any information about building development files for libevent.
View 1 Replies View Relatedas I'm advancing in building some nice rpm I finally wanted to install on of my gems also the build was successful the actual install fails with missing dependencies.
Code:
$ rpm --root /home/sascha/rpmbuild/ -i ./RPMS/x86_64/memcached-1.4.1-2.x86_64.rpm
error: Failed dependencies:
libc.so.6()(64bit) is needed by memcached-1.4.1-2.x86_64
libc.so.6(GLIBC_2.2.5)(64bit) is needed by memcached-1.4.1-2.x86_64
[code]....
Trying to install SW 13.1 (on DVD) on the following system: M/B Intel: DX38BT Processor Intel Core 2 Quad Q6700 - 2.66GHz, 8MB Cache, 1066MHz FSB, Socket 775 Memory Corsair Dual Channel 8192MB PC10600 DDR3 1333MHz Memory (4x2048MB) Graphics Diamond Radeon HD 3850 Video Card - Viper, 512MB GDDR3, PCI Express 2.0 P/S Ultra 1000W
My goal is to install the i386 build on one partition and the 64-bit build on another. I have been away from Linux for a while and am sick to death of Win7, want to come home. :-}
Booted on i386 side of DVD, system freezes after a couple of lines that start with ATA2. Does not respond to 3 finger salute, ctrl-c, nothing. Have to press reset. I have tried both huge.s and hugesmp.s kernels
Booted on 64-bit side, comes up fine. I performed the install, selected for automatic lilo install. Lilo install hung but I was able to reboot. I booted off the 64-bit side again, entered the following: huge.s root=/dev/sde3 rdinit= ro It booted fully to the login prompt but the keyboard does not work, no input.
Ant was installed in yast2 but will not run since build.xml was never created. How can this be fixed? I would like to run AudioTool.
View 5 Replies View RelatedI am trying to build a multiseat linux system(Build a Six-headed, Six-user Linux System LG #124). I am posting some outputs output of lspci | grep VGA
Code:
00:0d.0 VGA compatible controller: nVidia Corporation C61 [GeForce 6150SE nForce 430] (rev a2)
02:00.0 VGA compatible controller: nVidia Corporation G98 [GeForce 8400 GS] (rev a1)
ls /dev/input/mouse*
Code:
/dev/input/mouse0 /dev/input/mouse1 /dev/input/mouse2
more /proc/bus/input/devices
[Code]...
I am having trouble in configuring xorg.conf. I am running Suse 11.3 desktop on my PC. Also, I have one onboard nvidia graphics 6150SE and I have put one nvidia 8400GS 512Mb in the 16X PCIe slot for the additional seat...
So kindly tell me what should I do now or what things are missing ?? For any further info abt my PC plz tell me to post outputs(specify the commands for the same..)
Actually it appears to build just fine, but segfaults when run it
I'm following the recipe from here after downloading and extracting the tarball: [URL]
Compiling kst using automake:
Code:
./configure --prefix=/usr
make
sudo make install
Everything appears to work but running the application fails with sigsegv
Actually the --prefix=/usr causes the apt-get installed kst to be overwritten, but I tried --prefix=/home/wally first and then did make clean with the "documented" command after it created code that crashed. Uninstalling and re-installing kst in synaptic got my 1.5.1 kst back, but its got some issues I hope have been fixed.
I need to use Ubuntu 8.04 for this right now, but 10.04 has kst 1.7.1 which still has the issue so I'd need to build it there eventually too
In case you've never heard of Kst, its graphing program that when reading stdin can be used as a real-time strip-chart display. The issues I have with the repo versions are --geometry option doesn't change the window start up size and the -F option (to start up with a *.kst file for nice labels and layout and use stdin for real-time data).
I'm new both to database and database in Ubuntu. I am working on a project in school which students are told to go to a site (html? ftp?), and read a document. I need to record the names of the students who read a document onto a spreadsheet. I was told to look into MySQL and Ubuntu. How can I proceed with this in Ubuntu?
View 1 Replies View RelatedHave anybody managed to build cantara v1.7. in ubuntu 10.04? I can't get it working...
View 1 Replies View RelatedI've downloaded vlc 1.1.4.1.tar.bz2 from the internet, as I have problem using the 'sudo apt-get' command which is due to the fact that my USB Internet Modem provider didnt cared to make it compatible with Linux. I presently connect to internet using Nokia PC Suite [available only in Windows, as you all may know] to browse the net. Currently I've a dual-boot with Ubuntu 10.04 and Windows 7.
I tried building it by following the instructions in the INSTALL file, but it wont just work!
I was wondering, is there ever more than one build of a given Ubuntu release (but with the same major/minor version)? That is, if I download X.10 a month after it comes out, and then I download it a few days before the next version is released, say, will it be bit-for-bit the same as the one I originally downloaded? Or does the Ubuntu team do new builds over time, fixing things, etc.?
View 2 Replies View RelatedWhen you build depenancis with apt=get for any package you are going to install from source which directory do the depenacies go into? And I build the package from for example /home/lex1 will those dependancies be found In this case the only command I need to run (which is not normal) is ./Install
View 1 Replies View RelatedI know this is off Ubuntu topic, but, imo, Ubuntu is the best forum for answers on the internet.Anyone using one of these online editors ?I use it as integrated into a CMS, but would like to build it into some web pages - with sole purpose of EDITING MY WEBPAGES ONLINE. Kompozer is great, but has a mack truck hole that may never get filled and I find the (usage) simplicity of ckedit attractive.Problem is I am not able to grasp how to do it.The examples are gobbledeegook to me. I mean i try them, they work, but do not address how to integrate (maybe just over my head).Installation and usage is trivial, I just cannot grasp how (if possible) to integratethe editor INTO a webpage - better yet, direct it to a webpage.
View 1 Replies View RelatedJust like title.can i disable mmu, and build it? how to do that?
View 4 Replies View Related